Black & Decker Scrugun 2055-573 Owner's Manual
Contents
1. This booklet is provided for your convenience in the use and care of your new Black amp Decker tool These instructions include operation safety pre cautions preventive maintenance maintenance and other pertinent data to assist you in assuring long life and dependab e service SEALS SAFETY RULES _ FOR POWER TOOLS power tool institute a oie KNOW YOUR POWER TOOL Read owner s manual carefully Learn its applications and limitations as well as the specific potential hazards peculiar to this tool ses GROUND ALL TOOLS UNLESS DOUBLE INSULATED If tool is equipped wth three prong plug it should be plugged into a three hole electrical receptacle If adapter is used to accommodate two pronged receptacle the adapter wire must be attached to a known ground Never remove third prong 3 KEEP GUARDS IN PLACE and in working order 4 KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents 5 AVOID DANGEROUS ENVIRONMENT Don t use power tool in damp or wet locations And keep work area well lit 6 KEEP CHILDREN AWAY All visitors should be kept safe distance from work area 7 STORE IDLE TOOLS When not in use tools should be stored in dry en or locked up place out of reach of children 8 DON T FORCE TOOL It will do the job better and safer at the rate for which it was designed 9 USE RIGHT TOOL Don t force small tool or attachment to do the job of a heav2. Point 1 15 16 Overall Length No 3 Point 1 15 16 Overall Length No 54592 No 54594 BIT TIP HOLDERS 1 4 HEX DRIVE SHANKS No 61108 Non Magnetic For 4 Bit Tips Bit Tips No 63957 Magnetic For 14 TIPS 14 HEX BIT Phillips No 1 Point Phillips No 2 Point Phillips No 3 Point D No 38403 No 38404 No 38405 j Phillips Pozedriv No 2 Point E No 61102 Phillips Pozedriy No 3 Point No 61104 z 38406 Frearson Type Reed amp Prince SOCKETS Use with Square Drive Shanks Hex G Cat No Type Size Diam 20512 Non Mag 1 4 1 2 20514 Non Mag 5 16 1 2 20516 Non Mag 3 8 9 16 M0 38420 Magnetic 1 4 PAG 38422 Magnetic 5 16 ey ee Magnetic 3 8 9 16 38424 SLOTTED HEAD SCREWS are easily driven with Bit and Finder accessories Finder Sleeve No 65879 adapts the thread on the _ front of the clutch housing to hold all 719000 series Finders _ which then become integral with the housing If you prefer separate Bits with Rotating Finders are available to mount directly in the Scrugun chuck See your B amp D Catalog No 1 for the ene Selection of accessories os FACTORY SALES and SERVICE CENTERS CE E EN i cae aitia ie wi pla s Be Sin nee e iei Area Telephone _ Area Telephone _ Code No i Code No gt ALABAMA Birmingham 35233 1717 Third Ave Sou
3. eee 418 Laurier Avenue West DON MILLS Toronto esceeerseseseresereeees 2 Valleybrook Drive QUEBEC CITY P Qe scscssicsecisssvienesonescoeevessieres 330 St Roch Street EDMONTON ALBERTA 0eeeeee 11440 Ave 142 Street REGINA SASKATCHEWAN 0 0 0 0 ee 1076 Albert Street HALIFAX NOVA SCOTIA 2 cereeeenseseneess 803 McLean Street SASKATOON SASK Diamond Ind Center Quebec amp 33rd St HAMILTON ONTARIO 180 Parkdale Ave N VANCOUVER 10 B Cossoine 24 West 2nd Ave LONDON ONTARIO 631 Commissioners Rd East WINNIPEG 10 MANITOBA 0 s esse 934 St James St AUTHORIZED SERVICE STATIONS MAINE Westbrook OHIO Youngstown TEXAS Corpus Christi MISSISSIPPI Jackson PENNSYLVANIA Allentown El Paso NEVADA Reno Las Vegas Erie VIRGINIA Roanoke SOUTH CAROLINA Charleston NEW YORK Schenectady WASHINGTON Yakima SOUTH DAKOTA Rapid City WEST VIRGINIA Wheeling CONNECTICUT New Haven DELAWARE Wilmington FLORIDA Pensacola IDAHO Boise Lewiston ALABAMA Montgomery ALASKA Anchorage Fairbanks ARIZONA Tucson CALIFORNIA Fresno Stockton SALES AND SERVICE SUBSIDIARIES Vienna Austria Brussels Belgium Copenhagen Denmark Helsinki Finland idstein Germany Athens Greece Tokyo Japan Mexico D F Monterrey Guadalajara Mexico Rotterdam Netherlands Auckland Wellington Christchurch New Zealand Grorud Norway Joha
4. 50 San Antonio 78210 1111 South Presa Street 512 LE4 4611 Bladensburg 20710 4501 Baltimore Avenue 301 779 3808 UTAH Salt Lake City 84115 1541 S Second West Street 801 HU 6 7056 MASSACHUSETTS Boston 02135 12 Market St Brighton 617 ST 2 6264 VIRGINIA Falls Church 22046 129 Annandale Road 703 533 1147 MICHIGAN Detroit 48219 18133 W McNichols Rd 313 534 8880 Norfolk 23517 337 W 21st Street s0sccssesessssseseeees 703 627 6888 Detroit 48234 11360 East Seven Mile Road 00 313 527 5010 Richmond 23222 1424 Chamberlayne Ave s0 703 649 9245 Grand Rapids 49509 3662 Clyde Park Ave S W 616 534 7708 WASHINGTON Seattle 98119 701 Third North 0 0 206 AT 2 6432 MINNESOTA Minneapolis 55408 2815 Nicollet Ave 612 TA3 5283 Spokane 99207 3550 North Market Street PEETA eens 509 HU 9 9164 MISSOURI Kansas City 64108 2705 McGee Trafficway 816 HA 1 1493 WEST VIRGINIA Charleston 25312 1638 Sixth Ave 304 343 0289 St Louis 63110 615 S Vandeventer PCs vow E E 314 JE3 2210 WISCONSIN Milwaukee 53213 6301 Blue Mound Road 414 GR 6 7800 BLACK amp DECKER MFG CO Limited Canada BROCKVILLE ONTARIO 0 00 0 0 te eeescerseeerseanserases Perth Street MONTREAL 10 P Qeiiinccccssdscavesssesin coecasees 7865 St Lawrence Blvd CALGARY ALBERTA 1003 11th Avenue S W OTTAWA ONTARIO PE E Se
5. Box 4305 Highway 301 0 919 425 1181 COLORADO Denver 80204 675 Kalamath St opted 303 222 0621 Greensboro 27403 1008 W Lee Street cesses set haat 919 275 0906 CONNECTICUT Hartford 06114 131 Meadow Street EENEN 203 249 6241 OHIO Cincinnati 45203 1225 Western Ave e 513 421 2275 DISTRICT OF COLUMBIA Washington Cleveland 44113 3901 Detroit AVE cisseereeeessesees ssaesaetes 216 OL 1 4243 Bladensburg Maryland 20710 4501 Baltimore Ries 301 779 3808 Columbus 43202 3293 ee braset seseeeee eee ele cote Falls Church Virginia 22046 129 Annandale Road 703 533 1147 aron ee r E E Ke Eor Solon 44139 6225 Cochran Road cescccceeseeseeeeeees 216 CH 8 5330 FLORIDA Jacksonville 32208 5224 Pearl Street 904 356 2951 Toledo 43606 2629 W Central AVE cssssssessens 419 475 6771 Miami 33168 13345 N W Seventh Avenue 305 681 6658 OKLAHOMA 3106 1318 Li d BI d 405 c Orlando 32806 940 So Orange Ave a T A 305 423 1651 A Oklahoma City 7 inwood Bivd E 2 7515 Tampa 33609 3401 W Kennedy BIVd 0 ccecceeececeeseeseeeee 813 872 8317 Tulsa 74145 3120 South Sheridan ROAG a cicasitiecciceeteaks 918 622 5666 GEORGIA Atlanta 30313 316 Techwood Drive N W 404 JA4 0431 sl a Tu k ae seee pee gt EE arrisburg vi I HAWAI Honotul 96519 675 Auahi SUBAP isst 808 536 9374 Lancaster 17604 715 Fou
6. R MFG CO TOWSON MARYLAND 21204 U S A Form No 97553 cD Printed in U S A z ps didai SE aiai iea SBS ao aii sag En te
7. ease to the amount poige on the Parts List packen with your tool l l It is also recommended that the clutch faces be given a light Refer to exploded parts bulletin included with your tool if you have any difficulty in making the minor disassembly necessary to reach the clutch CLEANING With the tool motor running blow dirt and dust out of all air _ vents with dry air at least once a week Also blow any dirt out of Switches Quick change Chuck or Screw Depth Locator lfyourtool has a Locator it should be disassembled after each day s work and all parts cleaned with kerosene or other cleaning solvent Preferably dry parts with an air hose with the motor running ACCESSORIES Number 12 Scrugun Models can utilize practically every type of fastening accessory bits bit tip holders shanks for sockets etc with a 44 hex shank Your Tool will handle a wide variety of bits and other fastening accessories Some of these are listed below but for the very many other types and sizes of accessories please see your Black amp Decker Distributor or refer to Black amp Decker Catalog No 1 SQUARE DRIVE SHANKS 1 4 HEX DRIVE SHANK No 20510 2 Overall Length For 1 4 Square Drive Sockets 6 Overall Length For 14 Square Drive Sockets No 20511 PHILLIPS HEAD BITS 1 4 HEX DRIVE SHANKS l No 54595 No 1 Point 1 15 16 Overall _ Length No 2
8. ed clutch mechanism and operator pressure on the tool has no effect on output The adjustable clutch mechanism is also provided with a dead spindle so that complete release of pres sure on tool will disengage output spindle To adjust the clutch slide the locking ring toward the gear case This action unlocks the adjusting ring and allows it to be rotated Turning the adjusting ring so that it moves toward the gear case will increase the output torque of the clutch An increase in the force required to turn the adjusting ring indicates that the clutch setting is increasing Turning the ring so that it moves away from the gear case will decrease the clutch setting This is matched with a decrease in effort required to turn the adjusting ring CAUTION Once the adjusting ring is free from spring pressure additional loosen ing has no further effect on the clutch and should be avoided If the adjusting ring is loosened too far it will come off the tool allowing the locking ring and spring also to come off No damage is done and these can be reassembled by operator SPRING MECHANISM DEAD SPINDLE CLUTCH SLIP CLUTCH BT pe es D ADJUSTABLE CLUTCH LUBRICATION Black and Decker Tools are completely lubricated at factory and are ready for use Gears should be relubricated every 60 days to 6 months depending upon use To lubricate remove gear case wipe out old grease and refill gear case with B amp D Heavy Duty Gr
9. ngth of 14 the contemplated length Ampere rating Oto 2 10 to 3 5to 5 10 to 7 10to 12 1 to On nameplate 2 0 7 0 44 120 160 Ext Cable length Wire Size A W G 25 ft 18 18 18 re 75 ft 18 18 16 ae 46925 10 4 4 greasing after every 50 hours of usage OPERATION CLUTCHES In all Black and Decker Scruguns a clutch provides a dead or stationary front spindle to permit the driving accessory to locate the screw slot or nut Forward pressure then engages the clutch and drives the fastener No 12 Scruguns are equipped with either a Positive or Pa Adjustable clutch Operation of these clutches is as follows Positive Clutch With the positive clutch output torque of the screwdriver is directly controlled by operator pressure against the fastener A heavy forward pressure will hold the clutch engaged to a high torque while light forward pressure allows the clutch to disengage at a lower torque Release of pressure completely disengages the clutch Maximum torque on a fastener is reached by maintaining forward pressure on the tool and allowing the clutch to ratchet momentarily the resultant hammering will further tighten the fastener ANGLED JAW CLUTCH POSITIVE CLUTCH Adjustable Clutch tThe adjustable clutch mechanism allows the operator to drive a series of fasteners to a pre set uniform torque Torque output is controlled mechanically by a spring load
10. nnesburg Cape Town Durban South Africa Barcelona Spain Goteborg Sweden Zurich Switzerland Caracas Venezuela DISTRIBUTION CENTERS IFORNI 94804 Richmond 1732 Wright Ave ene Phone 415 235 4232 CONNECTICUT 06051 New Britain 595 John Downey Driv Phone 203 225 8415 GEORGIA Boag Atlanta 3271 Hamilton Blvd SW 4 762 1601 4 ILLINOIS sma Des Plaines 2180 S Wolf Road Phone 3 27 7145 Sales Office 312 827 0083 MARYLAND 21074 Hampstead Phone 301 374 9046 MISSOURI 64116 N Kansas C ity 1343 mntay Drive MANUFACTURING PLANTS Fayetteville North Carolina Lancaster Pa Solon Ohio Towson Md Hampstead Md U S A Brockville Ontario Can Harmondsworth Middx Maidenhead Spennymoor England Croydon Vic Australia Lyon France Milan Italy i BLACK amp DECKER INC Urbanizacion Industrial Julia Phone 816 842 6350 Caparra Heights San Juan Puerto Rico Giarante e BLACK amp DECKER GUARANTEES FOR ONE YEAR FROM DATE OF PURCHASE TO CORRECT BY REPAIR OR PARTS REPLACEMENT WITHOUT CHARGE ANY DEFECT DUE TO FAULTY MATERIAL OR WORKMANSHIP SIMPLY RETURN THE COMPLETE UNIT TRANSPORTATION PREPAID TO ANY BLACK amp DECKER SERVICE CENTER OR AUTHORIZED SERVICE STATION NATURALLY WE ASSUME NO RESPONSIBILITY FOR DAMAGE CAUSED BY MISUSE CARELESS HANDLING OR WHERE REPAIRS HAVE BEEN MADE OR ATTEMPTED BY OTHERS NO OTHER GUARANTEE WRITTEN OR VERBAL IS AUTHORI IZED BY US THE BLACK AND DECKE
11. ntain AVe 1 1 a717 393 5831 ILLINOIS Chicago 60607 1100 W Jackson Blvd 312 TA9 3500 Philadelphia 19103 333 No 20th Street 215 LO 4 5520 het 60646 Lincolnwood 6710 N Crawford Ave 312 OR 3 0923 Pittsburgh 15232 5437 Baur T 412 362 2700 Chicago 60643 Beverly Hills 10708 S Western Ave 312 BE 3 6832 ek ee Rock island 61201 725 30th Street cccscsssssesssess 309 788 1744 RHODE ISLAND E Providence 02914 2777 Pawtucket Ave 401 434 1655 INDIANA Evansville 47708 931 Bond Street 00 812 425 4269 SOUTH CAROLINA Greenville 29601 407 Pendleton St 803 232 3038 Indianapolis 46202 1125 W 16th Street ees 317 632 5569 TENNESSEE Knoxville 37917 1123 North Central St 615 546 2481 E Memphis 38116 984 86 East Brooks Rd 901 332 3444 IOWA Des Moines 50312 2811 Ingersoll AVe 515 CH 4 7257 Na il e 37203 601 Eighth Ave S 615 254 1061 KANSAS Wichita 67214 203 N Mathewson Street 316 FO3 6571 JEXAS Amarillo 79106 3008 West 6th AVe 806 DR 3 1531 KENTUCKY Louisville 40209 4407 Park Blvd 502 366 1495 Dallas 75207 1808 N Industrial Blvd 214 RI 1 6401 LOUISIANA New Orleans 70002 3310 N Causeway Blvd 504 837 2550 Fort Worth 76103 oo Bomar Street saaana E DS at ED 60175 1 203 West 28t ee 301 HO 7 7411 Houston 77 1 ampson Street 09 eaudioesaiee M age S E aa Phas EE E agate 301 485 55
12. pped with approved 3 conductor cord and 3 prong grounding type attachment plug to be used with the proper grounding type receptacle in accordance with the National Electrical Code and Canadian Electrical Code IF YOUR UNIT REQUIRES LESS THAN 150 VOLTS IT HAS A PLUG THAT LOOKS LIKE FIG A It will fit directly into the proper type of 3 wire grounding receptacle The unit is then grounded automatically each time it is plugged in Shown in Fig B is a special grounding adaptor not allowed in Canada by the Canadian Electrical Code which is available from your dealer and will permit using a 2 wire receptacle The green grounding wire extending from the side of the adapter must be connected to a PERMANENT GROUND IF THE UNIT REQUIRES FROM 150 TO 250 VOLTS IT HAS A PLUG LIKE FIGURE C No adapter is available and it should be used in the proper standard matching 3 wire grounding receptacle CABLE The cable is the life line of your tool keep it clean by wiping it off occasionally Keep it out of oils and greases which ruin the rubber Coil it neatly when not in use and avoid dragging it across sharp surfaces or using it as a handle to lift the tool When using the tool at a considerable distance from power source an extension cable of adequate size must be used to prevent loss of power and over heating Use the table below for 115 volt tools For 220 volt tools use wire size corres ponding to an extension le
13. switch is mounted on the top of the tool and for driving fasteners is placed in the forward position To reverse rotation for fastener removal first release trigger to turn tool OFF then move toggle switch back to reverse tool For maximum tool life avoid excessive reverse operation For those operations where the tool is used primarily in reverse see your Black and vecrer Distributor or Black and Decker Service Center MOTOR Your Black and Decker tool is powered by a B amp D built motor Be sure your power supply agrees with nameplate MANNE Volts AC means Alternating Current 25 to 60 cycles ONLY VOLTS AC DC means it will also operate on Direct Current Voltage variation of more than 10 will cause loss of power and over heating All B amp D tools are factory tested if this tool does not operate check the following Supply line for blown fuses plug and receptacle for contact carbon brushes for contact COMMUTATOR AND BRUSHES inspect carbon brushes often Replace when brushes are worn down to the identifying letter or groove or when spring exerts insufficient pressure to hold brush against commutator Keep brushes clean and sliding freely in guides Inspect commutator for dirt and exessive wear If dirty or rough clean lightly with very fine sandpaper not emery cloth If badly worn or _ grooved send tool to our nearest service station for repair sere back page GROUNDING These units are equi
14. th 205 324 6691 NEBRASKA Omaha 68102 2218 Leavenworth Street 402 345 2330 ARIZONA Phoenix 85004 537 E McDowell Rd 602 AL 8 1332 NEW JERSEY Newark 07104 868 Broadway c 00 201 HU 3 1076 ARKANSAS Little Rock 72201 519 West Seventh Street 501 FR 2 3040 NEW MEXICO Albuquerque 87110 4700 Lomas Bivd N E 505 265 6401 CALIFORNIA Anaheim 92802 1235 So Euclid Ave 714 772 4050 NEW YORK Buffalo 14209 881 W Delavan Ave 716 TT 4 6220 Los Angeles 90007 2432 S BrOadWaY ccscecccsssssecssscessees 213 RI 9 0371 New York 10462 1894 E Tremont Avenue Bronx 212 SY 2 2700 Oakland 94606 1107 E 14th St s sseseseoesesesessesrreesscress 415 TE 4 5944 New York 10014 227 Varick St Manhattan 212 WA 9 6450 Sacramento 95814 1915 Seventeenth Street 004 916 444 3188 New York 11377 56 15 Queens Blvd Woodside 212 DE 5 1042 San Diego 92105 3811 El Cajon Blvd AETA 714 AT 1 3331 Rochester 14620 476 Clinton Ave S eseseereresssssrsererrens 454 3814 San ran 7S a pE Airport Blyde ites eae 871 7278 Syracuse 13224 2140 Erie Blvd Eu weccsceesscneeeee 315 446 3086 anta Ciara e PIAMEOTA 0seerseesesoneesensenns BALI NORTH CAROLINA Charlotte 28206 1710 N Graham St 704 FR 5 3721 Van Nuys 91401 14920 Victory Blvd ceseeeseeeeees 213 787 5531 Fayetteville 28306 P O
15. y duty tool 10 WEAR PROPER APPAREL No loose clothing or jewelry to get caught in moving parts Rubber gloves and footwear are recommended when working outdoors 11 USE SAFETY GLASSES with most tools dust mask if cutting operation is dusty 12 DON T ABUSE CORD Never carry tool by cord or yank it to disconnect from receptacle meer cord from heat oil and sharp edges 13 SECURE WORK Use clamps or a vise to hold work It s safer than using your hand and it frees both hands to operate tool 14 DON T OVERREACH Keep proper footing and balance at all times i 15 MAINTAIN TOOLS WITH CARE Keep tools sharp at all times and clean for best and safest performance Follow _ instructions for lubricating and changing accessories 16 DISCONNECT TOOLS When not in use before servicing when changing accessories such as blades bits cutters ete 17 REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on 18 AVOID ACCIDENTAL STARTING Don t carry plugged in 2 tool win finger on switch Also face or s wI TCHE s Pulling the Trigger Switch turns the tool ON AOA the trigger turns the tool OFF To lock switch ON depress trigger hold in locking button and release trigger Release but ton and tool will stay ON To then turn tool OFF depress and release trigger 2 The reversing
Download Pdf Manuals
Related Search