Behringer Eurolight LD6230 Installation Instructions
Contents
1. CEE connector pin allocation Removable mains connector cables with mains interconnections pursuant IEC60320 must match the minimal load carrying capacity of the connector or must comply with the IEC60799 standard The interconnection and the cable must comply with prevalent nominal values maximal voltage and current During the installation please adhere to the instructions provided by the connector manufacturer Specifications Number 6 0 2 A min 10 A max Load per channel Maximal load per channel 10 A using a 3 phase connector 50 60 Hz Frequency Power supply 3 phase connector internal terminal block PG cable screw joint CEE connector optional installation by qualified personnel 0 to 10 V via 8 pin DIN DMX512 via XLR 5 pin Analog Digital Digital Load DMX512 via XLR 5 pin Internal terminal block PG cable screw joint HARTING optional installation by qualified personnel System Fuses Load securing per channel 10 A cable protection switch type C 2x T100 mA H 250V 1x T 160 mA H 250 V for voltage range 220 230 V EU 2 xT 160 mA H 250V 1x T315 mA H 250 V for voltage range 120 V UL Control section fuse Voltage USA Canada 120 V 60 Hz Europe U K Australia 240 V 50 Hz Maximum power consumption 3x20A Dimensions Weight Dimensions H x W x D approx 3 43x 19 x 15 0 approx 84 3 x 482 6 x 403 8 mm approx2. CH 1 FUSE CH 4 CH 2 FUSE CH 5 DIGITAL ANALOG l DIMMER PACK 6 CHANNELS x10 A b CH 3 FUSE CH 6 Oo amp A behringer WAT AAAS Installation Instructions EUROLIGHT LD6230 Professional 6 Channel 10 A Dimmer Pack with DMX and Analog Control EX behringer com behringer ED Ee 2 EUROLIGHT LD6230 Installation Instructions Important Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE D ELECTROCUTION NE PAS OUVRIR Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock Use only high quality professional speaker cables with 14 TS or twist locking plugs pre installed All other installation or modification should be performed only by qualified personnel This symbol wherever it appears alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock This symbol wherever it appears alerts you to important operating and maintenance instructions in the accompanying literature Please read the manual Caution To reduce the risk of electric shock do not remove the top cover or the rear section No user serviceable parts inside Refer servicing to qualified personnel Caution To reduce the risk of fire or electric shock do not expo
3. 21 6 Ibs 9 80 kg Weight BEHRINGER continuously strives to assure the highest quality standards possible Required modifications may be implemented without prior notice Technical data and the appearance of the unit may deviate from the above values and or illustrations behringer com 6 EUROLIGHT LD6230 Installation Instructions EN FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION BEHRINGER EUROLIGHT LD6230 C Responsible Party Name MUSIC Group Services US Inc Address 18912 North Creek Parkway Suite 200 Bothell WA 98011 USA Phone Fax No Phone 1 425 672 0816 Fax 1 425 673 7647 EUROLIGHT LD6230 complies with the FCC rules as mentioned in the following paragraph This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the
4. not the country for which the product was originally developed and manufactured this modification adaptation shall not be considered a defect in materials or workmanship This limited warranty does not cover any such modification adaptation regardless of whether it was carried out properly or not Under the terms of this limited warranty MUSIC Group shall not be held responsible for any cost resulting from such a modification adaptation This limited warranty covers only the product hardware It does not cover technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the product Any such software is provided AS IS unless expressly provided for in any enclosed software limited warranty This limited warranty is invalid if the factory applied serial number has been altered or removed from the product Free inspections and maintenance repair work are expressly excluded from this limited warranty in particular if caused by improper handling of the product by the user This also applies to defects caused by normal wear and tear in particular of faders crossfaders potentiometers keys buttons guitar strings illuminants and similar parts 6 Damage defects caused by the following conditions are not covered by this limited warranty e improper handling neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or se
5. representation This manual is copyrighted No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying and recording of any kind for any purpose without the express written permission of MUSIC Group IP Ltd ALL RIGHTS RESERVED 2012 MUSIC Group IP Ltd Trident Chambers Wickhams Cay P O Box 146 Road Town Tortola British Virgin Islands behringer com
6. 17 5007 To assure compliance with Directive 89 336 EEC only use specified upstream line filters with your EUROLIGHT Using it without line filters specified by BEHRINGER may lead to electromagnetic interference More detailed information on this subject can be found at behringer com Safety and Initial Operation As soon as you connect your LD6230 to the mains internal controls are activated The six automated fuses circuit breakers can all handle 10 A and serve as overload protection for the connected equipment Please keep in mind that activating circuit breakers 1 2 3 4 5 or 6 also means that the respective channels can conduct voltage Electronic controls are additionally protected with triple high sensitivity fuses located on the main board Defective fuses must be replaced with fuses with identical rating The LD6230 is a Class device in which a low Ohm protective ground wire is an integral part of its safety design During the installation make sure that a low Ohm protective conductor lt 0 1 Ohm exists between all bare metal parts and the grounding on the main connector Ce u X X L2 X X L3 X X Activation of control electronics and respective output channel Connector Terminal Strip The connector terminal strip of your LD6230 is laid out for cables with diameters between 0 326 mm AWG 22 and 4 mm AWG 12 When using flexible access lines cable end contacts corresponding t
7. 4 MUSIC Group shall at its discretion either replace or repair the product using suitable new or reconditioned product or parts In case MUSIC Group decides to replace the entire product this limited warranty shall apply to the replacement product for the remaining initial warranty period i e one 1 year or otherwise applicable minimum warranty period from the date of purchase of the original product Upon validation of the warranty claim the repaired or replacement product will be returned to the user freight prepaid by MUSIC Group Warranty claims other than those indicated above are expressly excluded PLEASE RETAIN YOUR SALES RECEIPT IT IS YOUR PROOF OF PURCHASE COVERING YOUR LIMITED WARRANTY THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF OF PURCHASE 2 Online registration Please do remember to register your new BEHRINGER equipment right after your purchase at behringer com under Support and kindly read the terms and conditions of our limited warranty carefully Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently Thank you for your cooperation 3 Return materials authorization To obtain warranty service please contact the retailer from whom the equipment was purchased Should your MUSIC Group Authorized Reseller not be located in your vicinity you may contact the MUSIC Group Authorized Fulfiller for your country listed under behri
8. GROUP PRODUCTS ARE SOLD THROUGH AUTHORIZED FULLFILLERS AND RESELLERS ONLY FULLFILLERS AND RESELLERS ARE NOT AGENTS OF MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIED UNDERTAKING OR REPRESENTATION THIS MANUAL IS COPYRIGHTED NO PART OF THIS MANUAL MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS ELECTRONIC OR MECHANICAL INCLUDING PHOTOCOPYING AND RECORDING OF ANY KIND FOR ANY PURPOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF MUSIC GROUP IP LTD ALL RIGHTS RESERVED 2012 MUSIC Group IP Ltd Trident Chambers Wickhams Cay P 0 Box 146 Road Town Tortola British Virgin Islands LIMITED WARRANTY 1 Warranty This limited warranty is valid only if you purchased the product from a MUSIC Group Authorized Reseller in the country of purchase A list of authorized resellers can be found on BEHRINGER website behringer com under Where to Buy or you can contact the MUSIC Group office closest to you MUSIC Group warrants the mechanical and electronic components of this product to be free of defects in material and workmanship if used under normal operating conditions for a period of one 1 year from the original date of purchase see the Limited Warranty terms in 4 below unless a longer minimum warranty period is mandated by applicable local laws If the product shows any defects within the specified warranty period and that defect is not excluded under
9. ansferability This limited warranty is extended exclusively to the original buyer customer of authorized reseller and is not transferable to anyone who may subsequently purchase this product No other person reseller etc shall be entitled to give any warranty promise on behalf of MUSIC Group 6 Claim for damage Subject only to the operation of mandatory applicable local laws MUSIC Group shall have no liability to the buyer under this warranty for any consequential or indirect loss or damage of any kind In no event shall the liability of MUSIC Group under this limited warranty exceed the invoiced value of the product 7 Limitation of liability This limited warranty is the complete and exclusive warranty between you and MUSIC Group It supersedes all other written or oral communications related to this product MUSIC Group provides no other warranties for this product 8 Other warranty rights and national law This limited warranty does not exclude or limit the buyer s statutory rights as a consumer in any way The limited warranty regulations mentioned herein are applicable unless they constitute an infringement of applicable mandatory local laws This warranty does not detract from the seller s obligations in regard to any lack of conformity of the product and any hidden defect 9 Amendment Warranty service conditions are subject to change without notice For the latest warranty terms and conditions an
10. d additional information regarding MUSIC Group s limited warranty please see complete details online at behringer com MUSIC Group Macao Commercial Offshore Limited of Rue de Pequim No 202 A Macau Finance Centre 9 J Macau including all MUSIC Group companies behringer com 4 EUROLIGHT LD6230 Installation Instructions The BEHRINGER EUROLIGHT LD6230 Dimmer Pack was developed to meet the highest demands of light engineering Its wide ranging functions make it an all purpose workhorse for various commercial applications TV studios theatre or live events The EUROLIGHT LD6230 has all the important features needed to control your lighting equipment yet its controls are clearly arranged and simple to use You can select between digital DMX or analog control You get trouble free operation with the extensive LEDs used for signal error detection Important Information Installation as well as initial operation must be performed by qualified personnel Always assure that your LD6230 is completely disconnected from the mains before removing the casing cover The LD6230 was designed for indoor use only Please keep in mind that sudden temperature changes e g bringing your equipment from colder environments into warmer environments may cause condensation on electronic components leading to possible equipment damage and physical harm to the operator Please adhere to all applicable national safety standards during installat
11. interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Important information Changes or modifications to the equipment not expressly approved by MUSIC Group can void the user s authority to use the equipment Technical specifications and appearances are subject to change without notice and accuracy is not guaranteed BEHRINGER is part of the MUSIC Group music group com All trademarks are the property of their respective owners MUSIC Group accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description photograph or statement contained herein Colors and specifications may VARY FROM ACTUAL PRODUCT MUSIC Group products are sold through authorized FULLFILLERS AND RESELLERS only FULLFILLERS AND RESELLERS are not agents of MUSIC Group and have absolutely no authority to bind MUSIC Group by any express or implied undertaking or
12. ion Please read the installation instructions and the enclosed user s manual in their entirety to familiarize yourself with the LD6230 and all of its functions Please follow all instructions and store both the installation instructions and the manual in a safe place for future reference Please assure that your EUROLIGHT is sufficiently cooled and that it is not placed near heat sources that could cause overheating Ifyou want to run your EUROLIGHT on mains voltage other than factory specified voltage contact the nearest BEHRINGER service center To effectively limit harmonic currents and avoid voltage fluctuations that could affect other electrical appliances connect this equipment to an AC outlet that complies with all applicable technical standards In all other cases contact your local power supply provider for advice prior to usage Mains IIluminant Connectors To facilitate additional flexibility your dimmer pack has a connector terminal strip Cable bushings for connecting to the mains and your illuminants are located in the back Flexibility is further enhanced with the option to retrofit a CEE connector and a 16 pin HARTING connector Both fixed and mobile installations require compliance with IEC 61010 1 2001 EN 6110 1 2001 In particular a 3 phase separator pursuant IEC60947 1 and 1EC60947 3 needs to be included in the installation This separator needs to be labeled according to IEC 60417 50008 and IEC 04
13. nger com 3 EUROLIGHT LD6230 Installation Instructions Support at behringer com If your country is not listed please check if your problem can be dealt with by our Online Support which may also be found under Support at behringer com Alternatively please submit an online warranty claim at behringer com BEFORE returning the product All inquiries must be accompanied by a description of the problem and the serial number of the product After verifying the product s warranty eligibility with the original sales receipt MUSIC Group will then issue a Return Materials Authorization RMA number Subsequently the product must be returned in its original shipping carton together with the return authorization number to the address indicated by MUSIC Group Shipments without freight prepaid will not be accepted 4 Warranty Exclusions This limited warranty does not cover consumable parts including but not limited to fuses and batteries Where applicable MUSIC Group warrants the valves or meters contained in the product to be free from defects in material and workmanship for a period of ninety 90 days from date of purchase This limited warranty does not cover the product if it has been electronically or mechanically modified in any way If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level in any country which is
14. nts accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid A a injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection 16 Where the MAINS plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable LEGAL DISCLAIMER TECHNICAL SPECIFICATIONS AND APPEARANCES ARE SUBJECT TO CHANGE WITHOUT NOTICE AND ACCURACY IS NOT GUARANTEED BEHRINGER IS PART OF THE MUSIC GROUP MUSIC GROUP COM ALL TRADEMARKS ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS MUSIC GROUP ACCEPTS NO LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED BY ANY PERSON WHO RELIES EITHER WHOLLY OR IN PART UPON ANY DESCRIPTION PHOTOGRAPH OR STATEMENT CONTAINED HEREIN COLORS AND SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT MUSIC
15. o manufacturer specifications have to be used To assure good contact skin the cable endings between 9 13 mm During the installation all applicable national standards need to be adhered to a Illustration LD6230 connector terminal strip When your LD6230 leaves the assembly plant all incoming and outgoing neutral conductor connectors 3 are bridged The incoming phases L1 L1 L2 L2 and L3 L3 are always connected to one another in pairs and switched to the overload protection of the channels 1 to 6 They protect output connectors E1 to E6 Each of the channels can handle currents of maximum 10 Amperes The green yellow conductors 2 PE may only be used as protective conductors The lowest cable gauge between L1 and L3 incoming neutral conductor N and protective earth PE is 4 mm AWG 12 For outgoing channels E1 to E6 use cables with gauges corresponding to the loads used 2 5 mm AWG 14 or 1 5 mm AWG 16 Output assessment A Nominal cross section mm EU awws O 6 10 1 5 16 13 16 2 5 14 18 25 4 12 During the installation please adhere to all manufacturer instructions Regardless from mains supply voltage the maximum output current of the EUROLIGHT LD6230 is 10 A per dimmer circle behringer com 5 EUROLIGHT LD6230 Installation Instructions Please make sure that each dimmer load is connected to a separate channel Never connect more than one output to just
16. one common neutral conductor ATTENTION Due to electrocution danger do not use your dimmer pack if there are bare cables visible Connection Options for Flexible Usage Output Connector HARTING In the back of your LD6230 there is a cable bushing for connecting your illuminants Open the flap on the top of the LD6230 to get to the terminal clamps used for this purpose Here you have the option to retrofit a 16 pin HARTING connector To do that you first have to remove the back bearing cover sheet and connect the HARTING connector to the terminal clamps PIN assignment HARTING connector PIN1 Phase channel 1 E1 PINS Neutral channel 1 N PIN2 Phase channel 2 E2 PIN10 Neutral channel 2 N PIN3 Phase channel 3 E3 PIN 11 Neutral channel 3 N PIN4 Phase channel 4 E4 PIN12 Neutral channel 4 N PINS Phase channel 5 E5 PIN13 Neutral channel 5 N PIN6 Phase channel 6 E6 PIN14 Neutral channel 6 N PIN7 free PIN1IS free PINS free PIN16 free Ground wires need to be fastened to their respective PE connectors CEE Power Supply Connector Also located in the back is a cable bushing for the mains supply Here you can retrofit a 5 pin CEE 32 A mains connector by removing the back bearing cover sheet and connect the CEE high voltage connector to the connecting terminal The following illustration shows how the connections are allocated A
17. rvice manuals e connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used e damage defects caused by acts of God Nature accident fire flood etc or any other condition that is beyond the control of MUSIC Group Any repair or opening of the unit carried out by unauthorized personnel user included will void the limited warranty If an inspection of the product by MUSIC Group shows that the defect in question is not covered by the limited warranty the inspection costs are payable by the customer 2 Products which do not meet the terms of this limited warranty will be repaired exclusively at the buyer s expense MUSIC Group or its authorized service center will inform the buyer of any such circumstance If the buyer fails to submit a written repair order within 6 weeks after notification MUSIC Group will return the unit C 0 D with a separate invoice for freight and packing Such costs will also be invoiced separately when the buyer has sent in a written repair order MUSIC Group Authorized Resellers do not sell new products directly in online auctions Purchases made through an online auction are on a buyer beware basis Online auction confirmations or sales receipts are not accepted for warranty verification and MUSIC Group will not repair or replace any product purchased through an online auction 5 Warranty tr
18. se this appliance to rain and moisture The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids such as vases shall be placed on the apparatus Caution These service instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions Repairs have to be performed by qualified service personnel Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth NOY WHN Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Donotinstall near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Use only attachme
Download Pdf Manuals
Related Search