Belkin F6H550-USB User's Manual
Contents
1. These outlets do not provide battery power during an outage Do not plug surge protectors or power strips into the battery backup outlets i e daisy chaining Equipment such as computer peripherals printers fax machines or desk lamps may be plugged into these outlets The On Off button does not control these outlets 2 Battery Backup Outlets See 2 on Fig 1 Only data sensitive equipment such as a computer monitor and external drive should be plugged into these outlets Battery power is automatically provided in case of a power outage Power AC or battery is not supplied to these outlets when the Unit is switched off Do not plug surge protectors or power strips into the battery backup outlets Caution Never connect a laser printer or scanner to the backup outlets along with other computer equipment To do so might overload the Unit Battery Backup with Surge Protection 3 The On Off button has four functions See 3 on Fig 1 1 Turns on the Unit Depress button at least two seconds The green light illuminates 2 Cold start function If the battery is charged the Unit will work without being plugged into an outlet Depress and hold the key for at least two seconds to turn on the Unit 3 Silence function During On Battery Mode the audible sound can be turned ON or OFF by depressing the switch for less than 1 5 seconds 4 Battery test function During On Line Mode depressing2. Agreement and is effective until terminated The limited license in this Agreement will be automatically terminated if you fail to comply with any of the Terms and conditions in this Agreement You agree that upon such termination you will immediately destroy all programs and documentation including all copies made or obtained by you SOFTWARE PROGRAM DOCUMENTATION AND ANY RELATED INFORMATION GOODS OR SERVICES ARE PROVIDED WITH NO WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER BELKIN HEREBY DISCLAIMS ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE The entire risk of the use results and performance of the software program and documentation is borne by you Should any or all of the product software program documentation or related information goods or services be defective misused unsuitable or cause or give rise to any harm or liability whatsoever you not Belkin or its associates dealers or agents assume the entire liability cost of repair correction or any payment or other remedy whatsoever Furthermore no warranty or guarantee is made regarding the use or results of the product software program documentation or any related information goods or services in terms of correctness accuracy reliability timeliness or otherwise You use and rely on the program at your own risk The following is the only and exclusive
3. PRODUCT YOU ARE AGREEING TO THE TERMS AND CONDITIONS SET OUT IN THIS AGREEMENT IF YOU DO NOT ACCEPT THESE TERMS AND CONDITIONS YOU MUST RETURN THE UNOPENED PRODUCT WITH THE DISKS INSIDE TO THE PARTY FROM WHOM YOU RECEIVED IT SCOPE OF USE In this Agreement software means all machine readable software programs and associated files in this package all modified versions of and upgrades or improvements to such programs and all copies of such programs and files You a single user opening this envelope may use the software on a single central processing unit You may not rent it loan it out or lease it nor use it on a multiuser system LICENSE You have the non exclusive right to use the software You are not permitted to copy modify or transfer the software or documentation You may not compile disassemble or otherwise reverse engineer break down analyze or modify the software USE AND RESTRICTIONS You are permitted to make backup copies of all the software disks for archival purposes only You must reproduce the proprietary notice set forth on the disks and affix them to all backup copies You are not permitted to use these programs in connection with a computer service or to use the backup copies other than as a replacement for the original copy TERM This license is effective upon acceptance by opening this envelope or in any other way using the enclosed software which will constitute your acceptance of and agreement to this
4. replace the new battery pack Fig 3 4 Close the battery cover plate then lock the connector Fig 4 Overview Alarms Backup Slow Alarm When the Unit is in backup mode running on battery the YELLOW LED illuminates and the Unit emits an audible alarm The alarm stops when the Unit returns to normal online operation Low Battery Rapid Alarm In backup mode when the battery energy runs low the Unit beeps rapidly until it either shuts down from a depleted battery or returns to normal online operation Fault 10 Seconds Continuously When the Unit fails it emits an audible alarm continuously for 10 seconds to warn of a fault condition Disconnect the equipment prior to checking it Overview Storage Storage Conditions Store the Unit covered and upright in a cool dry location with its battery fully charged Before storing charge the Unit for at least six 6 hours Extended Storage During extended storage in environments where the ambient temperature is 5 F to 86 F charge the Unit s battery every six 6 months During extended storage in environments where the ambient temperature is 86 F to 113 F charge the Unit s battery every three 3 months Note WserMantalti aaraa Overview Technical Specifications Model F6H375 USB F6H550 USB Input Rated Capacity 550VA 300W Single phase 60Hz Output Step wave Battery Desktop Desktop computer 17 computer monitor 13 min 15 mon
5. the installation options that you have selected If the options are correct then click Install to begin the installation e When the installation program is completed click Done For Other Platforms e This CD provides two installation modes GUI mode and Console mode Enter the directory according the system and run setup bin or setup_console bin to start the installation program Note For UnixWare Irix and Tru64 platform make sure JRE1 3 1 has been install in your system then enter the GenericUnix directory and run setup bin or setup_console bin to start the setup e Read the information provided then click Next e Review the installation options that you have selected If the options are correct then click Install to begin the installation e When the installation program is completed click Done Reboot the system The install program set the Belkin Automatic Power Management Software Running Environment Variables in etc profile reboot the system to make it valid H Uninstall Belkin APM Software Note Before uninstall Belkin APM Software all Belkin APM Software program must be stopped first Otherwise the uninstalling cannot be run completely Windows operating system 1 There are two ways of uninstalling Belkin APM Software a Click directly on the Uninstall Belkin Automatic Power Management Software from the Start menu gt programs gt Belkin Automatic Power Management Software b Use the Add Remo
6. 7372 1 817 244 4415 VISION Battery 604 730 2877 N A Best Battery 888 841 5179 N A Contact Belkin BELKIN www belkin com Belkin B V Boeing Avenue 333 1119 PH Schiphol Rijk The Netherlands 31 0 20 654 7300 31 0 20 654 7349 fax Belkin Tech Support US 800 223 5546 ext 2263 310 898 1100 ext 2263 Europe 00 800 223 55 460 Australia 1800 235 546 New Zealand 0800 235 546 Belkin Ltd 7 Bowen Crescent West Gosford NSW 2250 Australia 61 0 2 4372 8600 61 0 2 4372 8603 fax Belkin Corporation 501 West Walnut Street Compton CA 90220 5221 USA 310 898 1100 310 898 1111 fax i 2005 Belkin Corporation All rights reserved All trade names are registered trademarks of respective manufacturers listed Belkin Ltd Express Business Park Shipton Way Rushden NN10 6GL United Kingdom 44 0 1933 35 2000 44 0 1933 31 2000 fax 614 07417 00
7. BELKIN Introduction Thank you for purchasing the Battery Backup with Surge Protection the Unit Each year frequent natural and man made power disturbances disrupt the power supplied to your home or office electronics These power problems place your hardware software and data at risk Belkin Battery Backups provide an uninterruptible power supply UPS with advanced features as the industry leading solution Package Contents You should have received the following 1 Battery Backup unit 1 Installation CD containing Belkin Automatic Power Management Software the Belkin APM Software for Windows 1 USB Cable 1 Phone Line Cable System Requirements The Battery Backup can be used without the software with any computer using up to a 17 CRT or LCD monitor You do not have to have the software installed to utilize the battery backup outlets To fully utilize the Battery Backup and its software your computer must be running one of the following operating systems Windows XP 2003 2000 ME 98 NT 4 0 SP6 or Linux and have a USB port Overview Features and Functions Before installation please inspect the Unit upon receipt Make sure that nothing is damaged Your Battery Backup features three LED indicators Each is marked by a power icon please familiarize yourself with this chart as it will assist you in the use of your Battery Backup See 4 on Fig 1 Chart 1 On Line o Solid Green The Unit is oper
8. ackup time is very short Battery is not fully charged Recharge the Unit for a minimum of 8 hours Unit is overloaded Remove unnecessary power loads devices UPS fault Contact Belkin Technical Support at techsupp belkin com Safety Information This Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications To assure continued compliance use only shielded interface cables when connecting to computer or peripheral devices Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Belkin Corporation User License Agreement Belkin Corporation Belkin thanks you for choosing one of our products for your use This User License Agreement Agreement contains the terms and conditions under which limited use of the product is licensed to you PLEASE READ THIS NOTICE CAREFULLY DO NOT USE THE SOFTWARE OR PRODUCT UNTIL YOU HAVE READ AND AGREED TO THIS AGREEMENT IF YOU USE THE SOFTWARE AND
9. ating and supplying the utility power to connect loads When the Unit is operating from battery On Battery Flashing Yellow 1 The light blinks every 10 seconds if the Low Battery Unit is operating on battery mode Replace Paltely 2 The light illuminates rapidly every 1 second if the Unit s battery is very nearly depleted When the Unit is operating and supplying the utility power to connect loads the LED flashes and the buzzer emits a sound every 1 minute to indicate the Unit s battery needs to be replaced UPS Fault The LED lights steadily and the buzzer beeps for 10 seconds if a battery fault is found o Solid Yellow o Solid Red The SITE WIRING FAULT LED illuminates when one of the following conditions exist Site Wiring Fault 1 Open or high resistance ground 2 Hot and neutral polarities reversed Overview Important Safety Instructions Please save this User Manual It contains important operating instructions and warranty information pertaining to your Battery Backup Please save or recycle the packaging materials The Unit s packaging was designed with great care to provide protection during shipment and delivery These materials are invaluable if you ever have to return the Unit for service Damage sustained during transit is not covered under the warranty Overview Top Panel Fig 1 BELKIN All 1 Surge Protected Only Outlets See 1 on Fig 1
10. available communication port RS 232 Serial Port or USB port is needed while connecting to UPS with a special connecting cable e For Mac OS X Linux or Unix operating system the user must have the access authority as the super user e TCP IP protocol must be installed to support network management e The user needs to have the access authority as the administrator b Platforms supported by Belkin APM Software The following operating system OS is arranged by the alphabetical order BELKIN e AIX 4 3 3 5 1 5 2 e Compaq Tru 4 Alpha e FreeBSD x86 e HP UX 11 x 11i x e Linux e Mac PPC OSX e SCO UnixWare 7 1 1 7 1 3 SCO Unix 8 0 and SCO OpenServer 5 0 6 5 0 7 SGI Irix 6 5 x e Solaris Sparc 2 6 7 8 9 and Solaris Intel 2 6 7 8 9 e Windows XP 2003 2000 ME 98 NT 4 0 SP6 c Belkin Automatic Power Management Software Installation Steps For Windows platform e Run setup exe in the Windows Disk1 InstData VM directory of your CD to start the installation program e Read the information provided then click Next e Review the installation options that you have selected If the options are correct then click Install to begin the installation e When the installation program is completed click Done For Mac OS X platform e Run setup app in the MacOXS Disk1 InstData directory of your CD to start the installation program e Read the information provided then click Next e Review
11. ax modem line into the surge protected outlets on the side of the Unit The RJ11 modular outlets accept standard single line telephone connections 2 Plug one end of the phone cable into your telephone wall jack and plug the other end into the jack marked IN You may now plug a phone fax or modem into either of the two jacks marked OUT See Fig 3 Fig 3 To Telephone Socket Note This connection is optional but highly recommended as phone fax modem lines often carry dangerous surges and spikes The Unit works properly without a phone fax modem connection Caution The phone fax modem protection feature could be rendered inoperable if improperly installed Make sure that the telephone line from the wall is plugged into the connector marked IN and the devices to be protected phone fax modem are plugged into the connector marked OUT F Connect the USB Universal Serial Port Communication Port See 4 on Fig 2 A USB port is provided to relay the signal to support Windows To fully utilize the Belkin Automatic Power Management Software you will need to connect the Unit to your computer Connect the USB cable to the Unit then connect the other end to your computer s USB port G Install Belkin APM Software a System requirements e 128 MB RAM of memory at least 256MB is recommended e 256 colors and 800 600 resolution or above display is recommended e 160 MB of disk space or above e An
12. itor 10 min 16 hours to 90 Environment 0 40 C Safety UL1778 c UL Regulation EMI FCC Class B IEEE C62 41 category A IEC1000 4 5 Level 2 Appearance Dimensions 134 x 89 x 357mm W H D All specifications are subject to change without prior notice Installation Note Before installation please inspect the Unit Make sure that nothing inside the package is damaged A Connect to AC Utility Power Plug in the AC cord to a wall outlet Please make sure there are no devices plugged into the Unit Check to see whether the SITE WIRING FAULT indicator is lit If it is lit please have the utility wiring inspected by an electrician B Charge the Battery For best results charge the battery for eight hours prior to initial use The Unit charges its battery whenever it is connected to the utility power C Turn on the Unit Turn on your Unit by depressing the On Off button for approximately two seconds You will see the green indicator light come on D Plug in Power Devices Plug your devices into the AC outlets on the Unit To use the Unit as a master on off switch make sure all of the loads are switched on Caution Never connect a laser printer or scanner to the backup outlets along with other computer equipment A laser printer or scanner draws significantly more power when in use than when idle This may overload the Battery Backup E Connect the Phone Fax Modem Lines 1 Connect a single phone f
13. the switch for less than 1 5 seconds causes the Unit to perform a battery test in backup mode Overview Side Panel Fig 2 1 AC Input Power Cord See 1 on Fig 2 Provides power to your Battery Backup 2 Phone Fax Modem Surge Protection See 2 on Fig 2 The phone fax modem lines are surge protected There are one input jack and two output jacks This allows you to split one telephone connection to two separate devices 3 AC Breaker Circuit Breaker see 3 on Fig 2 Should a power overload occur the circuit breaker triggers the Unit to turn off AC power To restore power depress the circuit breaker button to reset then depress the Power button 4 USB Communication Port See 4 on Fig 2 The Unit features a USB communication port Installation of the cable and the Bulldog Plus Software which allows the Unit to connect to your computer is optional The Unit will provide backup power whether or not the cable and software are installed however without them you will be unable to utilize the data management product features Battery Replacement Procedure Replacement requires removing the battery cover plate on the back or bottom of the Battery Backup No tools are needed To replace the battery 1 Push the connector in the arrowhead direction Fig 1 2 Remove the battery cover plate and the battery from the Unit Fig 2 3 Disconnect the insulated connectors from the battery terminals and
14. ve Program under Control and select Change or Remove Programs from the left Select Belkin Automatic Power Management Software and click the Change remove button 2 The Uninstall Program will pop up a prompt and click Uninstall to start the uninstalling To exit the uninstallation click Cancel Mac OS X system open the Terminal from Application gt Utilities gt Terminal enter the installation directory opt upspilot by default and ececute the command sudo Uninatall Enter the system account password when it prompts The installation will be carried out with administrator privilege and can completely uninstall all the files If you just execute the Uninstall command the installation may not has the permission to uninstall all the files Linux and UnixWare system Open the Terminal enter the opt upspilot in the address bar and execute command Uninstall Battery Backup with Surge Protection Troubleshooting PROBLEM POSSIBLE CAUSE SOLUTION Power LED On Off button not pushed Press the On Off button is not lit or pushed less than button more than 2 seconds 2 seconds Unit will not Battery voltage is too low Recharge the Unit power on for at least 8 hours UPS fault Contact Belkin Technical Support at techsupp belkin com Power cord loose AC breaker is tripped Reset the breaker Power disturbances have occurred Unit always on Re plug the power cord battery mode Normal operations B
15. warranty and remedy of any kind Belkin does warrant that the program disks are free from physical defects in materials and workmanship under normal use for a period of one 1 year from the date of purchase as evidenced by a copy of the sales receipt Return the defective disk or documentation with your receipt directly to Belkin for a replacement DISCLAIMER Belkin or its associates will in no event be liable i in any amount for lost profits or special incidental punitive or consequential damages or ii for any claim or damage of any nature or under any theory whatsoever in any amount in excess of the purchase price you paid for the product The warranties and remedies here set forth are exclusive and in lieu of all others oral or written expressed or implied Some jurisdictions do not allow exclusion or limitation of implied warranties or of liability for incidental damages so the foregoing limitations or exclusion may not apply to you This warranty gives you specific legal rights which vary from jurisdiction to jurisdiction WserMantalta aerae HOWEVER YOU WAIVE SUCH RIGHTS EXCEPT AS EXPRESSLY PROVIDED UNDER THE TERMS AND CONDITIONS HAVE THIS AGREEMENT TO THE MAXIMUM EXTENT ALLOWED BY LAW The license is governed by the laws prevailing in the State of New York without regard to its conflicts of laws principles ACKNOWLEDGMENT By opening the package on which this Agreement is printed or through which it is visible
16. you acknowledge that you have read this Agreement understand it and agree that this Agreement is the complete and exclusive statement of agreement between yourself and Belkin and supersedes any prior agreements oral or written and any other communications relating to the subject matter of this Agreement SEVERABILITY Any term or provision of this Agreement or any application thereof which may be prohibited or unenforceable by law in a particular jurisdiction shall be interpreted and enforced to the maximum extent allowed in such jurisdiction which the parties acknowledge could mean severing the provision from this Agreement or if allowed enforcing it in a narrower form without affecting the remainder of this Agreement or any other application of such term or provision in such jurisdiction or application of such term or provision in any other jurisdiction Safety Information Caution I Internal battery voltage is 12V DC The Unit is intended for installation in a controlled environment temperature controlled indoor area free of conductive contaminants All batteries used are sealed lead batteries Batteries must be recycled Recycling Your Unit contains a non spillable sealed lead battery On the battery you will find the battery name Please reference the chart below for recycling information Battery Name Recycling Inside the USA Outside the USA Recycling BB Battery 800 278 8599 N A CSB Battery 800 738
Download Pdf Manuals
Related Search