Black & Decker PW1300 User's Manual
Contents
1. cy V Hz correspond to those specified on the appliance data plate fig 2 The appliance should only be connected to a mains power supply equipped with an adequate earth connection and a differential security breaker 30 mA to cut off the electricity supply in the instance of a short circuit 5 3 1 Use of extension cables Use cables featuring IPX5 protection level The cross section of the extension cable should be pro portionate to its length the longer it is the greater its cross section should be See table Water supply connection Caution Danger Only clean or filtered water should be used for intake The delivery of the water intake tap should be equal to that of pump capacity Place the appliance as close to the water supply system as possible 5 4 1 Connection points Water outlet OUTLET M Water inlet with filter INLET Connection to the mains water supply The appliance can be connected directly to the mains drinking water supply only if the supply hose is fitted with a backflow preventer valve as per current regulations in force Make sure that the hose is at least 13 mm and that it is reinforced 5 4 2 English 13 RER ADJUSTMENT INFORMATION FIG 3 6 1 6 2 6 3 6 4 Adjusting the spray nozzle for models with this feature Water flow is adjusted by regulating the nozzle E Adjusting the detergent on models with this feature Detergent flow is adjusted using the regulator F Adjusting2. anti clockwise exchange two of the three phase wires L1 L2 L3 in the electrical plug 1 Turn on the water supply tap fully 2 Release the safety catch D 3 Depress the gun trigger for a few seconds and start up the appli ance using the starter device ON 1 TSS models In TSS models with automatic delivery flow cut off system when the gun trigger is released the dynamic pressure automati cally cuts out the motor see fig 4 when the gun trigger is depressed the automatic drop in pres sure starts the motor and the pressure is restored after a very slight delay if the TSS is to function correctly all gun releasing and depress ing operations must be performed at intervals of less than 4 5 seconds To prevent damage to the appliance when running do not stop the water jet for more than 10 minutes at a time Stopping the appliance 1 Set the starter device switch on OFF 0 2 Depress the gun trigger and discharge the residual pressure inside the hoses 3 Engage the gun safety catch D 74 75 7 6 1 7 Restarting 1 Release the safety catch D 2 Depress the gun trigger and discharge the residual air inside the hoses 3 Set the starter device on ON 1 Storage 1 Switch the appliance off OFF 0 2 Remove the plug from the socket 3 Turn off the water supply tap 4 Discharge the residual pressure from the gun until all the water has come out of the nozzle 5 Drain the d
3. the detergent pressure Set the adjustable nozzle on EE to deliver detergent at the correct pressure on models with this feature Adjusting the pressure on models with this feature The regulator G is used to adjust the working pressure The pres sure is shown on the pressure gauge where fitted INFORMATION ON USE OF THE APPLIANCE FIG 4 71 72 73 Controls Starter device H Set the starter switch on ON 1 to a start the motor in models without TSS device b set the motor ready to start in models with TSS device If there is a pilot light on the starter device it should light up If the low high settings are available use them as follows Low low pressure washing High high pressure washing Set the starter device switch on OFF 0 to shut down the applian ce If there is a pilot light on the starter device it should go out Water jet control lever I Caution Danger During operation the appliance must be positioned as shown in fig 4 on a sturdy stable surface Start up Caution Danger Before starting up the appliance check that the water supply hose is connected properly use of the appliance without water will damage it do not cover the ventilation grilles when the appliance is in use On three phase models for professional use at first use start the appliance for a very short time to check that the motor is running in the correct direction If the motor fan is turning
4. ZARD 2 1 15 Make sure that cars do not drive over the high pressure hose 2 2 SAFETY MUSTS 2 2 1 A Allelectrical conductors MUST BE PROTECTED against the water jet SHORT CIRCUIT HAZARD 222 A The appliance MUST ONLY BE CONNECTED to an adequate power supply in compliance with all applicable regulations ELECTRIC SHOCK HAZARD Use of a safety residual current circuit breaker R C C B will provide additional protection for the operator 30 mA 2 2 3 NER QO high pressure may cause materials to bounce off surfaces at speed therefore protective clothing and safety goggles MUST BE WORN INJURY HAZARD 2 2 4 Before doing work on the appliance REMOVE the plug ACCIDENTAL START UP HAZARD 2 2 5 A Before pressing the trigger GRIP the gun firmly to counteract the recoil INJURY HAZARD 2 2 6 COMPLY WITH the requirements of the local water supply company According to DIN 1988 the appliance may only be connected to the mains drinking water supply if a backflow preventer valve with drain facility is installed in the supply hose CONTAMINATION HAZARD A Maintenance and or repair of electrical components MUST be carried out by qualified staff ACCIDENT HAZARD A DISCHARGE residual pressure before disconnecting the unit hose INJURY HAZARD 2 29 A Before using the appliance CHECK every time that the screws are fully tightened and that there are no broken or worn parts ACCIDENT HAZARD 2 2 10 AM A ONLY USE detergents which
5. blackanddecker eu q cod 90968 GX r Lire ce manuel avant l installation utilisation du nettoyeur en faisant tr s attention aux INSTRUCTIONS POUR LA S CURIT Read this manual through carefully before installing using the cleaner paying special attention to the SAFETY INSTRUCTIONS Lesen Sie dieses Handbuch vor der Installation und dem Gebrauch des Hochdruckreinigers aufmerksam durch und achten Sie besonders auf die SICHERHEITSANWEISUNGEN Leggere questo manuale prima dell installazione uso dell idropulitrice prestando particolare attenzione alle ISTRUZIONI PER LA SICUREZZA Leer este manual antes de la instalaci n uso de la hidrolimpiadora prestando particular atenci n a las INSTRUCCIONES SOBRE SEGURIDAD Leia este manual antes de instalar usar a lavadora a alta press o prestando muita aten o nas INSTRU ES PARA A SEGURAN A AlaBdote ro rap v Eyxeipi lo TrpIv AT TNV EyKkat otaon xpnon Tou UNXAV HATO TA ONG HE I LA TEPN MPODOX OTIC OAHTIEX TIA THN AZOAAEIA Lees v r de installatie het gebruik van de hogedrukreiniger deze handleiding goed door en in het bijzonder de VEILIGHEIDSVOORSCHRIFTEN Les denne vejledning inden installation og brug af hojtryksrenseren og veer s rligt opm rksom p SIKKERHEDSREGLERNE Les denne h ndboken for installasjon og bruk av hoytrykksspyleren og v r spesielt oppmerksom p SIKKERHETSREGLENE Lue t m k ytt opas ennen painepesurin asennusta k ytt Kiinnit er
6. ce in models with this feature fig 5 Have the seals replaced at your nearest Authorized Service Centre Appliance noisy Water too ho Reduce temperature see technical data Oil leakage Seals worn Contact your nearest Authorized Service Centre Appliance not used for a long period of time Water leakage Seals worn Nozzle clogged Clean nozzle fig 5 TSS versions only motor starts even with gun trigger is released High pressure system or pump hydraulic circuit not watertight Contact your nearest Authorized Service Centre TSS versions only no water deliv ery when gun trigger is depressed Nozzle clogged Clean nozzle fig 5 with supply hose connected If the motor starts and does not restart during operation wait 2 3 minutes before repeating the start up procedure overload cutout has been tripped If the problem recurs more than once contact your nearest Authorized Service Centre CE DECLARATION OF CONFORMITY EN We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents EN 60335 1 EN 60335 2 79 EN 55014 1 EN 55014 2 EN 61000 3 2 EN 61000 3 3 EN 61000 3 11 EN 60704 1 In accordance with the regulations 98 37 CE 2006 95 CE 2002 95 CE 2002 96 CE 2004 108 CE 2000 14 CE Date 23 01 2008 MODENA I Stefano Reverberi Managing Director
7. etergent tank 6 Engage the gun safety catch D Refilling and using detergent When using detergent the adjustable nozzle must be set on EB on models with this feature Fill the tank with highly degradable detergent Recommended cleaning procedure Dissolve dirt by applying the detergent mixed with water to the surface while still dry When dealing with vertical surfaces work from the bottom upwards Leave the detergent to act for 1 2 minutes but do not allow the surface to dry Starting from the bottom use the high pressure jet ata minimum distance of 30 cm Do not allow the rinse water to run onto unwashed surfaces HEN MAINTENANCE FIG 5 8 1 8 2 8 3 8 4 Any maintenance operations not covered by this chapter should be carried out by an Authorized Sales and Service Centre Caution Danger Always disconnect the plug from the power socket before carrying out any work on the appliance Cleaning the nozzle 1 Disconnect the lance from the nozzle 2 Remove any dirt deposits from the nozzle hole using the tool C1 Cleaning the filter Clean the suction filter L and the detergent filter after every 50 hours of operation Unjamming the motor on models with this feature In case of lengthy stoppages limescale sediments may cause the motor to seize To unjam the motor turn the drive shaft with a tool M End of season storage Treat the appliance with non corrosive non toxic antifreeze before storing
8. iginal spare parts and any other spare parts not specifically intended for the model in question is prohibited All modifications to the appliance are prohibited Any modifications made to the appliance shall render the Declaration of Conformity null and void and relieve the manufacturer of all liability under civil and criminal law Main components B1 Adjustable spray nozzle 45 B2 Lance B3 Gun with safety catch B4 Power supply cable with plug B5 High pressure hose B6 Detergent tank on models with this feature Accessories where applicable see fig 1 C1 Nozzle cleaning tool C2 Rotating nozzle kit C3 Handle C4 Brush C5 Hosereel Safety devices Caution Danger Do not tamper with or adjust the safety valve set ting Safety valve and pressure limiting valve The safety valve is also a pressure limiting valve When the gun trigger is released the valve opens and the water recirculates through the pump inlet Safety catch D prevents accidental spraying of water INSTALLATION FIG 2 5 1 5 2 5 3 5 4 Assembly Caution Danger All installation and assembly operations must be performed with the appliance disconnected from the mains power supply The assembly sequence is illustrated in fig 2 Assembling the rotating nozzle For models with this feature The rotating nozzle kit delivers greater washing power Electrical connection Caution Danger Check that the electrical supply voltage and frequen
9. it away for winter 14 English EJ TRouBLESHOOTING D Nozzle worn Replace nozzle Water filter fouled Clean filter fig 5 Water supply pressure low Turn on water supply tap fully Pump does not reach working Air being sucked into system Check tightness of hose fittings pressure Switch off the appliance and keep depressing and releas Air in pump ing the gun trigger until the water comes out in a steady flow Switch the appliance back on again Adjustable nozzle not positioned correctly Turn the adjustable nozzle E fig 3 Water intake from external tank Connect appliance to the mains water supply Pressure drops during use Intake water too hot Reduce temperature Nozzle clogged Clean nozzle fig 5 Check that the voltage of the mains power supply line is the same as that on the plate fig 2 Motor sounds but fails to start Voltage loss due to use of extension cable Check characteristics of extension cable Insufficient power supply Appliance not used for a long period of time Contact your nearest Authorized Service Centre Problems with TSS device Contact your nearest Authorized Service Centre Check that the plug is firmly in the socket and that the mains voltage supply is present No electrical power Motor fails to start Problems with TSS device Contact your nearest Authorized Service Centre Using the tool L unjam the motor from the hole at the rear of the applian
10. ityist huomiota TURVAOHJEISIIN L s igenom bruksanvisningen f re installation och anv ndning av h gtryckstv tten L gg speciellt m rke till S KERHETSBEST MMELSERNA P ed instalac nebo pou v n m tohoto isti e si pe liv p e t te tuto p ru ku Zv enou pozornost v nujte sti BEZPE NOSTN POKYNY Przed przyst pieniem do instalacji b d u ycia myjki nale y dok adnie przeczyta niniejszy podr cznik zwracaj c szczeg ln uwag na tre cz ci dotycz cej INSTRUKCJI BEZPIECZE STWA Pozorno preberite ta navodila pred namestitvijo uporabo istilnika pri emer posebno pozornost namenite VARNOSTNIM NAVODILOM Pred in tal ciou pou van m isti a si pozorne pre tajte tento n vod a budte obzvl opatrn pri tan BEZPE NOSTN CH POKYNOV Prie sumontuodami ir naudodami jrenginj atid iai perskaitykite Sig naudojimo instrukcij ypating demesj atkreipdami SAUGOS INSTRUKCIJAS Mpoyememe mosa poxogodcmeo emumamenho npedu da uncmanupame u3non3eame mauluHama 3a noyucmeane kamo o6bpHeme oco6eno eHumaHue Ha VHCTPYKLIMUTE 3A BESOMACHOCT Mpouuma me daHHoe Pykosodcmeo neped ycmaHoskol moeyHo mauuHbi o6paw aa ocobeHHoe BHUMAHUE Ha UHCTPYKLUN MO BE3BOTIACHOCTU Atisztit berendez s zembehelyezese haszndlata el tt olvassa dt gondosan ezt a le r st k l n s figyelmet szentelve a BIZTONS GI EL R SOK c m r sznek Cititi acest manual n ntregime cu aten ie nainte de a in
11. stala utiliza aparatul de cur at acord nd o aten ie m rit INSTRUC IUNILOR DE SIGURAN Hidro temizleyiciyi kurmadan kullanmadan nce EMN YET B LG LER NE zellikle dikkat g stererek i bu k lavuzu okuyunuz Prije montiranja kori tenja ista a pa ljivo pro itajte ovaj priru nik i posebnu pozornost posvetite SIGURNOSNIM MJERAMA Pirms t r anas ier ces uzst d anas izmanto anas izlasiet o rokasgr matu pa i v r gi lasiet DRO BAS NOTEIKUMUS LS IESO RE FE A 25 500 2x 2 5 mm Switch Z1 Capacitor suppressor T Thermal protection M Motor S1 Pressure switch English 11 EM SAFETY INSTRUCTIONS 1 1 The appliance you have purchased is a technologically advanced product designed by one of the leading European manufacturers of high pressure pumps To obtain the best performance from your unit read this booklet carefully and follow the instructions each time you use the it We congratulate you on your choice and wish you successful operation BA sarery RULES 2 1 SAFETY MUST NOTS 2 1 1 AM AE DO NOT use the appliance with inflammable or to
12. will not corrode the coating materials of the high pressure hose electrical cable EXPLOSION AND ELECTRIC SHOCK HAZARD 2 2 11 A ENSURE that all people or animals keep a minimum distance of 16 yd 15m away INJURY HAZARD 12 3 1 3 2 3 3 3 4 English GENERAL INFORMATION FIG 1 Use of the manual This manual forms an integral part of the appliance and should be kept for future reference Please read it carefully before installing using the unit If the appliance is sold the Seller must pass on this manual to the new owner along with the appliance Delivery The appliance is delivered partially assembled in a cardboard box The supply package is illustrated in fig 1 3 2 1 Documentation supplied with the appliance AT Use and maintenance manual A2 Safety instructions A3 Declaration of conformity Disposing of packaging The packaging materials are not environmental pollutants but must still be recycled or disposed of in compliance with the relevant legislation in the country of use Safety signs Comply with the instructions provided by the safety signs fitted to the appliance Check that they are present and legible otherwise fit replacements in the original positions E1 sign Indicates that the appliance must not be disposed of as municipal waste it may be handed in to the dealer on purchase of a new appliance The appliance s electrical and electronic parts must not be reused for improper uses since the
13. xic liquids or any products which are not compatible with the correct operation of the appliance EXPLOSION OR POISONING HAZARD 2 1 2 AK DO NOT direct the water jet towards people or animals INJURY HAZARD 2 1 3 A Ri DO NOT direct the water jet towards the unit itself electrical parts or towards other electrical equipment ELECTRIC SHOCK HAZARD 2 1 4 DO NOT use the appliance outdoors in case of rain SHORT CIRCUIT HAZARD 2 1 5 DO NOT allow children or incompetent persons to use the appliance INJURY HAZARD 2 1 6 AY DO NOT touch the plug and or socket with wet hands ELECTRIC SHOCK HAZARD 2 1 7 A DO NOT use the appliance if the electrical cable is damaged ELECTRIC SHOCK AND SHORT CIRCUIT HAZARD 2 1 8 AM DO NOT use the appliance if the high pressure hose is damaged EXPLOSION HAZARD 2 1 9 A DO NOT jam the trigger in the operating position ACCIDENT HAZARD 2 1 10 A Check that the data plates are affixed to the appliance if not inform your dealer Units without plates must NOT be used as they are unidentifiable and potentially dangerous ACCIDENT HAZARD m DO NOT tamper with or alter the calibration ofthe MEL valve EXPLOSION HAZARD 2 1 11 2 1 12 DO NOT alter the original diameter of the spray head nozzle HAZARDOUS ALTERATION OF OPERATING PERFORMANCE 2 1 13 A DO NOT leave the appliance unattended ACCIDENT HAZARD 2 1 14 DO NOT move the appliance by pulling on the ELECTRICAL CABLE SHORT CIRCUIT HA
14. y contain substances which constitute health hazards 3 4 1 Symbols E2 symbol Indicates that the appliance is intended for professional use i e for experienced people informed about the relative technical regulatory and legislative aspects and capable of performing the operations neces sary for the use and maintenance of the appliance E3 symbol Indicates that the appliance is intended for non professional domestic use TECHNICAL INFORMATION FIG 1 41 42 43 44 Envisaged use This appliance has been designed for individual use for the cleaning of vehicles machines boats masonry etc to remove stubborn dirt using clean water and biodegradable chemical detergents Vehicle engines may be washed only if the dirty water is disposed of as per regulations in force Intake water temperature see data plate on the appliance Intake water pressure below 10 bar Operating ambient temperature above 0 C The appliance is compliant with the EN 60335 2 79 A1 standard Operator The symbol on the front cover identifies the appliance s intended operator professional or non professional Improper use Use by unskilled persons or those who have not read and under stood the instructions in the manual is forbidden The introduction of inflammable explosive and toxic liquids into the appliance is prohibited Use of the appliance in a potentially inflammable or explosive atmosphere is forbidden The use of non or
Download Pdf Manuals
Related Search