Berkel B32 User's Manual
Contents
1. repairs pursuant to this warranty Berkel expressly excludes responsibility for incidental or consequential damages to buyer or any third party including without limitation damages arising from personal injuries lost profits loss of business opportunity loss of property economic losses or statutory or exemplary damages whether in negli gence warranty strict liability or otherwise This warranty does not apply to periodic maintenance of equipment including but not limited to lubri cation replacement of worn blades knives stones knobs accessories and miscellaneous expendable supply items and other adjustments required due to installation set up or normal wear These warranties are given only to the first purchaser from a Berkel Authorized Channel of Distribution No warranty is given to subsequent transferees The foregoing warranty provisions are a complete and exclusive statement of the warranty between the buyer and seller Berkel neither assumes nor authorizes any persons to assume any other obligation or liability connection with said equipment This warranty supersedes any and all prior warranties to the subject hereof Model 180 slicers carry a 90 day warranty Three year replacement guarantee for polymer parts used on the X series slicers BK46708 September 2007 162. the feeder clockwise as far as it will go and 1s firmly in posi tion Then check that the machine stops when the feeder handle 1s raised and restarts when the feeder handle is lowered with the variable speed control in the T IP or P positions Set the variable speed control to position II and then lift the feeder handle and check that the shaft stops rotating within 4 seconds Safety check before processing with the bowl First remove the lid the knife and the bowl in ac cordance with the instructions under the heading Removing the Bowl and then check that the machine will not start when the variable speed control is in the T II or P positions Install the bowl and lid but not the knife in accordance with the instructions under the heading Installing the Bowl and set the variable speed control to the II position Remove the lid by turning it counterclockwise and check that the shaft stops rotating within 4 seconds In the event of any fault or malfunction call in an authorized service technician to correct the fault be fore using the machine Continuous Feed Operation l The Continuous Feed attachment is used together with a suitable cutting tool for slicing dicing shredding or grating The large feed compartment is used mainly for feeding potatoes onions peppers etc and cutting larger foods such as cabbage The large feed compartment is also used when the food has t
3. 2 3 4 Turn the feeder counterclockwise as far as it will go then lift off the feeder Turn the cutting tool clockwise and lift it off Lift off the dicing grid 1f applicable Lift off the ejector plate Bowl Processing l The bowl is used for chopping and grinding or for blending mixing etc Amount Size and Processing Times of Foods When Processing With the Bowl l The amount and size of the pieces which can be processed at one time and the length of time the processing takes depend on the consistency of the foods and on the result desired VA For even and consistent results with firm foods such as meat and cheese it should first be sepa rated into pieces approximately equal in size and not bigger than 1x1x1 in 3x3x3 cm 3 The maximum amounts which should be processed at one time Meat 2 Ib Fish 2 Ib Aromatic butter 2 Ib Mayonnaise 2 pints Parsley 1 8 pints Installing the Bowl l Place the bowl on the machine base so that the locating plate of the bowl is inserted into the recess on the top of the machine base VA Place the knife on the shaft and rotate the knife while pressing it down so that it drops complete ly onto its coupling ibi Fit the sealing ring into the groove on the inside of the lid 4 Grip the center of the scraper ring and place the lid on the scraper ring Di Place the scraper handle on top of the lid and press together the scraper ring and the scraper handle while at the sa
4. 70 in Materials les The machine base is made of aluminium 2 The continuous feed attachment e Housing Polycarbonate Ejector plate Acetal e Cutting tool discs Robust acetal polysulphone polyutherane or aluminium Cutting tool blades Stainless Steel 3 The bowl cutter mixer attachment e Bowl Stainless Steel Knife hub Acetal e Knife blades Stainless Steel e Lid Polycarbonate Scraper Polysulfone Net Weights I Machine base 20 0 Ibs Vegetable preparation attachment complete but excluding cutting tools 2 2 Ibs Cutting tools approx 0 9 Ib average i 2 Fast chopping attachment complete but excluding knife 3 0 Ibs _ 14 OPTIONAL CCESSORIES LAR Berkel The Choice of Experience WARRANTY Effective February 14 2002 Berkel Company Berkel warrants to the Buyer of new equipment that said equipment when installed in accordance with our instructions and subjected to normal use is free from defects in material or work manship for a period of one 1 year from the date of sale BERKEL SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Berkel s obligation and liability under this warranty is expressly limited to repairing or replacing equip ment that proves to be defective in material or workmanship within the applicable warranty period Berkel or a Designated Berkel Service Location will perform all
5. Berkel The Choice of Experience NOTICIA IMPORTANTE Este manual contiene importantes instrucciones de seguridad que deben ser seguidas el pie de la letra cuando utilice esta maquina OWNER OPERATOR MANUAL MODELS CC34 C32 B32 FooD PROCESSORS IMPORTANT NOTICE This manual contains Important Safety Instructions which must be strictly followed when using this equipment BK46708 September 2007 BEFORE USING THIS EQUIPMENT Berkel s Food Processors are designed to process fruits vegetables and other food products safely and efficiently However unless the operator 1s properly trained and supervised there is the possibility of a serious injury It is the re sponsibility of the owner to ensure that this food processor is used properly and safely strictly following the instructions contained in this manual and any requirements of local law No one should use or service this food processor without proper training and supervision All operators should be thoroughly familiar with the procedures contained in this manual Even so Berkel cannot anticipate every circum stance or environment in which its food processors will be used You the owner and or operator must remain alert to the hazards posed by the function of a food processor particularly the sharp cutting tools No one under 18 years of age should operate this equipment If you are uncertain about a par ticular task ask your supervisor This manual cont
6. GRO INSTRUCCIONES GENERALES DE SEGURIDAD NUNCA utlice esta mequina sin previa instrucci n y autorizaci n de su supervisor LA M QUINA DEBE apoyarse sobre un nivel solido y plano SIEMPRE utilice el enchufe original proveldo por el fabricante SIEMPRE utilice el utensillo para empujar la comida nunca su mano NUNCA TOQUE LA HERRAMIENTA DE CORTO MANTENGA manos brazos cabello y ropa suelta LEJOS de toda parte en movimiento de la m quina EN CASO DE QUE LA M QUINA SE TRABE apague y desconecte ANTES de sacar lo que la obstruye APAGUE Y DESCONECTE LA M QUINA antes de limpiar sanitizar o arreglar UTILIZE UNICAMENTE los repuestos provistos por el fabricante EN CASO de que los membretes de PELIGRO se desprendan de la mequina o sean illegibles llame al fabricante o a su representante de service Berkel para que lo reemplace sin cargo 44 WARNING GENERAL SAFETY INSTRUCTIONS NEVER touch this machine without training and authorization by your supervisor MACHINE MUST BE on solid level support ALWAYS use three pronged plug provided ALWAYS use food pusher not your hand NEVER TOUCH CUTTING TOOL KEEP hands arms hair and loose clothing clear of all moving parts SHOULD MACHINE JAM turn off and unplug before removing obstruction TURN OFF AND UNPLUG machine from power source before cleaning sanitizing or servicing USE ONLY the attachments provided by the manufacturer SHOULD any warning label on a ma
7. ains a number of safe practices in the General Safety Instruc tion Section Additional warnings are placed throughout this manual WARN INGS RELATED TO YOUR PERSONAL SAFETY ARE INDICATED BY A WARNING If any warning label wall chart or manual becomes misplaced damaged or illegible please contact your nearest distributor or Berkel directly for a free replacement Remember however THIS MANUAL OR THE WARNING LABELS DO NOT REPLACE THE NEED TO BE ALERT AND TO USE YOUR COMMON SENSE WHEN USING THIS FOOD PROCESSOR TABLE OF CONTENTS Before Using This Equipment ener 2 Instrucciones Generales de Seguridad 4 General Safety Instructions 4 Equipment Description 5 Intended Uses and Characteristics 7 Unpacking and Installation 7 OST ADO Mis nssecsrctececcasessaatcnacvnieasvenncounriseaniesausiieacamesteasseceas 8 Udo 11 Troubleshooting renen erere nerne renee 11 SPEC 12 Optional ACCESSOrIES senere rer nnrnree 15 WATTAD O tratos pe n 16 The Berkel Company World s Leading Manufacturer of Slicers and Food Processing Equipment BERKEL COMPANY 4406 Technology Drive South Bend Indiana 46628 9770 574 232 8222 Fax 888 888 2838 800 348 0251 Printed in USA Berkel Company Part No 3175 00944 a ses SE Un in a 5 Se I CS A 44 PELI
8. ator protection e Carrying handles for ease of transport e Two handed filling for maximum throughput e Automatic start stop functions on feeder UNPACKING AND INSTALLATION NOTE Immediately after unpacking check the unit for shipping damage If the unit is found to be dam aged save everything Notify the carrier within 5 days of delivery l Place the machine on a sturdy bench or table 26 35 inches high DA Connect the machine to a main electric supply with specification in accordance with the details on the data plate on the back of the machine base 3 Mount the wall rack 1f available for the cutting tools and the ejector plate on a wall close to the machine 7 To eliminate a potential shock hazard a properly grounded outlet using the three pronged plug provided must power this unit Before plugging the food processor in check your outlet voltage to be sure it complies with the voltage specified on the serial number plate on the food processor OPERATION General l Safety check before processing with the feeder Remove the feeder any cutting tools and the ejector plate in accordance with the instructions under the heading Removing the Feeder and then check that the machine will not start when the variable speed control is in the T Il or P positions Place the feeder on the machine base with the text Close Open at 5 o clock in relation to the outlet of the machine base and turn
9. chine come off or become unreadable contact the manufac turer or your Designated Berkel Service Location for a free replacement Wo FE Feed Tube Large Feed Compartment Pusher Standard Slicer Crimping Slicer Fine Cut Slicer Julienne Cutter Dicing Grid Grater Shredder e DN Fine Grater EQUIPMENT DESCRIPTION Feeder Handle Machine Outlet Variable Speed Shaft Control Machine Handle Base Scraper Handle Lid Scraper Ring Knife Bowl Always Use Ejector Plate Assemble Sealing Ring Into Lid Price eg MEN Dismantling Lid Assembling Bowl Assembling Feeder Unit INTENDED USES AND CHARACTERISTICS Intended Uses The Models CC34 C32 and B32 Food Processors are designed for the following applications e Slices dices shreds and or grates fruits vegetables dry bread cheese and nuts e Chops and grinds meat fish fruits vegetables and nuts e Blends Mixes sauces aromatic butter mayonnaise soups dressings thickenings desserts etc The following types of items are NOT suitable for processing in the Models CC34 C32 and B32 e Non food items e Frozen foods Bone in products Special Features Characteristics e Two or four speeds Auto select on CC34 for perfect processing results during cutting amp chopping e Low profile compact design for easy product loading e Pulse function and scraper save time during cutting e Dual interlocks for oper
10. me time turning the scraper handle counterclockwise as far as it will go so the three parts are Joined 6 Place the lid on the bowl so that the text Close Open is at 5 o clock in relation to the outlet of the machine base F Turn the lid clockwise as far as it will go Removing the Bowl I Turn the lid counterclockwise as far as it will go and lift away the lid scraper Ze To disassemble the scraper from the lid press the scraper ring and the scraper handle together while rotating the scraper handle clockwise as far as it will go and separate the three parts Sy Rotate the knife clockwise as far as it will go remove the knife and lift off the bowl If the con tents of the bowl are liquid it should be emptied before the knife is removed Using the Variable Speed Control l During dicing and slicing of fragile foods such as tomatoes peppers etc it is recommended that the variable speed control is set in the I position to give extra slow gentle processing and the best results 10 SE D With the variable speed control in the O position the machine is switched off In the I posi tion the machine operates continuously at low speed In the II position the machine operates continuously at high speed In the P pulse position the machine operates at high speed until the variable speed control is released CLEANING Always clean the machine thoroughly immediately after use First s
11. o be cut sliced in a specific direction e g when slicing tomatoes and lemons The feed tube is mainly used in connection with processing elongated foods such as cucumbers Choice of Cutting Tools When Processing With the Feeder I 2 3 Slicer Slices soft and firm foods Dices in combination with the Dicing Grid Crimping Slicer For ripple slicing Julienne Cutter For julienne potatoes cucumber etc 3 16 x 3 16 in 4 5 x 4 5 mm for shred ding of white cabbage Dicing Grid Dices in combination with the standard slicer Grater Shredder Grates carrots white cabbage nuts cheese dry bread etc Fine Grater Finely grates raw potatoes hard dry cheese etc Installing the Feeder l 2 Place the ejector plate on the shaft and turn press down the ejector plate onto its coupling During dicing place the dicing grid with the sharp edge of the knives upward so that the recess in the side of the dicing grid fits into the guide grove on the machine base Then place the standard slicer so that it drops down onto its coupling During slicing shredding and grating place only the chosen cutting tool on the shaft and rotate the cutting tool so that it drops onto its coupling Place the feeder on the machine base so that the text Close Open is at 5 o clock in relation to the outlet of the machine base and turn the feeder clockwise as far as it will go and it is firmly in position Removing the Feeder l
12. rcuit breaker in the electrical panel to see if it has tripped Check that the feeder is correctly installed and that the feeder handle has been lowered Check that the bowl and lid are correctly installed Wait for up to 30 minutes and then try to start the machine again Call in a service technician for further action Low Capacity or Poor Processing Results When Using the Feeder l 2 3 4 Select the right cutting tool or combination of cutting tools Always use the ejector plate Check that the knives and slicing discs are sharp and without any defects Press the food down loosely Low Capacity or Poor Processing Results When Using the Bowl I 2 3 4 Separate the foods into smaller evenly sized pieces maximum 1x1x1 in 3x3x3 cm Process for a shorter or longer period of time Process a smaller amount each time Always have the scraper fitted and use as required The Cutting Tool Cannot Be Removed When Using the Feeder Y Always use the ejector plate 2 Carefully remove the cutting tool by turning it clockwise SPECIFICATIONS Type of Processing l Slices dices shreds and or grates fruit vegetables dry bread cheese nuts and mushrooms 2 Chops and grinds meat fish fruit vegetables and nuts 3 Mixes blends sauces aromatic butter mayonnaise soups dressing thickenings desserts etc D Users l Restaurants dietary kitchens day care centers retirement homes catering establishments e
13. tc 2 Preparing from 10 to 80 portions a day Capacity and Volume les Processes up to 4 lbs per minute with the feeder depending on the type of cutting tool and prod uct 2 Volume of the feeder 1 quart 3 Diameter of the feed tube 2 inches 4 Gross volume of bowl 3 quarts 5 Net volume of bowl with free flowing liquid 1 5 quarts Machine Base L 2 3 4 Un Motor 1000 W 120 V Single phase 60 Hz Thermal motor protection Transmission maintenance free toothed belt Operator Protection Two interlock switches Degree of protection IP34 Power supply socket Grounded single phase 10 A Protective device for circuit must be per National Electrical Code NFPA No 70 current edition Sound level 76 dBA during cutting and 82 dBA during chopping Controls and Speeds l PA Four speeds for perfect processing results in connection with cutting and chopping Automatic speed setting AUTO SPEED that senses whether the feeder or the bowl is fitted During cutting with the feeder the machine operates at 550 rpm in the I position and 850 rpm in the Il position During chopping with the bowl 1 450 rpm in position I and 2 500 rpm in position II The pulse function operates at 850 rpm with the feeder and at 2 500 rpm with the bowl in P position NS Ko ER Cutting Tools and Chopping Knife les The diameter of the cutting tools 1s 7 25 1n 2 The diameter of the chopping knife is 6
14. witch off the machine by setting the variable speed control to the O position Unplug food processor before cleaning If you have used the dicing grid leave it in the machine and force out any remaining cubes with a brush before removing the grid Take all removable parts off of the machine base and remove the sealing ring from the groove on the inside of the lid clean in a hot detergent solution rinse and dry them thoroughly and then replace the sealing ring in the groove All cutting tools can be washed in a hot detergent solution Wipe the machine base with a damp cloth Never use sharp objects scouring powder or pads or high pressure hoses Never leave the knife or cutting tools in a wet condition or on a stainless steel bench when they are not being used but dry them thoroughly and always place them on the wall rack if avail able IROUBLESHOOTING Machine Overheats l SA To eliminate the risk of damage to the motor the unit is fitted with thermal motor protection that automatically switches off the machine if the temperature of the motor should become too high The thermal motor protection has automatic reset which means that the machine can be started again when the motor has cooled down which usually takes between 10 and 30 minutes The Machine Will Not Start or Stops While Running and Can Not Be Re started l Check that the power plug is properly inserted in the wall socket 11 Check the ci
Download Pdf Manuals
Related Search