Casio Watch 2263-1 User's Manual
Contents
1. Be sure to always keep separate written copies of all important data e Malfunction or repairs e Dead battery e Battery replacement In no event will CASIO be liable for loss of data or any damages arising out of such loss J Mode indicator The File Mode lets you store up to 30 pairs of name and telephone number data The name can be up to 8 characters long and the number up to 12 digits Data is automatically sorted into alphabetical order based on the name data You can recall data by scrolling through it on the display e f you do not operate any button for a few Number minutes while in the File Mode the watch area automatically goes back to the Timekeeping Mode Name area Alarm Mode 1 In the File Mode press or until the new data display appears e f the message FULL appears on the display it means that memory is full To store more data you will first have to delete some of the data 2 Hold down until the flashing cursor appears on the name area 3 Use or to input a character at the cursor Remaining position The character changes in the memory following sequence Holding down either New data display button changes the character at high speed Press gt 3 gt space AtoZ a O09 lt e lt lt Press __ 4 After you select the character you want press to advance the cursor to the right e Repeat steps 3 and 4 until you complete na2. e The format 12 hour and 24 hour of the alarm time matches the format you select for normal timekeeping e When setting the alarm time using the 12 hour format take care to set the time correctly as morning no indicator or afternoon P 4 After you set the alarm time press to return to the Alarm Mode e If you do not operate any button for a few minutes while a selection is flashing the flashing stops and the watch goes back to the Alarm Mode automatically To switch the daily alarm and hourly time signal on and off Press while in the Alarm Mode to change the status of the daily alarm and hourly time signal in the following sequence Alarm on indicator Hourly time signal on indicator ALM SIG a e imeem ALM SIG ALM SIG ALM SIG ALM SIG Both ON Both OFF Daily Alarm Hourly Time Only Signal Only To test the alarm Hold down O while in the Alarm Mode to sound the alarm STOPWATCH MODE The Stopwatch Mode lets you measure elapsed time split times and two finishes The range of the stopwatch is 59 minutes 59 99 seconds Mode indicator Current time Seconds Minutes 1 100 seconds o Elapsed time measurement Start Stop Re start Stop Clear Split time measurement Start Split Split release Stop Clear c Split time and 1st 2nd place times D A MM 0 c A _ A Start Split Stop Split release Clear First runner Second runner Record time of finishes fini
3. Module No 2263 2263 1 GENERAL GUIDE e f the contents of the display seem to be continually changing see AUTO DISPLAY FUNCTION for information on how to stop it e Press to change from mode to mode e In any mode press to illuminate the display for about two seconds Caution e The backlight of this watch employs an electro luminescent EL light which loses its illuminating power after very long term use e Frequent use of the backligfht shortens the battery life e The watch emits an audible sound whenever the display is illuminated This is because the EL light vibrates slightly when lit It does not indicate malfunction of the watch Timekeeping Mode File Mode TIMEKEEPING MODE This watch lets you select any two of 40 cities TIME 1 TIME 2 as basic Timekeeping Mode times Hold down to toggle the Timekeeping Mode between TIME 1 and TIME 2 e You can display either the city code or year Press to toggle between display of the city code and year City code Day of week Year Month Day cy Press a Be DST on indicator To set the time and date Setting the time and date for either of the basic times TIME 1 or TIME 2 automatically adjusts the settings of the other basic time e You can turn daylight saving time DST on and off independently for TIME 1 and TIME 2 1 While in the Timekeeping Mode hold down until the City Code flashes on the display 2 Press t
4. input File data steps 3 through 4 for name input or 6 through 7 for number 5 After editing the data press to store it To delete File data 1 In the File Mode use and to scroll through the data items and display the one you want to delete 2 Hold down until the flashing cursor appears on the display 3 Press and at the same time to delete the data item e The message CLR clear appears on the display for a few seconds e At this time the cursor appears on the display ready for input 4 Input data or press to return to the File Mode ALARM MODE Mode Alarm on When the Daily Alarm is turned on the alarm indicator indicator sounds for 20 seconds at the preset time each day Press any button to stop the alarm after it starts to it la sound When the Hourly Time Signal is turned on indicator the watch beeps every hour on the hour e The alarm sounds when the time selected for basic timekeeping in the Timekeeping Mode TIME 1 or TIME 2 matches the alarm time you set To set the alarm time 1 Hold down while in the Alarm Mode The hour digits flash on the display because they are selected At this time the Daily Alarm is turned on automatically Minutes Current time 2 Press to change the selection in the following Hour sequence Hour jx gt inte 3 Press to increase the selected digits and to decrease them Holding down either button changes the selection at high speed
5. me input e You can input up to 8 characters in the name area 5 After the name input is through use to move the cursor to the number area 6 While the cursor is in the number area use or to input a number you want The character changes in the following sequence Holding down either button changes the character at high speed Press gt a Hyphen 0to9 Space Press o a8 7 After you select the character you want press to advance the cursor to the right e Repeat steps 6 and 7 until you complete number input 8 After inputting the data you want press to store it into memory e The message SORT appears on the display for a few seconds e The name area shows only 5 characters but automatically scrolls from right to left to show all of the characters that make up the text To scroll through File data In the normal File Mode when the display is not flashing press to scroll forward or to scroll backward through stored data e The data item that is displayed when you exit the File Mode will be the first data to appear when you enter the File Mode again To edit File data 1 In the File Mode use and to scroll through the data items and display the one you want to edit 2 Hold down until the flashing cursor appears on the display 3 Use to move the cursor to the character you want to change 4 Use or to select the character you want e For details see To
6. o change the selection flashing in the following sequence City Code gt DST Seconds Hour Minutes Day i lt Month Year lt ee beg 3 While the seconds setting is selected flashing press to reset it to 00 If you press while the seconds setting is in the range of 30 to 59 the seconds are reset to 00 and 1 is added to the minutes If the seconds setting is in the range of 00 to 29 the minutes count is unchanged e While City Code setting is selected flashing press or to scroll through the City Code For full information on City Code see the CITY CODE TABLE e While the DST setting is selected press to toggle it ON and OFF e While the 12 24 hour format setting is selected press to toggle it between 12 and 24 e While any other setting is selected flashing press to increase it or to decrease it e Holding down either button changes the setting at high speed 4 After you set the time and date press to return to the Timekeeping Mode e The day of the week is automatically set in accordance with the date e The date can be set within the range of January 1 1995 to December 31 2039 e If you do not operate any button for a few minutes while a setting is flashing the flashing stops and the watch goes back to the Timekeeping Mode automatically FILE MODE r Caution The following causes all data stored in memory to be deleted
7. shes second runner Record time of first runner AUTO DISPLAY FUNCTION The Auto Display function of this watch continually changes the contents of the display Note that you cannot use any of the watch s other functions while the Auto Display function is operating To turn the Auto Display on Hold down for about two or three seconds in any mode until the watch beeps To turn the Auto Display off Hold down for about two or three seconds until the watch beeps At this time the watch is in the Timekeeping Mode Note The Auto Display function cannot be performed while you are making settings i e while digits or other setting are flashing on the display City Code CITY CODE TABLE ADELAIDE 2263 2 GMT differential ANCHORAGE BERLIN BANGKOK CAIRO CARACAS CHICAGO DHAKA DELHI DENVER DUBAI GUAM HONG KONG HONOLULU ISTANBUL JEDDAH JERUSALEM KABUL KARACHI LOS ANGELES LONDON MEXICO CITY MIAMI MILAN MALE NOUMEA NEW YORK PARIS PAGO PAGO YANGON RIO DE JANEIRO ROME SEOUL SAN FRANCISCO SINGAPORE SYDNEY TEHRAN TOKYO WELLINGTON VANCOUVER Based on data as of December 1997
Download Pdf Manuals
Related Search