Bulldog Security 903 User's Manual
Contents
1. If the alarmis violated it will stop and rearmitself after 30 seconds Special Situations Allows you to lower or shut off the sensitivity of your shock sensor for special situation Example when parked near a construction zone or in heavy rain Remotely programmabl e Limited Lifetime Warranty Guarantees life long protection TECHNICAL ASSISTANCE Should you need help First check our website at www bull dogsecurity com wires htm or call our toll free Tech Support Hotline Monday through Friday 9AM 8PM and Saturday 10AM 4PM EST at 800 878 8007 You must give the following information Name Telephone Number with Area Code Fax number if applicable Year Make and Model of the vehicle The model number of the system you are installing The type of assistance you are requesting If you give the above information you will be called back as soon as possible usually within 10 minutes I NSTALLATI ON NSTRUCTI ONS 1 Locate a solid well grounded metal surface under the hood Any metal fender firewall or metal plate will do For the loudest sound the siren should point down CAUTION Do not mount close to exhaust or other high temperature areas Make sure the alarmas well as the metal it is mounted to is solid with no moving parts nearby The siren should not point up as moisture could collect in the siren horn and damage the system See figure 1 2 Use three self tapping screws included to secure the alarm Screwinto2. a well grounded metal surface CAUTION You must use all three screws See figure 2 3 Connect the RED power wire with the supplied alligator clip and clip it to any constant 12 volt supply such as the battery If installation is correct the alarmwill chirp three times See figure 3 4 For maximum range keep the YELLOW antenna wire straight and as far away from metal as possible Figure 1 Figure 2 Figure 3 Red Possible Locations Positive Antenna Self tapping Scr ews Cable OPERATING NSTRUCTI ONS NOTE Before operating your alarm slide the protector down attached to the back of your remote transmitter snap off the back and snap to the front Arming Press transmitter Button 1 Arm The systemwill chirp once indicating that the systemis armed Disarming Press transmitter Button 2 Disarm The systemwill chirp twice indicating that the systemis disarmed NOTE If you ear three chirps when disarming the vehicle experienced an impact violation while armed If you hear four chirps when disarming the vehicle experienced a current violation while armed This is a good time to inspect the vehicle for forced entry marks pain dings or scratches and check to be sure a whee isn t partially removed Adjusting the Shock Sensor Sensitivity NOTE The factory setting on the shock sensor should be acceptable for most vehicles To adjust the shock sensor disarmthe system press and hold the transmitter Button
3. 3 finder until the alarm chirps four times approximately five seconds immediately release the button Tap your hood above the alarmat the sensitivity level you wish The harder you hit the car the less sensitivity the alarm wil be The alarm will then chirp three times The shock sensor is now set at this sensitivity Any shock that is equal to or greater will sound the alarm Set the sensitivity as often as you wish however the sensitivity level will remain set until the battery is disconnected or you reset it If you do not tap the car it wil automatically go to maximum sensitivity This setting is only acceptable if the car is parked inside a garage Car Finder While the systemis armed press and release transmitter Button 3 finder The alarmwill chirp eight times This is used to locate your vehicle in a crowded parking lot Instant Panic Press and release transmitter Button 4 panic to sound the instant panic siren The siren will activate for 30 seconds and then shut off To stop the siren before the 30 seconds press any of the four transmitter buttons This feature functions at all times whether the alarmis armed or disarmed or the engine is off or running Special Situations Sometimes when you park your car in heavy rain near a construction zone near trucks etc you may wish to lower the sensitivity of your alarm FOR THIS ARMING ONLY To lower the sensitivity by 50 press transmitter Button 1 to arm and then again withi
4. INSTALLATION GUIDE OWNER S GUI DE ALARM MODELS 901 902 903 908 CONTENTS System Features send xe ew aren nr i oriri wae lw ae Ka eS ae as 1 Technical ASSISTANCE arp ae keke Ae hae a ened Pee heme aw a 1 ise Shr on IMSErUCE ONS sc cca cedw as ce dace davandtea we de 1 Oper ar ie PSCC ONS sons nea ds eid o n eee OR DERE 2 BUDD SECURITY Technical Assistance All tech personnel are expertly qualified to answer any technical questions Technicians are available Monday through Friday from 9 00 a m until 8 00 p m and Saturday 10 00 a m until 4 00 p m Address 288 Canton Avenue Wintersville Ohio 43953 Telephone Phone 740 264 4710 800 878 8007 Fax 740 264 7306 SYSTEM FEATURES One Piece Self Contained Fast and easy to install usually 5 to 10 minutes with no experience Fits virtually any Only One Wre vehicle Long Range Four Button Remotely activates your alarm Slide protection stops accidental alarm activation Remote Transmitter Extra Loud Siren Deters thieves fromfurther tampering Current Sensing The alarm will sound with changes in current Example Dome light or ignition switch Electronic Will warn away without going into full alarm activation Dual Stage Shock Sensor Instant Panic Mode Should you feel threatened you can remotely activate the siren with the press of a button Remote Car Finder Helps you locate your vehicle in a crowded parking lot by chirping the siren eight times Automatic Alarm Reset
5. n two seconds after arming To shut the shock sensor off completely press transmitter Button 1 twice within two seconds after arming The next time the alarmis set it wil go back to the original setting Setting the Current Sensor Disarmthe system Press and hold transmitter Button 4 panic until the alarmchirps twice approximately 5 seconds This indicates that current sensing is now turned off To turn Current Sensing back on Disarm the system Press and hold transmitter Button 4 panic until the alarmchirps once approximately 5 seconds This indicates that current sensing is now turned off NOTE Factory setting is Current Sensing ON Adding A New Transmitter With the system disarmed press and hold Button 1 arm until the unit chirps approximately 10 seconds At this time release Button 1 and press any button on the transmitter you want to add The alarmwill respond with a second chirp Both transmitters will now operate the system
Download Pdf Manuals
Related Search