Black Box VSW-HDMI4X4-B User's Manual
Contents
1. ES 6 1 DTS HD DTS HD HRA DTS HD Master PCM 2CH Digital Video Support Full HD resolution 480i 480p 720p 1080i 1080p Function Control Key ALL OFF RECALL ENTER MEMORY LOCK EDID HDCP CEC Support HDCP 2 0 compliant CEC compliant HDMI I O Connector HDMI Type A SMD 19 pin female HDMI Support HD 1080p 60 Hz H36 bit deep color 3D 1 4a formats Infrared Frequency 38 kHz IR External Distance 1000 feet 300 m maximum Preview Output Supports 1 preview output port simultaneously via Output 1 Safety Approvals CE FCC RoHS Source Status Automatically scan sources inputs via LED Temperature Tolerance Operating 32 to 100 F 0 to 38 C Video Bandwidth Double data rates 340 MHz total 6 75 Gbps bandwidth Power Input 100 230 VAC 50 60 Hz Output 12 VDC 3 A Consumption 3880 mA maximum Size 1 75 H 1U x 9 85 W x 19 D 4 4 x 25 x 48 2 cm Weight 3 08 Ib 1 85 kg Page 8 724 746 5500 blackbox com Chapter 2 Overview 2 Overview 2 1 Introduction The VSW HDMI4X4 B is a high performance 4X4 matrix routing switch for HDMI signals This switch supports data rates up to 6 75 Gbps enabling 1080p HDMI formats and UXGA WUXGA DVI resolution to any HD display High Definition Digital signals can be selected and distributed to any eight outputs simultaneously The switch is fully HDMI and HDCP compliant with RoHS CE and FCC certification It supports high re2. INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL 1 Dn uo A Ww N 9 10 11 13 14 15 16 Save the carton and packing material even if the equipment has arrived in good condition If you ever need to ship the unit use only the original factory packing Read all documentation before operating your equipment Retain all documentation for future reference Follow all instructions printed on unit chassis for proper operation Do not spill water or other liquids into or on the unit or operate the unit while standing in liquid Make sure power outlets conform to the power requirements listed on the back of the unit Do not use the unit if the electrical power cord is frayed or broken The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords and plugs convenience receptacles and the point where they exit Always operate the unit with the AC ground wire connected to the electrical system ground Precautions should be taken so that the means of grounding of a piece of equipment is not defeated Voltage must be correct and the same as that printed on the rear of the unit Damage caused by connection to improper AC voltage is not covered by any warranty Power down and disconnect the unit from power voltage before making connections Never hold a
3. el 0 1 O OOOPOCOOOO5 5 0 0OEDE o 10 ZAM FROME Rada 10 PAP REAN PAIN lsc tak cea A AN 11 E O RNA 13 ar EA 13 A SR 14 4 OPEra setas lil iii ibi cdi 15 LN EDID SEUD rn oa io ia 15 4 2 Embedaecd EDID MOS tn ies 15 43 COPY EDID aio E ii 15 AA EDID Statis naea eat facts da uaa a a a ea T a O E 16 4 5 How to Set Up Fast Speed Start FSS FUNCTION cc cccccccceccsccsccsecsecseessesseeecsecsecsecsassasssessecsessecsesascsssaseseeeeteeseeeseens 17 4 6 Auto Mode Definitionen nina nece 17 4 7 Consumer Electronics Control CEC SCtup ccccccccccccccscsscssccsecsecsecseesasssesaecsessecsssssesasssessecsesseesssaecssssesseseeteesaeeseees 17 4 8 Front Panel Control FUNCION Scion a ida 18 AQ Remote A O A AN 18 4 10 IR Remote Custom and Data Codes NEC Standard oooccnnccnincccconcconncconncnono nono n cnn cono canon nono n nc aan n anar nro n nan c can nc can nccins 19 SS A AT 20 51 Connect PC or Control Micra ici 20 Bide RS 232 Protocol COMME dial 20 G Toubes nooi anal id 21 6 1 Comading Bak BOK tii iii 21 6 2 SAPPHO a a Packaging eere E E E aeasuseeace ears 21 724 746 5500 blackbox com Page 7 Chapter 1 Specifications 1 Specifications Controls IR remote control IR external port with 1 3 5 mm earphone jack Select and Function buttons on front panel RS 232 series interface Digital Audio Support Multi audio formats 5 1 7 1 MAT MLP Dolby Digital Dolby TrueHD Dolby Digital Plus DTS DTS
4. o 10 11 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas Todas las instrucciones de operaci n y uso deben ser seguidas El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc El aparato el ctrico debe ser usado nicamente con carritos o pedestales que sean recomendados por el fabricante El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra o superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u otros aparatos incluyen
5. DMI Matrix Switch MM Disp MM Display wW Projector VX HDMI TP 100M Transmitter Display m 4x4 HDMI Matrix Switch VSW HDMI4x4 B y WA PC Blu ray PS 3 Laptop VX HDMI TP 100M Receiver o o Figure 3 1 Typical application using the 4x4 HDMI Matrix Switch 724 746 5500 blackbox com Page 13 Chapter 3 Installation 3 2 IR Extender X FE CE RoHS 95 EC INPUT DC 12v 0000 desa O O RS 232_ eco DISTANCE maximum 300 M 1000 feet Figure 3 2 IR extender connection NOTE When you plug the external IR extender into the switch the front panel IR receiver remains active STEP 1 i Ring Sleeve Tip Signal Tip Ring 9 Sleeve GND x y Sleeve Tip center STEP 2 VCC GND 0 UU Le ia GND Cable Signal Cable Switcher IR EXT In Z FEC e INPUT 00000 ofesssjo O O eee Cable IR Receiver Figure 3 3 How to set up the IR extender components Steps 1 3 Page 14 724 746 5500 blackbox com 4 Operation 4 1 EDID Setup Step Number Action Step 1 Step 2 Step 3 Press the EDID button Press the SOURCE 1 or 2 button row Press the ENTER button Chapter 4 Operation Table 4 1 EDID function for HDMI matrix switch Result The display will show the currently selected EDID mode The button will flash blue and the displa
6. E y 2 y 3 y 4 a HE 7 eo 9 11 12 13 8 10 14 Figure 2 2 Front panel diagram 2 Table 2 1 Front panel components Number Component Description Power Switch The power switch turns the unit on and off The LED will light red to indicate that the switch is on and is receiving power The switch will remember that last state during a power cycle When power is removed and restored the last configuration will be used 2 Input Status Display Input sources 1 to 4 LEDs light blue to indicate that a video source is present on that input 3 Output Status Display Each output destination channel shows which input source is assigned 4 Destination Select Buttons Separate outputs 1 through 4 select buttons are provided for each destination assignment Separate inputs 1 through 4 select buttons are provided for each source selection Source buttons 1 and 2 are used to change EDID 5 Source Select Buttons i modes when the EDID button is pressed 6 IR Sensor The IR sensor receives IR commands from the supplied remote control or third party emitter Disables mute video on all destinations OR selects the same source to all destinations Option 1 Press ALL followed by the OFF button The display will show 0 indicating that all destinations have no video selected 7 Function Key ALL Option 2 Press ALL followed by Source 1 through 4 The display will show the source selected Press ENTER and the preset source selection will be assig
7. VI digital video signals HDCP compliant DVI does not support audio HDMI digital video audio connector HDMI female connector NOTE With the proper adapters you can use the switch with DVI digital video signals HDCP compliant DVI does not support audio Component Description Connect 12 VDC 5 A power supply here Support one IR Extender When you plug the external IR extender into the switch the front panel IR receiver remains active RS 232 control port enables interfacing a PC computer or touch panel to the switch via the DB9 female connector for serial RS 232 control Connect a signal link of HDMI direct digital video audio to this female HDMI connector The connector supports HDMI digital video audio and HDMI digital video sources Preview port HDMI signal is the same as Output 1 Connect a signal link of HDMI direct digital video audio to this female HDMI connector The connector supports HDMI digital video audio and HDMI digital video sources HDMI Digital Video Audio connector with fixed screw Input 1 4 Connect a signal link of HDMI direct digital video audio to this female HDMI connector The connector supports HDMI digital video audio and HDMI digital videp sources HDMI Digital Video Audio connector with fixed screw Output 1 4 Page 12 724 746 5500 blackbox com Chapter 3 Installation 3 Installation 3 1 Installation Diagram Figure 3 1 shows a sample application using the 4x4 H
8. VSW HDMII4X4 B lt gt BLACK BOX NETWORK SERVICES Switch 4 HDMI source devices plus IR to 4 HDMI displays Supports 1080p 3D HDMI or DVI formats IR with RS 2 or IR remote control Customer Order toll free in the U S Call 877 877 BBOX outside U S call 724 746 5500 Support FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 Information Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com e E mail infoOblackbox com Trademarks Used in this Manual Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks of BB Technologies Inc Dolby and Dolby Digital are registered trademarks of Dolby Laboratories Licensing Corporation HDMI is a registered trademark of HDMI Licensing L L C Xbox and Windows are registered trademarks of Microsoft Corporation Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners We re here to help If you have any questions about your application or our products contact Black Box Tech Support at 724 746 5500 or go to blackbox com and click on Talk to Black Box You ll be live with one of our technical experts in less than 30 seconds Page 2 724 746 5500 blackbox com FCC and IC RFI Statements Federal Communications Commission and Industry Canada Radio Frequency Interference Statements This equ
9. ch is malfunctioning do not attempt to alter or repair the unit It contains no user serviceable parts Contact Black Box Technical Support at 724 746 5500 or info blackbox com Before you do make a record of the history of the problem We will be able to provide more efficient and accurate assistance if you have a complete description including e the nature and duration of the problem e when the problem occurs e the components involved in the problem e any particular application that when used appears to create the problem or make it worse 6 2 Shipping and Packaging If you need to transport or ship your 4X4 HDMI Matrix Switch e Package it carefully We recommend that you use the original container e If you are returning the unit make sure you include everything you received with it Before you ship for return or repair contact Black Box to get a Return Authorization RA number 724 746 5500 blackbox com Page 21 NOTES Page 22 724 746 5500 blackbox com NOTES 724 746 5500 blackbox com Page 23 Black Box Tech Support FREE Live 24 7 Tech support the way it should be PY Pl A 7 A Great tech support is just 30 seconds away at 724 746 5500 or blackbox com lt BLACK BOX About Black Box Black Box provides an extensive range of networking and infrastructure products You ll find everything from cabinets and racks and power and surge protection products to media converters an
10. d Ethernet switches all supported by free live 24 7 Tech Support available in 30 seconds or less Copyright 2013 Black Box Corporation All rights reserved VSW HDMI4X4 B version 2 724 746 5500 blackbox com
11. do amplificadores que producen calor El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato 12 Precauci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada 13 Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato 14 El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante 15 En caso de existir una antena externa deber ser localizada lejos de las lineas de energia 16 El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo 17 Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n 18 Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparato ha sido tirado o su cubierta ha sido da ada Page 4 724 746 5500 blackbox com Safety Information Safety Information NOTE THIS SAFETY
12. g the front panel Input 1 4 select buttons the supplied IR remote control or through the RS 232 serial communications port e On powerup the switch will return to its last used setting before it was powered down Table 4 8 IR Remote Control Key 2 TE ON in Figure A 2 E 4 1 Description OCO 3 i DESTINATION 1 Switch Power ON 2 Switch Power OFF D DOI 4 SOURCES 3 Destination 1 4 output selection Press the destination button to select the output display channel Source 1 4 input source selection 4 Press input 1 4 sources with selection ALL OFF EDID OOD LOCK RECALL MEMORY ENTER 4x4 HDMI MATRIX SWITCH Figure 4 1 IR remote button Function Key ALL function selection button OFF function selection button EDID function selection button LOCK function selection button RECALL function selection button MEMORY function selection button ENTER function selection button 724 746 5500 blackbox com 4 10 IR Remote Custom and Data Codes NEC Standard HOW TO SETUP IR CODES CUSTOM CODE O9F6 POWER ON O9F6 A15E POWER OFF O9F6 A25D PRESS DESTINATION then PRESS SOURCE DESTINATION 1 O9F6 10EF DESTINATION 2 O9F6 20DF DESTINATION 3 O9F6 30CF DESTINATION 4 O9F6 40BF For example Select Destination 1 to show Source 1 4 The IR Data Code list Press Destination 1 Source 1 OO9F6 Press Destination 1 Source 2 O9F6 Press Destination 1 Source 3 O9F6 Press Desti
13. in 5 seconds 12 Function Key LOCK e Press and hold the LOCK button for two seconds to lock out the front panel y e Press and hold the LOCK button for two seconds to re enable the front panel 13 Function Key EDID Press EDID to select new EDID mode and select source button 1 or 2 to change embedded EDID mode 14 19 rackmount ears Converts a desktop switch to a 19 inch rackmount switch Brackets are included 2 4 2 Rear Panel O 4 O B o 2 O O 4 om e O T IR EXT S gt E gt gt Aso O Figure 2 3 Rear panel 724 746 5500 blackbox com Page 11 Chapter 2 Overview Number Component DC Power Inlet IR Extender Control RS 232 Connection Preview Output 01 HDMI Inputs 1 2 3 4 HDMI Outputs 1 2 3 4 HDMI Table 2 2 Rear panel components Connector Connector Descripton Power jack DC jack inner OID 2 1 mm Power input 12 VDC 5A IR extender jack Female jack inner OID 3 5 mm Remote port DB9 female connector HDMI digital video audio connector HDMI female connector NOTE With the proper adapters you can use the switch with DVI digital video signals HDCP compliant DVI does not support audio HDMI digital video audio connector HDMI female connector NOTE With the proper adapters you can use the switch with D
14. ipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe A prescrites dans le Reglement sur le brouillage radio lectrique publi par Industrie Canada 724 746 5500 blackbox com Page 3 N In OM Statement strucciones de Seguridad Normas Oficiales Mexicanas Electrical Safety Statement 1 2 3 4 5 oN OD
15. lace for future reference To reduce the risk of electric shock do not remove the cover from the unit No user serviceable parts inside Refer servicing to qualified personnel To reduce the risk of fire do not expose the unit to rain water or excessive moisture Do not force switched or external connections When moving the unit disconnect the serial port connections first then the power cable and finally the interconnecting cables to other devic es Do not attempt to clean the unit with chemical solvents or aerosol cleaners as this may damage the unit Use a clean dry cloth Installation of this unit should be in a cool dry place away from sources of excessive heat vibration dust moisture and cold WARNING To prevent electric shock do not use this polarized plug with an extension cord receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure To prevent electric shock match wide blade of plug to wide slot Fully insert CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE Page 6 724 746 5500 blackbox com Table of Contents Table of Contents le PEC MON ibi abril 8 A E sean gesmnpcnek tees accvagaccsilsandene E O 9 A A 9 ZZ PO db 9 E AA ON TR CAOS 9 2 4 Hardware BIE
16. mber Action Step 1 Press the EDID button Step 2 Press the EDID button Press to enable all the source buttons 1 4 to which Copy the destination EDID to selected sources Confirm entries Table 4 5 Copy EDID to ALL inputs Result The button will flash blue and the display will show the current embedded EDID Status Copy EDID from selected destination Copy the destination EDID to all sources Confirm entries Table 4 6 EDID status Result The button will flash blue and the display will show the current embedded EDID Status To exit Page 16 724 746 5500 blackbox com Chapter 4 Operation 4 5 How to Set Up Fast Speed Start FSS Function Table 4 7 Setting up Fast Speed Start FSS function Step Number Action Result Step 1 Press the Destination 1 4 button row then press the Source 1 4 button row To set up and install all devices Step 2 Press the EDID button Select an optimum status of embedded EDID mode Step 3 Press the ENTER button Confirm entries Step 4 Press the EDID button Select the EDID FSS mode Step 5 Press the ENTER button Confirm entries 4 6 Auto Mode Definition The switch will detect and automatically copy the EDID for the highest common supported video mode of the displays Example for a single destination Destination Device 1 will be set to the highest common audio and video mode supported by Source 1 Example for multiple destinations The highe
17. nation 1 Source 4 O9F6 ALL O9F6 BO4F ENTER O9F6 B34C EDID O9F6 B748 LOCK O9F6 B54A SOURCE 1 O9F6 O1FE SOURCE 2 O9F6 02FD SOURCE 3 09F6 O3FC SOURCE 4 O9F6 04FB 10EF O9F6 O1FE 10EF O9F6 O2FD 10EF O9F6 O3FC 10EF O9F6 OAFB Chapter 4 Operation 724 746 5500 blackbox com Page 19 Chapter 5 RS 232 Serial Interface 5 RS 232 Serial Interface 5 1 Connect a PC or Control System For a complete list of commands refer to the extended RS 232 Protocol Instruction Manual Figure 5 1 RS 232 DB9 connector Table 5 1 RS 232 serial interface pinouts Pin RS 232 Defintion 1 Not used 2 TX Transmitter 3 RX Receiver 4 Not used 5 GND Ground 6 Not used 7 Not used BO Not used 9 Not used 5 2 RS 232 Protocol Commands You can control the switch via the RS 232 serial control port to interface to a PC or similar third party control system The serial communication parameters are 9600 baud 8 bit No Parity and 1 stop bit This is often referred to as 9600 8N1 When the unit recognizes a complete command it will perform the requested action There is no delimiter character required O Enter the number O Enter the letter NOTE Make sure you use the correct keys for letter O and number 0 Page 20 724 746 5500 blackbox com Chapter 6 Troubleshooting 6 Troubleshooting 6 1 Contacting Black Box If you determine that your 4X4 HDMI Matrix Swit
18. ned to all destinations Page 10 724 746 5500 blackbox com Chapter 2 Overview Table 2 1 Continued Front panel components Number Component Description Disables mutes video to selected channels Press the OFF button followed by any destination channel e Press button 1 through 4 to select the output destination The display will show 0 for the selected channel indicating no video selected 8 Function Key OFF The system will show previously stored presets up to a total of 16 Presets are stored in local memory using Source keys 1 through 4 or Destination keys 1 through 4 as the memory preset location Function Key RECALL Press the RECALL button 9 preview e Press 1 through 4 on either Source or Destination row e Press ENTER The preset configuration will execute Operation completes NOTE Operation will abort if no keys are pressed within 5 seconds Function Key Enter or 10 DEMO Press ENTER to confirm entries The system will store presets up to a total of 8 Presets are stored in local memory using Source keys 1 through 4 or Destination keys 1 through 4 as the memory preset location e Configure desired matrices e Press the memory button 11 Function Key Memory e Press 1 through 4 on either Source or Destination row or SAVE e Press ENTER to ready memory location Or press MEMORY again to cancel operation Operation completes NOTE Operation will abort if no keys are pressed with
19. output status e Supports preview output port simultaneously with Output 1 e Supports IR Remote and IR Extender with distance up to 1000 feet 300 m maximum e Provides EDID configuration via Internal modes e Consumer Electronic Control CEC switch can be all open or OFF e Remembers the last state during a power cycle e When power is removed and resorted the last configuration will be restored 2 3 What s Included Your package should include the following items If anything is missing or damaged contact Black Box Technical Support at 724 746 5500 or info blackbox com e Main console unit e IR remote control e IR extender receiver e RS 232 cable e 100 230 VAC 12 VDC 3 A universal power supply 724 746 5500 blackbox com Page 9 Chapter 2 Overview e 19 inch rackmount brackets e User manual 2 4 Hardware Description Figures 2 1 and 2 2 show the front panel of the switch and Figure 2 3 shows its back panel Tables 2 1 and 2 2 describe the components 2 4 1 Front Panel O o pers A as SBLACKBOX o OUTPUT 1 2 3 4 R www blackbox com RECALL MEMORY LOCK O 1 2 3 4 EDID AlL OFF ENTER INPUT 2 4 1 3 ww E UU i O O POWER O A O 1 3 2 6 5 4 7 OUTPUT 1 2 3 4 Cas aE E giii bac ei j ee a a ae fas user y
20. power switch in the ON position Do not use the unit near stoves heat registers radiators or other heat producing devices 12 Do not block fan intake or exhaust ports Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit such as a bed rug carpet or completely enclosed rack If the unit is used in an extremely dusty or smoky environment the unit should be periodically blown free of foreign matter Do not remove the cover Removing the cover will expose you to potentially dangerous voltages There are no user serviceable parts inside Do not drive the inputs with a signal level greater than that required to drive equipment to full output Non use periods The equipment s power cord should be unplugged from the outlet when left unused for a long period of time Service information Equipment should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the equipment C The equipment has been exposed to rain D The equipment does not appear to operate normally or exhibits a marked change in performance E The equipment has been dropped or the enclosure damaged 724 746 5500 blackbox com Page 5 Important Safety Instructions IMPORTANT SAFETY INSTRUCTIONS To get the best from this product please read this manual carefully Keep it in a safe p
21. solution HDMI sources routed to HDMI displays monitors projectors or audio receivers The EDID can be selected between seven different modes or copied from the attached displays You can control the switch via front panel push buttons the IR remote or RS 232 2 2 Features e Matrix switches 4 HDMI digital source devices to 4 HDMI devices e Supports HDMI digital video w embedded audio DVI format and complies with CEC HDCP 2 0 e Includes 7 function key controls e Supports worldwide EDID modes for HDTV resolutions e Enables link speeds of up to 6 75 Gbps link clock rate of 340 Hz and supports HDMI 1 4a 3D formats e Works with wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV DTV resolutions 480i 480p 5761 576p 720p 1080i and 1080p e Compatible with all HDMI source devices PC monitors plasma HD displays HDTV and audio receivers amplifiers e Provides digital video TMDS formats resolution up to 1080p 60 with Deep color 36 bit e Supports digital audio Dolby TrueHD Dolby Digital Dolby Digital Plug ex DTS DTS HD DTS HD Master DTS EX PCM PCM2 LPCM2 e Choose from three ways to control the user interface front panel push button IR wireless remote control and third party RS 232 controller via simple ASCII e Supports worldwide control functions ALL OFF RECALL ENTER MEMORY EDID LOCK e Supports built in EDID modes external copy and auto mode e Front panel LEDs show active input and
22. solution of all connected display devices NOTE The stored copied EDID table will be static and not change unless you switch to one of the other EDID modes It is not possible to copy from the same destination numerous times To do a new copy from the same destination you either have to first copy from another destination or first select one of the embedded EDID modes 724 746 5500 blackbox com Page 15 Chapter 4 Operation Step Number Action Step 1 Press the EDID button Press one of the sepa Destination buttons 1 4 Press one of the source Step3 buttons 1 4 Step 4 Press the ENTER button Step Number Action Step 1 Press the EDID button Table 4 3 Copy EDID to single input Result The button will flash blue and the display will show the current embedded EDID Status Copy EDID from the selected destination Copy to the destination EDID to the selected source Confirm entries Table 4 4 Copy EDID to multiple inputs Result The button will flash blue and the display will show the current embedded EDID Status Step 2 Press one of the Destination buttons 1 4 Copy EDID from the selected destination Step 3 he EDID should be copied Step 4 Press the ENTER button Step Number Action Step 1 Press the EDID button Press one of the aap Destination buttons 1 4 Press All button to Step 3 P select all sources Step 4 Press the ENTER button 4 4 EDID Status Step Nu
23. st supported common audio and video mode for Destination Devices 1 2 and 3 will be copied to the active source 4 7 Consumer Electronics Control CEC Setup In brief CEC allows HDMI devices to control each other when necessary and allows the user to operate multiple devices with one remote control handset To enable CEC e Press EDID button e Press ALL button e Press EDID button The pre set configuration will execute To disable CEC e Press EDID button e Press OFF button e Press EDID button The pre set configuration will execute NOTE Not all devices support CEC Check with your device s User s Guide for additional information and specifications For stable operation only connect HDMI connections with the switch powered OFF 724 746 5500 blackbox com Page 17 Chapter 4 Operation 4 8 Front Panel Control Functions See Chapter 2 4 9 Remote Control Before making any connections to the switch observe the following e Make sure that the voltage supply matches the label on the supplied plug 10 e Make sure that the power switch is OFF e Make sure that all system grounds are connected to a common point e Avoid powering equipment with a system from multiple power sources that may be separated by large distances e Connect all audio video sources and destination equipment e Power on all source and destination audio visual sources e For each destination output select the appropriate input source by usin
24. y will show the current embedded EDID status To set EDID mode The switch will return to Operation mode 4 2 Embedded EDID Modes NOTE Only works with HDMI displays For use with DVI displays see Section 4 3 Copy EDID Press EDID gt Source gt Enter where source Source 1 or 2 There are a total of 8 EDID modes Mode Number Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 Mode 7 Mode 8 Mode 1 FSS Mode 5 H36M Mode 2 H24 3D Mode 6 1280 x 1024 DVI D Mode 3 H24M 3D Mode 7 1920 x 1200 DVI D Mode 4 H36 Mode 8 AUTO Embedded EDID Setup FSS Fast Speed Start H24 3D 1080p 24 bits H24M 3D 1080p 24 bits H36 1080p 36 bits H36M 1080p 36 bits 1280 x 1024 DVI D 1920 x 1200 DVI D AUTO lt Default gt 4 3 Copy EDID Press EDID gt Destination gt Source gt Enter The switch will learn the destination EDID and pass the selected source Table 4 2 Embedded EDID modes Description Automatically capture the most suitable EDID from Destination to Source Audio support PCM 2CH Audio support MAT MLP 7 1CH PCM 2CH one bit audio 2CH AC3 5 1CH DTS 5 1CH PCM 7 1CH Dolby Digital 7 1CH DTS HD 7 1CH Audio support PCM 2CH Audio support MAT MLP 7 1CH PCM 2CH one bit audio 2CH AC 3 5 1CH DTS 5 1CH PCM 7 1CH Dolby Digital 7 1CH DTS HD 7 1CH Frequency 60 Hz PC mode no audio Frequency 60 Hz PC mode no audio All outputs will be set to the highest common re
Download Pdf Manuals
Related Search