Home

Canon C2225 Owner's Manual

1. E Oo m 1 892 mm Do not attempt to disassemble or modify the If there is smoke or unusual noise immediately machine turn the main power switch OFF disconnect the power cord from the power outlet and then call your local authorized Canon dealer Using the machine in this state may cause a fire or electrical shock Also avoid placing objects around the power plug so that the machine can be disconnected whenever necessary V U I Some parts inside the machine are subject to high voltages and temperatures Take adequate precautions when inspecting the inside of the Do not turn the main power switch OFF or open machine Do not carry out any inspections that are the front covers while the machine is in operation not described in the manuals for this machine This may result in paper jams Be careful not to spill liquid or drop any foreign Do not use flammable sprays such as spray glue objects such as paper clips or staples inside the near the machine There is a danger of ignition machine If a foreign object comes into contact with electrical parts inside the machine it might cause a short circuit and result in a fire or electrical shock 26 This machine generates a slight amount of ozone etc during normal use Although sensitivity to ozone etc may vary this amount is not harmful Ozone etc may be more noticeable during extended use or lon
2. Printing Outputting a copy or outputting data sent from a computer to the machine Copying Printing data scanned from an original followed by finishing options such as stapling Legal Notices Product Name Safety regulations require the product s name to be registered In some regions where this product is sold the following name s in parenthesis may be registered instead imageRUNNER ADVANCE C2230 C2225 F163100 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Operator s Manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Use of shielded cables are required to comply with Class A limits in Subpart B of Part 15 of the FCC Rules Do not make any changes or modifications to the equipment unless otherwise specified in the manual If
3. or similar item refers to a printing device display device or item respectively that contains PostScript technology created or licensed by Adobe Systems Incorporated and not to devices or items that purport to be merely compatible with the PostScript language Adobe the Adobe logo PostScript the PostScript logo and PostScript 3 are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries Linux is a registered trademark of Linus Torvalds Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries All other trademarks are the property of their respective owners Adobe PDF The PDF logo is a trademark or registered trademark of Adobe Systems Incorporated in the United States and other countries Copyright 2008 Adobe Systems Incorporated All rights reserved Protected by U S Patents 6 185 684 6 205 549 7 213 269 7 272 628 7 278 168 Patents pending in the U S and other countries Allinstances of the name PostScript in the text are references to the PostScript language as defined by Adobe Systems Incorporated unless otherwise stated The name PostScript also is used as a product trademark for Adobe Systems implementation of the PostScript language interpreter Except as otherwise stated any reference to a PostScript printing device PostScript display device or similar item refe
4. 50 to 128 g m 50 sheets 21 Ib bond 80 m2 Original Scanning Speed Copying 1 sided scanning 30 sheets minute LTR in Black and White Full Color at 600 dpi Scanning 1 sided scanning 51 sheets minute LTR in Black and White Full Color at 300 dpi Power Source Consumption From the main unit Approximately 30 W Dimensions H x W x D 5 3 8 x 22 1 4 x 21 1 4 135 mm x 565 mm x 540 mm Oo ttem Specifications OOO O O Paper Sizes 11 x 17 LGL LTR LTRR STMTR 12 x 18 EXEC and Custom size 5 1 2 x 7 1 8 to 12 x 18 139 7 mm x 182 mm to 304 8 mm x 457 2 mm Paper Drawers Capacity 550 sheets x 2 cassettes 21 Ib bond 80 g m 680 sheets x 2 cassettes 17 Ib bond 64 g m Power Source Maximum Power From the main unit Approximately 30 W Consumption Dimensions H x W x D 9 3 4 x 22 1 4 x 25 5 8 248 mm x 565 mm x 650 mm Weight Approximately 60 6 Ib 27 5 kg COM10 No 10 10 com Dimensions H x W x D 3 1 4 x 17 1 4 x 12 1 8 81 mm x 439 mm 307 mm Weight Approximately 2 6 lb 1 2 kg 39 Staple Finisher M1 tem Specifications Paper Size Weight Type Size 12 x 18 12 5 8 x 17 11 16 11 x 17 LGL LTR LTRR STMT STMTR EXEC Custom size 3 7 8 x 5 1 2 to 12 5 8 x 18 99 mm x 139 7 mm to 320 mm x 457 2 mm and Envelopes Weight 17 lb bond to 80 Ib cover 64 to 220 g m Type Thin Plain 1 18 to 22 Ib bond 65 to 82 g m Plain 2 22 to 26 Ib bond 83 to 99 g m Plain
5. Continued use of a damaged power cord can lead to an accident such as a fire or electrical shock The power cord should not be taut as this may lead to a loose connection and cause overheating which could result in a fire If excessive stress is applied to the connection part of the power cord it may damage the power cord or the wires inside the machine may disconnect This could result in a fire Avoid the following situations Connecting and disconnecting the power cord frequently Tripping over the power cord The power cord is bent near the connection part and continuous stress is being applied to the power outlet or the connection part Applying excessive force on the power plug Moving the Machine If you intend to move the machine even to a location on the same floor of your building contact your local authorized Canon dealer beforehand Do not attempt to move the machine yourself Provide Adequate Installation Space Provide enough space on each side of the machine for unrestricted operation The following measures are for the imageRUNNER ADVANCE C2230 When no optional products are attached 100 mm or more 1 139mm When the Inner Finisher F1 and Copy Tray J1 are attached 250 mm or more 1 139 mm 25 When the Booklet Finisher M1 and Buffer Pass Unit K1 are attached 100 mm or more
6. in height Staple mode LTR and EXEC 1 700 sheets 30 sets or 9 5 8 243 mm in height 11 x 17 LGL and LTRR 650 sheets 30 sets or 3 3 4 96 mm in height No finishing set Collate Group mode with different paper sizes 650 sheets or 3 3 4 96 mm in height Staple mode with different paper sizes 650 sheets 30 sets or 3 3 4 96 mm in height 40 tem Specifications S O Max Stapling Capacity Available Corner Staple Double Staple mode Staple Size LTR and EXEC 50 sheets 18 to 22 Ib bond 64 to 82 g m 30 sheets 22 to 28 Ib bond 83 to 105 g m 2 sheets 29 Ib bond to 80 Ib cover 106 to 220 g m 11 x 17 LGL and LTRR 30 sheets 18 to 22 Ib bond 64 to 82 g m 20 sheets 22 to 28 Ib bond 83 to 105 g m 2 sheets 29 Ib bond to 80 Ib cover 106 to 220 g m Power Source Maximum Power From the main unit Approximately 84 W Consumption Dimensions H x W x D 43 1 4 x 26 1 2 x 25 1 2 1 097 mm x 673 mm x 647 mm when the auxiliary tray is extended Installation Space Including the 62 1 8 x 26 3 4 1 577 mm x 680 mm Main Unit W x D when the multi purpose tray and the auxiliary tray are extended Booklet Finisher M1 Po ttem Specifications O O O O Paper Size Weight Type Size 12 x 18 12 5 8 x 17 11 16 11 x 17 LGL LTR LTRR STMT STMTR EXEC Custom size 3 7 8 x 5 1 2 to 12 5 8 x 18 99 mm x 139 7 mm to 320 mm x 457 2 mm and Envelopes Weight 17 lb bon
7. 3 27 to 28 lb bond 100 to 105 g m Recycled Color Pre Punched Bond Heavy 1 29 to 32 Ib bond 106 to 120 g m Heavy 2 33 Ib bond to 60 Ib cover 121 to 163 g m Heavy 3 61 to 80 Ib cover 164 to 220 g m Tracing Coated Labels Transparency and Envelopes If an envelope is loaded vertically it cannot be output from the Staple Finisher M1 Capacity Per Tray Upper Tray No finishing set Collate Group mode LTR STMTR and EXEC 1 300 sheets or 7 3 8 188 mm in height 12 x 18 11 x 17 LGL and LTRR 650 sheets or 3 3 4 96 mm in height Collate Offset Group Offset mode LTR and EXEC 1 300 sheets or 7 3 8 188 mm in height 11 x 17 LGL and LTRR 650 sheets or 3 3 4 96 mm in height Staple mode LTR and EXEC 1 300 sheets 30 sets or 7 3 8 188 mm in height 11 x 17 LGL and LTRR 650 sheets 30 sets or 3 3 4 96 mm in height No finishing set Collate Group mode with different paper sizes 650 sheets or 3 3 4 96 mm in height Staple mode with different paper sizes 650 sheets 30 sets or 3 3 4 96 mm in height Capacity Per Tray Lower Tray No finishing set Collate Group mode LTR STMTR and EXEC 1 700 sheets or 9 5 8 243 mm in height 12 x 18 11 x 17 LGL and LTRR 650 sheets or 3 3 4 96 mm in height Collate Offset Group Offset mode LTR and EXEC 1 700 sheets or 9 5 8 243 mm in height 11 x 17 LGL and LTRR 650 sheets or 3 3 4 96 mm
8. A de la NMB 003 du Canada 14 Super G3 is a phrase used to describe the new generation of fax machines that use ITU T V 34 standard 33 6 Kbps SUPER modems Super G3 High Speed Fax machines allow transmission times of approximately 3 seconds per page wo which results in reduced telephone line charges FEP G 3 Approximately 3 seconds per page fax transmission time based on CCITT ITU T No 1 Chart JBIG Pa FACSIMILE Standard Mode at 33 6 Kops modem speed The PSTN Public Switched Telephone Network currently supports 28 8 Kops modem speeds or slower depending on telephone line conditions NOTE The fax function is available only ifthe FAX Board is installed 15 A Important Safety Instructions Please read these Important Safety Instructions thoroughly before operating the machine As these instructions are intended to prevent injury to the user or other persons or destruction of property always pay attention to these instructions Also since it may result in unexpected accidents or injuries do not perform any operation unless otherwise specified in the manual Improper operation or use of this machine could result in personal injury and or damage requiring extensive repair that may not be covered under your Limited Warranty Installation 16 WARNING e Never block the ventilation slots and louvers on the machine These openings are provided for proper ventilation of working par
9. Canon USA www usa canon com or Canon Canada www canon ca These materials include a Technology White Paper for the CDS Service Your instruction to Canon USA Canon Canada or your dealer to use CDS Service or your use of CDS Service for a Product shall be considered i a representation that you have an internal IP network and internet access available to Products connected to that network on a generally continuous basis ii a representation that you have an internet connection and internal network bandwidth available for the Canon Server to download files to each of the Products receiving the CDS Service Downloaded files may vary in size some will be on the order of several hundred MB The CDS Service Technology White Paper contains further details iii authorization by you for the Canon Seller to establish and perform during the period of provision of Service HTTPS HTTP communications using your internet and internal network bandwidth for transmissions to and from the CDS Server iv authorization by you for the Product itself or a Canon serviceperson to download or update firmware and purchased MEAP application software data for internet based activation of optional Product features and certain related data files to Product from the CDS Server and to transmit service data e g serial number information of firmware of Product to the CDS Server You acknowledge and agree that the Canon Seller and CDS Server may rely on internet address
10. Color Pre Punched Bond Heavy 1 29 to 32 Ib bond 106 to 120 g m Heavy 2 33 Ib bond to 60 Ib cover 121 to 163 g m Heavy 3 61 to 80 Ib cover 164 to 220 g m Tracing Coated Labels Transparency and Envelopes Capacity Per Tray Tray A LTR STMT and Envelopes 250 sheets 21 Ib bond 80 g m STMTR 150 sheets 21 Ib bond 80 g m 12 x 18 12 5 8 x 17 11 16 11 x 17 LGL LTRR STMTR EXEC and Custom size 3 7 8 x 5 1 2 to 12 5 8 x 18 99 mm x 139 7 mm to 320 mm x 457 2 mm 100 sheets 21 Ib bond 80 g m Tray B 12 x 18 12 5 8 x 17 11 16 11 x 17 LGL LTR LTRR STMT STMTR EXEC Custom size 3 7 8 x 5 1 2 to 12 5 8 x 18 99 mm x 139 7 mm to 320 mm x 457 2 mm and Envelopes 100 sheets 21 Ib bond 80 g m Ifan envelope is loaded vertically it cannot be output from Tray B Dimensions H x W x D 3 x 16 3 4 x 16 76 mm x 426 mm x 407 mm Weight Approximately 1 Ib 574 g Installation Space Including the 33 3 8 x 26 3 4 846 mm x 680 mm Main Unit when the multi purpose tray and the auxiliary tray are extended 44 em Specifications Paper Size Weight Type Size 11 x 17 LGL LTR LTRR STMTR and EXEC Weight 17 lb bond to 32 Ib cover 64 to 120 g m Type Thin Plain 1 18 to 22 Ib bond 65 to 82 g m Plain 2 22 to 26 Ib bond 83 to 99 g m Plain 3 27 to 28 lb bond 100 to 105 g m Recycled Color Pre Punched Bond and Heavy 1 29 to 32 Ib bond 106 t
11. OF THIS THIRD PARTY SOFTWARE GOVERN THE THIRD PARTY SOFTWARE AS DELIVERED WITH THE PRODUCT AND ALL UPDATED VERSIONS OF THE THIRD PARTY SOFTWARE PROVIDED UNDER MAINTENANCE AGREEMENTS OR OTHER SERVICE ARRANGEMENTS FOR THE PRODUCT WITH CANON USA OR CANON CANADA OR THEIR RESPECTIVE AUTHORIZED SERVICE ORGANIZATIONS Please refer to the e Manual on a CD ROM bundled with this product for more detail and corresponding license conditions If you need source code of certain Software under respective Licenses used for this PRODUCT please send your request by email in English or Japanese at lt oipossg canon co jp gt The request must identify the names of Software and the applicable License Please refer to the e Manual on a CD ROM bundled with this product for more detail and corresponding license conditions The information in this document is subject to change without notice CANON INC MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL EITHER EXPRESS OR IMPLIED EXCEPT AS PROVIDED HEREIN INCLUDING WITHOUT LIMITATION THEREOF WARRANTIES AS TO MARKETABILITY MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR USE OR NON INFRINGEMENT CANON INC SHALL NOT BE LIABLE FOR ANY DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE OR LOSSES OR EXPENSES RESULTING FROM THE USE OF THIS MATERIAL The following applies in California USA only The battery included with your product contains Perchlorate Material and may require special handl
12. Point 100 x 100 dpi 150 x 150 dpi 200 x 100 dpi 200 x 200 dpi 200 x 400 dpi 300 x 300 dpi 400 x 400 dpi 600 x 600 dpi System Environment Windows 2000 Server SP4 Windows XP Professional SP3 Windows Server 2003 R2 SP2 Windows Vista SP2 Windows Server 2008 SP2 Windows Server 2008 R2 SP2 Windows 7 Solaris 10 Mac OS X 10 4 x 10 5 x 10 6 x Red Hat Linux 9 1000BASE T 100BASE TX 10BASE T Color Mode Automatic Color Select Full Color Grayscale Automatic Color Select Full Color Black and White Full Color Grayscale Black and White Optional PDF XPS OOXML Compact Trace and Smooth Encryption OCR Device Signature User Signature Functions Optimization for Web PDF A 1b Reader Extensions Policy Applied 1 PDF files optimized for Web viewing 46 E Mail and l Fax Features Specifications Communication Protocol SMTP POP3 Fax Communication Mode Simple Full Resolution For Sending E mail 100 x 100 dpi 150 x 150 dpi 200 x 100 dpi 200 x 200 dpi 200 x 400 dpi 300 x 300 dpi 400 x 400 dpi 600 x 600 dpi For Sending Fax 200 x 100 dpi 200 x 200 dpi 200 x 400 dpi 300 x 300 dpi 400 x 400 dpi 600 x 600 Black and White dpi ite For Sending l Fax 100 x 100 dpi 200 x 200 dpi 300 x 300 dpi 400 x 400 dpi 600 x 600 dpi Color Format TIFF JPEG PDF XPS OOXML Power Point I Fax TIFF MH MR MMR Black and White I Fax Color TIFF Profile C Original Size 11 x 17
13. envelopes 10 Paper Drawer s Upper Right Cover Open this cover when clearing a paper jam inside the main unit D Paper Drawer 2 Holds up to 550 sheets of paper 21 Ib bond 80 g m 12 Paper Drawer 1 Holds up to 520 sheets of paper 21 Ib bond 80 g m Main Power Switch Press to the I side to turn the power ON 14 Waste Toner Container Waste toner accumulates here ue 2 Use this port to connect the Super G3 2nd Line Fax Board to the machine Oune Use this port to connect a fax line to the machine 31 This section contains an external view of the imageRUNNER ADVANCE C2230 When the Cassette Feeding Unit AF1 Inner Finisher F1 Inner Finisher Additional Tray A1 and Copy Tray J1 Are Attached 1 Platen Glass O Toner Replacement Cover Use the platen glass when scanning books thick originals thin Open this cover to replace the toner cartridge originals transparencies etc O Toner Cartridge 2 Upper Cover of the Fixing Unit When toner runs out pull out the toner cartridge and replace it Open this cover to clear a paper jam in the fixing unit with a new one Duplexing Unit Pull out the duplexing unit to clear a paper jam 32 PE De CE lt X SS 1 Feeder Cover Open this cover to remove jammed paper O Slide Guides Adjust these guides to match the width of the original Original Supply Tray Originals placed here are automatically fed
14. job in progress such as a scan copy or fax scanning only job O Edit Pen Use when operating the touch panel display such as to enter characters 9 Start key Press to start an operation O Main Power Indicator Lights when the main power is turned ON 34 D Error Indicator Flashes or lights if there is an error in the machine When the Error indicator flashes follow the instructions that appear on the touch panel display When the Error indicator maintains a steady red light contact your local authorized Canon dealer 12 Processing Data Indicator Flashes or blinks green when the machine is performing operations and maintains a steady green light when fax data is stored in memory Clear key Press to clear entered values or characters Reset key Press to restore the standard settings of the machine ID Log In Out key Press to log in out when a login service such as Department ID Management or SSO H has been set Brightness Adjustment Dial Use to adjust the brightness of the touch panel display volume Settings key Press to display the screen for adjusting settings such as the transmission volume and fax sending receiving alarm volume 18 Status Monitor Cancel Press to check the status of jobs or to cancel print jobs Also you can check the status of the machine such as the amount of paper remaining in the paper source Quick Menu Press to display functions
15. jobs being processed or a MEAP application is running while the machine is shutting down Turn OFF the main power 1 Open the main power switch cover 2 Press the main power switch to the O side 3 Close the main power switch cover IMPORTANT Do not turn the main power OFF while using the Fax I Fax function Sending or receiving l fax or fax documents cannot be done when the main power is turned OFF The machine may take some time to completely shutdown Do not unplug the power cord until the main power indicator of the machine is OFF If the main power is turned OFF during scanning or printing a paper jam may occur lt NOTE You can shut down the machine from the Remote UI using the Remote Shutdown mode For more information see e Manual gt Remote UI If you set Quick Startup Settings for Main Power to On in Preferences Settings Registration the tone sounds when turning OFF the main power of the machine Depending on the situations the machine does not startup quickly and the tone does not sound 36 k Specifications Specifications are subject to change without notice for product improvement or future release Main Unit item O Specifications Canon imageRUNNER ADVANCE C2230 C2225 Available Paper Paper Drawers Weight Paper Drawer 1 17 to 32 Ib bond 64 to 120 g m Paper Drawer 2 17 Ib bond to 60 Ib cover 64 to 163 g m Type Paper Drawer 1 Thin Plain 1 18 to
16. or 1 3 4 44 mm in height when the Inner Finisher Additional Tray A1 is attached Collate Offset Group Offset mode LTR 750 sheets or 3 3 4 94 mm in height when the Inner Finisher Additional Tray A1 is not attached 350 sheets or 1 3 4 44 mm in height when the Inner Finisher Additional Tray A1 is attached 11 x 17 LGL and LTRR 500 sheets or 2 1 2 62 5 mm in height when the Inner Finisher Additional Tray A1 is not attached 350 sheets or 1 3 4 44 mm in height when the Inner Finisher Additional Tray A1 is attached Staple mode LTR 30 sets or 3 3 4 94 mm in height 11 x 17 LGL and LTRR 30 sets or 1 3 4 44 mm in height No finishing set Collate Group mode with different paper sizes 350 sheets or 1 3 4 44 mm in height Staple mode with different paper sizes 30 sets or 1 3 4 44 mm in height Capacity Per Tray Inner Finisher No finishing set Collate Group Collate Offset Group Offset mode Additional Tray A1 12 x 18 12 5 8 x 17 11 16 11 x 17 LGL LTR LTRR STMT STMTR and EXEC 100 sheets or 1 2 12 5 mm in height Staple mode 11 x 17 LGL LTR and LTRR 15 sets or 3 8 8 1 mm in height No finishing set Collate Group mode with different paper sizes 100 sheets or 1 2 12 5 mm in height Staple mode with different paper sizes 15 sets or 3 8 8 1 mm in height 43 tem Specifications O Max Stapling Capacity A
17. part of the tray where stapling is performed near the rollers when a finisher is attached as this may result in personal injury Staple Finisher M1 Inner Finisher F1 Booklet Finisher M1 18 Do not insert your hand into the machine while the paper drawer is removed as this may result in personal injury The laser beam can be harmful to human bodies Since radiation emitted inside the product is completely confined within protective housings and external covers the laser beam cannot escape from the machine during any phase of user operation Read the following remarks and instructions for safety Never open covers other than those instructed in the manuals for this machine Do not remove the following caution label which is attached to the machine If the label has been removed contact your local authorized Canon dealer t DANGER CAUTION 545 22 imsite Lasen sapino men open ano INTERLDGRS DEFEATED VOD POSURE TO THE DEN ATTENTION Sesenruse ou conaays te conTacT DE secte Rennes 2ERRTS EDS AIN VUNPIET EST DEENOUILE EVE LERPOSITON AU FASCEAU Gai TA VORSICHT sn Eee PRECAUCI N ME VARNING SEE as mage mue VAROITUS A AT TE F i Nu T DANGER Wists laser adaton nhen open nd ect detested VORSICHT SEX en Sue MOT DEN RAR ASETZEN urramenun AAATRAWANNAN apace CAUTION S255 meme ssamounon men crane PRECAUCI N RME se re AAN ER ES KLASS 38 OSYNLIG LASERSTRALNING NAR DENNA DEL AR PP
18. printing can adversely affect the operation of such equipment Avoid installing the machine near televisions radios or similar electronic equipment The machine might interfere with sound and picture signal reception Insert the power plug into a dedicated power outlet and maintain as much space as possible between the machine and other electronic equipment Contact an authorized Canon dealer if communication is unavailable Depending on your locale or your telephone connection you may be unable to perform data communication In this case contact your local authorized Canon dealer Do not remove the machine s leveling feet Do not remove the machine s leveling feet after the machine has been installed If you put weight on the front of the machine while the drawers or units within the machine are pulled out the machine may fall forward To prevent this from happening make sure that the machine s leveling feet are in place 24 Select a Safe Power Supply Plug the machine into a 120 V AC outlet Make sure that the power supply for the machine is safe and has a steady voltage Do not connect other electrical equipment to the same power outlet to which the machine is connected Do not connect the power cord to a multiplug power strip as this may cause a fire or electrical shock The power cord may become damaged if it is stepped on affixed with staples or if heavy objects are placed on it
19. publication may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying and recording or by any information storage or retrieval system without the prior written permission of Canon Inc This product includes software and or software modules that are licensed by Canon Inc or its licensors from third parties Use and distribution of this software and or software modules are subject to conditions a through c below a UFST Copyright 1989 1996 1997 2003 2004 2008 all rights reserved by Monotype Imaging Inc b Copyright Unpublished Work of Novell Inc All Rights Reserved c Portions of this software are copyright 2007 The FreeType Project www freetype org All rights reserved This Canon product the PRODUCT includes third party software modules Use and distribution of these software modules the SOFTWARE are subject to the conditions below 1 You agree that you will comply with any applicable export control laws restrictions or regulations of the countries involved in the event that this product including the SOFTWARE is shipped transferred or exported into any country 2 Rights holders of the SOFTWARE retain in all respects the title ownership and intellectual property rights in and to the SOFTWARE Except as expressly provided herein no license or right expressed or implied is hereby conveyed or granted by rights holders of the SOFTWARE to you for any in
20. rr err err ere eee eT ee ee ee ee ee Preface Thank you for purchasing the Canon imageRUNNER ADVANCE C2230 C2225 Please read this manual thoroughly before operating the machine to familiarize yourself with its capabilities and to make the most of its many functions For information on the detailed settings for the functions described in this manual see the e Manual After reading this manual store it in a safe place for future reference How To Use This Manual Symbols Used in This Manual The following symbols are used in this manual to explain procedures restrictions handling precautions and instructions that should be observed for safety Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly To use the machine safely always pay attention to these warnings Indicates a caution concerning operations that may lead to injury to persons if not performed correctly To use the machine safely always pay attention to these cautions Indicates operational requirements and restrictions Be sure to read these items carefully to operate the machine correctly and avoid damage to the machine or property Indicates a clarification of an operation or contains additional explanations for a procedure Reading these notes is highly recommended Indicates an operation that must not be performed Read these items carefully and make sure not to perform the described operations Th
21. slightly dampened cloth with a mild detergent mixed with water Do not use alcohol benzene paint thinner or other flammable substances Check detergent for flammability prior to use If flammable substances come into contact with a high voltage area inside the machine it may result in a fire or electrical shock There are some areas inside the machine which are subject to high voltages When removing jammed paper or when inspecting the inside of the machine do not allow necklaces bracelets or other metal objects to touch the inside of the machine as this may result in burns or electrical shock Do not burn or throw used toner cartridges into open flames as this may cause the toner remaining inside the cartridges to ignite resulting in burns or a fire Make sure that the power plug is firmly inserted into the power outlet after cleaning the machine Do not use the machine while the connection is loose as doing so may cause a fire Check the power cord and power plug regularly If the following conditions occur contact your local authorized Canon dealer as the condition may cause a fire e There are burn marks on the power plug The blade on the power plug is deformed or broken The power goes OFF and ON when the power cord is bent There are cuts cracks or indentations on the power cord A part of the power cord becomes hot Check the power cord and power plug regularly to make sure that they are not handled in the follow
22. the top bottom left and right edges of the paper With 12 5 8 x 17 11 16 size paper you cannot print in the areas 1 6 4 mm mm from the top and bottom edges of the paper and 1 4 7 5 mm mm from the left and right edges of the paper When printing in the 0 mode apart from 12 5 8 x 17 11 16 the upper margin becomes 1 6 4 mm the lower margin becomes 1 8 2 5 mm and the side margins both become 1 8 2 5 mm The printable area is enlarged When printing in the 0 mode 12 5 8 x 17 11 16 the upper margin becomes 1 6 4 mm the lower margin becomes 1 8 2 5 mm and the side margins both become 1 4 7 5 mm The printable area is enlarged 48 CANON imageRUNNER ADVANCE C2230 C2225 SERIES LIMITED WARRANTY Canon U S A Inc or Canon Canada Inc as applicable Canon warrants the imageRUNNER ADVANCE C2230 C2225 Series product and Canon brand options designed for use with the imageRUNNER product collectively the Product to be free from defects in workmanship and materials under normal use and service for a period of 90 days after delivery to the original purchaser Purchaser or 30 000 prints or copies or a combination of both whichever comes first During such warranty period Canon shall replace without charge any defective part with a new or comparable rebuilt part This warranty shall not extend to consumables such as paper chemicals and toner as to which there shall be no warranty or replacement Warran
23. tip over resulting in personal injury Power supply WARNING Do not damage or modify the power cord Also do not place heavy objects on the power cord or pull on or excessively bend it as this could cause electrical damage and result in a fire or electrical shock Keep the power cord away from a heat source failure to do this may cause the power cord coating to melt resulting in a fire or electrical shock Do not connect or disconnect the power cord with wet hands as this may result in electrical shock Do not connect the power cord to a multiplug power strip as this may cause a fire or electrical shock Do not bundle up or tie the power cord in a knot as this may result in a fire or electrical shock Insert the power plug completely into the power outlet as failure to do so may result in a fire or electrical shock Do not use power cords other than the power cord provided as this may result in a fire or electrical shock As a general rule do not use extension cords Using an extension cord may result in a fire or electrical shock Do not use power supplies with voltages other than those specified herein as this may result in a fire or electrical shock Always grasp the power plug when disconnecting the power cord Pulling on the power cord may expose or snap the core wire or otherwise damage the power cord If the power cord is damaged this could cause current to leak resulting in a fire or electr
24. when the auxiliary tray is extended Installation Space Including the 66 1 2 x 26 3 4 1 689 mm x 680 mm Main Unit W x D when the multi purpose tray and the auxiliary tray are extended 42 Inner Finisher F1 Item Specifications Paper Size Weight Type Size 12 x 18 12 5 8 x 17 11 16 11 x 17 LGL LTR LTRR STMT STMTR EXEC Custom size 3 7 8 x 5 1 2 to 12 5 8 x 18 99 mm x 139 7 mm to 320 mm x 457 2 mm and Envelopes Weight 17 lb bond to 80 Ib cover 64 to 220 g m Type Thin Plain 1 18 to 22 Ib bond 65 to 82 g m Plain 2 22 to 26 Ib bond 83 to 99 g m Plain 3 27 to 28 lb bond 100 to 105 g m Recycled Color Pre Punched Bond Heavy 1 29 to 32 Ib bond 106 to 120 g m Heavy 2 33 Ib bond to 60 Ib cover 121 to 163 g m Heavy 3 61 to 80 Ib cover 164 to 220 g m Tracing Coated Labels Transparency and Envelopes If an envelope is loaded vertically it cannot be output from the Inner Finisher F1 Capacity Per Tray Standard Tray No finishing set Collate Group mode LTR STMT STMTR and EXEC 750 sheets or 3 3 4 94 mm in height when the Inner Finisher Additional Tray A1 is not attached 350 sheets or 1 3 4 44 mm in height when thelnner Finisher Additional Tray A1 is attached 12 x 18 12 5 8 x 17 11 16 11 x 17 LGL and LTRR 500 sheets or 2 1 2 62 5 mm in height when the Inner Finisher Additional Tray A1 is not attached 350 sheets
25. 11 x 17 LGL 11 x 15 gt LTR 1 0 64 11 x 17 LTR 1 0 50 11 x 17 gt STMT 1 0 25 Enlargement 1 1 21 LGL gt 11 x 17 1 1 29 LTR gt 11 x 17 1 2 00 STMT gt 11 x 17 1 4 00 25 to 400 in 1 increment Paper Feeding System Capacity Paper Drawers Paper Drawer 1 640 sheets 17 Ib bond 64 g m 520 sheets 21 Ib bond 80 g m Paper Drawer 2 680 sheets 17 Ib bond 64 g m 550 sheets 21 Ib bond 80 g m Multi Purpose Tray 100 sheets 21 Ib bond 80 g m Multiple Copies 1 to 999 sheets Hard Disk Capacity 160GB Used space 80GB The hard disk capacity is subject to change in future release Power Consumption Maximum Power Consumption 1 5 kW When the machine is in the Sleep mode 0 8 W When the main power switch is turned OFF When Quick Startup Settings for Main Power is set to On 0 45 W When Quick Startup Settings for Main Power is set to Off 0 19 W Depending on the system and conditions of use these values may differ Dimensions H x W x D 36 1 2 x 22 1 4 x 26 3 4 928 mm x 565 mm x 680 mm Weight Approximately 198 Ib 90 kg Installation Space W x D 33 3 8 x 26 3 4 846 mm x 680 mm when the multi purpose tray is extended 38 Item O O Specifications Size and Weight of Originals Size 11 x 17 LGL LTR LTRR STMT and STMTR Weight 1 sided scanning 11 Ib bond to 34 Ib bond 42 to 128 g m 2 sided scanning 13 lb bond to 34 Ib bond
26. 22 Ib bond 65 to 82 g m Plain 2 22 to 26 Ib bond 83 to 99 g m Plain 3 27 to 28 lb bond 100 to 105 g m Recycled Color Pre Punched Bond and Heavy 1 29 to 32 Ib bond 106 to 120 g m Paper Drawer 2 Thin Plain 1 18 to 22 Ib bond 65 to 82 g m Plain 2 22 to 26 Ib bond 83 to 99 g m Plain 3 27 to 28 lb bond 100 to 105 g m Recycled Color Pre Punched Bond and Heavy 1 29 to 32 Ib bond 106 to 120 g m Heavy 2 33 Ib bond to 60 Ib cover 121 to 163 g m Transparency and Envelopes Multi Purpose Tray Weight 17 lb bond to 80 Ib cover 64 to 220 g m Type Thin Plain 1 18 to 22 Ib bond 65 to 82 g m Plain 2 22 to 26 Ib bond 83 to 99 g m Plain 3 27 to 28 lb bond 100 to 105 g m Recycled Color Pre Punched Bond Heavy 1 29 to 32 Ib bond 106 to 120 g m Heavy 2 33 Ib bond to 60 Ib cover 121 to 163 g m Heavy 3 61 to 80 Ib cover 164 to 220 g m Tracing Coated Labels Transparency and Envelopes Acceptable Originals Sheet book three dimensional objects up to 2 kg Paper Sizes Paper Drawer 1 11 x 17 LTR and EXEC Paper Drawer 2 12 x 18 11 x 17 LGL LTR LTRR STMTR EXEC Custom size 5 1 2 x 7 1 8 to 12 x 15 3 8 139 7 mm x 182 mm to 304 8 mm x 457 2 mm and Envelopes Multi Purpose Tray 12 x 18 12 5 8 x 17 11 16 11 x 17 LGL LTR LTRR STMTR STMT EXEC Custom size 3 7 8 x 5 1 2 to 12 5 8 x 18 99 mm x 139 7 mm to 320 mm
27. 4 96 mm in height Collate Offset Group Offset mode LTR and EXEC 1 700 sheets or 9 5 8 243 mm in height 11 x 17 LGL and LTRR 650 sheets or 3 3 4 96 mm in height Staple mode LTR and EXEC 1 700 sheets 30 sets or 9 5 8 243 mm in height 11 x 17 LGL and LTRR 650 sheets 30 sets or 3 3 4 96 mm in height No finishing set Collate Group mode with different paper sizes 650 sheets or 3 3 4 96 mm in height Staple mode with different paper sizes 650 sheets 30 sets or 3 3 4 96 mm in height Max Stapling Capacity Available Corner Staple Double Staple mode Staple Size LTR and EXEC 50 sheets 17 to 22 Ib bond 64 to 82 g m 30 sheets 22 to 28 Ib bond 83 to 105 g m 2 sheets 29 Ib bond to 80 Ib cover 106 to 220 g m 11 x 17 LGL and LTRR 30 sheets 17 to 22 lb bond 64 to 82 g m 20 sheets 22 to 28 Ib bond 83 to 105 g m 2 sheets 29 Ib bond to 80 Ib cover 106 to 220 g m Max Saddle Stitch Capacity Saddle Stitch Available Saddle Stitch Size 11 to 16 sheets 17 to 22 Ib bond 64 to 82 g m 6 to 10 sheets 22 to 28 Ib bond 83 to 105 g m 1 to 5 sheets 29 to 32 Ib bond 106 to 120 g m Saddle Folding 1 sheet 17 Ib bond to 80 Ib cover 64 to 209 g m Size 12 x 18 11 x 17 LGL and LTRR Power Source Maximum Power From the main unit Approximately 118 W Consumption Dimensions H x W x D 43 1 4 x 31 x 25 7 8 1 097 mm x 786 mm x 656 mm
28. Canon ImageRUNNER ADVANCE C2230 C2225 Before Using This Machine Read this guide first Please read this guide before operating this product After you finish reading this guide store it in a safe place for future reference ENG Manuals for the Machine The manuals for this machine are divided as follows Please refer to them for detailed information Guides with this symbol are printed manuals Guides with this symbol are included on the accompanying CD ROM Before Using This Machine This Manual e Describes precautions for using the machine e Includes the specifications of the machine Setup Guide Describes the settings required before using functions such as the network settings for sending e mail Describes how to add applications and update the firmware Basic Operation Guide Provides an overview of the functions and describes the basic operations Describes the maintenance and troubleshooting procedures for the machine Includes answers to frequently asked questions HTML manual Describes all the functions of the machine Also provided with a search function that is useful for finding and checking information Includes Practical Workflows which introduces flows of practical operations using functions of the machine Driver Installation Guide Provides instructions on installing the printer fax and other drivers Printer Driver Installation Guide Mac Printer Driver Install
29. LGL LTR LTRR STMT STMTR Fax 11 x 17 LGL LTR LTRR STMT STMTR Server Software Microsoft Exchange 2003 SP2 Microsoft Exchange 2007 SP2 Sendmail 8 14 4 Lotus Domino R7 0 Other Searches a destination via the LDAP Server Preview Optional PDF XPS OOXML PDF Compact Trace and Smooth Encryption OCR Device Signature User Signature Functions E mail only Optimization for Web PDF A 1b Reader Extensions Policy Applied Compact OCR Device Signature User Signature OOXML Power Point OCR 1 Available after setting RX conditions of the destination 2 Sent as LTR 3 PDF files optimized for Web viewing 47 Network Environment Hardware Specifications Network Interface 10Base T 100Base TX 1000Base T RJ 45 Software Specifications Protocol Supported TCP IP Frame type Ethernet Il Print applications LPD Raw IPP IPPS FTP WSD SMB IPX SPX Frame type Ethernet Il Ethernet 802 2 Ethernet 802 3 Ethernet SNAP Auto Detect Print applications Bindery PServer NDS PServer RPrinter NPrinter AppleTalk Frame type Ethernet SNAP Print application PAP Printer Access Protocol Printer Settings Software Specifications Command Language PCL5c PCL6 PostScript 3 Resident Fonts 93 Scalable fonts 2 OCR fonts and 10 Bitmap fonts 136 Scalable fonts Printable Area PCL5c PCL6 Reduced to 1 6 4 23 mm from the top bottom left and right edges of the paper PostScript 3 Reduced to 1 6 4 mm from
30. NAD EE 38 HA MOI BAM d c ATTENTION tiomeworucenassieoccusseseeveas VARNING SESS RAE AR ue Pme EST DEVEROUILE EvTez Lexpostion aU FAISCEAU VAROITUS SoLaluironser POISTEYTUNA VALTA ATOME SAYEELLE If the laser beam escapes from the machine exposure may cause serious damage to your eyes Controlling adjusting or operating the machine in ways not mentioned in the manuals for this machine may cause dangerous radiation to escape from the machine O IMPORTANT Press eenergy Saver for safety when the machine will not be used for a long period of time such as overnight Also turn OFF the main power switch and disconnect the power cord for safety when the machine will not be used for an extended period of time such as during consecutive holidays 19 Maintenance and Inspections 20 WARNING When cleaning the machine first turn OFF the main power switch then disconnect the power cord Failure to observe these steps may result in a fire or electrical shock Disconnect the power cord from the power outlet regularly and clean the area around the base of the power plug s metal pins and the power outlet with a dry cloth to ensure that all dust and grime is removed If the power cord is connected for a long period of time in a damp dusty or smoky location dust can build up around the power plug and become damp This may cause a short circuit and result in a fire Clean the machine using a
31. PORATION WITH RESPECT TO THE PRODUCT SHALL BIND CANON ANY SUPPLIER OR ANY AUTHORIZED SERVICE PROVIDER NO WARRANTY IS GIVEN ON ANY USED PRODUCT NEITHER CANON OR ITS SUPPLIERS NOR ANY AUTHORIZED SERVICE PROVIDER SHALL BE LIABLE FOR PERSONAL INJURY OR PROPERTY DAMAGE UNLESS CAUSED SOLELY AND DIRECTLY BY THE NEGLIGENCE OF CANON OR ANY AUTHORIZED SERVICE PROVIDER LOSS OF REVENUE OR PROFIT FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS EXPENDITURES FOR SUBSTITUTE EQUIPMENT OR SERVICES LOSS OR CORRUPTION OF DATA INCLUDING WITHOUT LIMITATION DATA STORED ON THE PRODUCT S HARD DISK DRIVE STORAGE CHARGES OR OTHER SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE MISUSE OR INABILITY TO USE THE PRODUCT REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED AND EVEN IF CANON OR ITS SUPPLIERS OR ANY AUTHORIZED SERVICE PROVIDER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES NOR SHALL RECOVERY OF ANY KIND AGAINST CANON OR ITS SUPPLIERS OR ANY AUTHORIZED SERVICE PROVIDER BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT CAUSING THE ALLEGED DAMAGE WITHOUT LIMITING THE FOREGOING THE PURCHASER ASSUMES ALL RISKS AND LIABILITY FOR LOSS DAMAGE OR INJURY TO PERSONS AND PROPERTY OF THE PURCHASER OR OTHERS ARISING OUT OF THE POSSESSION USE MISUSE OR INABILITY TO USE THE PRODUCT NOT CAUSED SOLELY AND DIRECTLY BY THE NEGLIGENCE OF CANON OR ANY AUTHORIZED SERVICE PROVIDER THIS WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL
32. PURCHASER OF THE PRODUCT AND STATES SUCH PURCHASER S EXCLUSIVE REMEDY CONDITIONS OF WARRANTY Defective parts must be returned to Canon or an Authorized Service Provider with all necessary documentation and will become the property of Canon THIS WARRANTY APPLIES TO PRODUCTS SOLD AND USED IN THE U S A AND CANADA ONLY 49 TERMS OF imageWARE REMOTE SERVICE If your Canon Office Imaging Product Product is enabled with embedded functions for the imageWARE Remote Diagnostic Service IWR or your Product is not IWR enabled but it interacts with the IWR Plug in program of imageWARE Enterprise Management Console EMC software then Canon USA Canon Canada or their respective authorized independent Canon retail dealers can access Product meter readings and receive notifications of certain service errors automatically via the internet You can read more about IWR in Canon published materials available from your dealer or on the web sites of Canon USA www usa canon com or Canon Canada www canon ca IWR will only collect and transmit Product specific meter readings and service data and will not access collect or transmit End User image data in the Product Your instruction to Canon USA Canon Canada or your dealer to activate IWR for a Product shall be considered i a representation that you have an internal IP network and internet access available on a generally continuous basis ii authorization by you to establish and perform durin
33. TENTION SNOMEMENT LASER INVISIBLE DE CLASSE 3B cas T D OUVERTURE OU LORSQUE LE CONTACT DE SECUNTE ETERS 1V90IRNITS EISAI IARVNET EST OEVEROULLE EVTEZ EXPOSITION AU FAISCEAU HB EEG ze02e VORSICHT insects usenet new ceonnactrner no SEM EMS Oth Ueno NNT D STAR SEE ON RADUCION LASER INVISIBLE DE CLASE 98 PRESENTE AL ABRIR Y CUANDO EST N PRECAUCI N jiaizibostos BLOGUES De Seau eve A og HU VARNING LASS 3P OSYNUO LASERSTRALING nin DENNA DEL R OPPAD Gok SPAARAR AR URKOPPLADE STALEN AR FARLIG LUOKAN 38 NAKYMATTOMALLE LASER S TEYA AVATTUNA JA VAROITUS SUGEKLURITUKSET POISTETTUA VALTA AGISTOMSTASATERLE DANGER iisti ase aatan nten operaram detse VORSICHT aa wo usta AASER APRA STON RRR RNA AIR ARAL BELAN SEAL AIR ZA 28 53 28 ei atom wo WRLC au ne eo N ance scan D us 39 PRESENTE AL ABAR Y CUANDO ESTAN CAUTION gas nmmeuse our en open ao PRECAUCI N Koss L08 BLOOS E este Ee LA os KLASS 8 OSYNLIG LASERSTRALAING NAR DENNA DEL R PPNAD ATTENTION Pouer usen pmapipecusseseveas VARNING 2 SEE HERA A EAEE D OUVERTURE OU LORSQUE Le DE SECURITE ras POLE LE CONTACT QE VAROITUS LUOKAN 28 NAKYMATTOMALLE LASER S TELYR AVATUNA JA CET RER AR ut Lo ant ak TERMS 2909 2ENRTSEDSAPTAL PRRNERT E ARAELSEDUCE SUOLALUKITUKSET POISTETTUINA VACTAALTISTUMISIA SATEELLE Use of controls adjustments or performance of procedures other than those specified in the manua
34. aint with the FCC if he she believes it is necessary WARNING The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone facsimile machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission the date and time it is sent and an identification of the business or other entity or other individual sending the message and the telephone number of the sending machine or such business other entity or individual The telephone number provided may not be a 900 number or any other number for which charges exceed local or long distance transmission charges lt NOTE To program this information into your machine complete the procedure for registering your name unit s telephone number time and date as described in Basic Operations or Settings Registration in the e Manual 12 Users in Canada Preinstallation Requirements for Canon Facsimile Equipment lt NOTE The fax function is available only if the FAX Board is installed A Location Supply a suitable table cabinet or desk for the machine See Specifications in this guide for specific dimensions and weight B Order Information 1 A single telephone line touch tone or rotary should be used If the Super G3 2nd Line Fax Board is installed a multi telephone line touch tone or rotary can be
35. ation Guide Fax Driver Installation Guide Network ScanGear Installation Guide Included on the same CD ROM as each driver To view the manual in PDF format Adobe Reader Acrobat Reader Acrobat is required If Adobe Reader Acrobat Reader Acrobat is not installed on your system please download it from the Adobe Systems Incorporated website http www adobe com Contents Preface CO CC oer ere ere ere LEE ELLE LEE LEE EEO EEE OE OEE ELE OE EE OEE EEE EEE EEE TE How To Use This Manual eccccccccccccccccccc ccc ccc ccc ccc cece ccc ccc ceeccceeccecceces Symbols Used in This Manual nono nono err err ere ere ere reer ee eee ee ee ee ee ee ee ee ee ee ee ee ee a Keys and Buttons Used in This Manual sseeeseseeseseseesocecoeoosocoococoooocoeoococoococoeoocoeoeoe 3 Illustrations Used in This Manual essences Abbreviations Used in This Manual soso Trademarks cesse soso cesses ees ee reese sees seesseseeseseseeeeseseeseeed Operations and Terms Used in This Manual ssseseeseeseseesesoesocsococoeoococoococoooocoeoococoocoeoeo 7 Legal Notices CeCe eee er eereerereeesereeeseeeeeseeeeeseLesereresereoeeeseoeserooesg Product NAME ce ccecccvcccccvccccvceccescecee reese reese sees ee sees esses seseeseeseesesesessseesee eg FCC Federal Communications Commission seseesesecsesescoosecoococooooeooooocoeooooocoosoeooooosoooeo o8 Laser Safety ARE EEE EE EEE EEE EEE EEE EEE ECC EEE EEE EEE EEE International ENERGY STAR Program sssssssssssosessesssssesss
36. contact the appropriate electric inspection authority or electrician as appropriate lt NOTE This equipment complies with the Canadian ICES 003 Class A limits 13 Utilisation au Canada Conditions Remplir Pr alablement L installation d un T l copieur Canon lt NOTE La fonction de Fax est disponible uniquement lorsqu une carte FAX est installee A Emplacement Pr voir une table un meuble ou un bureau suffisamment solide et de taille appropri e voir Sp cifications pour les indications de poids et dimensions B Installation t l phonique 1 Une seule ligne t l phonique tonalit s ou impulsions doit tre utilis e Si le Super G3 2nd Line Fax Board en option est install il est possible d utiliser une ligne t l phonique multiple tonalit s ou impulsions 2 Il faut commander un jack modulaire CA11A qui sera install par la compagnie t l phonique Sans ce jack la mise en place serait impossible 3 Si vous vous abonnez une nouvelle ligne demandez une ligne d affaires normale de qualit t l phonique courante ou quivalente Prenez un abonnement d une ligne par appareil Si le Super G3 2nd Line Fax Board en option est install il est possible d utiliser une ligne t l phonique multiple Ligne automatique interurbaine ou Ligne automatique international si vous communiquez avec les pays trangers lt NOTE Canon vous conseille d utiliser une ligne individuelle conforme aux normes
37. contains the Universal Font Scaling Technology or UFST under license from Monotype Imaging Inc UFST is a trademark of Monotype Imaging Inc registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions Apple AppleTalk EtherTalk LocalTalk Mac Macintosh Mac OS and Safari are trademarks of Apple Inc registered in the U S and other countries Microsoft Windows Windows Vista Windows Server Internet Explorer Excel and PowerPoint are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Adobe PostScript 3 Adobe PostScript and the PostScript logo are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries Copyright 2007 08 Adobe Systems Incorporated All rights reserved Protected by U S Patents 5 737 599 5 781 785 5 819 301 5 929 866 5 943 063 6 073 148 6 515 763 6 639 593 6 754 382 7 046 403 7 213 269 7 242 415 Patents pending in the U S and other countries All instances of the name PostScript in the text are references to the PostScript language as defined by Adobe Systems Incorporated unless otherwise stated The name PostScript also is used as a product trademark for Adobe Systems implementation of the PostScript language interpreter Except as otherwise stated any reference to a PostScript printing device PostScript display device
38. d to 80 Ib cover 64 to 220 g m Type Thin Plain 1 18 to 22 Ib bond 65 to 82 g m Plain 2 22 to 26 Ib bond 83 to 99 g m Plain 3 27 to 28 lb bond 100 to 105 g m Recycled Color Pre Punched Bond Heavy 1 29 to 32 Ib bond 106 to 120 g mi Heavy 2 33 Ib bond to 60 Ib cover 121 to 163 g m Heavy 3 61 to 80 Ib cover 164 to 220 g m Tracing Coated Labels Transparency and Envelopes Ifan envelope is loaded vertically it cannot be output from the Booklet Finisher M1 Capacity Per Tray Upper Tray No finishing set Collate Group mode LTR STMTR and EXEC 1 300 sheets or 7 3 8 188 mm in height 12 x 18 11 x 17 LGL and LTRR 650 sheets or 3 3 4 96 mm in height Collate Offset Group Offset mode LTR and EXEC 1 300 sheets or 7 3 8 188 mm in height 11 x 17 LGL and LTRR 650 sheets or 3 3 4 96 mm in height Staple mode LTR and EXEC 1 300 sheets 30 sets or 7 3 8 188 mm in height 11 x 17 LGL and LTRR 650 sheets 30 sets or 3 3 4 96 mm in height No finishing set Collate Group mode with different paper sizes 650 sheets or 3 3 4 96 mm in height Staple mode with different paper sizes 650 sheets 30 sets or 3 3 4 96 mm in height 41 tem Specifications S O Capacity Per Tray Lower Tray No finishing set Collate Group mode LTR STMTR and EXEC 1 700 sheets or 9 5 8 243 mm in height 12 x 18 11 x 17 LGL and LTRR 650 sheets or 3 3
39. dealers shall be responsible for alleged deficiencies in or your dissatisfaction with IWR or any software used to provide IWR A copy of the limited warranty statement can be found within this Operator s Manual If your dealer ceases to be an authorized Canon USA dealer it will no longer have access to the use and service data accumulated by IWR for your Product In that case you may request or instruct Canon USA to recommend to you an alternative service provider who will have access to this data in order to maintain Product service utilizing IWR functionality 50 TERMS OF Content Delivery System If the Content Delivery System CDS Service is enabled for your Canon Office Imaging Product Product Canon USA Canon Canada or their respective authorized independent Canon retail dealers each a Canon Seller can arrange internet based downloads for purposes of updating firmware delivering purchased MEAP application software and activation of optional Product features Certain related data files also may be downloaded e g End User License Agreements conditions of export Release Notes to your Product The internet communications will occur between the Product and one or more servers managed by Canon Inc Canon Server CDS Service will not download the firmware software or data files for purposes other than mentioned above You can read more about CDS Service in Canon published materials available from your dealer or on the web sites of
40. dges into a bag to prevent the toner remaining inside the cartridges from scattering and dispose of them in a location away from open flames 2 a When using telephone equipment incorporated into this machine basic safety precautions should always be followed to reduce the risk of fire electrical shock or injury to persons including the following 1 Do not use this machine where there is a potential for contact with water or other liquid 2 Do not use the telephone equipment during an electrical storm as there may be a remote risk of electrical shock from lightning 3 Do not use the telephone equipment to report a gas leak in the vicinity of the leak 2 a For cardiac pacemaker users This product emits low level magnetic flux If you use a cardiac pacemaker and feel abnormalities please move away from the product and consult your doctor N 2 im Installation Location and Handling This section describes precautions for installation location and handling We recommend that you read this section prior to using this machine Avoid Installing the Machine in the Following Locations Avoid locations subject to temperature and Avoid poorly ventilated locations humidity extremes whether low or high This machine generates a slight amount of ozone etc during For example avoid installing the machine near water faucets hot normal use Although sensitivity to ozone etc may vary this water heaters humidifier
41. dimensions and weight B Order Information 1 A single telephone line touch tone or rotary should be used If the Super G3 2nd Line Fax Board is installed a multi telephone line touch tone or rotary can be used 2 Order an RJ11 C telephone wall jack USOC which should be installed by the telephone company If the RJ11 C wall jack is not present telephone facsimile operation is not possible 3 Order a normal business line from your telephone company s business representative The line should be a regular voice grade line or an equivalent one Use one line per unit If the Super G3 2nd Line Fax Board is installed you can use a multi line DDD Direct Distance Dial line or IDDD International Direct Distance Dial line if you communicate overseas amp NOTE Canon recommends an individual line following industry standards i e 2500 touch tone or 500 rotary pulse dial telephones A dedicated extension off a PBX Private Branch eXchange unit without Call Waiting can be used with your facsimile unit Key telephone systems are not recommended because they send nonstandard signals to individual telephones for ringing and special codes which may cause a facsimile error C Power Requirements The machine should be connected to a standard 120 volt AC three wire grounded outlet only Do not connect this machine to an outlet or power line shared with other appliances that cause electrical noise Air conditioners electr
42. doctor immediately 21 2 a Do not burn or throw used toner cartridges into open flames as this may cause the toner remaining inside the cartridges to ignite resulting in burns or a fire Do not store toner cartridges or copy paper in places exposed to open flames as this may cause the toner or paper to ignite resulting in burns or a fire If you accidentally spill or scatter toner carefully gather the toner particles together or wipe them up with a soft damp cloth in a way that prevents inhalation Never use a vacuum cleaner that does not have safeguards against dust explosions to clean up spilled toner Doing so may cause a malfunction in the vacuum cleaner or result in a dust explosion due to static discharge a gt zZ Keep toner and other consumables out of the reach of small children If these items are ingested consult a physician immediately Do not dismantle the toner cartridge as doing so may cause toner to fly out and enter your eyes or mouth If toner gets into your eyes or mouth wash them immediately with cold water and immediately consult a physician If toner escapes from the toner cartridge make sure not to ingest the toner or allow it to directly touch your skin If toner touches your skin wash it away with soap and water If your skin still feels irritated after washing it or you ingest toner consult a doctor immediately When discarding used toner cartridges put the cartri
43. ds or flammable substances alcohol benzene paint thinner etc inside the machine If these items come into contact with a high voltage area inside the machine it may result in a fire or electrical shock If these items are dropped or spilled inside the machine immediately turn OFF the main power switch and disconnect the power cord from the power outlet Then contact your local authorized Canon dealer Do not use the product for uses other than as a color digital multitasking machine Do not place heavy objects on the machine as they may tip over or fall resulting in personal injury e Close the feeder gently to avoid catching your hands as this may result in personal injury Do not press down hard on the feeder when using the platen glass to make copies of thick books Doing so may damage the platen glass and result in personal injury Do not touch the finisher while the machine is printing as this may result in personal injury e Paper that has just been output from the machine may be hot Be careful when removing or aligning paper from the output tray Touching paper right after it is output may result in low temperature burns Do not place your hands hair clothing etc near the exit and feed rollers Even if the machine is not in operation your hands hair or clothing may get caught in the rollers which may result in personal injury or damage if the machine suddenly starts printing Do not place your hands in the
44. e following symbols and key button names are a few examples of how keys and buttons to be clicked or pressed are expressed in this manual Touch Panel Display Keys Key Name Example Cancel Close Control Panel Keys Key Icon Key Name Example Start L Stop Buttons on Computer Operation Screens Button Name Example OK Add Illustrations used in this manual are those displayed when the imageRUNNER ADVANCE C2230 has the following optional equipment attached toit Inner Finisher F1 Inner Finisher Additional Tray A1 Cassette Feeding Unit AF1 Copy Tray J1 In this manual product names and model names are abbreviated as follows Microsoft Windows 2000 operating system Windows 2000 Microsoft Windows Server 2003 operating system Windows Server 2003 Microsoft Windows Server 2003 R2 operating system Windows Server 2003 R2 Microsoft Windows XP operating system Windows XP Microsoft Windows Vista operating system Windows Vista Microsoft Windows Server 2008 operating system Windows Server 2008 Microsoft Windows Server 2008 R2 operating system Windows Server 2008 R2 Microsoft Windows 7 operating system Windows 7 Microsoft Windows operating system Windows Microsoft Internet Explorer Internet Explorer Microsoft Windows Internet Explorer Internet Explorer Novell NetWare NetWare Apple Macintosh Macintosh Apple Mac Mac MEAP and the MEAP logo are trademarks of Canon Inc This product
45. es you assign to Products and that using the internet has benefits but also certain risks ACCORDINGLY YOU AGREE THAT THE CDS SERVICE IS PROVIDED WITHOUT WARRANTY OF ANY KIND THAT ANY WARRANTIES ARE DISCLAIMED AND THAT NO CANON SELLER OR CANON AFFILIATE IS RESPONSIBLE FOR ANY INJURY TO YOUR NETWORK OR TO DATA OR DEVICES NOT SUPPLIED BY A CANON SELLER You will be responsible for network security and any data back up You will timely advise the Canon Seller of any security procedures the Canon Seller will need to use to provide CDS Services as described herein To the extent downloads involve presenting end user license terms on your network or network connected Products with a Canon Seller Canon affiliate or a third party as licensor seeking agreement to such terms any party that you allow to respond to presented license terms will be and is authorized by you to agree or not agree to the terms if license terms are not agreed a license purchased will not be enabled and you may apply for refund of any license fees paid You acknowledge and agree that the firmware provided by the CDS Service is governed by the Third Party Software terms set forth in this manual 51 52 Canon CANON INC 30 2 Shimomaruko 3 chome Ohta ku Tokyo 146 8501 Japan CANON U S A INC One Canon Plaza Lake Success NY 11042 U S A CANON CANADA INC 6390 Dixie Road Mississauga Ontario LST 1P7 Canada CANON EUROPA N V Bovenkerkerweg 59 61 1185 XB Am
46. esee x When the Cassette Feeding Unit AF1 Inner Finisher F1 Inner Finisher Additional Tray A1 and Copy Tray J1 Are Attached occccccccccccccccccccccsceccerce cee eee sees esse see see seeeeseeseeseeseeeeesseeeseeseeex Internal View ccccccccvcccccccc cece cece reece reece reer sere esses ees ereesseseeseeseseeseeeessseseesy When the Cassette Feeding Unit AF1 Inner Finisher F1 Inner Finisher Additional Tray A1 and Copy Tray J1 Are Attached MERE ee ee ee er er e32 eeder MORENO OO denis UCR ETE EE COU CE see sise E3 Control Panel Parts and FUNCtIONS eccccccccccccccvecccvceccescecceceeceseeceeseeceeceeceeeesessee eth Main Power and Energy Saver Key eee eee eee eee eee eee eee ee ee ee ee ee ee ey How to Turn ON the Main Power ececcccccccccccccccccccccccceccecec cece see seeseeceeceeeeeeeseesee sy Energy Saver Keyssseeccecccccccccccccccccccscccccscccsccssccsccscrscscscsssessessessssssessees sesh Shutting Down the Machine esssssssssssssssessssessssssesssssesssssesssssesssesesesesesessesess 036 Specifications eerceccccccccccccvccvecceccvccccccvcccvesseccscssecccecesesvecesees Main Unites sccccccccccccccccccccvcccccccccccccssceeseeec esses eseesseeesesscesscsesessscescceseeers Feeder essences eee e reese sees eeeesseseeseeseeseseseseseesee 3G Cassette Feeding Unit AFleeeeeeeeeecececccoccceeccccccoccccccoccceeccccccocceecccoceceecccccceeeee 39 Envelope Feeder Attachment D1e essences e39 Staple Finisher M1 nono nono ns ssssssssessos
47. g production runs especially in poorly ventilated rooms It is recommended that the room be appropriately ventilated sufficient to maintain a comfortable working environment in areas of machine operation For safety reasons Press Energy Saver when it will not be used for a long period of time such as overnight As an added safety measure turn OFF the main power switch and disconnect the power cord when the machine will not be used for an extended period of time such as during consecutive holidays Use a modular cable that is shorter than 9 10 3 meters Use a USB cable that is shorter than 9 10 3 meters Backing Up Exporting Data Various data such as the received data address book and Settings Registration settings are stored on the internal memory of the machine A malfunction in the memory may cause these data to be lost Please regularly back up export your important data Please note that Canon will not be held responsible for any damages caused by the loss of data You can backup export data in the following ways Import Export All e Import Export Individually You can back up export the following data Data You Can Import Export All You can save load multiple items at once In addition you can exchange data with this machine and other machines which support the Import Export All function O IMPORTANT 28 You cannot use the Import All function depending on the recipient s mach
48. g the period of IWR activation HTTPS communications using your network bandwidth for transmissions over the internet of use and service data accumulated by the Product and iii authorization by you to store analyze and use this data for purposes related to servicing the Product and for Product and IWR improvement By so instructing Canon USA Canon Canada or your dealer you shall also be considered to acknowledge that A the IWR software embedded or plug in is the confidential property of Canon USA and its licensor B you have no rights in such IWR software except as the Product executes the limited data collection and transmission functions for which it is configured when delivered and you obtain the benefits of IWR as outlined in Canon published materials C you shall not disassemble decompile reverse engineer disclose or attempt to copy such IWR software allow any third party to do any of the foregoing or transfer your limited rights to any other party without the prior written approval of Canon USA or Canon Canada and D there are many factors outside of the control of Canon USA Canon Canada or their respective dealers that could affect the accuracy or timing of meter readings or service data harvested by IWR and except as expressly provided in the limited warranty statement for the Product or the End User License Agreement for EMC software in the case of the IWR Plug in program neither Canon USA Canon Canada nor their respective
49. ic typewriters copiers and machines of this sort generate electrical noise that often interferes with communications equipment and the sending and receiving of documents Connection of the Equipment This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA On the rear panel of this equipment is a label that contains among other information a product identifier in the format of US AAAEQ TXXXX If requested this number must be provided to the telephone company The REN Ringer Equivalence Number is used to determine the number of devices that may be connected to a telephone line Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call In most but not all areas the sum of the RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to a line as determined by the total RENs contact the local telephone company The REN for this product is part of the product identifier that has the format US AAAEQ TXXXx The digits represented by are the REN without a decimal point e g 10 is a REN of 1 0 An FCC compliant telephone line cable and modular plug is provided with this equipment This equipment is designed to be connected to the telephone network or premise wiring using a compatible modular jack that is Part 68 compliant This equipment may not be used on coin service provided by the telephone company Connection t
50. ical shock O IMPORTANT Leave sufficient space around the power plug so that it can be unplugged easily If objects are placed around the power plug you will be unable to unplug it in an emergency Handling WARNING Do not attempt to disassemble or modify the machine There are high temperature and high voltage components inside the machine which may result in a fire or electrical shock If the machine makes strange noises or gives off smoke heat or strange smells immediately turn OFF the main power switch and disconnect the power cord from the power outlet Then contact your local authorized Canon dealer Continued use of the machine in this condition may result in a fire or electrical shock Do not use highly flammable sprays near the machine If gas from these sprays comes into contact with the electrical components inside the machine it may result in a fire or electrical shock To avoid damage to the power cord and creating a fire hazard always turn OFF the main power switch and unplug the interface cable when moving the machine Otherwise the power cord or interface cable may be damaged resulting in a fire or electrical shock Make sure that the power plug is firmly inserted into the power outlet if the machine was moved Do not use the machine while the connection is loose as doing so may cause a fire Do not drop paper clips staples or other metal objects inside the machine Also do not spill water liqui
51. industrielles savoir ligne t l phonique 2500 pour appareil clavier ou 500 pour appareil cadran impulsions Il est galement possible de raccorder ce t l copieur un syst me t l phonique poussoirs car la plupart de ces syst mes mettent des signaux d appel non normalis s o des codes sp ciaux qui risquent de perturber le fonctionnement du t l copieur C Condition d alimentation Raccordez le t l copieur une prise de courant plus terre trois branches du type simple ou double et qui ne sert pas alimenter un copieur un appareil de chauffage un climatiseur ou tout autre appareil lectrique thermostat L alimentation doit tre de 115 volts et 15 amp res Pour faciliter l installation le jack CA11A doit tre assez proche de la prise de courant Remarques Le pr sent mat riel est conforme aux sp cifications techniques applicables d Industrie Canada Avant d installer cet appareil l utilisateur doit s assurer qu il est permis de le connecter l quipement de la compagnie de t l communication locale et doit installer cet appareil en utilisant une m thode de connexion autoris e II se peut qu il faille tendre la circuiterie int rieure de la ligne individuelle d abonn qui a t install e par la compagnie au moyen d un jeu de connecteurs homologu s rallonge t l phonique Lattention de l utilisateur est attir e sur le fait que le respect des conditions mentionn es ci dessus ne co
52. ine model For more information contact your local authorized Canon dealer pata References Data You Can Import Export Individually You can save load data individually In addition you can exchange data with this machine and other machines which do not support the Import Export All function Address Lists Device Settings Forwarding Settings Address Book Send Function Favorite Settings e Manual gt Remote UI Printer Settings Paper Information Web Access Favorites e Manual gt Web Access Other Data You Can Import Export You can exchange data with this machine and other machines which do not support the Import Export All function SSS Daa O References Quick Menu Information e Manual gt Quick Menu License files for MEAP applications e Manual gt MEAP Data saved from MEAP applications Instruction manuals for each MEAP application Data Relating to MEAP User authentication information registered for the Local Device Authentication system of SSO H Single amp Manual MEAP Sign On H 1 You may be able to back up data stored by MEAP applications depending on the application lt NOTE The passwords and PIN are backed up at the same time However some of the passwords may not be backed up depending on the type of the password If your machine is not connected to a network it is recommended that you print and store important information such as the Address Book See e Manual gt Basic O
53. ing See http www dtsc ca gov hazardouswaste perchlorate for details Using your product to scan print or otherwise reproduce certain documents and the use of such images as scanned printed or otherwise reproduced by your product may be prohibited by law and may result in criminal and or civil liability A non exhaustive list of these documents is set forth below This list is intended to be a guide only If you are uncertain about the legality of using your product to scan print or otherwise reproduce any particular document and or of the use of the images scanned printed or otherwise reproduced you should consult in advance with your legal advisor for guidance Paper Money Travelers Checks Money Orders Food Stamps Certificates of Deposit Passports Postage Stamps canceled or uncanceled Immigration Papers e Identifying Badges or Insignias Internal Revenue Stamps canceled or uncanceled Selective Service or Draft Papers Bonds or Other Certificates of Indebtedness e Checks or Drafts Issued by Governmental Agencies Stock Certificates Motor Vehicle Licenses and Certificates of Title Copyrighted Works Works of Art without Permission of Copyright Owner Preinstallation Requirements for Canon Facsimile Equipment amp NOTE The fax function is available only if the FAX Board is installed A Location Supply a suitable table cabinet or desk for the machine See Specifications in this guide for specific
54. ing manner as this may result in a fire or electrical shock The connection part of the power plug is loose Stress is being applied to the power cord by a heavy object or by affixing it with staples The power plug is loose The power cord is tied in a bundle The power cord protrudes into a walkway The power cord is in front of a heater The fixing unit and its surroundings inside the machine may become hot during use When removing jammed paper or when inspecting the inside of the machine do not touch the fixing unit and its surroundings as doing so may result in burns or electrical shock When removing jammed paper or when inspecting the inside of the machine do not expose yourself to the heat emitted from the fixing unit and its surroundings for a prolonged period of time Doing so may result in low temperature burns even though you did not touch the fixing unit and its surroundings directly Ifa paper jam occurs follow the directions on the touch panel display to remove any jammed paper from inside the machine Do not insert your fingers into any parts not indicated on the touch panel display as doing so may result in personal injury or burns an arr AY CAUTION ATTENTION VORSICHT i amp ATENCION ATTENZIONE CUIDADO 21 When removing jammed paper or replacing the toner cartridge take care not to allow the toner to come into contact with your hands or clothing as this will dirty your hands or cl
55. ls for this machine may result in hazardous radiation exposure As an ENERGY STAR Partner Canon USA Inc has determined that this machine meets the international ENERGY STAR Program for energy efficiency The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the use of computers and other office equipment The program backs the development and dissemination of products with functions that effectively reduce energy consumption It is an open system in which business proprietors can participate voluntarily The targeted products are office equipment such as computers displays printers facsimiles and copiers The standards and logos are uniform among ENERGY STAR participating nations The protocol stack included in this machine has obtained the IPv6 Ready Logo Phase 2 established by the IPv6 Forum 79 mi This machine is compliant with IEEE Std 2600 2008 hereinafter referred to as IEEE 2600 a global information security standard for multifunction peripherals and printers and is able to achieve the security requirements defined in IEEE 2600 For information on how this machine meets the security requirements defined in IEEE 2600 see e Manual gt Security gt IEEE 2600 Security Standard IEEE 2600 1 CC Authentication has not been obtained for this machine by itself Copyright 2012 by Canon Inc All rights reserved No part of this
56. non which damage the Product or cause abnormally frequent service calls or service problems or e use of the Product with non compatible computers peripheral equipment or software including the use of the Product in any system configuration not recommended in any manual distributed with the Product Nor does this warranty extend to any Product on which the original identification marks or serial numbers have been defaced removed or altered ANY SOFTWARE THAT IS DISTRIBUTED WITH THE PRODUCT AND HAS AN ASSOCIATED END USER AGREEMENT IS LICENSED WARRANTED AND PROVIDED ACCORDING TO THE TERMS OF THAT AGREEMENT INCLUDING ANY LIMITATIONS AND DISCLAIMERS THEREIN SUCH SOFTWARE IS SOLD WITHOUT WARRANTY OF ANY KIND BY CANON PLEASE CONTACT CANON IMMEDIATELY IF YOU HAVE NOT RECEIVED A COPY OF THE SOFTWARE SUPPLIER S END USER AGREEMENT CANON RECOMMENDS THAT DATA STORED ON THE PRODUCT S HARD DISK DRIVE BE DUPLICATED OR BACKED UP TO PREVENT ITS LOSS IN THE EVENT OF FAILURE OR OTHER MALFUNCTION OF THE HARD DISK DRIVE THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES AND CONDITIONS EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES AND CONDITIONS REGARDING MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE RELATING TO THE USE OR PERFORMANCE OF A PRODUCT OR ANY ASSOCIATED COMPONENT AND ALL SUCH OTHER WARRANTIES AND CONDITIONS ARE DISCLAIMED NO OTHER EXPRESS WARRANTY CONDITION OR GUARANTY EXCEPT AS MENTIONED ABOVE GIVEN BY ANY PERSON FIRM OR COR
57. nstitue pas une garantie contre les d gradations de qualit du service dans certaines circonstances L indice d quivalence de la sonnerie IES sert indiquer le nombre maximal de terminaux qui peuvent tre raccord s une interface t l phonique La terminaison d une interface peut consister en une combinaison quelconque de dispositifs la seule condition que la somme d indices d quivalence de la sonnerie de tous les dispositifs n exc de pas 5 Le nombre d quivalents sonnerie REN de ce produit est 1 0 Les r parations sur un appareil certifi doivent tre faites par une soci t d entretien canadienne autoris e par le Gouvernement canadien et d sign e par le fournisseur Toute r paration ou modification que pourrait faire l utilisateur de cet appareil ou tout mauvais fonctionnement donne la compagnie de t l communication le droit de d brancher l appareil Pour sa propre protection l utilisateur doit s assurer que les prises de terre de l appareil d alimentation les lignes t l phoniques et les tuyaux m talliques internes s il y en a sont bien connect s entre eux Cette pr caution est particuli rement importante dans les zones rurales caution Au lieu d essayer de faire ces branchements eux m mes les utilisateurs sont invit s faire appel un service d inspection faisant autorit en mati re d lectricit ou un lectricien selon le cas lt NOTE Respecte les limites de la classe
58. o 120 g m Capacity LTR STMTR and EXEC 100 sheets 21 Ib bond 80 g m 11 x 17 LGL and LTRR 75 sheets 21 Ib bond 80 g m Dimensions H x W x D 5 5 8 x 14 3 8 x 14 3 4 144 mm x 365 mm x 373 mm when the auxiliary tray is extended 3 1 2 x 9 5 8 x 14 3 4 87 mm x 243 mm x 373 mm when the auxiliary tray is not extended Installation Space Including the 36 5 8 x 26 3 4 930 mm x 680 mm Main Unit W x D when the auxiliary tray is extended po tem Specifications 1 5 8 x 3 1 2 x 3 3 4 40 mm x 88 mm x 96 mm excluding the attachment kit and cable 45 Super G3 FAX Board AH2 lt NOTE Specifications remain the same even when the Super G3 2nd Line Fax Board is installed Sen Specifications Telephone Line Used Public Switched Telephone Network Scan line Density Scan Normal 8 pels mm x 3 85 line mm Transmission Fine 8 pels mm x 7 7 line mm Super Fine 8 pels mm x 15 4 line mm Ultra Fine 16 pels mm x 15 4 line mm 11 x 17 to STMTR Receiving Paper Sizes 11 x 17 to STMTR 1 When using an IP telephone service facsimile communication may not be performed normally via an IP telephone line It is recommended to use facsimile communication via a general telephone Public Switched Telephone Network line 2 Pels stands for picture elements pixels Send Function Scan Features item Specifications FTP TCP IP SMB TCP IP WebDAV TIFF JPEG PDF XPS OOXML Power
59. o party lines is subject to state tariffs In Case of Equipment Malfunction Should any malfunction occur which cannot be corrected by the procedures described in the e Manual disconnect the equipment from the telephone line cable and disconnect the power cord The telephone line cable should not be reconnected or the main power switch turned ON until the problem is completely resolved Users should contact their local authorized Canon Facsimile Service Dealer for the servicing of equipment If your equipment malfunctions please contact your local authorized Canon dealer from whom you purchased the equipment if under warranty or with whom you have a servicing contract If you are not sure who to contact and have both purchased and are using the equipment in the U S A please refer to the SUPPORT page on Canon U S A s Web site http www usa canon com Rights of the Telephone Company If this equipment imageRUNNER ADVANCE C2230 C2225 causes harm to the telephone network the telephone company may temporarily disconnect service The telephone company also retains the right to make changes in facilities and services that may affect the operation of this equipment When such changes are necessary the telephone company is required to give adequate prior notice to the user However if advance notice is not possible the telephone company will notify the customer as soon as possible Also the customer will be advised of his her right to file a compl
60. othing If they become dirty wash them immediately with cold water Washing them with warm water will set the toner and make it impossible to remove the toner stains When removing paper which has become jammed inside the machine remove the jammed paper gently to prevent the toner on the paper from scattering and getting into your eyes or mouth If the toner gets into your eyes or mouth wash them immediately with cold water and immediately consult a physician When removing jammed originals or paper which has become jammed inside the machine take care not to cut your hands or injure yourself on the edges of the originals or paper If you cannot remove the paper contact your local authorized Canon dealer When removing a used toner cartridge remove the cartridge carefully to prevent the toner from scattering and getting into your eyes or mouth If the toner gets into your eyes or mouth wash them immediately with cold water and immediately consult a physician Do not dismantle the toner cartridge as doing so may cause toner to fly out and enter your eyes or mouth If toner gets into your eyes or mouth wash them immediately with cold water and immediately consult a physician If toner escapes from the toner cartridge make sure not to ingest the toner or allow it to directly touch your skin If toner touches your skin wash it away with soap and water If your skin still feels irritated after washing it or you ingest toner consult a
61. perations 29 s Parts and Their Functions This section provides you with the names and functions of all the parts of the machine For more information on optional products parts and their functions see e Manual gt Optional Products Software External View This section contains an external view of the imageRUNNER ADVANCE C2230 When the Cassette Feeding Unit AF1 Inner Finisher F1 Inner Finisher Additional Tray A1 and Copy Tray J1 Are Attached 30 Q Output Tray Prints and copies are output to this tray 2 Control Panel Includes the keys touch panel display and indicators required for operating the machine 3 Feeder Originals placed in the feeder are fed one sheet at a time to the platen glass for scanning O USB Port 1 USB port to connect USB memory external hard disks and other devices to the machine O Upper Right Cover of the Main Unit Open this cover when clearing a paper jam inside the main unit QO LAN Port Use an Ethernet cable to connect the machine to a network USB Port 2 Use the USB port to connect external hard disks and other devices to the machine You can also connect the machine to a computer using a USB cable O Lower Right Cover of the Main Unit Open this cover when clearing a paper jam inside the main unit 9 Multi Purpose Tray Use the multi purpose tray to feed paper manually and for loading nonstandard paper stock such as
62. registered in the Quick Menu Main Power and Energy Saver Key The machine is provided with a main power switch and the Energy Saver key This section explains how to turn ON the main power O IMPORTANT If you want to turn OFF the main power and then back ON again wait for at least 10 seconds after the main power indicator is turned OFF before turning ON the main power Make sure that the power plug is firmly inserted into the power outlet WARNING Do not connect or disconnect the power cord with wet hands as this may result in electrical shock A Turn ON the main power 1 Open the main power switch cover 2 Press the main power switch to the I side 3 Close the main power switch cover The Main Power indicator on the control panel lights when you turn ON the main power switch Various screens appear when system software is loading If you are using a login service log in using the procedure for the login service you are using lt NOTE You can change the default display that appears after the machine is turned ON from Default Screen after Startup Restoration on the Settings Registration screen See e Manual gt Settings Registration e If this machine is connected to a powered off Macintosh computer by USB cable the computer may turn on automatically when this machine does In this case disconnect the USB cable from the machine You may also be able to solve this problem by using a USB hub be
63. rs to a printing device display device or item respectively that contains PostScript technology created or licensed by Adobe Systems Incorporated and not to devices or items that purport to be merely compatible with the PostScript language Adobe the Adobe logo Adobe LiveCycle Policy Server PostScript the PostScript Logo and PostScript 3 are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries All other trademarks are the property of their respective owners Other product and company names herein may be the trademarks of their respective owners This machine makes effective use of memory to perform print operations efficiently For example as soon as the machine has scanned the original that you want to copy it can immediately scan the next person s original You can also print from this machine using a function other than the Copy function This machine combines multiple operations so that not only copies but various types of jobs are placed in a queue before being processed To avoid confusion when reading this manual the terms scanning printing and copying used throughout this manual are defined below When making a copy the process of scanning originals and printing copies may be described as separate functions Scanning Scanning an original to be copied scanning an original to be sent em
64. s air conditioners heaters or stoves amount is not harmful Ozone etc may be more noticeable during extended use or long production runs especially in poorly ventilated rooms It is recommended that the room be appropriately ventilated sufficient to maintain a comfortable working environment in areas of machine operation Avoid installing the machine in direct sunlight If this is unavoidable use curtains to shade the machine Be sure that the curtains do not block the machine s ventilation slots or louvers or interfere with the electrical cord or power supply Avoid locations where a considerable amount of dust accumulates Avoid locations where ammonia gas is emitted Avoid locations near volatile or flammable materials such as alcohol or paint thinner 23 Avoid locations that are subject to vibration For example avoid installing the machine on unstable floors or stands Avoid exposing the machine to rapid changes in temperature If the room in which the machine is installed is cold but rapidly heated water droplets condensation may form inside the machine This may result in a noticeable degradation in the quality of the copied image the inability to properly scan an original or the copies having no printed image at all Avoid installing the machine near computers or other precision electronic equipment Electrical interference and vibrations generated by the machine during
65. sesssssessssesssssesesssesssssese 9 IPV6 Ready Logo sseeeessecccccccccccscccccsccccssscssssssssssssssssssssssssssssssssssssssssssses 9 Information Security Standard IEEE 2600 esesossssssosesossosssosesesecessesesesesesscsecseee ee 9 Copyrights essences esse esssssesssssesesssessssssesee0 Third Party Software se ssessssssssssese1 The Software Subjected to the Other Conditions se esssssesssssessssesssssesssssesssssessssessssseee 10 Disclaimers esse dass 6 6 ere de dise eee ses nid ee de elie soda see cdi d s dsssss ee de n s ees10 Legal Limitations on the Usage of Your Product and the Use of Images e essssesssssesssssessssssssssse11 Weersin the DS Assises soso ess esesess siennes dessein sede scedecwsssceeecaseesesT 1 Users in Canada ssh sm TR NM ia nn ai ann es de sel Utilisation au Canada essences ses Super G3 none erere rere re creer rere rece seeeeeereseeeeeeseseseeeereseseseseseseesesesesee 5 Important Safety Instructions seccescccccccccsccsesccsescccccccsesscsessesesseseelG Installations esse cece reece reer ees ee sere ee sees essere seeseeseeeeeessseseel iy Power supplyssseseseeseseccesocoesococoeoococoococoococoeoocosoococoeoocosoococoococoeoecoeoe 7 Handling ROC EEE EE EEE EEEEEEEECEEEEEECONEEEEEEEEEEE EEE EEE EEE EEE EEE EEE EEE EEE EEE EEE PA Maintenance and Inspections esesssssssssssssssssesesescesssessseseseseessseseseseseseesesese ee e20 Consumables occcccccccccccvcccccsvcecccsceeccseeeee essere cesses sssseess
66. sheet by sheet into the feeder Place originals into this tray with the surface that you want to scan face up O Original Output Area Originals that have been scanned from the original supply tray are output into the original output area O Original Set Indicator Lights when originals are placed in the original supply tray O Document Feed Scanning Area Scans documents sent from the feeder Q Platen Glass Use the platen glass when scanning books thick originals thin originals transparencies etc 33 Energy Saver Main Menu Select a function SP Quick Menu a Copy Fax Scan and Send Scan and Ka Store Status Monitor Cancel 0 Counter Settings Check Registration Processing Data Error Main Power Q Main Menu Press to display the Main Menu screen If the Main Menu screen is not displayed when using a function it is necessary to press Main Menu before using the function Touch Panel Display The settings screen for each function is shown on this display Six function keys are displayed by default Numeric keys Press to enter numerical values O Energy Saver key Press to set or cancel the Sleep mode Lights when the machine enters the Sleep mode 5 Settings Registration key Press to specify settings registration O Counter Check key Press to display the copy and print count totals on the touch panel display Q Stop key Press to stop a
67. socsooseeee eh Booklet Finisher M1 essences sense csoseeeeA1 Inner Finisher F1 occcccccccccccccccccc cece cece reece eee eer ee reer ee cese 43 Inner Finisher Additional Tray A1 essssssssssssssesssssesssssesssssesssssesssssesesssesesssesesee ee sd Inner 2Way Tray F1 Peer creccrcccrecerecesereeeeseeseseeseseseesseeseeesscesesescssscssccesccess ef Copy Tray J1 nn cre cece cee reece eres se cece eseseseceeeeeeeceesesecesecees eA Copy Card Reader F1 Comer cere e reece reece eee ee eee ee eer eer eeseeeeesereesseseeseeseeceeeeceeseese ef 5 Super G3 FAX Board AH2 oeesecccccccccccccccccccccccccccccccccccscsscccccsscsescsscsscsesessese 46 Send FUNCTION se ee ccccccvccccccccccvcecceceeccee recesses eesseceeseeseeeesesseesesceecceseeeesee Af Network Environment ecccccccccccccccccccccccvccccc cece sce cee cee cee eeeseseeseeseeceseeeesese ss ef Q Hardware Specificationss essessecccscccccscccccccccccrcscsccsccvsssscssssssssscsssssssssssesss4Q Software Specifications nn nono ns ere ee ees eesee ser eeeeeseeseeesesereseseseseees A8 Printer Settings esseeseccccccccccccccccccccscccccscesscvcsccccsscssscvsesssssscesesssessesesess 0G Software Specifications Corer rere r cere ns eee reer ees sense soso 48 CANON imageRUNNER ADVANCE C2230 C2225 SERIES LIMITED WARRANTY sseeeeeeeeeeeeecceeeeseees 49 TERMS OF imageWARE REMOTE SERVICE cosoossoossosescssccescseccsscsecssccsseseesscsesese eee e5Q TERMS OF Content Delivery System TTT Terrerr errr rerre rr err err err ere
68. sseeeseseeeessseeeeeeed Telephone Equipment Cee e rer r er cer eee cere ere reer rere er eee ees eeseeseeeeseeeseseeseeseseeeeeseseed Other Warningse ssesssecccccccccccccccccccccccscscsscscscsssssssssssssssssssssssssssssssssssessed Installation Location and Handling seceesecccsccsescccesccscccssesscscsccsesscses 23 Installation Precautions ececccccccccccccccvccccccccccceeceesee sees ee eee eeeseseeseeresceeeeseeseeseedy Avoid Installing the Machine in the Following Locationse esssssessssssssssesssssesssssessssseess se e23 Select a Safe Power Supply ecccccccccccccccccccccccccccscccccccccessesscssscsscccessssssesses e24 Moving the Machine sesssesssssesssseeseseseseeseseeseeseseesessenesseeseeseseesessesesseese24 Provide Adequate Installation Spaces esseesccesccccccccccccccccvcccccccccccssccsscsscsescssesesel5 Handling Precautions eesssssseesesseseeseesesceseeseeseseeseesssceseesssseseeseesesessessesee ee e26 Backing Up Exporting Datas gt seccccesccccsccccscccesccsesccsccccsessssessesessese e28 Data You Can Import Export Alle essences 28 Data You Can Import Export Individually essssssssssssssssssssssesssssessssessssssesssseesesseee 28 Other Data You Can Import Export eescecccccccccccccccccccccccccccccccvccscsesesscsscsesessese 29 Parts and Their FUNCtIONSs eee cccccccccccccccc ccc ccc ccc cece cece cece cccccccecceccee x External VieWe eeccccccccccccccc cece creer cece cree cere reser ees ee sere ee eeseeseeseeseesesesesese
69. stelveen The Netherlands See htip www canon europe com for details on your regional dealer CANON LATIN AMERICA INC 703 Waterford Way Suite 400 Miami Florida 33126 U S A CANON AUSTRALIA PTY LTD 1 Thomas Holt Drive North Ryde Sydney N S W 2113 Australia CANON CHINA CO LTD 15F Jinbao Building No 89 Jinbao Street Dongcheng District Beijing 100005 China CANON SINGAPORE PTE LTD 1 HarbourFront Avenue 04 01 Keppel Bay Tower Singapore 098632 CANON HONGKONG CO LTD 19 F The Metropolis Tower 10 Metropolis Drive Hunghom Kowloon Hong Kong FT5 4520 010 XXXXXXXXXX CANON INC 2012 PRINTED IN CHINA
70. t it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly telephone extension cord The customer should be aware that compliance with the above conditions may not prevent deterioration of service in some situations The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected to a telephone interface The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five The REN of this product is 1 0 Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas A caution Users should not attempt to make such connections themselves but should
71. tellectual property of rights holders of the SOFTWARE 3 You may use the SOFTWARE solely for use with the PRODUCT 4 You may not assign sublicense market distribute or transfer the SOFTWARE to any third party without prior written consent of rights holders of the SOFTWARE 5 Notwithstanding the foregoing you may transfer the SOFTWARE only when a you assign to a transferee all of your rights to the PRODUCT and all rights and obligations under the conditions governing the SOFTWARE and PRODUCT and b such transferee agrees in writing to be bound by all these conditions 6 You may not decrypt decompile reverse engineer disassemble or otherwise reduce the code of the SOFTWARE to human readable form 7 You may not modify adapt translate rent lease or loan the SOFTWARE or create derivative works based on the SOFTWARE 8 You are not entitled to remove or make separate copies of the SOFTWARE from the PRODUCT 9 The human readable portion the source code of the SOFTWARE is not licensed to you Notwithstanding 1 through 9 above in case any other license conditions accompany third party software modules these software modules are subject to these other conditions as well ACCEPTANCE THE TERMS OF THIS THIRD PARTY SOFTWARE STATED HERE OR IN RELATED WARRANTY PROVISIONS SHALL BE DEEMED ACCEPTED UPON YOUR USE OF THE PRODUCT FOR ONE OR MORE OF ITS NORMAL PURPOSES IF THERE HAS BEEN NO OTHER PRIOR EXPRESS ACCEPTANCE THE TERMS
72. ts inside the machine Blocking these openings can cause the machine to overheat Never place the machine on a soft surface such as a sofa or rug Do not install the machine in the following locations A damp or dusty location A location near water faucets or water A location exposed to direct sunlight A location subject to high temperatures A location near open flames Do not install the machine near alcohol paint thinner or other flammable substances If flammable substances come into contact with electrical parts inside the machine it may result in a fire or electrical shock Do not place the following items on the machine If these items come into contact with a high voltage area inside the machine it may result in a fire or electrical shock If these items are dropped or spilled inside the machine immediately turn OFF the main power switch and disconnect the power cord from the power outlet Then contact your local authorized Canon dealer e Necklaces and other metal objects Cups vases flowerpots and other containers filled with water or liquids A caution Do not install the machine in unstable locations such as unsteady platforms or inclined floors or in locations subject to excessive vibrations as this may cause the machine to fall or tip over resulting in personal injury Do not remove the machine s leveling feet after the machine has been installed as this may cause the machine to fall or
73. tween the machine and the Macintosh The response of the buttons and keys may not be optimal immediately after you turn ON the main power of the machine If you set Quick Startup Settings for Main Power to On in Preferences Settings Registration the tone sounds when turning ON the main power of the machine Depending on the situations the machine does not startup quickly and the tone does not sound If the machine takes longer to startup than usual see e Manual gt Settings Registration Ifyou are using Department ID Management with the Copy Card Reader F1 see e Manual gt Optional Products Software If you are using Department ID Management see e Manual gt Basic Operations If you are using SSO H see e Manual gt Basic Operations 35 You can press Energy Saver to make the machine enter the Sleep mode and reduce power consumption If the machine is idle for a certain period of time the machine will enter the Auto Sleep mode to minimize energy consumption Press Energy Saver to cancel the Sleep mode and resume normal machine operations amp NOTE The machine can receive and print documents from a personal computer when it is in the Sleep mode l fax and fax documents can also be received while the machine is in the Sleep mode This machine performs a procedure to protect the memory when the machine is shut down This enables the machine to be shut down safely even if there are any
74. ty replacement shall not extend the original warranty period of the Product This limited warranty shall only apply if the Product is used in conjunction with compatible computers peripheral equipment and software Canon shall have no responsibility for such items except for compatible Canon brand peripheral equipment covered by a separate warranty Separate Warranty Repairs of such Canon brand peripheral equipment shall be governed by the terms of the Separate Warranty Non Canon brand equipment that may be distributed with the Product is sold AS IS and without warranty of any kind by Canon including any implied warranty regarding merchantability or fitness for a particular purpose and all such warranties are disclaimed The sole warranty if any with respect to such non Canon brand items is given by the supplier or producer thereof For further information on software see below This warranty shall be void and of no force and effect if the Product is damaged as a result of a abuse neglect mishandling alteration electric current fluctuation or accident b improper use including failure to follow operating or maintenance instructions or environmental conditions prescribed in Canon s operator s manual or other documentation c installation or repair by other than authorized service representatives qualified by Canon who are acting in accordance with Canon s service bulletins d use of supplies or parts other than those distributed by Ca
75. used 2 Order a CA11A modular jack which should be installed by the telephone company If the CA11A jack is not present installation cannot occur 3 Order a normal business line from your telephone company s business representative The line should be a regular voice grade line or an equivalent one Use one line per unit If the Super G3 2nd Line Fax Board is installed you can use a multi line DDD Direct Distance Dial line or IDDD International Direct Distance Dial line if you communicate overseas NOTE Canon recommends an individual line following industry standards i e 2500 touch tone or 500 rotary pulse dial telephones A dedicated extension off a PBX Private Branch eXchange unit without Call Waiting can be used with your facsimile unit Key telephone systems are not recommended because they send nonstandard signals to individual telephones for ringing and special codes which may cause a facsimile error C Power Requirements The power outlet should be a three prong grounded receptacle Single or Duplex It should be independent from copiers heaters air conditioners or any electric equipment that is thermostatically controlled The rated value is 115 volts and 15 amperes The CA11A modular jack should be relatively close to the power outlet to facilitate installation Notice This product meets the applicable Industry Canada technical specifications Before installing this equipment users should ensure tha
76. vailable Corner Staple Double Staple mode Staple Size LTR 50 sheets 17 to 22 Ib bond 64 to 82 g m 30 sheets 22 to 28 Ib bond 83 to 105 g m 2 sheets 29 Ib bond to 80 Ib cover 106 to 220 g m 11 x 17 LGL and LTRR 30 sheets 17 to 22 Ib bond 64 to 82 g m 20 sheets 22 to 28 Ib bond 83 to 105 g m 2 sheets 29 Ib bond to 80 Ib cover 106 to 220 g m Power Source Maximum Power From the main unit Approximately 39 W Consumption Dimensions H x W x D 10 1 4 x 23 1 4 x 21 5 8 260 mm x 590 mm x 550 mm when the auxiliary tray is extended Approximately 31 Ib 14 0 kg when the optional Inner Finisher Additional Tray A1 is attached Installation Space Including the 40 1 4 x 26 3 4 1 021 mm x 680 mm Main Unit W x D when the multi purpose tray and the auxiliary tray are extended Inner Finisher Additional Tray A1 Capacity Per Tray See the specifications of Capacity Per Tray Inner Finisher Additional Tray A1 in Inner Finisher F1 Inner 2Way Tray F1 Oo otm Specifications S O Paper Size Weight Type Size 12 x 18 12 5 8 x 17 11 16 11 x 17 LGL LTR LTRR STMT STMTR EXEC Custom size 3 7 8 x 5 1 2 to 12 5 8 x 18 99 mm x 139 7 mm to 320 mm x 457 2 mm and Envelopes Weight 17 Ib bond to 80 Ib cover 64 to 220 g m Type Thin Plain 1 18 to 22 Ib bond 65 to 82 g m Plain 2 22 to 26 Ib bond 83 to 99 g m Plain 3 27 to 28 lb bond 100 to 105 g m Recycled
77. x 457 2 mm and Envelopes Kakugata 2 envelopes can only be loaded horizontally Warm Up Time After Powering ON when Quick Startup Settings for Main Power is set to Off 34 seconds After Powering ON when Quick Startup Settings for Main Power is set to On 10 seconds The time until key operations can be performed on the touch panel display is 7 seconds or less Even if Quick Startup Settings for Main Power is set to On the machine does not startup quickly depending on the situations Returning from the Sleep mode 10 seconds Activation time may vary depending on the environment and conditions under which the machine is being used At a room temperature of 68 F in all above cases First Copy Time Full Color 8 9 seconds Black and White 5 9 seconds 37 tem Specifications S O Copy Speed Direct sheet minute imageRUNNER ADVANCE C2230 imageRUNNER ADVANCE C2225 12 x 18 7 7 11 x 17 15 15 LGL 15 15 LTR 30 25 LTRR 20 20 STMTR 30 25 EXEC 30 25 Except when paper is fed from the multi purpose tray The copy speed may vary depending on the settings for paper type paper size and the sending method When continuously copying adjustments for machine temperature or image quality may cause machine operations to pause or become slow Margin Top 1 8 4 0 mm Left and Right 1 8 2 5 mm Bottom 1 8 2 5 mm Magnification Regular paper size Same Ratio Direct Reduction 1 0 78 LGL LTR 1 0 73
78. you make such changes or modifications you could be required to stop operation of the equipment If your equipment malfunctions please contact your local authorized Canon dealer from whom you purchased the equipment if under warranty or with whom you have a servicing contract If you are not sure who to contact and have both purchased and are using the equipment in the U S A please refer to the SUPPORT page on Canon U S A s Web site http www usa canon com This product complies with 21 CFR Chapter 1 Subchapter J as a Class laser product under the U S Department of Health and Human Services DHHS Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968 Also this product is certified as a Class 1 laser product under IEC60825 1 2007 This means that the product does not produce hazardous laser radiation Since radiation emitted inside the product is completely confined within protective housings and external covers the laser beam cannot escape from the machine during any phase of user operation Do not remove protective housings or external covers except as directed by the equipment s manual The label shown below is attached to the paper drawer s right cover and toner supply port cover DANGER yie ken rater when open an inteocsseeued enramaernw cevmamnancen saree CAUTION ass 28 vste tasen aouron vie opex axo 2a INTEALOGRS DEFEATED AVOID EXPOSURE TO TME BEM zo AT

Canon C2225 Owner's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents