Black & Decker Elu 4029 Instruction Manual
Contents
1. the amount of dust generated b Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils thickness c Sanding should be done ina manner to reduce tracking of paint dust outside the work area ENVIRONMENTAL SAFETY Notes CLEANING AND DISPOSAL a All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project Vacuum filter bags should be changed frequently b Plastic drop cloths should be gathered up and disposed of along with any dust chips or other removal debris They should be placed in sealed refuse receptacles and disposed of through regular trash pick up procedures During clean up children and pregnant women should be kept away from the immediate work area c All toys washable furniture and utensils used by children should be washed thoroughly before being used again Operation First hold the sander off of the work and start motor When the motor comes up to its maximum speed lower the sander onto the work with a slight forward motion Main handle is used to control the sander and the front auxiliary handle to guide it Let the heel or rear drive roller touch the work first bringing the plate into full contact as the stroke moves forward The sander should be moved back and forth parallel to the grain of the wood Fig 5 Don t let the sander stay in one place or the finish will be uneven Short overlapping str2. and so marked STAY ALERT Watch what you are doing Use common sense Do not operate tool when you are tired CHECK DAMAGED PARTS Before further use of the tool a guard or other part that is damaged should be carefully checked to determine that it will operate and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual Have defective switches replaced by authorized service center Do not use tool if switch does not turn it on and off DO NOT OPERATE portable electric tools near flammable liquids or in gaseous or explosive atmospheres Motors in these tools normally spark and the sparks might ignite fumes SAVE THESE INSTRUCTIONS Double Insulation DOUBLE INSULATED tools are constructed throughout with TWO separate layers of electrical insulation or one DOUBLE thickness of insulation between you and the tool s electrical system Tools built with this insulation system are not intended to be grounded As a result your tool is _ equipped with a two prong plug which permits you to use extension cords without concern for maintaining a ground connection NOTE DOUBLE INSULATION does not take the place of normal safety precautions when o
3. total length be sure each individual extension contains at least the minimum wire size To determine the minimum wire size required refer to the chart below CHART FOR MINIMUM WIRE SIZE AWG OF EXTENSION CORDS NAMEPLATE TOTAL EXTENSION CORD LENGTH FEET RATING AMPS 25 75 100 125 150 175 200 O 10 0 18 16 16 14 14 12 12 10 1 13 0 16 14 14 14 12 12 12 13 1 15 0 14 12 12 12 12 12 Before using an extension cord inspect it for loose or exposed wires damaged insulation and defective fittings Make any needed repairs or replace the cord if necessary Switch Your sander starts and stops by depressing and releasing the switch For continuous operation press the lock button located on the side of grip while switch is depressed Depress switch again to release the lock Fig 1 Y Ll Remove the bag and shake the dust out Installing and Changing Abrasive Belt BE SURE YOUR SANDER IS DISCONNECTED FROM POWER SUPPLY WHEN INSTALLING AND CHANGING ABRASIVE BELT AVOID CONTACT WITH THE METAL WEAR PLATE AS IT CAN BECOME QUITE WARM AND THE EDGES CAN BECOME VERY SHARP Before changing the belt switch the beyond the two rollers Then remove the mains plug to prevent the belt sander from starting accidentally Place the machine on its side with the clamping lever 19 pointing upwards release the belt e Pull the belt upwards and out e Insert a new belt over the drive roller an
4. OPERLY Do not wear loose clothing or jewelry They can be caught in moving parts Rubber gloves and non skid footwear are recommended when working outdoors Wear protective hair covering to contain long hair USE SAFETY GLASSES Also use face or dustmask if cutting operation is dusty 10 DON T ABUSE CORD Never carry tool by cord or yank it to disconnect from receptacle Keep cord from heat oil and sharp edges s SECURE WORK Use clamps or a vise to hold work It s safer than using your hand and it frees both hands to operate tool ne DON T OVERREACH Keep proper footing and balance at all times MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safe performance Follow instructions for lubricating and changing accessories Inspect tool cords periodically and if damaged have repaired by authorized service facility Inspect extension cords periodically and replace if damaged Keep handles dry clean and free from oil and grease DISCONNECT TOOLS When not in use before servicing and when changing accessories such as blades bits cutters REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on AVOID UNINTENTIONAL STARTING Don t carry plugged in tool with finger on switch Be sure switch is off when plugging in OUTDOOR USE EXTENSION CORDS When tool is used outdoors use only extension cords intended for use outdoors
5. Pi WOODWORKING TOOLS BY BLACKS DECKER Commercial Industrial Use ee Warranty ELU warrants this product for one year from date of purchase We will repair without charge any defects due to faulty material or workmanship Please return the complete unit transportation prepaid to any Black amp Decker Service Center or Authorized Service Station listed under Tools Electric in the yellow pages This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others Like most Black amp Decker products your tool is listed by Underwriters Laboratories to ensure that it meets stringent safety requirements This symbol on the nameplate means the product is listed by Underwriters Laboratories Inc Instruction Manua Belt Sander WOODWORKING TOOLS BY 4029 BLAG CKER Form No 741394 KAE JULY87 1987 Printed in Switzerland BLACK amp DECKER U S INC U S Power Tools Group 10 North Park Drive P O 798 Hunt Valley MD 21030 0798 U S A 248 315 02 Thanks for buying an ELU Belt Sander Your new ELU belt sander is the serious heavy duty professional tool that you ve been searching for Built to Black amp Decker s traditional standards for quality and toughness your sander will deliver top performance for years to come It flush sands on three sides for getting into corners and includes a dust collecting system for quick cleanup The powerf
6. d belt roller 1 from above making sure that the arrow on the inside of the belt points in the same direction as the Atta C h i ng amp arrow on the sander R e m 0 vi ng D u st e Clamp the belt in position by returning the clamping lever 19 to its original B ag position BE SURE YOUR SANDER IS DISCONNECTED FROM POWER SUPPLY WHEN ATTACHING AND REMOVING DUST BAG The dust bag threads onto the sander with a spring clip 15 To empty the bag it is recommended that it first be removed from the tool The dust collector works best if the bag is emptied more frequently preferably when about 1 3 full machine on and turn the adjusting screw 3 so that the belt projects approximately 2cm e Lift the clamping lever 19 upwards and Tracking Adjustment Wear Eye Protection Turn the machine upside down hold it firmly with one hand start motor and release switch immediately after observing tracking of sanding belt If abrasive belt runs outward turn tracking adjustment screw clockwise and counterclockwise if belt runs inward Fig 4 Adjust the belt until the outer edge of the belt is even with the outer edge of both front and rear rollers Also check that the belt doesn t rub against belt guide strip Belt life will be greatly increased by keeping the tracking adjustment properly set
7. ntenance and adjustment including brush inspection and replacement should be performed by qualified service organizations always using ELU replacement parts ELU products are serviced by Black amp Decker Company owned Service Centers Important Safety Instructions WARNING When using Electric Tools basic safety precautions should always be followed to reduce risk of fire shock and personal injury including the following gt wo N Ti 12 13 14 15 16 17 18 T9 20 READ ALL INSTRUCTIONS KEEP WORK AREA CLEAN Cluttered areas and benches invite injuries CONSIDER WORK AREA ENVIRONMENT Don t expose power tools to rain Don t use power tools in damp or wet locations Keep work area well lit GUARD AGAINST ELECTRIC SHOCK Prevent body contact with grounded surfaces For example pipes radiators ranges refrigerator enclosures KEEP CHILDREN AWAY All visitors should be kept away from work area Do not let visitors contact tool or extension cord STORE IDLE TOOLS When not in use tools should be stored in dry and high or locked up place out of reach of children DON T FORCE TOOL It will do the job better and safer at the rate for which it was intended _ USE RIGHT TOOL Don t force small tool or attachment to do the job of a heavy duty tool Don t use tool for purpose not intended for example don t use circular saw for cutting tree limbs or logs DRESS PR
8. okes produce the best results When sanding avoid tilting the machine sideways as belt will make a deep cut into the work The weight of the machine itself is sufficient and extra pressure will only result in an uneven finish Don t force tool allow the machine to work easily Use the coarse grit abrasive belt for fast sanding and finer grit for finishing Maintenance BE SURE YOUR SANDER IS DISCONNECTED FROM POWER SUPPLY Clean accumulated dust from your sander after each workpiece is finished When doing maintenance take care that oil or water doesn t come into contact with the motor Accessories Black amp Decker offers a wide array of sanding belts and other accessories to enhance the versatility of your sander Visit your local Black amp Decker Service Center where recommended accessories can be purchased see fig 6 7 If you need assistance in locating recommended accessories for your tool contact Black amp Decker U S Inc User Services Department 10 North Park Drive P O Box 857 Hunt Valley MD 21030 0857 Recommended accessories for your tool are available at extra cost from your local Black amp Decker Service Center The use of any other accessories or attachments may be hazardous If you have any questions concerning which accessories are recommended contact Black amp Decker at the above address Important To assure product SAFETY and RELIABILITY repairs mai
9. perating this tool The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool CAUTION When servicing all tools USE ONLY IDENTICAL REPLACEMENT PARTS Repair or replace damaged cords Extension Cords Motor Your ELU tool is powered by an ELU built motor Be sure your power supply agrees with the nameplate marking Volts 50 60 Hz or AC only means your tool must be operated only with alternating current and never with direct current Voltage decrease of more than 10 will cause loss of power and overheating All ELU tools are factory tested if this tool does not operate check the power supply Double insulated tools have 2 wire cords and can be used with 2 wire or 3 wire extension cords Only round jacketed extension cords should be used and we recommend that they be listed by Underwriters Laboratories U L If the extension will be used outside the cord must be suitable for outdoor use Any cord marked as outdoor can also be used for indoor work The letters WA on the cord jacket indicate that the cord is suitable for outdoor use An extension cord must have adequate wire size AWG or American Wire Gauge for safety and to prevent loss of power and overheating The smaller the gauge number of the wire the greater the capacity of the cable that is 16 gauge has more capacity than 18 gauge When using more than one extension to make up the
10. ul f i WOODWORKING TOOLS BY BLACKS DECKER motor and large sanding surface make short work of the toughest jobs Please take the time to thoroughly read this instruction manual and pay particular attention to the safety rules we ve provided for your protection Don t forget to send in your owner s registration card Thanks agains for buying Black amp Decker Precautions To Take When Sanding Paint 1 Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the contaminated dust The greatest danger of lead poisoning is to children and pregnant women 2 Since it is difficult to identify whether or not a paint contains lead without a chemical analysis we recommend the following precautions when sanding any paint PERSONAL SAFETY a No children or pregnant women should enter the work area where the paint sanding is being done until all clean up is completed b A dust mask or respirator should be worn by all persons entering the work area The filter should be replaced daily or whenever the wearer has difficulty breathing c NO EATING DRINKING or SMOKING should be done in the work area to prevent ingesting contaminated paint particles Workers should wash and clean up BEFORE eating drinking or smoking Articles of food drink or smoking should not be left in the work area where dust would settle on them a Paint should be removed in such a manner as to minimize
Download Pdf Manuals
Related Search