Home

Carbine PLUS-5600 User's Manual

image

Contents

1. A The horn siren will chirp one time B The LED indicator will begin to flash slower C The parking lights will flash one time D All protected entrances are armed Note 1 Re opening a protected entrance before the system becomes armed will stop the arming timer After closing the entrance the timer will begin counting again from zero Note 2 If the vehicle has a delayed interior lighting system the automatic arming timer will start counting after the interior lighting has turned itself off This could add up to 45 seconds to the total automatic arming countdown time Up to 75 seconds total arming delay The security system is now fully armed Disarming the Security System Using the Transmitter 1 Press and release the UNLOCK button on the transmitter The security system will respond as follows A The horn siren will chirp two times B1 The LED indicator will be off Only if Auto Arming is programmed off B2 The LED indicator will be flashing very fast Only if Auto Arming is programmed on C The parking lights will flash two times Note If you are disarming the security system after it has been triggered and the horn siren is sounding the disarm chirps are automatically deleted Disarming the Security System Using the Passive Transmitter B Note When using the passive transmitter the on off switch must be in the on position A Walk toward your vehicle and the security system will respond the s
2. Sirens transmitters wire harness or any accessory item are covered by our standard 12 month limited warranty Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential or incidental damages or claims that may arise due to failure of product to operate properly except those accorded by law Magnadyne s or its authorized agents liability to the repair replacement of the product as stated above if all conditions of the warranty are met No expressed warranty or implied warranty is given except those set forth herein Magnadyne does not warrant or guarantee against break in damage or the theft of the vehicle in part or whole or against the loss or damage to the contents of any vehicle in which a security system is installed Magnadyne security systems are only a deterrent against possible theft This warranty extends only to the original purchaser of the product and for the vehicle in which it was originally installed This warranty is not transferable or assignable to any person or vehicle Defective merchandise should be returned to the original point of purchase or secondly to Magnadyne Corporation 1111 W Victoria Street Compton CA 90220 A return authorization must be obtained before sending or merchandise may be refused 02 01 02 Rev A PLUS56UM
3. button for more than 3 seconds and the security system will respond in the following manner A The horn siren will begin sounding B The parking lights will begin flashing To turn off the panic alarm press and release the UNLOCK or PANIC button on the transmitter The horn siren will stop sounding and the parking lights will stop flashing Note 1 If you do not turn off the panic feature with the transmitter the panic alarm will sound for 60 seconds and then turn off by itself Note 2 The panic button on the 4 button transmitter can be programmed to operate as the channel 3 button and not as a panic button If the panic button has been programmed to operate channel 3 by pressing and holding down the lock button you can activate the panic feature PLUS5600UM 2 1 02 11 48 AM Page User Discretion Silent Arming Your Carbine security system can be instructed to become armed or disarmed without the horn siren chirps by the remote transmitter To operate this feature at any time simply press the LOCK and UNLOCK buttons at the same time to arm or disarm your security system without the chirp indications 60 Second Re Arming If your Carbine security system has become triggered the horn siren will sound for 60 seconds and then stop and re set to a fully armed condition Note If a protected entrance is left open your Carbine security system will remain triggered for two more 60 second cycles then fully re
4. PLUS5600UM 2 1 02 11 48 AM Page Se Em Fe ER EE ee A Vehicle Security OWNER S MANUAL Model PLUS 5600 This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Note The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment Copyright 2002 Magnadyne Corporation PLUS5600UM 2 1 02 11 48 AM Page Congratulations on your purchase of a quality Carbine Automotive security system Carbine automotive security products have been designed to provide the consumer with a product that is technologically superior and will provide years of trouble free operation The information enclosed will provide a ready reference of the operation and maintenance of your new Carbine security system Remote Control Transmitters Regular Look DA Passive Unlock A Y Panic Passive Aux Unlocking Security System Operation Using the transmitter to arm the security system 1 Exit the vehicle and close all entrances 2 Press and release the LOCK button on the transmitter The security system will respond as foll
5. ame as pushing the unlock button on the transmitter The security system is now disarmed Removable Valet Override Switch Operation To provide a higher level of protection your Carbine security system is supplied with the patented removable valet switch system The removable valet switch is used to override the security system in the event that the transmitters are lost or fail to operate and to put the security system in non operational mode valet for vehicle servicing etc Caution Be careful and not to bend the override switch pins when put it into the housing Also note the override switch can only go into the housing one way See diagram to note shape of housing Off On Positon Positon uw fT Me PLUS5600UM 2 1 02 11 48 AM Page Removable Valet Override Switch Operation Continued Override Operation Security System is Armed 1 Enter the vehicle The security system will begin sounding at this point and place the override switch into the switch housing Make sure that the switch button is in the off position 2 Place the ignition key into the ignition switch and turn the ignition switch to the on position 3 Within 5 seconds of turning the ignition key on place the valet switch to the on position 4 The horn siren will stop sounding 5 The LED indicator will be solid red The security system is overridden and is now in the valet mode N
6. arm excluding the door input trigger Door input trigger is no longer functional Closing the entrance will re set the door input trigger within 7 seconds Secondary RF Protection Mode Every time you disarm your Carbine security system with your transmitter the security system will start an RF protection mode countdown This is a timed secondary protection mode to insure that after the system is disarmed by radio signal it will count down for 60 seconds and then become re armed if no one enters the vehicle Note The feature is only active when the security system has been programmed to automatically arm Alarm Mode Indicators 1 The LED indicator will provide information on 7 modes of security system operation LED is off Security system is disarmed LED is flashing Security system is armed LED is flashing fast Automatic arming timer or RF protection mode timer is counting down LED is on solid Security system is in valet mode Only when the ignition key is on LED is flashing once every 5 seconds Security system is in valet mode Only when ignition key is off LED is flashing in a 2 flash pause sequence Tamper warning security system has been trigger from the hood trunk switch or electronic sensor LED is flashing in a 3 flash pause sequence Tamper warning security system has been triggered from an opened door 2 The horn siren will provide information on four modes of security sys
7. ating properly The batteries supplied with your transmitter will usually last about 1 year Heavier usage will shorten battery life Reduced transmitter range is usually a sign that the battery in the transmitter is becoming weak and should be replaced Note The battery supplied with transmitter A will last about 1 year The battery supplied with transmitter B and C will last about 6 months Refer to the remote control transmitter drawing at the beginning of this manual Battery Replacement Replacement batteries for your transmitter are available in most drug stores and camera shops To replace the battery remove the small Phillips screw from the transmitter case and pull apart the top and bottom case halves Remove the battery from it s holder Insert the new battery in place of the old one observing the batteries polarity Gently snap the top and bottom case halves together DO NOT force them together and replace the Phillips screw DO NOT over tighten the screw Replacement Transmitters In the event that the transmitter supplied with your Carbine security system becomes damaged or lost return to the installation facility that installed your security system to purchase a new one Limited Lifetime Warranty Magnadyne Corporation or its authorized agents will for the life of the vehicle and to the original purchaser repair replace or refund the retail sales price of said product or any part thereof at the option of the Magnadyn
8. e Corporation or its authorized agents if said product or part is found defective in materials or workmanship when properly connected and operating on the correct power requirements designated for the specific product This warranty and Magnadyne Corporation or its authorized agents obligations hereunder do not apply where the product was damaged while in the possession of the consumer subjected to unreasonable or unintended use not reasonably maintained utilized in commercial or industrial operation or serviced by anyone other than Magnadyne Corporation or its authorized agent or where the warning seal on the product is broken or the power plugs or wires are detached from the unit Magnadyne Corporation or any of its authorized agents do not assume any labor costs for the removal and reinstallation of any product found to be defective or the cost of transportation to Magnadyne Corporation or its authorized agents Such costs are the sole responsibility of the purchaser This warranty does not cover the cabinet appearance items normal wear and tear or accessories used in connection with the product resulting from improper installation alteration accident misuse abuse or acts of nature This Limited Life Time Warranty applies only to the receiver section of the security system Neither the siren transmitters wire harness or any accessory item added to or used with a Remote Mobile security system are covered by this Limited Life Time Warranty
9. e horn siren This single chirp is a pre warning if a would be thief is attempting to enter your vehicle Zone 2 detects heavier impacts that are considered threatening and immediately triggers your security system by sounding the horn siren and flashing the parking lights PLUS5600UM 2 1 02 11 48 AM Page as Programmable Features The following is a brief description of the operation of each programmable feature Any adjustment to the operation of these features must be performed by the dealer who installed your Carbine Security System These features are not user adjustable Ignition Key Controlled Door Lock Unlock Remote door lock unlock option must be installed With this feature activated the door lock system of the vehicle will become locked 3 seconds after the ignition key is turned to the on position All doors When the ignition key is turned to the off position the door locks will immediately become unlocked All doors Note This feature has 3 modes in which it can operate Mode 1 operates as explained above and is the most common operation Model 2 locks the doors when the ignition key is turned on but does not unlock the doors when the ignition key is turned off In mode 3 the ignition key locking feature is off Chirp Status Indicator Delete Permanent Chirp Delete De activating the chirp indication system will eliminate the arm and disarm chirp indicators For your safety the tamper warning chirp indicat
10. itter The interior lighting will remain on for 30 seconds after the security system is disarmed Turing on the ignition key will turn off the interior illumination before 30 seconds Option 4 Single Zone Shock Sensor Installing option 4 will increase the level of security provided by your Carbine security system If the shock sensor becomes activated the security system will immediately trigger your security system by sounding the horn siren and flashing the parking lights Option 5 Starter Disable Relay Adding option 5 will increase the level of protection that your Carbine security system can offer When the starter disable module is installed the vehicles engine will not crank when the alarm system is in the armed mode Option 6 Unlock Drivers Door First Requires option 1 to be installed Installing option 6 will allow your Carbine security system to unlock only the drivers door upon disarming the security system To unlock the remaining doors press the UNLOCK button once again within 3 seconds of disarming the security system The remaining doors will become unlocked Option 7 Dual Zone Shock Sensor Installing option 7 will increase the level of security provided by your Carbine security system Zone 1 of the dual zone shock sensor will detect lighter non threatening disturbances that would normally set off most sensors and trigger the security system If zone 1 is activated the security system will emit a single chirp from th
11. or will always be active Automatic Arming of Security System When the automatic arming of security system feature is programmed on the security system will automatically become armed 30 seconds after the last protected entrance is closed without requiring a signal from the remote transmitter Ignition switch must be off Automatic Door Locking Remote door lock unlock option must be installed If it is desired to have the vehicle s power door locking system become locked at the same time the security system becomes armed by the automatic arming of security system feature the automatic door locking programming should be on Safety Illumination Sentinel System SISS Programming on the Safety Illumination Sentinel System will proved the vehicle user with a lighted pathway to and from the vehicle when the security system is armed and disarmed With the SISS programmed on the parking lights and the dome light will remain on for 12 seconds after the security system is armed providing a lighted pathway while leaving the vehicle In addition the parking lights and dome light will remain on for 30 seconds after the security system is disarmed immediately drawing attention to your vehicle while providing a fully lighted vehicle interior and exterior PLUS5600UM 2 1 02 11 48 AM Page ss System Maintenance The only maintenance that your Carbine security system requires is a periodic check of it s operation to be sure that all functions are oper
12. ote 1 If the valet switch is already in the on position when you turn on the ignition key the override function will be bypassed Turn off the ignition key place the valet switch in the off position and try again Note 2 If you fail to place the valet switch to the on position within 5 seconds of turning on the ignition key the override function will be locked out Place the valet switch in the off position turn off the ignition key and try again Valet Operation The security system is already disarmed 1 Place the valet switch into the switch holder making sure that the switch button is in the off position 2 Turn the ignition key to the on position 3 Place the valet switch to the on position 4a The LED will be on solid indicating that the security system is in the valet mode Ignition key on 4b The LED will flash once every 5 seconds indicating the security system in in valet mode Ignition key off How to Get Back to Security System Activation Mode 1 Place the ignition key switch to the on position 2 Place the valet switch to the off position 3 Place the ignition key switch back to the off position You will notice that the LED indicator will be off This indicates that you have exited the valet mode and your security system will operate normally 4 Remove the valet switch Remote Panic Press and hold the LOCK or PANIC
13. ows A The horn siren will chirp one time B The LED indicator will begin to flash at a steady rate C The parking lights will flash one time D The starter disable device will become armed and the vehicle engine will not crank E All protected entrances are armed Note If the dome light is on or a sensor is active at the time you arm your security system You will hear the horn siren beep one time and then you will hear another beep from the horn siren about 5 seconds later This second beep is the active sensor warning indicator This second beep tells you that the alarm is armed but one of the sensors has been temporarily deleted because it was on at the time the alarm was armed The security system is now fully armed Automatic Arming Without Using the Transmitter Note The following information is valid only if your security system has been programmed to automatically arm 1 Turn off the ignition key and exit the vehicle 2 Close all protected entrances After the last protected entrance is closed the horn siren will chirp one time and the LED indicator will begin to flash fast The fast flashing LED indicates that the automatic arming timer is counting down and the security system will become armed within 30 seconds After 30 seconds has passed the security system will respond in the following manner PLUS5600UM 2 1 02 11 48 AM Page T Automatic Arming Without Using the Transmitter Continued
14. tem operation One horn siren chirp Security system is armed One horn siren chirp One more chirp 5 seconds after the first chirp Security system is armed but one of the sensors was on and the alarm has bypassed it The remaining sensors are armed Two horn siren chirps Security system is disarmed Four horn siren chirps Tamper warning security system is disarmed PLUS5600UM 2 1 02 11 48 AM Page Upgrade Options Option 1 Remote Power Door Lock Unlock Control Note Your vehicle must have an electronic door locking system for this feature to operate Installing option 1 will allow the remote transmitter supplied with your Carbine security system to lock and unlock your vehicle s doors as it arms and disarms your security system Option 2 Remote Trunk Hatch Release CH 2 Installing option 2 will allow the remote transmitter supplied with your security system to open your vehicles trunk or rear hatch Pressing the AUX x button on the transmitter for 2 seconds will open the existing power trunk hatch release mechanism Note Vehicles that are not factory equipped with an electronic trunk release system will require additional parts than a vehicle with a factory installed trunk release system Option 3 Dome Light Illumination Installing option 3 will allow your Carbine security system to turn on your vehicles interior illumination system at the time the security system is disarmed by the remote transm

Download Pdf Manuals

image

Related Search

Related Contents

Service Manual  An Authentication Framework for Nomadic Users in Ubiquitous  How to use the Peloris Dual Retort Rapid Tissue Processor  Samsung HT-TP12 Manuel de l'utilisateur  manual JLG210 170805  Leap Frog Learning Friend® Lily  Rudolph 10521 Instructions / Assembly  Bretford TPMUNI4 project mount  Fujifilm Sensia 200 135/36  MANUAL DE INSTALACION Y OPERACION  

Copyright © All rights reserved.
Failed to retrieve file