Bryston B100 User's Manual
Contents
1. 4 BALANCE gt VOLUME MUTE CLIP POWER B100 SST INTEGRATED AMPLIFIER DIGITAL Select AUX 2 BUTTON In B100 DA models pressing this button switches between Analog and Digital Input modes See notes above and in CONNECTIONS section of this manual In B100 amp B100 P models this button selects the line level analog audio AUX 2 input 1 4 STEREO 3 conductor HEADPHONE JACK It is recommended that this jack be used only with headphones having gt 50 ohms impedance Plugging ina1 4 phone plug will automatically mute the power amplifier outputs and the MUTE led will illuminate red BALANCE CONTROLS MOTORIZED Adjusts the left versus right channel VOLUME levels Pressing the left 4 or right gt CONTROL buttons will attenuate that channel by 1 decibel for each press of the button When either channel is attenuated this way the LED above the affected Can be operated manually or via the remote control MUTE CONTROL Pressing this button mutes both power amplifier channels fully and the LED lights red Pressing the button again releases the mute condition and the LED extinguishes The mute control does not affect the RECORD OUT outputs or the headphone outputs channel will be illuminated green Pressing the button a 7th time will cause that channel to fully mute and the LED above the button will light red The2. PROGRAMMING the T2 12v TRIGGER OUTPUT By default the 72 triggered output is inactive To program this output to become active whereupon a control voltage of 12Vdc will appear across T2 amp terminals whenever spe cific source is selected use the handheld remote control as follows e Select the source that you want to coincide with T2 going active e While pointing the remote control at the B100 press the CODE button followed by the three digit code 247 using the keys numbered 1 through 0 in the illustration at the left On your remote control these keys or buttons are labeled AUX PH 2 TUNER 4 D1 7 e The three digit code should be entered within a few seconds of pressing CODE button or the unit will automatically return to normal operation e To clear the 2 trigger output press the CODE button followed by the digit code 248 AUX PH 2 TUNER 4 D2 8 HAND HELD INFRA RED REMOTE CONTROL The Bryston model B100 comes standard with a full function hand held remote control unit The hand held remote unit is powered by two AAA batteries To change the battery remove the bot tom cover plate by removing the four Philips screws on the rear of the remote unit Ensure that the 3 100 TWO CHANNEL POWER AMPLIFIER batteries are correctly oriented and properly seated in the battery holder The B100 remote is a full function remote It allows selection of all sources volu
3. RS232 REMOTE CONTROL Using the DB9 female connector at the rear of the unit the B100 can receive commands via a null modem cable at 9600 baud 8 data bits no parity and 1 stop bit 9600 8 N 1 Valid commands will return the gt character indicating that the unit is ready to receive a new command An invalid command will return the character These serial data commands are as follows 000 power off 015 power on off toggle 081 select digital source 1 D1 001 select analog source 1 A D 019 balance left 082 select digital source 2 D2 002 select analog source 2 AUX PH 020 balance right 083 select digital source 3 D3 003 select analog source 3 CD 029 power on 084 select digital source 4 D4 004 select analog source 4 TUNER 058 mute on 245 set reset Pass Through mode 005 select analog source 5 TV 059 mute off 247 Set Trigger 2 for current source 006 select analog source 6 VIDEO 061 record monitor toggle 248 Clear Trigger 2 for current source 007 volume up 062 record monitor on 255 System reset restore defaults 008 volume down 063 record monitor off PASS THROUGH MODE PASS THROUGH mode sets the pre amp gain to 1 unity gain and locks out the volume amp balance controls for any single analog audio source For example if the Front Left and Front Right outputs of a home theater surround sound processer were connected to the TV input of the B100 and then PASS THROU
4. balance control does not affect the RECORD OUT outputs OUTPUT BINDING POSTS Connect these outputs are connected to speaker loads of greater than or equal to 4 ohms The RED binding post is the positive phase signal and the BLACK binding post is the negative phase output signal ground CONNECTED SEPARATE SWITCH In the CONNECTED position the pre amp section output is internally connected to the power amp section input In the SEPARATE position the POWER AMP IN jack will accept the input signal to the power amp If this jack is left open while the switch is in the SEPARATE position that particular channel will be effectively inoperative JACKS Unbalanced or single ended input impedance 10KQ amp outputs ANALOG DIGITAL DUAL MODE INPUTS In B100 DA models equipped with a D A converter module these two jacks accept SPDIF serial data input signals In other non digital models B100 amp B100P these jacks accept only analog audio signals TOSLINK optical data input connectors These optical digital TOSLINK inputs are only active in B100 DA models CHASSIS GROUND SCREW TERMINAL SPDIF DIGITAL AUDIO INPUTS in 100 PREAMP OUT RECORD OUT AUX1 PHONO 0000 RIGHT CHANNEL By O ourpur RECORD IN VIDEO TUNER POWER AMP IN CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN
5. be accessed by selecting D1 D2 D3 and D4 sources with the DAC feature enabled by pressing the DIGITAL Select button on the left end of the front panel Activate the DAC feature by pressing the DIGITAL Select AUX 2 button on the left side of the front panel or A D on the remote The LED below the DIGITAL Select button will turn Green Pressing any of the fol lowing four buttons will cause their LEDs to light green as well to indicate a PCM digital source is present and connected properly e SPDIF 1 is accessed by selecting D1 on the front panel or the remote e SPDIF 2 is accessed by selecting D2 on the front panel or the remote e Optical 1 is accessed by selecting D3 on the front panel or the remote e Optical 2 is accessed by selecting D4 on the front panel or the remote The source LED s will turn GREEN when a PCM digital bit stream is present If there is no bit stream available or an incorrect bit stream NON PCM the LED will turn RED You may re select Analog by simply depressing the DIGITAL Select AUX 2 button once more and the LED will extinguish All of the above functions are available from the hand held remote control as well MOVING MAGNET PHONO STAGE OPTION The B100 P contains a moving magnet phono stage The Phono Stage is modular and can be added to the stan dard B100 model later if required by your Bryston dealer Bryston s MM Phono section features state of the art accuracy in equalization extrem
6. AMPLIFIER INPUT SELECT BUTTONS DIGITAL MODE BP100 DA only INPUT SELECT BUTTONS ANALOG MODE When the LED above the AUX 2 DIGITAL gt Select switch is illuminated When only one of the source select LEDs is illuminated the unit is in green concurrently with either the D1 CD D2 TUNER D3 TV or 04 ANALOG MODE The name under the button is the source selected VIDEO LEDs the unit is in DIGITAL MODE The D1 D2 D3 or D4 buttons POWER BUTTON amp LED This button toggles the power on amp off The LED indicates the following are then used to select one of the 4 digital audio inputs Press the D1 button Press the D2 button Pressthe D3 button Press the D4 button SPDIF 1 source is selected SPDIF 2 source is selected TOSLINK 1 sourceis selected TOSLINK 2 sourceis selected GREEN normal operation Exceptions are as follows RED standby In B100 P models the AUX 1 PHONO LED indicates that the Blinking RED receiving valid data moving magnet phono inputis selected Blinking RED GREEN thermal overload or other In B100 amp B100 DA models the AUX 1 PHONO LED indicates fault that the analog audio AUX 1 input is selected CLIPPING LED When illuminated RED indicates that either or both channels are clipped overloaded or overdriven DIGITAL Select D1 D2 T ANALOG AUX2 AUX1 PHONO CD IR SENSOR D3 D4 O REC Q VIDEO HEADPHONE O
7. ECTRIQUE NE PAS OUVRIR TRIGGERS TiC T2 C RECORD OUT PRE AMP OUT 4 4 CONNECTED gt SEPARATE RECORD IN POWER IN 4 00 LEFT OUTPUT EO 3 37 3 00 15 A There are no user serviceable parts inside the B100 Please refer any servicing to qualified personnel BRYSTON LIMITED WARRANTY Bryston audio circuits are warranted to be free from manufacturing defects for twenty 20 years from the original date of manufacture The warranty includes parts and labour Bryston Digital circuits are warranted for five years from the original date of manufac ture The warranty includes parts and labour Bryston circuits having motorized moving parts are warranted for three years from the original date of manufacture The warranty includes parts and labour Bryston will remedy the problem by repair or replacement as we deem necessary to restore the product to full performance Bryston will pay return shipping during the first three years of warranty coverage The warranty is fully transferable to the original owner and all subsequent owners during the warranty period Warranty coverage is automatic and commences with the original date of manufacture which is kept on file at Bryston In the event of a defect or malfunction contact Bryston s repair centers for return authorization Products must be returned using
8. FEN ean RISK OF HAZARDOUS ENERGY CE PRECAUTION MAKE FEN eg SPEAKER CONNECTIONS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR AUX1 PHONO RECORD OUT AMP OUT 00000 LEFT CHANNEL 060000 VIDEO RECORD IN POWER AMP IN PETERBOROUGH ONTARIO CANADA Model B100 SST 120VAC 60Hz 975VA CONNECTED Serial No B100 000001 SEPARATE Date 0509 SEPARATE TOSLINK OPTICAL ei g only r s LEFT OUTPUT INPUTS D4 D3 AUX 2 B100 amp B100P AUX IR B1 D S 00 CAUTION Replace fuse with same type 6 3A 250v 5x20mm ATTENTION Utiliser un defusible de RS232 12 TIGERS Vi TIC T2 C RS232 JACK For remote control from computer or other suitably equipped controllers such as Crestron amp AMX meme type 6 3A 250v 5x20mm A FUSE DRAWER Accepts one 5mm X 20mm fuse Replace only with same type of fuse listed on adjacent label Always remove power cord before opening fuse drawer IEC 320 POWER INLET Use only approved IEC 320 power cords 12V REMOTE TRIGGER CONNECTOR A 12Vdc signal appears across the T1 C terminals whenever the B100 is ON A 12Vdc control signal also appears across the T2 C terminals whenever a pre programmed input source is selected Refer to Programming the T2 12v Trigger Output and Remote Power Control 12 Volt Trigger Connector in the B100 Owner s Manual fo
9. GH was engaged then whevever TV input is selected the volume and balance controls would be locked at unity gain If other inputs were subsequently selected volume and balance controls return to normal operation for those other input sources Only the TV inputs would be locked at unity gain PASS THROUGH mode therefore can only be assigned to one input at a time but that input can be any one of the analog audio inputs The power amplifier stage is not affected by PASS THROUGH mode PASS THROUGH mode can only be set or reset by sending the digit code 245 to the B100 either from the handheld IR remote control or via the RS232 serial data input See Sending Codes to the B100 via the IR Handheld 4 DROSTO B100 TWO CHANNEL POWER AMPLIFIER Remote Control amp Wired RS232 Remote Control To reassign PASS THROUGH mode to a different input source simply select the desired input and re send the 245 code to the B100 To turn the deactivate PASS THORUGH mode select the current Pass Through input and then send the 245 code to the B100 The 245 toggles PASS THROUGH mode on and off DIGITAL to ANALOG D A CONVERTER OPTION The B100 DA comes equipped with stereo Digital to Analog converter D A or DAC module This module is also retrofittable to standard B100 units A unique feature of the B100 DA is its ability to utilize up to four independent digital sources two SPDIF and two TOSLINK These four digital inputs can
10. Prison B100 INTEGRATED AMPLIFIER OWNER S MANUAL For models B100 B100 DA amp B100 P 1 2 3 4 J 6 T 8 10 11 12 13 14 IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus includ ing amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of t
11. ater than 50 ohms should be used AUXILIARY IR INPUT This mono 1 8 8mm phone jack allows a direct connection to equipment whose remote control system pro vides an output from their infra red LED drive circuit The signal connected to this jack which is expected to be a 5 volt logic level should be 22 5Vdc and lt 10Vdc The tip of the phone jack is positive and the ring is negative LED STATUS INDICATORS CLIPPING This LED light emitting diode will flash RED when the output waveform is clipped thus indicating an overload condition MUTE Lights RED to indicate the outputs are muted POWER GREEN indicates normal operation RED indicates Standby Blinking RED GREEN a fault or thermal overload problem in the unit ER LY SS LI CD mn B100 TWO CHANNEL POWER AMPLIFIER ANALOG Aux2 DIGITAL Select In B100 DA models when this LED is illuminated green concurrently with either D1 D2 D3 or D4 LEDs it indicates that the digital inputs D1 SPDIF D2 SPDIF D3 TOSLINK or D4 TOSLINK have been selected In B100 amp B100 P models when illuminated green this LED indicates that the line level ana log audio input AUX 2 has been selected AUX1 CD TUNER TV SAT VIDEO amp RECORD BALANCE One of these input source LEDs will light green to Indicate the active input In digital mode these LEDs will light RED if the bit stream is either absent or unacceptable When the left right signal balance is being shifte
12. connected internally to PRE AMP OUT via the CONNECTED SEPARATE slide switch located on the rear panel When this switch is in the SEPARATE position however any line level audio input can be used at the POWER AMP INPUT jacks to drive the amplifier In B100 DA models the AUX2 01 02 input jacks accept only SPDIF PCM bit streams They do NOT accept 1 ER LY SS LI CD mn B100 TWO CHANNEL POWER AMPLIFIER analog audio input signals In B100 P models which are equipped with a moving magnet phono equalization module the inputs labeled AUX1 PHONO accept moving magnet phono cartridge inputs These inputs are NOT line level inputs in the B100 P and cannot be used as such LINE LEVEL ANALOG AUDIO OUTPUTS The Bryston B100 integrated amplifier comes equipped with 2 pairs of gold plated analog RCA jacks for out puts PREAMP OUT and RECORD OUT e PREAMP OUT is normally connected internally via the CONNECTED SEPARATE switch to POWER AMP IN e RECORD OUT output is not affected by volume balance or mute controls DIGITAL AUDIO INPUTS In the B100 DA model which contains a stereo D A converter module there are 4 digital audio inputs avail able Two TOSLINK optical inputs are selected by pressing the D3 TOSLINK 1 or D4 TOSLINK 2 buttons on the front panel when in digital mode or on the handheld remote Two SPDIF coaxial inputs can be connected to the B100 DA using the RCA input jacks labeled D1 and D2 To select these inputs first plac
13. d one of these LEDs will light to indicate which channel is being attenuated Balance can be adjusted in 1dB increments to up to 6dB in either direction Stepping past 6dB in either direction will mute that channel fully and the LED for that channel will turn red When both LEDs are on red PASS THROUGH mode is indicated See Pass Through Mode on page 4 REMOTE POWER CONTROL gt 12 VOLT TRIGGER CONNECTOR Two trigger outputs are provided A12Vdc signal is placed across B100 SST Power Amplifier Bryston part number 0 110 11104 the 1 pins of the 12V REMOTE TRIGGER IN OUT CONNECTOR TRIGGERS connector whenever Ti C T2 the unit is fully powered up Then the unit goes into standby Separate twined this voltage is removed A 12Vdc signal will be placed B across the other pair of 12V I TRIGGER output pins 2 0000 whenever a certain user suBSEQUENT AMPLIFIERS etc z AMPLIFIERS etc 12V present only when Ey grammed input is selected as OV present programmed souce input ar i h the B100 is selected an Strip wires 1 4 the source input see below 70 299 12VDC 12VDC aimed ON for programming instructions When any other input source is selected the 12Vdc control voltage will be removed from these pins Please note that means here and both pins are electrically connected and identical o TON POWER BALANCE IR STOQ BR1
14. e the unit in digital mode by pressing the DIGITAL Select button on the front panel or the A D button on the handheld remote and then press the D1 or D2 button on the front panel or on the remote When the green LED above the font panel DIGITAL SELECT switch button in ON concurrently with either the D1 CD D2 TUNER D3 TV or D4 VIDEO LEDs then digital mode is engaged Note Whatever digital input was previously selected in Digital Mode will be automatically reselected upon re entering Digital Mode from Analog Mode Similarly when re entering Analog Mode from Digital Mode the previously selected analog input will be automatically re selected See also the DIGITAL to ANALOG CONVERTER OPTION section for more information HEADPHONE JACK There is a quarter inch headphone output jack available on the front panel of the Bryston B100 integrated amplifier The headphone output is driven directly from the preamplifier section utilizing separate headphone buffers Inserting the headphone jack mutes the loudspeakers automatically indicated by the mute LED on the front panel turning red The B100 PREAMP OUT is also muted You can adjust the volume setting of the headphones by using the volume control on the front of the B100 inte grated amplifier You may also utilize the remote control unit to adjust headphone volume The headphones cannot be muted with the remote control unit or the front panel Mute Only headphones with impedances of gre
15. ely low noise and distor tion and provides headroom margins sufficient to prevent overload from any known phono source To access the Phono section simply plug your left right turntable interconnect leads into the left right AUX 1 PHONO inputs on the rear panel of the B100 and press the AUX 1 PHONO button on the front panel The AUX 1 PHONO LED will turn green If your turntable provides a separate ground lead system noise may be minimized by connecting it to the ground lug in the center of the rear panel B100 SPECIFICATIONS POWER AMPLIFIER SECTION PREAMPLIFIER SECTION Power Output 100 watts per channel into 80 Frequency response 20Hz to 20KHz 05dB 180 watts per channel into 40 IMD or THD lt 007 Input Impedance 50K ohms single ended High Level Sensitivity 500mV Sensitivity 1v 100 Watts into 8 ohms Noise 100dB 20Hz to 20KHz Distortion THD noise lt 0 005 20Hz to 20kHz at 100 ref 1V input watts into 8 ohms IMD lt 0 010 60Hz 7KHz mixed 4 1 Noise gt 108dB below rated output with 20Hz to 22KHz bandpass filter GENERAL HEN Slew Rate gt 60 volts per microsecond Dimensions 17 or 19 w x 4 75 h x 16C Power Bandwidth lt 1 over 100 kHz 43 2 or 48 3mm wide 12 1 mm high x Damping Factor Over 500 at 20 Hz ref 8 ohms 40 6mm deep Power consumption idle 30va maximum power 600va Weight approx 30 Ibs 13 6kg Heat load idle 100 btu hr max power 288 btu hr ROSOR B100 TWO CHANNEL POWER
16. he obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combi nation to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not oper ate normally or has been dropped WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO OBJECTS FILLED WITH LIQUIDS SUCH AS VASES ARE PLACED ON THE EQUIPMENT TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS DISCONNECT THE POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE IacsSsrvan B100 TWWO CHANNEL POWER AMPLIFIER INTRODUCTION Thank you for purchasing a Bryston B100 integra
17. iate left and right loudspeakers SEPARATE PRE AMP OUT amp POWER AMP IN JACKS These two pair of RCA jacks allow for the independent use of the stereo amplifier section within a multi chan nel audio or video system On the rear panel there are connections labeled PRE AMP OUT preamplifier output and POWER AMP IN power amplifier input along with two slide switches one per channel labeled Separate Connect This feature allows you to separate or connect the preamplifier section of the B100 from the power amplifier section thus producing a separate stereo preamp and separate stereo power amplifier WIRED SERIAL DATA REMOTE CONTROL There is one RS 232 one AUX IR input and two 12 volt trigger output connections as well The RS 232 is bi directional and allows for future software downloads from the Bryston website It also interfaces with control systems such as Crestron and AMX CHASSIS GROUND A chassis ground thumb screw terminal is provided on the rear panel 12 VOLT TRIGGER CONNECTOR These 12Vdc control outputs allow the B100 to exert on off control over compatible equipment See REMOTE POWER CONTROL for more information LINE LEVEL ANALOG AUDIO INPUTS The Bryston B100 integrated amplifier comes equipped with 8 pairs of gold plated analog RCA input con nectors TV CD AUX 1 PHONO AUX 2 SPDIF VIDEO TUNER RECORD IN and POWER AMP IN All have and input impedance of 50K ohms e POWER AMP IN is normally
18. me up or down the volume control is a motor driven design mute left right balance power on off and discrete code entry We recommend maintaining a direct line of sight between the hand held remote unit and the front of the B100 to ensure the most efficient operation of the remote features PROGRAMMING the HANDHELD REMOTE CONTROL The automatic motion sensing backlight function in the handheld infra red remote control unit can be disabled by entering the 3 digit code 792 as follows 1 Press and hold the CODE button for 5 seconds Release when the LED flashes red 2 After the LED stops flashing enter the 3 digit code 792 by pressing the buttons D1 D3 then AUX PH see illustra tion on page 3 3 To re enable the motion sensing backlight function repeat steps 1 and 2 above To completely disable the backlight enter the 3 digit code 797 as follows 1 Press and hold the CODE button for 5 seconds Release when the LED flashes red 2 After the LED stops flashing enter the digit code 797 by pressing the buttons D1 D3 then D1 see illustration on page 3 3 To re enable the backlight repeat steps 1 and 2 above SENDING CODES to the B100 via the IR HANDHELD REMOTE CONTROL Press the CODE button on the remote control the red LED will light and then enter the 3 digt code as listed in the Wired RS232 Remote Control section below The LED will flash to confirm transmission and then extinguish WIRED
19. original packaging material only Packing material may be purchased from Bryston if necessary This warranty is considered void if the defect malfunction or failure of the product or any component part was caused by damage not resulting from a defect or malfunction or abuse while in the possession of the customer Tampering by persons other than factory authorized service personnel or failure to fully comply with Bryston operating instructions voids the warranty This warranty gives you specific legal rights and you may also have other rights which may vary from province to province and country to country BRYSTON SERVICE CANADA BRYSTON SERVICE USA BRYSTON SERVICE OUTSIDE CANADA amp the USA 24 STEINWAY BLVD UNIT 48 79 COVENTRY ST SUITE 5 CONTACT YOUR LOCAL DISTRIBUTOR ETOBICOKE ONTARIO NEWPORT VERMONT OR CANADA M9W 6T8 U S A 05855 2100 CHECK OUR WEB SITE www bryston ca E MAIL BRYSTON DIRECTLY info bryston ca PHONE 416 675 2585 PHONE 802 334 1201 FAX BRYSTON DIRECTLY 705 742 0882 FAX 416 675 3103 FAX 802 334 6658 PHONE BRYSTON DIRECTLY 705 743 5325 E mail cdnser gta igs net E mail usaser bryston ca BRYSTON LTD 677 NEAL DRIVE P O BOX 2170 PETERBOROUGH ONTARIO CANADA 7Y4 B100 MANUAL 2005 04 29 BR1 gt
20. r more information AUX IR Input For connection to infra red LED drive circuits of compatible remote control equipment Tip of the 1 8 3mm 2 conductor phone plug is positive and the ring is negative Input signal should be 2 5Vdc lt 10Vdc ROSOR B100 TWO CHANNEL POWER AMPLIFIER B100 INSTALLATION SUGGESTED MINIMAL CLEARANCE ENVELOPE FRONT PANEL 3 00 19 91 3 00 TOP VIEW Rear Panel 6 00 CLEARANCE ENVELOPE TOP VIEW 23 03 23 03 CLEARANCE ENVELOPE END VIEW 19 00 17 03 FRONT PANEL 3 00 SNES 0 7 12 Model B100 SST 120VAC 60Hz 975VA Serial No B100 000001 0509 RIGHT OUTPUT WARNING RISK OF HAZARDOUS ENERGY MAKE PROPER SPEAKER CONNECTIONS made in PETERBOROUGH ONTARIO CANADA CONNECTED RECORD OUT TV AUX1 PHONO 0000 A 4 lt P AUX1 PHONO cD TV see SPDIF DIGITAL AUDIO INPUTS in 100 RIGHT CHANNEL LEFT CHANNEL SEPARATE D2 D1 S B100DA only TOSLINK B100DA only N N N __ JE N IL DIGITAL AUDIO P A A y D4 NUTS J 4 4 4 4 POWER IN RECORD IN VIDEO TUNER AUX 2 B100 amp B100P AUX 2 TUNER VIDEO AUXIR B100 amp B100P CAUTION A FER PRECAUTION 12 paga RISQUE DE CHOC EL
21. ted amplifier We are confident it will provide you with many years of musical enjoyment We would welcome any suggestions or comments you may have regarding the operation of your Bryston amplifier In the unlikely event that your amplifier may require service Bryston recommends that you retain the original shipping box and packaging material for future use if required SETUP RECOMMENDATIONS You may place your B100 integrated amplifier in any convenient location Make sure you position the ampli fier to maintain a direct line of sight between the hand held remote and the remote sensor eye located on the front panel If plugged in the B100 will remain in standby indicated by the RED power LED on the front panel The amplifier is powered up by engaging the power button located on the front panel of the B100 or by depressing the POWER button on the hand held remote control unit The B100 will power up momentarily with mute engaged indicated by the mute LED turning red on the front panel it will then turn off within a few seconds The POWER LED will stay lit green indicating normal operation CONNECTIONS LOUDSPEAKERS Connect your loudspeakers ensuring that the positive red and ground black terminals gold plated 5 way binding posts on the Bryston B100 integrated amplifier are connected to the positive and ground terminals on your loudspeakers Make certain the left and right speaker outputs on the amplifier are connected to your appropr
Download Pdf Manuals
Related Search