Home

Avaya Bay Command Console BCC User's Manual

1. Table A 1 System Commands continued Login Access Privileges Command Purpose Manager User mset lt obj_name gt lt obj_id gt lt attr_name gt Modify set the values of data objects in f lt attr_id gt lt inst_id gt lt value gt the device MIB BCC only partition create delete lt vol gt Create or delete a partition on existing v v file system media password Manager Change the password of the Manager v account password User Change the password of the User VY VY account ping lt protocol gt lt address gt Initiate an ECHO request reply VY VY t lt timeout gt handshake pktdump lt line number gt s lt start gt Display packets that have been captured c lt count gt by an interface configured for Packet Capture prom v w Update or verify the software located on f lt vol gt lt ROM_Update_File gt lt slot_ID gt a flash PROM device lt slot_ID gt pwc Display the path to your current working W v BCC configuration mode only location in the tree starting from root readexe lt vol gt lt filename gt Validate the checksums of an executable v image and print out all the file header information record open close fileonly pause Record to a file all messages written to W lt vol gt lt filename gt the terminal You can open pause and close a recording session Technician Interface only reset lt s ot_ D gt Reboot the GAME image on the VY spe
2. p arp 1 2 3 4 1 ethernet 2 2 protocol interface serial 3 1 P interface BCC0012C Figure 1 2 Sample BCC Configuration 1 4 303562 A Rev 00 Overview of the BCC Context You use BCC commands to create new objects and to modify or delete objects in an existing configuration hierarchy You begin at root level in BCC configuration mode and navigate to objects in the device configuration tree For example on a BLN router you can use BCC commands to add a new physical interface such as Ethernet on box add IP to the Ethernet interface and then add RIP to IP on that interface Figure 1 3 shows the sequence of commands necessary to build this configuration box ethernet 2 1 Ethernet Slot 2 Connection 1 ethernet 2 1 ip address 1 2 3 4 mask 255 0 0 0 IP Address 1 2 3 4 Mask 255 0 0 0 ip 1 2 3 4 255 0 0 0 rip rip 1 2 3 4 rip 1 2 3 4 BCCO017A Figure 1 3 Configuring IP and RIP on an Ethernet Interface Your working location within the BCC configuration tree is referred to as the context Just as a UNIX file system has a current working directory within which you can add modify or delete files the BCC configuration tree has a current working context within which you can add modify disable reenable or delete objects 303562 A Rev 00 1 5 Using the Bay Command Console BCC The BCC understands the contex
3. Entering Configuration Commands from a File When you are logged in to the BCC as Manager you can use the source command in configuration mode to read BCC configuration and navigation commands from a designated ASCII source file into the active device configuration Caution The source command makes immediate changes to the active device configuration The source command merges new configuration data from a file with existing data in device memory If the file you specify contains configuration commands pertaining to objects already defined on the device those commands overwrite the current configuration Note If the BCC detects an error in the source file it stops reading commands into the device configuration Syntax for the source command is as follows source lt volume gt lt filename gt Saving the Active Configuration as a Bootable Binary File When you finish using BCC commands to modify an existing configuration save the new configuration to a file on an NVFS flash volume At boot time the router loses any configuration changes not previously saved to an NVFS volume The following command saves config as a bootable binary file on a volume you specify bec gt save config lt volume gt lt filename gt 3 12 303562 A Rev 00 Chapter 4 Tutorial Configuring a Network Device This chapter provides a tutorial that guides you through the initial configuration of a Bay Networks device using
4. User Login Errors Manager Login Errors Other Login Errors TTY Frame Errors TTY Overrun Errors TTY Parity Errors TTY FIFO Errors Port number for the information displayed Corresponding port name Port s current state Absent Disabled Down Init or Up Number of logins failed and successful on the console port Number of failed login attempts that the User login account has made on the console port Number of failed login attempts that the Manager login account has made on the console port Number of failed login attempts made by login accounts other than User and Manager on the console port Number of frame errors on the console port Number of overrun errors on the console port Number of parity errors on the console port Number of FIFO errors on the console port A high number of errors over a short period of time may indicate a problem with the line C 4 303562 A Rev 00 System show Commands show hardware The show hardware lt option gt commands display information about router hardware The show hardware command supports the following subcommand options backplane memory lt slot gt config_file proms image slots backplane Displays information about the state of the backplane hardware The table includes the backplane type revision and serial number The revision and serial numbers are in decimal format config_file Displays the configuration file u
5. lt module gt numbering corresponds to net module numbering 1 through 4 on each ASN lt connector gt numbering starts at 1 on each net module per media type Example ethernet slot 2 module 3 connector 2 This is an Ethernet interface on connector 2 of net module 3 in ASN 2 of a stacked ASN configuration continued 303562 A Rev 00 D 1 Using the Bay Command Console BCC Table D 1 Syntax for Specifying Module Location per Device continued Platform Syntax ARN lt interface gt lt slot gt lt connector gt lt interface gt Interface type ethernet token ring serial etc e lt slot gt 1 lt connector gt numbering depends on the port type LAN or WAN LAN connector numbering starts at 1 on the base module which contains only LAN ports LAN connector numbering continues in ascending order starting with the first LAN port on an ARN expansion module The ARN expansion module plugs into the ARN base module WAN connector numbering starts with connector 1 on WAN adapter module 1 continues with connector 2 on WAN adapter module 2 and ascends sequentially with WAN connectors 3 through n on the ARN expansion module Example ethernet slot 1 connector 2 This interface is configured on LAN connector 2 which exists physically on an Ethernet expansion module Ethernet connector 1 is on the base module Example serial slot 1 connector 3 This is a serial WAN interface c
6. 3 6 A acronyms Xvi B backplane hardware C 5 BCC accessing 2 1 command files 3 10 commands entering 3 1 show C 1 system A 1 configuration cycle 4 4 defined 1 1 Help 2 11 A 4 platform requirements 1 2 terminology and concepts 1 6 board defined 1 8 bootstrap PROM revision date C 6 box wide objects 1 7 buffers system C 10 C class defined 1 6 commands 2 11 back 2 3 config 1 2 configuration 3 5 303562 A Rev 00 Index continuing 3 4 editing 3 3 entering 3 1 Help 2 11 Iso 2 10 pwe 2 3 show config 2 8 2 10 show console C 2 show hardware C 5 show process C 7 show system C 10 source 3 12 system A 1 connector defined 1 9 console subcommands C 2 context changing 2 3 defined 1 5 displaying 2 3 continuing a command line 3 4 conventions text xiv creating a new configuration 4 1 D delete command 3 10 4 17 derived parameters defined 1 10 diagnostics PROM revision date C 6 disable command 3 10 4 15 E editing commands 3 3 educational services xvii enable command 3 10 4 16 Index 1 entering the BCC 2 1 exiting the BCC 2 1 G global objects defined 1 7 H hardware information C 5 Help commands 2 11 A 4 history buffer 3 2 image software C 5 instance identifier 1 7 2 6 interface defined 1 9 L line defined 1 9 location in configuration hierarchy 2 3 login privileges and procedures
7. Using the Bay Command Console BCC BayRS Version 13 00 Site Manager Software Version 7 00 BCC Version 4 05 Part No 303562 A Rev 00 October 1998 GIS Bay Networks Where Information Flows GIS Bay Networks Where Information Flows 4401 Great America Parkway 8 Federal Street Santa Clara CA 95054 Billerica MA 01821 Copyright 1998 Bay Networks Inc All rights reserved Printed in the USA October 1998 The information in this document is subject to change without notice The statements configurations technical data and recommendations in this document are believed to be accurate and reliable but are presented without express or implied warranty Users must take full responsibility for their applications of any products specified in this document The information in this document is proprietary to Bay Networks Inc The software described in this document is furnished under a license agreement and may only be used in accordance with the terms of that license A summary of the Software License is included in this document Trademarks ACE AN BCN BLN BN FRE Optivity PPX Quick2Config and Bay Networks are registered trademarks and Advanced Remote Node ANH ARN ASN BayRS BaySecure BayStack BCC SPEX System 5000 and the Bay Networks logo are trademarks of Bay Networks Inc Microsoft MS MS DOS Win32 Windows and Windows NT are registered trademarks of Microsoft Corporation All other trademarks and
8. Configuration commands make real time changes to the device configuration Command Syntax Requirements BCC syntax consists of object names parameter names and values and various types of punctuation e All object and parameter names appear as one word hyphenated where necessary in the BCC command line e Parameters have either a single value or multiple values enclosed in braces x y z in the command line You can accept the default value or supply a value for each parameter associated with a configurable object e Parameters and their values must appear as a pair in the same command line 303562 A Rev 00 3 5 Using the Bay Command Console BCC e Syntax for specifying the object you want to configure may vary according to the number of slots in the Bay Networks device to which you are connected Appendix D lists the syntax for specifying the physical location of a module for each Bay Networks device that the BCC supports e If you enter the name of an object without values for its required parameters or with values inappropriate for its required parameters the BCC returns usage Help as shown in the following example box ethernet Required parameter slot was not specified for ethernet Usage ethernet slot lt value gt connector lt value gt Or ethernet lt slot gt lt connector gt Using Basic Full Syntax The basic or full syntax for BCC commands consists of the following required and optional e
9. processor module and the network module type revision and serial number C 6 303562 A Rev 00 System show Commands show process The show process lt option gt commands display information about the use of resources buffers CPU memory lists and so on on the router The show process command supports the following subcommand options buffers detail total list detail total cpu detail total memory detail total buffers detail total Displays the number and percentage of buffers used by all processes on the router The table includes the following information Name Name of the process if you specify the detail option Slot Slot number Used Number of buffers used Used Percentage of buffers used Max Maximum buffers if you specify the total option Free Free buffers if you specify the total option 303562 A Rev 00 C 7 Using the Bay Command Console BCC cpu detail total Displays the CPU usage in hundredths of seconds and the percentage of total CPU time used by all processes on the router detail Displays details about CPU usage for all processes total Displays only CPU statistics totals Note For information about how to obtain a list of available processes see the show process list command The table includes the following information Name The name of the process Slot Slot number Used Hundredths of seconds used by each proc
10. 0 23 Enable the Telnet server entity on the router manager public 0 0 0 0 telnet telnet server server 24 Add TFTP services globally to the router server tftp tftp The BCC automatically searches back toward root to find the parent context suitable for Telnet and TFTP in this case box The BCC then adds Telnet and TFTP to the device configuration Note the new tftpt prompt 4 12 303562 A Rev 00 Tutorial Configuring a Network Device 25 Check the values currently assigned to parameters of TFTP tftp info on box state enabled default volume 2 retry timeout 5 close timeout 25 retry count 5 26 Change the default volume number for TFTP to 5 tftpf def 5 tftpt 27 Verify the change to the default volume number tftp def default volume 5 28 Add FTP globally to the router tftpt ftp ftp The BCC automatically searches back toward root to find the parent context suitable for FTP in this case box The BCC then adds FTP to the device configuration Note the new tp prompt 29 Check the definitions for parameters of FTP ftp help ftp ftp Parameters Identifies the parent s of this object state Indicates the administrative state of this object enabled or disabled default volume Specifies the default volume where transferred files are written retrieved 303562 A Rev 00 4 13 Using the Bay Command Console BCC 30 Check values currently assigned t
11. 2 1 Iso command 2 10 Manager User privilege levels 2 2 memory hardware C 6 system C 11 navigating using configuration commands 2 4 using the back command 2 3 0 objects defined 1 6 deleting 4 17 Index 2 disabling 4 15 enabling 4 16 online Help BCC 2 11 optional parameters defined 1 10 P parameters defined 1 10 Help 2 11 specifying values for 3 8 path specifying 2 6 2 7 port defined 1 9 product support xvii PROM information hardware C 6 protocols show system command C 11 publications Bay Networks xvi pwc command 2 3 R reading commands from a file 3 12 recalling commands 3 2 required parameters defined 1 10 S saving configuration commands 3 11 serial port configuration C 2 error statistics C 4 show commands config 2 8 console C 2 hardware C 5 process C 7 system C 10 show config command 2 8 slot defined 1 8 slots hardware C 6 source command 3 12 specifying a path 2 6 2 7 303562 A Rev 00 statistics console C 4 support Bay Networks xvii syntax configuration commands 3 5 D 1 Help 2 11 system information C 11 T TCL support B 1 technical publications xvi technical support xvii Technician Interface 2 1 text conventions xiv U User privileges 2 2 303562 A Rev 00 Index 3
12. Bay Networks router 1 Open a Technician Interface session with the target router For detailed information about opening a Technician Interface session see Using Technician Interface Software 2 Enter the Manager or User command at the Login prompt that appears on your Telnet or console display The Manager login allows you to enter any system command and allows read write access to the device configuration The User login allows you to enter only user level system command and allows read only access to the device configuration 303562 A Rev 00 2 1 Using the Bay Command Console BCC Enter bcc at the Technician Interface prompt Routerl gt bee Welcome to Bay Command Console To enter configuration mode type config To list all system commands type To exit the BCC type exit bec gt Start BCC configuration mode by entering config at the cc gt prompt bec gt config box You enter configuration mode at the root box level of the BCC configuration tree The prompt ends with a pound symbol if you have read write privileges Manager only or with a greater than symbol gt if you have read only privileges Manager or User If you enter BCC configuration mode as Manager and want to change your privilege level for the current session from read write to read only enter config read only To change Manager privileges back to read write enter config read write You cannot change your privilege
13. Isearch uplevel Isort upvar open e while proc puts rename return set source split subst For more information about definitions syntax and applications for these TCL commands refer to the following book Ousterhout J Tcl and the Tk Toolkit Reading Mass Addison Wesley ISBN 0 201 63337 X 303562 A Rev 00 B 1 Appendix C System show Commands This appendix describes the following BCC system show commands Topic Page show console C2 show hardware C 5 show process C 7 show system C 10 For information about the show config command see Displaying Configuration Data on page 2 8 303562 A Rev 00 C 1 Using the Bay Command Console BCC show console The show console lt option gt commands display console port configuration and statistics information The show console command supports the following options config stats config Displays configuration and Technician Interface environment information for the serial ports configured on your system or for a specific port The table includes the following information Port Number Port number for the information displayed Valid ports are 1 2 3 and 4 Not all systems have four physical ports A configured port that does not exist is in the Absent state State Port s current state as follows Absent Not physically present Disabled Unavailable Down Unavaila
14. The BCC treats these two characters and any trailing spaces as if they were exactly one space Until you press Return without a preceding backslash character the BCC replaces the pound symbol in the context sensitive prompt with an underscore _ character Example ip 1 2 3 4 255 0 0 0 cost 2 ip 1 2 3 4 255 0 0 0_ mask reply on ip 1 2 3 4 255 0 0 0_ proxy on ip 1 2 3 4 255 0 0 0_ aging cache on ip 1 2 3 4 255 0 0 0 Some command symbols normally used in pairs to denote the beginning and the end of a set of data also produce the continuation underscore prompt including braces I brackets and quotation marks Example box box box 3 4 303562 A Rev 00 Entering Commands and Using Command Files Note If you inadvertently type one of the opening symbols and see an underscore prompt just type the corresponding closing symbol to restore the normal prompt in BCC configuration mode System Commands The BCC supports all system commands described in Appendix A For Help ona specific command enter help lt command gt for example help save at any BCC prompt Configuration Command Syntax This section describes BCC configuration commands and the syntax requirements for those commands This section also describes how to enter BCC configuration commands using the following formats e Basic full syntax e Default syntax e Abbreviated syntax Caution
15. clause of FAR 52 227 19 and the limitations set out in this license for civilian agencies and subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause of DFARS 252 227 7013 for agencies of the Department of Defense or their successors whichever is applicable 6 Use of Software in the European Community This provision applies to all Software acquired for use within the European Community If Licensee uses the Software within a country in the European Community the Software Directive enacted by the Council of European Communities Directive dated 14 May 1991 will apply to the examination of the Software to facilitate interoperability Licensee agrees to notify Bay Networks of any such intended examination of the Software and may procure support and assistance from Bay Networks 7 Term and termination This license is effective until terminated however all of the restrictions with respect to Bay Networks copyright in the Software and user manuals will cease being effective at the date of expiration of the Bay Networks copyright those restrictions relating to use and disclosure of Bay Networks confidential information shall continue in effect Licensee may terminate this license at any time The license will automatically terminate if Licensee fails to comply with any of the terms and conditions of the license Upon termination for any reason Licensee will immediately destroy or return to Bay Networks the Software u
16. clear clearlog commit compact config context cp cwc date debug ethernet 13 1 delete diags dinfo dir disable enable exit format help history loadmap log logout lso mget circuit name connector hardware filter has name mkdir mlist more mount mset partition password ping pktdump pop prom pwc readexe reconfig record on receive queue length slot state transmit queue length reset restart rm rmdir save securelogin show source stamp stop system tic unmount xmodem Based on the Sub Contexts list you can add ip interface IP or ipx interface IPX to this Ethernet port The list of configurable objects depends on the board type described in the current prompt For example 100BASE T modules additionally allow you to configure an autoneg autonegotiation object at this level You can also modify the values currently assigned to Parameters in Current Context parameters of ethernet 13 1 shown above The System Commands list always appears along with information about configurable objects and parameters 303562 A Rev 00 4 7 Using the Bay Command Console BCC 7 Add IP address 192 168 133 114 to ethernet 13 1 ethernet 13 1 ip 192 168 133 114 Usage ip address lt value gt mask lt value gt Or ip lt address gt lt mask gt Required parameter mask was not specified for ip The error message appears because the BCC requir
17. find the configuration or navigation path to a specific object 303562 A Rev 00 2 13 Using the Bay Command Console BCC Listing Available Objects Parameters and System Commands To list the names of all objects parameters and system commands you can enter from the current context enter the command Example ip 192 168 125 34 255 255 255 224 Sub Contexts arp igmp ospf rdise rip Parameters in Current Context address address resolution all subnet broadcast assocaddr broadcast cache size configured mac address System Commands back beccSource bconfig boot cd clear clearlog commit compact config cp cwc date debug delete diags dinfo dir disable cost end station support has host cache aging mask mask reply mtu discovery display enable exit format getcfg help help file version history ifconfig info loadmap log logout lso mget mlist more mset partition password on proxy redirects state udp checksum ping pktdump pop prom pwc readexe record reset restart rm save securelogin show stamp stop system tic type unmount xmodem The Sub Contexts section lists the objects that you can add from your current location in the device configuration tree Figure 2 4 303562 A Rev 00 Getting Started with the BCC er reate OSPF automatically IGMP RDISC with IP Figure 2 4 BCCO019A Objects You Can Configure a
18. interval 5 ospf 1 2 3 4 303562 A Rev 00 3 9 Using the Bay Command Console BCC Disabling Reenabling and Deleting a Configured Object Table 3 2 lists the commands you can use to disable reenable and delete any configured object To use these commands you must be in configuration mode with read write privileges Table 3 2 BCC Commands Command Function disable Change the state of a configured object from enabled to disabled as follows ip 1 2 3 4 255 0 0 0 disable You can accomplish the same change by assigning the value disabled to the state parameter of an object that you want to disable enable Change the state of a configured object from disabled to enabled as follows ip 1 2 3 4 255 0 0 0 enable You can accomplish the same change by assigning the value enabled to the state parameter of an object that you want to reenable delete Delete the object identified in the BCC context sensitive prompt For example the following command deletes an IP interface address 1 2 3 4 ip 1 2 3 4 255 0 0 0 delete CAUTION Deleting an object at one level of the configuration tree causes the BCC to automatically delete any branches configured on that object For example if you delete an IP interface the BCC deletes any protocols such as RIP ARP or OSPF configured on that interface Creating and Using BCC Command Files You can save BCC commands to an ASCII file edit the file add c
19. level back one or more levels closer to root level of the device configuration tree you can enter the full BCC instance ID of the desired object as follows Example go back one level rip 192 168 125 34t ip 192 168 125 34 255 255 255 224 ip 192 168 125 34 255 255 255 224 2 4 303562 A Rev 00 Getting Started with the BCC Example go back two levels rip 192 168 155 151 ethernet 2 1 ethernet 2 1 In the second example the BCC searches back toward root until it finds a context or level where the object you specified in this case ethernet 2 1 exists in the router configuration tree The BCC enters the context of this object and the prompt displays your new location Moving Back to Root Level You can move back to root level in configuration mode by entering the name of the object at that level For an AN ANH ARN or BN router enter ip 1 2 3 4 box box For an ASN or System 5000 router enter ip 1 2 3 4 stack stack Moving Forward One or More Levels To move from your current working level to the next configured level Figure 2 1 enter the BCC instance ID of the desired object as follows Example box ethernet 2 1 ethernet 2 1 aip 1 2 3 4 255 0 0 0 ip 1 2 3 4 255 0 0 0 rip rip 1 2 3 4 Notice that a slash character joins the name and any required parameter values to make a BCC instance ID for any configured object 303562 A Rev 00 2 5 Using the Bay Command Console
20. on the same volume config read write read only Enter BCC configuration mode If you v v logged on as Manager you have BCC only read write access to the device configuration if you logged on as User you have read only access which allows you to display the existing configuration but prevents you from changing the configuration If you enter BCC configuration mode as Manager and want to change your privilege level for the current session from read write to read only enter config read only To change Manager privileges back to read write enter config read write copy lt vol gt lt filename1 gt lt vol gt lt filename2 gt Copy the contents of the first file to the VY second file Technician Interface only cp lt vol gt lt filename1 gt lt vol gt lt filename2 gt Copy the contents of the first file to the VY second file BCC only date lt mm dd yy gt lt hh mm ss gt Display or update the system time and VY VY lt hh mms time zone delete lt filename gt lt volume gt Delete the file from the specified volume f Technician Interface only see rm for BCC equivalent continued 303562 A Rev 00 Using the Bay Command Console BCC Table A 1 System Commands continued Login Access Privileges Command Purpose Manager User delete lt BCC_instance_ID gt Delete the object described in the current prompt or delete the object
21. registered trademarks are the property of their respective owners Restricted Rights Legend Use duplication or disclosure by the United States Government is subject to restrictions as set forth in subparagraph c 1 4i of the Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 Notwithstanding any other license agreement that may pertain to or accompany the delivery of this computer software the rights of the United States Government regarding its use reproduction and disclosure are as set forth in the Commercial Computer Software Restricted Rights clause at FAR 52 227 19 Statement of Conditions In the interest of improving internal design operational function and or reliability Bay Networks Inc reserves the right to make changes to the products described in this document without notice Bay Networks Inc does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein Portions of the code in this software product may be Copyright 1988 Regents of the University of California All rights reserved Redistribution and use in source and binary forms of such portions are permitted provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation advertising materials and other materials related to such distribution and use acknowledge that such portions of the software were developed b
22. sequence of objects between root level and the desired context Example help ip ospf Hint Use the help tree all command to determine the path to the desired object help syntax Get Help on symbols used to express BCC command syntax help tree List in hierarchical format all objects configurable on the current object help tree all List in hierarchical format all objects configurable on this device info List values currently assigned to parameters of this object lt object gt Get command usage Help and list parameters of an object you can add or modify from your current location lt parameter gt Get the current value for this parameter of the current object lt parameter gt Get legal current and default values for this parameter of the current object 2 12 303562 A Rev 00 Getting Started with the BCC Help Command Examples This section provides examples of how you can use the Help commands to get BCC information Listing Objects You Can Configure To list the objects you can configure from the current location enter the help tree command Example ethernet 2 1 help tree The configuration tree below this context is ip arp rip ospf neighbor rdisc igmp relay ipx rip sap static route adjacent host static service route filter server network filter server name filter auto neg You can also use the output of the help tree all command to
23. you deleted the object ethernet 13 1 lso no objects listed Note that ip 192 168 133 114 255 255 255 224 no longer appears in the list of objects configured on ethernet 13 1 With a single delete command the BCC automatically deleted the branch objects arp 192 168 133 114 1 and rip 192 168 133 114 configured on ip 192 168 133 114 255 255 255 224 You can also delete an object from its parent context using the following syntax delete lt BCC_instance_identifier gt Example ip 1 2 3 4 255 0 0 0 delete rip 1 2 3 4 ip 1 2 3 4 255 0 0 0 303562 A Rev 00 4 17 Using the Bay Command Console BCC Using this method you remain in the current context after deleting the branch object 4 18 303562 A Rev 00 Appendix A System Commands The BCC supports the system commands listed in Table A 1 For more detailed information about any of these commands e Enter help lt command gt at any BCC prompt for example help save e Refer to the guide Using Technician Interface Software 303562 A Rev 00 A 1 Using the Bay Command Console BCC Table A 1 System Commands Login Access Privileges Command Purpose Manager User List the names of objects parameters v v and system commands you can enter next lt command gt Display syntax usage Help for lt command gt lt object gt List parameters of an object you can access or configure from your c
24. 1 2 3 4 enable rip 1 2 3 4 3 Verify that you reenabled RIP rip 1 2 3 4 state state enabled rip 1 2 3 4 You can also enable an object from its parent context using the following syntax enable lt BCC_instance_identifier gt Example ip 1 2 3 4 255 0 0 0 enable rip 1 2 3 4 ip 1 2 3 4 255 0 0 0 Using this method you remain in the current context after enabling the branch object 4 16 303562 A Rev 00 Tutorial Configuring a Network Device Deleting a Configured Object Because of the tree hierarchy objects on higher branches of the tree depend on the state and existence of objects closer to the root of the tree Deleting an object also deletes anything configured on that object Caution Before using the BCC to delete an interface make sure that you did not use Site Manager to configure it with a protocol that the BCC does not recognize If you did use Site Manager to delete the interface Here is a BN router example of how to delete an IP interface from the active device configuration 1 Navigate to the object you want to delete box ethernet 13 1 ethernet 13 1 ip 192 168 133 114 255 255 255 224 ip 192 168 133 114 255 255 255 224 2 List all objects configured on the current object ip 192 168 133 114 255 255 255 224 lso arp 192 168 133 114 1 rip 192 168 133 114 3 Delete the object ip 192 168 133 114 255 255 255 2244 delete ethernet 13 14 4 Verify that
25. BCC box box eth 2 1 Starting context gt ethernet 2 1 ethernet 2 1 ip 1 2 3 4 255 0 0 0 ip 1 2 3 4 255 0 0 0 ip 1 2 3 4 255 0 0 0 rip rip 1 2 3 4 Ending context rip 1 2 3 4 BCC0014B Figure 2 1 Moving Away from Root Level Moving to Any Context in the Device Configuration To navigate to any configured object you can specify a full or absolute path from root box Or stack level at any prompt When you enter a path specify the BCC instance identifier of each object Example To move from ip 192 168 33 66 255 255 255 0 on ethernet 2 1 to rip 1 2 3 4 on ethernet 2 2 Figure 2 2 enter the following command ip 192 168 33 66 255 255 255 0 box ethernet 2 2 ip 1 2 3 4 255 0 0 0 rip rip 1 2 3 4 2 6 303562 A Rev 00 Getting Started with the BCC ethernet 2 2 ip 1 2 3 4 255 0 0 0 rip 1 Ending context i Se da pean ee ee De i BCC0009B Figure 2 2 Navigating to an Object in the Configuration The BCC can automatically search backward recursively toward root level until it finds a level where the object you specify first in the command line exists in the device configuration tree Example To move from ip 192 168 33 66 255 255 255 0 on ethernet 2 1 to rip 1 2 3 4 on ethernet 2 2 enter the following command ip 192 168 33 66 255 255 255 0 ethernet 2 2 ip 1 2 3 4 255 0 0 0 rip rip 1 2 3 4 In this example the BCC searches backward to find ethernet 2 2 specified f
26. IMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Licensee is responsible for the security of 303562 A Rev 00 iii its own data and information and for maintaining adequate procedures apart from the Software to reconstruct lost or altered files data or programs 4 Limitation of liability INNO EVENT WILL BAY NETWORKS OR ITS LICENSORS BE LIABLE FOR ANY COST OF SUBSTITUTE PROCUREMENT SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE SOFTWARE EVEN IF BAY NETWORKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN NO EVENT SHALL THE LIABILITY OF BAY NETWORKS RELATING TO THE SOFTWARE OR THIS AGREEMENT EXCEED THE PRICE PAID TO BAY NETWORKS FOR THE SOFTWARE LICENSE 5 Government Licensees This provision applies to all Software and documentation acquired directly or indirectly by or on behalf of the United States Government The Software and documentation are commercial products licensed on the open market at market prices and were developed entirely at private expense and without the use of any U S Government funds The license to the U S Government is granted only with restricted rights and use duplication or disclosure by the U S Government is subject to the restrictions set forth in subparagraph c 1 of the Commercial Computer Software Restricted Rights
27. Telnet Some protocols such as IP RIP and OSPF have global and interface level objects 303562 A Rev 00 1 7 Using the Bay Command Console BCC Physical Device Objects The following sections provide BCC terms for the physical device Box The BCC uses the term box to identify the chassis for a Bay Networks nonstackable device Every box has a type parameter the value assigned to the type parameter identifies the type of Bay Networks device For example the type parameter has the value an for an AN router and the value frecn for a BCN router with a FRE controller module Board The BCC uses the term board or module to identify any logic or circuit board ina Bay Networks device Each board typically occupies a s ot in a network device On some Bay Networks products one board may contain another board such as an RMON data collection module DCM All board objects have a type parameter that identifies the module type For example qenf is the value of the type parameter for a Quad Ethernet with hardware filters module Note For module descriptions based on the literal value of the type parameter for any board object see the Release Notes Slot The BCC uses the term slot to identify the location as well as a physical and electrical means for attaching modules to logic and power connections available on the device chassis e Multislot devices such as the BLN or BCN router accommodate one syst
28. a aa aai 1 10 Chapter 2 Getting Started with the BCC Entering and Exiting the BOG NETTER uansasasenvsameno m ni 2 1 DEPE RT ETE 2 3 Navigating in Configuration ModE soiesicusctortinc sere nnen snes tuacenen iincdnionl iandien dd 2 3 Navigating with the back Command 2 cccccceceeeeeeeeeeeceeeeeaeeeeeeeseeeeeeeeeeeeseeeennaees 2 3 Navigating with Configuration Commands PPEP E ETA ENE 2 4 303562 A Rev 00 V Moving Back One or More Levels acciccsisiccssssssicacesvsiicadunsiidicezenisstetespneseereneet 2 4 Moving Back to FOT Level icc cadssnsteamsrtnutsaannnddi cndeaauptuandanletiamdasauteaaadinitl caxaaientn 2 5 Moving Forward One or More Levels Lumsemenemminennmesuhmuemnonsmeaninonssmenind 2 5 Moving to Any Context in the Device Configuration rrrrrnnnnnnnvvrnnnnnnnnrnnnnnnnnnnn 2 6 BIE se Coniguraton oe Ue lage a earn etter RT a 2 8 Displaying the Total Device Configuration ececccceeeeeccceeeseeeeceeeeeneeeeeeeeneeeeeenenees 2 8 Displaying the Configuration of One Object eccceeeeceeeeceeeeeeeceseeeeeeeesneeeseeteneeees 2 10 EE TUE RR RE REE E E aR 2 11 Help GOMMENdg noni ES 2 11 Heip Command Examples EEE due rsiadiudecescsaguen 2 13 Chapter 3 Entering Commands and Using Command Files SEE Se Renner er ere eer re art ee enn et ree eee re errr mere rete er eee 3 1 Using Command ADpreviatons serisinin aa ei aea E Recalling Commands sessen E 3 2 Editing Command CNES sonrisas ET 3 3 Ente
29. ange the value of any parameter that is part of a BCC instance ID you must first delete the object then re create it with the desired parameter values In this case you must delete the IP interface and then re create it on ethernet 13 1 using the mask value of 255 255 255 224 as follows ip 192 168 133 114 255 255 255 0 delete ethernet 13 1 ip 192 168 133 114 255 255 255 224 ip 192 168 133 114 255 255 255 224 10 Check to see what you can configure at this level ip 192 168 133 114 255 255 255 224 Sub Contexts arp igmp ospf rdisc rip Parameters in Current Context address cost name address resolution end station support on all subnet broadcast has proxy assocaddr host cache aging redirects broadcast mask state cache size mask reply udp checksum configured mac address mtu discovery System Commands You can modify values currently assigned to parameters of ip 192 168 133 114 255 255 255 224 or you can add RIP OSPF Router Discovery or IGMP to this interface 11 Add RIP as the routing protocol by default RIP1 on this interface ip 192 168 133 114 255 255 255 224 rip rip 192 168 133 114 303562 A Rev 00 4 9 Using the Bay Command Console BCC 12 Return to root box level to configure global system services rip 192 168 133 114 box box 13 Check which global services and interfaces you can configure at this level box Sub Contexts atm fddi ipx serial virtual backup pool ftp isdn
30. are Licensee a personal nonexclusive nontransferable license a to use the Software either on a single computer or if applicable on a single authorized device identified by host ID for which it was originally acquired b to copy the Software solely for backup purposes in support of authorized use of the Software and c to use and copy the associated user manual solely in support of authorized use of the Software by Licensee This license applies to the Software only and does not extend to Bay Networks Agent software or other Bay Networks software products Bay Networks Agent software or other Bay Networks software products are licensed for use under the terms of the applicable Bay Networks Inc Software License Agreement that accompanies such software and upon payment by the end user of the applicable license fees for such software 2 Restrictions on use reservation of rights The Software and user manuals are protected under copyright laws Bay Networks and or its licensors retain all title and ownership in both the Software and user manuals including any revisions made by Bay Networks or its licensors The copyright notice must be reproduced and included with any copy of any portion of the Software or user manuals Licensee may not modify translate decompile disassemble use for any competitive analysis reverse engineer distribute or create derivative works from the Software or user manuals or any copy in whole or in part Except a
31. attached to a modem and modem leads are enabled Number of lines that the serial port displays before displaying the more prompt Setting of the Technician Interface more feature Enabled or Disabled according to the MIB record The Technician Interface more command affects only the current login session it does not change the MIB and so does not affect the setting of this field Technician Interface prompt Maximum number of login retries relevant only if modem control is enabled This value determines the maximum number of failed login attempts that a system allows on the serial port If the maximum occurs the system hangs up on the line causing a modem connection to lose carrier detect Number of minutes allowed between when the system displays the login banner and a user enters a login ID relevant only if modem control is enabled If this timeout occurs the system hangs up on the line Number of minutes allowed to enter a password If this timeout period expires the system hangs up on the line Command line timeout value relevant only if modem control is enabled If you do not enter a command in this number of minutes the system hangs up on the serial port Switch to execute control C to break out of the user autoscript When a user autoscript is in effect and this parameter is enabled you can break out of the script when logged in as User but not as Manager Also if this parameter is enabled and the script ter
32. bbreviate BCC instance identifiers Specifying Parameter Values You must specify each parameter value in the form of a parameter value pair Each pair is a command argument pertaining to the object named first in the command line For example the following command changes the BOFL timeout interval to 4 seconds on ethernet 1 1 box ethernet 1 1 bofl timeout 4 bofl timeout 4 is the parameter value pair Required Derived and Other Parameters The BCC indicates when parameter values are required you must supply a value or derived the BCC supplies a value For all other parameters the BCC supplies a default value that you can change Specifying Multiple Parameter Value Pairs You can specify parameter values as follows e Enter an object name and one parameter value pair per command line e Enter an object name and multiple parameter value pairs each pair separated by a space on the same command line 3 8 303562 A Rev 00 Entering Commands and Using Command Files Example In the following example you specify one parameter value pair on each command line box ethernet 2 1 ethernet 2 1 bofl retries 6 ethernet 2 1 bofl timeout 7 ethernet 2 1 hardware filter enabled ethernet 2 1 Example In the following example you specify multiple parameter value pairs on each command line ethernet 2 1 ip address 1 2 3 4 mask 255 255 255 0 redirects off ip 1 2 3 4 255 255 255 0 ospf area 2 3 4 54 hello
33. ble e Init Initializing Up Available Port Name Name that the system assigns to the port You cannot specify a name You can use the name to correlate a port number to a physical port The name of the port should be printed next to the physical port connection for example Port 1 CONSOLE The names do not specify the port s use All ports are serial ports used for Technician Interface sessions only For example port MODEM1 may be a modem connection or a dummy terminal connection depending on its configuration Although port 4 is called PRINTER it is exactly like ports 1 2 and 3 Port 4 doesn t support a printer Port 4 is called PRINTER only because that label is printed near the port connector on the link module Slot Number Slot on which the login session for the serial port is running Baud Rate Current baud rate setting for the serial port Data Bits Number of data bits in the serial port s configuration C 2 303562 A Rev 00 System show Commands Parity Stop Bits Modem Enable Lines Screen More Enable Port Prompt Login Retries Login Timeout min Password Time Out Command Time Out User Abort Logout Initial Search Path Serial port s current parity setting Number of stop bits in the serial port s configuration Configuration of modem control as follows e Disabled Port is directly connected to a device such as a dummy terminal or a terminal server Enabled Port is
34. can enter lt BCC_instance_ID gt lt parameter gt Get legal current and default values for this parameter of a configured object that you can access from your current working context Example box ethernet 2 1 bofl Current Value enable Legal Value enable disable Default Value enable lt commana gt Display usage Help or next level options for a command lt commana gt lt option gt Display next level options for this command or any arguments available to limit the output from this command help Get an overview of Help oriented command features help lt commana gt Get full details of a specific command help commands Display the syntax of all BCC commands in alphabetical order help commands more Display the syntax and brief command descriptions for all BCC commands in alphabetical order help editing Get Help on how to edit BCC commands and command lines help learning bcc Get Help on performing common BCC operations help lt object_name gt Show usage and parameter Help for this object help lt parameter_name gt Show usage Help for this parameter continued 303562 A Rev 00 Using the Bay Command Console BCC Table 2 1 BCC Help Commands continued Command Help Feature help lt path gt lt object_name gt Describe parameters of an object outside the current context lt path gt is the
35. cified slot If the slot ID argument is absent reboot the entire device restart lt slot ID gt Restart the GAME image on the v specified slot If the slot ID argument is absent the GAME image restarts on all slots continued 303562 A Rev 00 System Commands Table A 1 System Commands continued Login Access Privileges Command Purpose Manager User rm lt vol gt lt filename gt Remove delete the file from the VY specified volume BCC only save config aliases log Store the current configuration alias list S lt vol gt lt filename gt or system event securelogin Turn SecurID access to the device on VY and off via Telnet set lt obj name gt lt obj id gt lt attr_name gt Modifies data objects in the MIB VY lt attr id gt lt inst_id gt lt value gt Technician Interface only show config all Show the total configuration of the device VY use all or the total configuration of the BCC only current object omit all source lt vol gt lt filename gt Read BCC configuration commands from a text file dynamically changing the BCC configuration mode only active device configuration source aliases env perm Read a list of aliases environment VY lt vol gt lt filename gt variables or dynamic permissions from a Technician Interface only file stamp Display the device image version name v and timestam
36. d type values such as qenf see the Release Notes 303562 A Rev 00 2 9 Using the Bay Command Console BCC Displaying the Configuration of One Object To view objects configured within a specific part of the BCC configuration tree enter the show config command or the Iso command Example To view the configuration of a specific configured object navigate to the object and enter the show config command The following example shows all objects configured on ethernet 2 1 of a BLN router box eth 2 1 ethernet 2 1 show config ethernet slot 2 connector 1 circuit name E21 alpha ip address 192 168 125 34 mask 255 255 255 224 broadcast 192 168 125 32 arp back rip back back back Example You can also enter the Iso command to view any instances of objects configured at your current location in the active device configuration as follows ip 192 168 155 151 255 255 255 0 1so arp 192 168 155 151 1 rip 192 168 155 151 Use the Iso command if you have no need to display the contents of the current object in full BCC configuration syntax 2 10 303562 A Rev 00 Getting Started with the BCC Using Online Help This section describes how to use BCC online Help Help Commands Table 2 1 lists the commands you use to access BCC online Help Table 2 1 BCC Help Commands Command Help Feature List the names of all objects and parameters you can configure and the system commands you
37. d values lt parameter gt lt value gt is any parameter value pair you can optionally customize for an object you specify in a BCC command line Using Default Syntax Using default syntax you do not need to enter the name of a required parameter you enter only its value at the proper location in the command line For example the default syntax for configuring an Ethernet interface on an AN ANH ARN or BN router is ethernet lt s ot gt lt connector gt The following commands are equivalent Using full syntax box ethernet slot 2 connector 1 ethernet 2 1 Using default syntax box ethernet 2 1 ethernet 2 1 Using Abbreviated Syntax You can abbreviate BCC configuration commands as follows Example box eth 2 1 This command is the same as the following two commands box ethernet slot 2 connector 1 box ethernet 2 1 303562 A Rev 00 3 7 Using the Bay Command Console BCC If you press Return before entering a sufficient number of characters for the BCC to recognize the name of the object or parameter you want to configure the BCC returns an error message Example box e ambiguous command name e enable eof error ethernet eval exit expr The BCC returns a list of all the commands available in the current context that start with the letter e Choose one command from the list and enter enough characters for the BCC to recognize that command when you press Return You cannot a
38. e Enter show ip alerts routes Example Use the dinfo command braces 1 Indicate required elements in syntax descriptions where there is more than one option You must choose only one of the options Do not type the braces when entering the command Example If the command syntax is show ip alerts routes you must enter either show ip alerts or show ip routes brackets Indicate optional elements in syntax descriptions Do not type the brackets when entering the command Example If the command syntax is show ip interfaces alerts you can enter either show ip interfaces or show ip interfaces alerts ellipsis points Indicate that you repeat the last element of the command as needed Example If the command syntax is ethernet 2 1 lt parameter gt lt value gt you enter ethernet 2 1 and as many parameter value pairs as needed xiv 303562 A Rev 00 Preface italic text screen text vertical line 1 Indicates file and directory names new terms book titles and variables in command syntax descriptions Where a variable is two or more words the words are connected by an underscore Example If the command syntax is show at lt valid_route gt valid_route is one variable and you substitute one value for it Indicates system output for example prompts and system messages Example Set Bay Networks Trap Monitor Filters Separates choices for command keywords and a
39. e only see Appendix A System Commands e Execute configuration commands to perform tasks such as creating or deleting IP interfaces on the router Enter BCC configuration mode by entering the config command at the bec gt prompt Note For a list of services you can configure using the BCC see the Release Notes You can obtain a complete hierarchical listing of all objects configurable on a device by entering the help tree all command at any BCC prompt Platform Requirements The BCC runs on AN ANH ARN ASN System 5000 and BN platforms including ARE FRE and FRE 2 processor modules Each slot must have e 16 MB of dynamic RAM DRAM e 2 MB of free memory space available when you start the BCC If you try to start the BCC with insufficient DRAM or free memory on a slot the BCC returns an error message In that case use Site Manager instead of the BCC Number of BCC Sessions You can open one BCC session per slot in read write configuration mode Other users can open additional BCC sessions in read only nonconfiguration mode on the same slot depending on available memory Each BCC session is mutually exclusive If you make a change during a BCC session in read write mode this change does not appear in other BCC sessions 303562 A Rev 00 Overview of the BCC Terminology and Concepts This section describes key terms and concepts of the BCC interface Configuration Hierarchy The BCC c
40. em SRM L or link interface module per slot e Single slot devices such as the AN ASN and ARN routers accommodate one base module in slot 1 one or two adapter modules and one expansion module 303562 A Rev 00 Overview of the BCC Connector The BCC uses the term connector to identify the physical and electrical means to interconnect a network device directly or indirectly to a physical layer transmission medium Line The BCC uses the term line to identify the physical and in some cases logical circuit identified typically by means of a slot connector interface type ethernet sync fddi and so on and where applicable a channel number such as with T1 E1 interface types Port The BCC uses the term port to identify an interface object defined by its type for example an Ethernet port and location slot and connector within a network device On a network device a port is also a logical point of termination for data sent or received by a specific protocol or application Interface The BCC uses the term interface to identify circuitry and digital logic associated with the interconnection between a physical network medium such as Ethernet and a higher layer protocol entity such as IP Note A logical interface is an addressable entity for originating and terminating connections across an IP network 303562 A Rev 00 1 9 Using the Bay Command Console BCC Parameters A paramete
41. es you to enter a mask value whenever you create an IP interface Because the first octet of the address is 192 OxCO this is a Class C address requiring the first 3 octets to be the network portion of the interface address You can express the corresponding mask value as either 255 255 255 0 using dotted decimal notation or 24 the number of bits making up the network portion of the IP interface address as follows ethernet 13 1 ip 192 168 133 114 24 ip 192 168 133 114 255 255 255 0 The BCC converts the integer representing the number of mask bits into a dotted decimal mask value as shown in the last prompt 8 Check the values currently assigned to parameters of IP on this interface ip 192 168 133 114 255 255 255 0 info state enabled address 192 168 133 114 mask 255 255 255 0 assocaddr 0 0 0 0 cost 1 broadcast 0 0 0 0 configured mac address 0x mtu discovery off mask reply off all subnet broadcast off address resolution arp proxy off host cache aging cache off udp checksum on end station support off redirects on cache size 128 4 8 303562 A Rev 00 Tutorial Configuring a Network Device 9 Change the subnet mask to 255 255 255 224 ip 192 168 133 114 255 255 255 0 mask 255 255 255 224 mask parameter may not be modified ip 192 168 133 114 255 255 255 0 You cannot modify any parameter values included in the BCC instance ID of a configured object in this case ip 192 168 133 114 255 255 255 0 To ch
42. ess Used Percentage of CPU time used by each process Idle CPU idle time in hundredths of seconds Max Total CPU time in hundredths of seconds list detail total Displays a list of all the processes running on each slot show process list detail total The table includes the following information Name The name of the process Slot Slot number C 8 303562 A Rev 00 System show Commands memory detail total Displays the number of bytes and the percentage of memory used by all processes on the router detail Displays details about the amount of memory used by each process running on the router total Displays only memory usage totals The table includes the following information Name The name of the process if you specify the detail option Slot Slot number Used Number of memory bytes used by each process Used Percentage of memory used by each process Free Number of free buffers on this slot if you specify the total option 303562 A Rev 00 C 9 Using the Bay Command Console BCC show system The show system lt option gt commands display information about the overall system state The show system command supports the following subcommand options buffers memory drivers protocols information tasks buffers drivers Displays the current buffer usage for all active slots on the router Because buffers circulate rapidly through the system a low f
43. fficient number of characters for the BCC to recognize that name uniquely Example box eth 5 1 ethernet 5 1 back box tf tftpt You can abbreviate system commands for example the BCC recognizes sh as show in contexts where there are no other commands configurable objects or parameter names that also start with sh Recalling Commands The BCC supports a configurable command history buffer from which you can recall commands recently entered The command history buffer contains up to 20 commands by default You can increase the number of commands in the history buffer to a maximum of 40 by setting new values for the history parameter of the console and telnet objects Example box telnet telnet server server history 30 server history history 30 server box box console portnum 1 console 1 history 30 console lt Recall commands from the history buffer as follows e To recall the previous command press the up arrow key or press Control p e To recall the next command press the down arrow key or press Control n 3 2 303562 A Rev 00 Entering Commands and Using Command Files Editing Command Lines Table 3 1 describes the keystrokes you can use to edit BCC command lines Table 3 1 Keystrokes for Editing BCC Command Lines Editing Function Keystrokes Move the cursor left CONTROL b or left arrow key Move the cursor right CONTROL f or rig
44. ger User help commands Display an alphabetical list of all commands with syntax and terse descriptions v v help commands more Display syntax and brief command descriptions for all BCC commands in alphabetical order v help lt object name gt Display definitions for parameters of the currrent object For example help ip ospf defines parameters of the global ospf object and help ethernet ip defines parameters of the IP interface on an Ethernet port help lt parameter name gt Display definitions of all parameters of the current object For example help bofl displays the definitions of all parameters of ethernet help syntax Display Help on how to interpret BCC syntax symbols help lt task gt Display Help on how to perform a specific task The help commands are help learning bec and help editing help tree all Display a hierarchical list of all objects you can configure on this platform use all or on the current object omit all v continued 303562 A Rev 00 Using the Bay Command Console BCC Table A 1 System Commands continued Login Access Privileges Command Purpose Manager User help lt commana gt all The help command entered without v v arguments at the Technician Interface Technician Interface only prompt displays an alphabetical list of all commands wi
45. he total device configuration Each instance is identified by its BCC instance identifier BCC Instance Identifier A BCC instance identifier uniquely identifies a single instance of an object configured on a device The BCC instance ID consists typically of the name of the object combined with the values you specify for its required parameters For example the BCC instance ID for an Ethernet interface on a BN platform consists of ethernet lt slot gt lt connector gt as in ethernet 2 1 For some objects the BCC automatically appends an internally generated number to ensure the uniqueness of the BCC instance ID For example the BCC creates an instance ID for ARP on IP based on the object name arp plus the address of the underlying IP interface 1 2 3 4 plus an internally generated integer resulting in an ID such as arp 1 2 3 4 1 In other rare cases a configurable object may also have required parameters that do not become part of its BCC instance ID For example the global OSPF object has a required router id parameter that does not become part of the instance ID Many such required parameters end in id such as global id and router id Each object has its own requirements for unique instance identification within the total device configuration Global Box Wide Objects Global or box wide objects provide services uniformly to all slots of a network device Examples include global IP BGP TCP SNMP FTP TFTP and
46. ht arrow key Delete the current line CONTROL u Delete the word at the cursor location CONTROL w Delete the character at the cursor location CONTROL d Move the cursor to the beginning of the line CONTROL a Move the cursor to the end of the line CONTROL e Toggle insert mode CONTROL 0 Delete previous character BKSP or DEL or CONTROL h Interrupt CONTROL c Start echo to the screen CONTROL q Stop echo to the screen CONTROL s Recall previous command CONTROL p or up arrow key Recall next command CONTROL n or down arrow key For example use the up arrow key or Control p to retrieve your last input then use other control key combinations to edit the command line as needed 303562 A Rev 00 Using the Bay Command Console BCC Entering Multiple Commands on a Line To enter multiple commands on the same line type a semicolon wherever you would press Return to terminate a command Example Configure ethernet 2 1 from root then configure ip 1 2 3 4 255 0 0 0 on ethernet 2 1 and RIP on ip 1 2 3 4 255 0 0 0 as follows box ethernet 2 1 ip 1 2 3 4 255 0 0 0 rip rip 1 2 3 4 Continuing a Command Line You can continue a command line by entering a backslash character at the end of the current text line The BCC treats characters on the next physical line as part of the same BCC logical command line You must immediately follow the backslash with a newline Return character
47. ing amp Conigured OG Vaset a i aiaiai 4 15 Enabling Configured DN sca catvicnecixstccmnsteserigineetsctaaanedeaiendsreanieinnasannacniawn cusnawe 4 16 Deleng a Configured Ope ssrissseniarisiiasiirsi iniisa Na AENEAN E E 4 17 Appendix A System Commands Appendix B TCL Support Appendix C System show Commands SEN COBO EE EE a a C 2 S AAN n E bee iuesminetatannenaum C 5 ee a a C 7 SO Se I EE 0 TEN o EE ent det C 10 Appendix D Syntax for Module Location Index 303562 A Rev 00 vii Figures Figure 1 1 The Technician Interface and the BCC Interface s es 1 1 Figure 1 2 Sample BCC Configuration cccreinccceneooscccansoonsccianavonncainavedacdiannvoadiniannnnccaan 4 Figure 1 3 Configuring IP and RIP on an Eihemet martane EE 1 5 Figure 1 4 Configuring IP and RIP on an Ethernet Interface mrnrrnnnrronrrnrrnnrnnnenn 1 6 Figure 2 1 Moving Away from Root Level a se EE EE 2 6 Figure 2 2 Navigating to an Object in the Goniigaraton AAEE 2 7 Figure 2 3 Navigating with the BCC Recursive Search Feature eceeeeeee 2 8 Figure 2 4 Objects You Can Configure at the Next Level cssceeseeeeesteeeeeees 2 15 Figure 4 1 Sample BCC Configuration BCN Router essssssessseesseessseesseesrresreessnns 4 3 Figure 4 2 Typical BCC Configuration Cycle smette 4 4 303562 A Rev 00 ix Tables Table 2 1 BOG Hep GOMMAN rirnan Aa 2 11 Table 3 1 Keystrokes for Editing BCC C
48. irst in the command line and then moves sequentially to the other locations ip 1 2 3 4 255 0 0 0 and rip specified next in the command line 303562 A Rev 00 2 7 Using the Bay Command Console BCC Starting context ethernet 2 1 ip 192 168 33 66 255 255 255 0 BCC0009C Figure 2 3 Navigating with the BCC Recursive Search Feature Displaying Configuration Data To display Bay Networks device configuration commands and data use the show config command Displaying the Total Device Configuration The show config all command displays the entire device configuration from any BCC prompt The output of this command describes Existing objects Objects that the BCC automatically added to the active device configuration Navigation back commands necessary to move to the context of the previous object configured or to return to the root level of the active device configuration 2 8 303562 A Rev 00 Getting Started with the BCC Example bcc gt show config all box type freln board slot 1 type srml back board slot 2 type qenf back board slot 3 type wffddi2m ethernet slot 2 connector 1 circuit name E21 alpha ip address 192 168 3 4 mask 255 255 255 224 broadcast 192 168 3 5 rip back arp back back back ftp default volume 2 back snmp community label public access read write manager address 0 0 0 0 back manager address 192 168 9 9 Note For descriptions of all boar
49. known by the BCC configuration read write mode only specified lt D gt and configured previously from the current level diags lt slot ID gt Perform CPU memory backbone and v link diagnostics before downloading the GAME image and rebooting on the specified slot dinfo Display the status of each file system v v volume on this device dir lt vol gt Display the contents of the file system v v volume specified disable Disable the object at your current location f in the BCC configuration tree BCC configuration read write mode only enable Enable the object at your current location f in the BCC configuration tree BCC configuration read write mode only format lt volume gt Erase the entire contents of the file v system volume specified and reinitialize it to a usable state get lt obj name gt lt obj id gt lt attr name gt Retrieve the values of data objects in the VY lt attr_id gt lt inst_id gt MIB Technician Interface only getcfg Display network boot parameters v v Display the current parameter settings Technician Interface AN routers only used to determine the source of image and configuration files help Display an overview of BCC v v Help oriented features help lt command gt Display detailed Help on a specific v v command continued 303562 A Rev 00 System Commands Table A 1 System Commands continued Command Purpose Login Access Privileges Mana
50. lements lt object name gt lt required_parameter gt lt value gt lt parameter gt lt value gt lt parameter gt lt value gt The BCC requires input for any elements enclosed by braces lt object name gt is the name of an object you want to configure for example ip The BCC assumes that an object you specify is new and will create it if it is not in the current configuration If an object you specify already exists in the current configuration the BCC assumes that you want to modify that object lt required parameter gt lt value gt is any parameter value pair required to uniquely identify an object you specify in a BCC command line An object may have one or more required parameters For example the full syntax for configuring an Ethernet interface on an AN ANH ARN or BN router is ethernet slot lt s ot_no gt connector lt connector no gt On an ASN or System 5000 router the full syntax is ethernet slot lt s ot no gt module lt module_no gt connector lt connector no gt 3 6 303562 A Rev 00 Entering Commands and Using Command Files Note You cannot change the value of a parameter used by the BCC to create an instance identifier For example you cannot modify the address value assigned to an IP interface To change the value of any required parameter you must delete the associated object and then add it back into the device configuration with new require
51. level from read only to read write if you logged in as User Caution When you enter BCC configuration commands with read write privileges you immediately modify the device configuration When you finish using BCC configuration mode enter the exit command at any prompt box exit bec gt When you finish using the BCC enter the exit command at the bcc gt prompt bec gt exit Routerl gt Exiting the BCC returns you to the Technician Interface prompt For more detailed information about Technician Interface access login or logout procedures see Using Technician Interface Software 303562 A Rev 00 Getting Started with the BCC Displaying Context In configuration mode the BCC displays a context sensitive prompt The prompt identifies the configured object at your current working location within the configuration hierarchy For example after logging in to a BLN router as Manager then configuring or navigating to the Ethernet interface on slot 2 connector 1 the BCC displays the following prompt ethernet 2 1 To display the complete path from root level to your current level in the device configuration tree enter the pwe print working context command Example rip 192 168 125 34 pwe box ethernet 2 1 ip 192 168 125 34 255 255 255 224 rip 192 168 125 34 The pwe command displays the BCC instance identifier of each configured object in the path Navigating in Configuration Mode You can na
52. me gt Display the current system event log v v e lt entity gt f lt severity gt s lt slot ID gt p lt rate gt c lt code gt Follow the optional e flag immediately with the entity name in uppercase characters and enclosed in quotation marks no intervening spaces Specify lt severity gt using letters with no intervening spaces f fault w warning i info t trace d debug Examples fwid ffitd fwi fwitd Use the optional p flag to set an interval for polling the log and displaying the result log x i e lt entity gt f lt severity gt Excludes x or includes i event v v s lt slot ID gt logging indicated by the command options log z s lt slot ID gt Displays current filter setting v v logout Exit the current login session v v Iso 1 List objects configured on the current v v object The optional I flag causes the BCC configuration mode only BCC to list object IDs in wraparound screen format mget lt obj_name gt lt obj id gt Retrieve the values of data objects in the v lt attr name gt lt attr id gt lt inst id gt MIB BCC only mlist instances lt obj name gt List objects in the MIB v v BCC only more on off lt 4 lines per screen gt Set or display the status of the more VY VY utility continued 303562 A Rev 00 A 7 Using the Bay Command Console BCC
53. minates due to an error the system automatically logs you out List of file system volumes to be searched when you run a script without a volume specifier or if an autoscript does not contain a volume specifier The environment variable PATH is set to this string The string format is as follows lt vol gt lt vol gt Example 2 3 4 55 303562 A Rev 00 Using the Bay Command Console BCC stats Manager s Name of the script to run when the Manager account logs in to the AutoScript router If the script name does not contain a volume specifier the system searches the volumes listed in Initial Search Path User s AutoScript Name of the script to run when the User account logs in to the router If the script name does not contain a volume specifier the system searches the volumes listed in Initial Search Path History Depth Maximum number of Technician Interface commands stored in the local command history table The table stores each command you enter at the prompt on a first in first out FIFO basis files to autosave Number of times that the system saves the events log to a new file automatically when the log is full Volume for The target volume where the system stores new log files saved autosave through the log autosave feature Displays login information and console port error statistics The table includes the following information Port Number Port Name Port State Total Logins
54. o parameters of FTP ftp info on box state enabled default volume 2 login retries 3 idle timeout 900 max sessions 3 tcp window size 60000 31 Change the default volume number to 5 ftp def 5 ftp 32 Verify the change to the default volume number ftp def default volume 5 33 Recheck the total device configuration ftp show config all box type frecn board slot 5 type sync back board slot 7 type srml back board slot 9 type dtok back board slot 11 type wffddi2m back board slot 13 type qenf back console portnum 1 prompt slot auto manager script automgr bat auto user script autouser bat back ethernet slot 13 connector 1 circuit name E131 ip address 192 168 133 114 mask 255 255 255 224 remaining configuration not shown here 34 Return to root level ftp box box 4 14 303562 A Rev 00 Tutorial Configuring a Network Device Disabling 35 Save the file using a name other than config until you can test the configuration box save config startup cfg 36 Test the intial IP interface box ping 192 168 133 114 IP ping 192 168 133 114 is alive size 16 bytes 37 Ensure that the initial IP interface connects to another device on the network box ping 192 168 133 97 IP ping 192 168 133 97 is alive size 16 bytes 38 When you finish configuring the router exit configuration mode box exit bec gt 39 Exit the BCC which returns you
55. ollowing example shows a sequence of commands you can use to configure a BCN router on a network You first complete the physical installation of the router then boot the router using the image bn exe and the minimum configuration file ti cfg This example creates the following objects in the total router configuration Figure 4 1 IP global ARP global on IP RIP global on IP SNMP global Community public on SNMP Manager address 0 0 0 0 on community public FTP global TFTP global Telnet global Server global on Telnet Quad Ethernet interface in slot 13 IP interface address 192 168 133 114 on Ethernet connector 1 ARP on IP interface 192 168 133 114 RIPon IP interface 192 168 133 114 Serial interface in slot 5 Dual token ring interface in slot 9 FDDI interface in slot 11 4 2 303562 A Rev 00 Tutorial Configuring a Network Device serial 5 1 Figure 4 1 N m hl ISI IS E allal l l fel fz Cc CE fe I l Jo fo server community public arp rip Global Services manager 0 0 0 0 Sample BCC Configuration BCN Router After you create a diagram of the device configuration tree configure the device using a cycle of BCC configuration commands similar to those shown in Figure 4 2 303562 A Rev 00 Using the Bay Command Console BCC START CONTINUE Current Enter the name of e prompt any changed parameter to verify its new a
56. ommand Lines s s 3 3 Table 3 2 REE a Lae oc E EA emer remem EA emer EAE EE T 3 10 Table A 1 Sysilem Commands sha cecabutteuc iain eoc auntie eee en A 2 Table D 1 Syntax for Specifying Module Location per Device eee cas D 1 303562 A Rev 00 xi Preface The BCC is a command line interface for configuring Bay Networks devices If you are responsible for configuring and managing Bay Networks AN ANH ARN ASN BN BCN and BLN or System 5000 routers read this guide to learn how to use the Bay Command Console BCC Before You Begin This guide is intended for users who have some experience supporting a multivendor internetworking system You should be able to perform network device configuration maintenance and troubleshooting Because the BCC makes real time changes to device configuration Bay Networks recommends that you first learn about BCC behavior on a device not connected to your production network 303562 A Rev 00 xiii Using the Bay Command Console BCC Text Conventions This guide uses the following text conventions angle brackets lt gt Indicate that you choose the text to enter based on the description inside the brackets Do not type the brackets when entering the command Example If the command syntax is ping lt ip_address gt you enter ping 192 32 10 12 bold text Indicates text that you need to enter and command names and options Exampl
57. omments and then use the source command to read the file into the device s active configuration The following sections describe how to complete these tasks 3 10 303562 A Rev 00 Entering Commands and Using Command Files Saving Commands to a File If you log in to a Bay Networks router from a PC or workstation using Telnet or terminal emulation you can use the native capabilities of the PC or workstation to e Save the output of a show config command to an ASCII file e Save a sequence of manually entered BCC commands to an ASCII file You can also use an ASCII text editor on a workstation to create a file from which the BCC can read configuration and system commands Note You can also save the output of the show config command to an ASCII text file on the router by entering show config all file lt volume gt lt filename gt at any BCC prompt Adding Comments to a Command File You can use a text editor such as vi on a UNIX workstation to add descriptive comments to a BCC command file Enter comments in the following format box lt command gt comment or box comment box lt command gt Example box board slot 1 type andse 192 168 47 129 192 168 47 21 When you finish editing the file save it on your workstation or PC The comments are for reference only Comments do not appear in the output of any show config command 303562 A Rev 00 3 11 Using the Bay Command Console BCC
58. onfiguration hierarchy begins at a root level object called box for AN ANH ARN and BN platforms and stack for ASN and System 5000 platforms Under the root level object are branch objects such as interfaces and protocols that fan out from the root level in a tree hierarchy You use the help tree all and show config all commands to display the configuration hierarchy of a Bay Networks router e The help tree all command displays the hierarchy of every object you can configure e The show config all command displays the hierarchy of objects you have configured Figure 1 2 illustrates a sample BCC configuration for an AN BN or ARN router e Box contains the global objects IP SNMP Telnet and TFTP plus the physical interface objects ethernet 2 1 ethernet 2 2 and serial 3 1 e Global IP contains the global objects ARP RIP and OSPF 303562 A Rev 00 Using the Bay Command Console BCC b rooi gt ospf Leni gt protocol gt gt ip protocol gt protocol t gt rip p protocol snmp A protocol 7 gt gt telnet protocol gt gt tftp BOX WIDE GLOBAL OBJECTS protocol Services supported on all slots INTERFACE SPECIFIC OBJECTS Services supported on a specific slot 0spf 1 2 3 4 gt protocol ethernet 2 1 ip 1 2 3 4 255 0 0 0 P interface P protocol
59. onfiguration of the router box show config box type frecn BCN router with a FRE 2 controller 5 board slot 5 type sync Serial link module in slot 5 back board slot 7 type srml System resource module in slot 7 back board slot 9 type dtok Dual token ring link module in slot 9 back board slot 11 type wffddi2m Multimode FDDI link module in slot 11 back board slot 13 type genf Quad Ethernet with filters in slot 13 back console portnum 1 console device on port 1 prompt slot auto manager script automgr bat auto user script autouser bat back back box Note how output of the show config command automatically includes navigation back commands If you save this output to a file you can reenter the commands automatically using the BCC source command See Entering Configuration Commands from a File on page 3 12 For descriptions of the values of the board type parameter see the Release Notes Choose a port interface type slot and connector for the initial IP interface to the router box ethernet slot 13 connector 1 ethernet 13 1 4 6 303562 A Rev 00 Tutorial Configuring a Network Device 6 Check what you can configure sub contexts and parameters at this level ethernet 13 1 Sub Contexts ip ipx Parameters in Current Context bofl bofl number bofl retries bofl timeout bofl tmo divisor System Commands 9 attribute back boot gd
60. onfigured on WAN connector 3 which exists physically on the ARN expansion module BN lt interface gt lt slot gt lt connector gt e lt interface gt Interface type ethernet token ring serial etc e lt slot gt 2 through 5 BLN or 1 through 14 BCN e lt connector gt numbering starts with connector 1 on each slot per media type Example ethernet slot 8 connector 3 This is an Ethernet interface configured on connector 3 of slot 8 of a BCN router System 5000 lt interface gt lt slot gt lt module gt lt connector gt e lt interface gt Interface type ethernet token ring serial atm etc e lt slot_number gt 2 through 13 in a System 5000 chassis e lt module gt numbering corresponds to net module 1 or 2 which plugs into a System 5000 base module A System 5000 base module is always module 3 e lt connector gt numbering starts at 1 on each net module The base module always contains a connector 1 which plugs into a System 5000 backplane for example Ethernet token ring or ATM backplane Example ethernet slot 2 module 2 connector 1 This is an Ethernet interface on connector 1 of the Ethernet net module module 2 in slot 2 atm slot 2 module 3 connector 1 This is an ATM interface on connector 1 of slot 2 a Model 5782 Virtual Network Router VNR base module module 3 Note that the VNR does not accommodate any net modules D 2 303562 A Rev 00 Symbols
61. p system Start a new Technician Interface session f VY that allows you to run system manager Technician Interface only privileged commands telnet d e lt escape_char gt Communicate with other hosts VY VY lt host_ip gt lt port gt supporting the Telnet protocol Technician Interface and BCC top level only not available in BCC configuration mode tftp get put lt address gt Send files to or retrieve files from other lt vol gt lt filename gt lt vol gt lt filename gt hosts supporting TFTP Technician Interface and bcc gt top level only continued 303562 A Rev 00 A 9 Using the Bay Command Console BCC Table A 1 System Commands continued Login Access Privileges Command Purpose Manager User type x lt vol gt lt filename gt Display the contents of the designated VY VY file in ASCII or HEX x format xmodem rb sb y I w p n lt filename gt Transfer files to or from this device overa A dial out of band connection A 10 303562 A Rev 00 Appendix B TCL Support The BCC supports the following subset of Tool Command Language TCL scripting commands on the router platform append break case e catch close concat continue e eof e error eval e exit expr e flush for foreach gets global if incr interp join lappend lindex linsert list llength lrange e switch Ireplace unset
62. r is an attribute or property of a configurable object Parameters can be classified as one of the following e Required e Derived e Optional Required Parameters For any BCC object required parameters are a minimum set of parameters for which the BCC requires you to supply values For example the required parameters of a physical port are slot and connector Derived Parameters Derived parameters are parameters for which the BCC supplies a value For example a derived parameter of the global OSPF object is router id In this case the BCC derives a value for router id from the address of the first IP interface configured on the device Optional Parameters Optional parameters are parameters for which you can specify customized values replacing any default values set by the system For example an optional parameter of an Ethernet interface is bofl retries This parameter normally has a default value of 5 5 retries but you can change this to another numeric value 303562 A Rev 00 Chapter 2 Getting Started with the BCC This chapter provides information about the following topics Topic U 2 Q 1 Entering and Exiting the BCC Interface DD ER Displaying Context Navigating in Configuration Mode Displaying Configuration Data no do INO 1 de co Using Online Hel DD EM Entering and Exiting the BCC Interface To access the BCC interface on a
63. ree percentage does not necessarily indicate a buffer shortage it may be a transient condition The table includes the following information Slot Slot number Used Number of buffers used by each process Free Percentage of free buffers on each slot Total Total number of buffers available Free Total number of free buffers Displays link modules and drivers installed on all slots If the configuration displayed differs from that expected your configuration file may be incorrect wrong module type specified for example or there may be a problem loading the software 303562 A Rev 00 System show Commands information Displays general system information system name contact node location image data MIB version and total uptime since last cold boot memory Displays the global memory usage for all active slots in the system Memory usage is not as volatile as buffer usage so a low free percentage may indicate that you need more memory The table includes the following information Slot Slot number Total Total number of memory DRAM bytes available on each slot Used Number of memory bytes used on each slot Free Amount of free memory on each slot Free Percentage of free memory on each slot protocols Displays the protocols installed on all slots in the system If the configuration displayed differs from that expected your configuration file may be incorrect wrong protocol specified for example or there ma
64. rguments Enter only one of the choices Do not type the vertical line when entering the command Example If the command syntax is show ip alerts routes you enter either show ip alerts or show ip routes but not both 303562 A Rev 00 XV Using the Bay Command Console BCC Acronyms ARP ATM DCM DRAM IP IPX LAN MAC OSPF RIP SNMP SRM L TCP IP TFTP WAN Address Resolution Protocol asynchronous transfer mode data collection module dynamic random access memory Internet Protocol Internetwork Packet Exchange local area network media access control Open Shortest Path First Routing Information Protocol Simple Network Management Protocol system resource module link Transmission Control Protocol Internet Protocol Trivial File Transfer Protocol wide area network Bay Networks Technical Publications You can now print Bay Networks technical manuals and release notes free directly from the Internet Go to support baynetworks com library tpubs Find the Bay Networks product for which you need documentation Then locate the specific category and model or version for your hardware or software product Using Adobe Acrobat Reader you can open the manuals and release notes search for the sections you need and print them on most standard printers You can download Acrobat Reader free from the Adobe Systems Web site www adobe com xvi 303562 A Rev 00 Preface You can purchase Bay Network
65. ring Multiple Commands on a Line c icicissadsinneoadicicnncedacianaeadaccinnnedaabinnneoadicnne 3 4 Continuing a Command L s ssrssississias trrererrrrrer ry rererrrr rr Terr 3 4 SAN COMMENDS md a 3 5 Comigurston Command SYM K crsccsccsccnnncecaccsuscsesiagsareoaqcanonniaaaazartnaaaisanensaanuameteadnnnoness 3 5 Command Syntax RegquirememMe svkmmmnmmtennnmvjujittjhntiein 3 5 Using Basio Ful SOA siiin a 3 6 TET EE 3 7 Using Abbreviated S TE Lavaesnaneseeuermkgedunnronnituenvmsnharyaje 3 7 Specifying Parameter VAlles cca scicinccdarcninedaxacinnadendtndwsaendarivaedananinnndadsitinndaaaitntenaannanis 3 8 Required Derived and Other Paranal areas 3 8 Specifying Multiple Parameter Value Pairs mrnrnnnnnnonrrrnrrrnnrrnrrnnrnnnrrrnnrnnnrnnnn 3 8 Disabling Reenabling and Deleting a Configured Object a se 3 10 Creating and Using BOC Command Files cccsuczsasstenisvatessussteeidunnsteaaiauns auke 3 10 Saving Commands to a Fil Luenenasneeuineusinsiaeiteiredeoreinssnre unbe 3 11 Adding Comments to a Command FIG um emeiunemeunmrenaneeiinessnnneeivmi 3 11 Entering Configuration Commands from a File ccceeseeceeeeeseeceeeeeeeeeeeeeeeeeeeeees 3 12 Saving the Active Configuration as a Bootable Binary File mrrrrrrrrrrrrrrrrrrr0n00 O12 vi 303562 A Rev 00 Chapter 4 Tutorial Configuring a Network Device Creating and Modifying a Device Configuration cccccceceseeeeeeeeeeeeeeeeeeeeeeaaeeteneeees 4 1 Disabl
66. s documentation sets CDs and selected technical publications through the Bay Networks Collateral Catalog The catalog is located on the World Wide Web at support baynetworks com catalog html and is divided into sections arranged alphabetically e The CD ROMs section lists available CDs e The Guides Books section lists books on technical topics e The Technical Manuals section lists available printed documentation sets Make a note of the part numbers and prices of the items that you want to order Use the Marketing Collateral Catalog description link to place an order and to print the order form How to Get Help For product assistance support contracts or information about educational services go to the following URL http www baynetworks com corporate contacts Or telephone the Bay Networks Technical Solutions Center at 800 2LANWAN 303562 A Rev 00 xvii Chapter 1 Overview of the BCC The BCC is a command line interface for configuring Bay Networks devices After logging on to a device you access the BCC by entering the bec command at the Technician Interface prompt Figure 1 1 Technician Interface Access Login the BCC BCC0001B Figure 1 1 The Technician Interface and the BCC Interface 303562 A Rev 00 1 1 Using the Bay Command Console BCC From the bcc gt prompt you can e Execute any system command not classified as Technician Interfac
67. s expressly provided in this Agreement Licensee may not copy or transfer the Software or user manuals in whole or in part The Software and user manuals embody Bay Networks and its licensors confidential and proprietary intellectual property Licensee shall not sublicense assign or otherwise disclose to any third party the Software or any information about the operation design performance or implementation of the Software and user manuals that is confidential to Bay Networks and its licensors however Licensee may grant permission to its consultants subcontractors and agents to use the Software at Licensee s facility provided they have agreed to use the Software only in accordance with the terms of this license 3 Limited warranty Bay Networks warrants each item of Software as delivered by Bay Networks and properly installed and operated on Bay Networks hardware or other equipment it is originally licensed for to function substantially as described in its accompanying user manual during its warranty period which begins on the date Software is first shipped to Licensee If any item of Software fails to so function during its warranty period as the sole remedy Bay Networks will at its discretion provide a suitable fix patch or workaround for the problem that may be included in a future Software release Bay Networks further warrants to Licensee that the media on which the Software is provided will be free from defects in materials and
68. sed to boot the router or reset a slot The table shows the volume and file name used as the source of the configuration The table also shows the date and load time image Displays the router s software image for each slot including the integration that is the source of the image the date and time of the image s creation and the file name that contains the image 303562 A Rev 00 C 5 Using the Bay Command Console BCC memory lt slot gt Displays memory configuration and capacity information about all slots or a specific slot The table includes the following information Slot Slot number Local Memory Total memory capacity in megabytes of the processor on the slot Global Memory Current memory configuration in megabytes of the processor on the slot Total Memory Total local and global memory in megabytes proms Displays PROM information for all slots The table includes the revision and build date of the bootstrap PROM and the diagnostics PROM slots Displays hardware information about all slots in the system The table includes information about the processor module and link module for each slot as well as the module type revision and serial number The revision and serial numbers are in decimal format For the AN the table indicates that the AN has an 802 3 repeater HUB by indicating that the link module is an ANSEDSH For the ASN the table displays the revision and serial number of the chassis
69. ser manuals and all copies Bay Networks is not liable to Licensee for damages in any form solely by reason of the termination of this license 8 Export and Re export Licensee agrees not to export directly or indirectly the Software or related technical data or information without first obtaining any required export licenses or other governmental approvals Without limiting the foregoing Licensee on behalf of itself and its subsidiaries and affiliates agrees that it will not without first obtaining all export licenses and approvals required by the U S Government i export re export transfer or divert any such Software or technical data or any direct product thereof to any country to which such exports or re exports are restricted or embargoed under United States export control laws and regulations or to any national or resident of such restricted or embargoed countries or ii provide the Software or related technical data or information to any military end user or for any military end use including the design development or production of any chemical nuclear or biological weapons 9 General If any provision of this Agreement is held to be invalid or unenforceable by a court of competent jurisdiction the remainder of the provisions of this Agreement shall remain in full force and effect This Agreement will be governed by the laws of the state of California Should you have any questions concerning this Agreement contact Bay Net
70. ssigned value Where necessary enter the name of any parameter with a new value for example bofl disabled Enter info to check parameter values assigned to the new current object Enter for a list of objects and parameters configurable in this context of the configuration tree Enter or of the next object you want to configure for example ethernet Usage Help returned Reenter the command in the format shown in the usage Help message BCC0013B Figure 4 2 Typical BCC Configuration Cycle 4 4 303562 A Rev 00 Tutorial Configuring a Network Device To create the sample configuration shown in Figure 4 1 using BCC commands proceed as follows 1 Log on to the router as Manager so that you can modify the device configuration Bay Networks Inc and its Licensors Copyright 1992 1993 1994 1995 1996 1997 1998 All rights reserved Login Manager Mounting new volume Device label Directory 2 New Present Working Directory 2 Welcome to the Backbone Technician Interface Routerl gt 2 Start the BCC by entering bcc at the Technician Interface prompt Routerl gt bee Welcome to Bay Command Console To enter configuration mode type config To list all system commands type To exit the BCC type exit bec gt 3 Enter BCC configuration mode by entering config bcc gt config box 303562 A Rev 00 4 5 Using the Bay Command Console BCC 4 Check the hardware c
71. switch snmp board hssi mcel telnet console http mctl tftp ethernet ip ntp token ring Parameters in Current Context build date description location system name build version has mib counters type contact help file name on uptime System Commands You can add any of the following global services affecting all slots HTTP IP IPX FTP NTP SNMP Telnet and TFTP You can add any of the following interfaces ATM Ethernet FDDI HSSI serial token ring or virtual You can view the configuration of a board in any slot but you cannot modify the parameters of any board object 14 List the objects already configured at box level box lso board 11 board 5 board 9 ethernet 13 1 board 13 board 7 console 1 ip box When you added the first instance of IP to the box ip 192 168 133 114 255 255 255 224 the BCC automatically created the global IP object at box level 15 Add SNMP to the device box snmp snmp 4 10 303562 A Rev 00 Tutorial Configuring a Network Device 16 Check what you can configure next at this level snmp Sub Contexts community trap entity trap event Parameters in Current Context authentication traps lock timeout state has name type of service lock on lock address scope delimiter System Commands You can modify values currently assigned to parameters of SNMP and you can add a community define a trap entity or define a trap event 17 View the parameter defini
72. t of an object in terms of its location along a path that begins at the root level of the device configuration tree Each semicolon in the path marks a transition from one level to the next branch level in the device configuration tree The semicolon is also equivalent to a Return key entered at the end of a command effectively starting a new command line For example if you configure an IP interface address 1 2 3 4 mask 255 0 0 0 on ethernet 2 1 of a BLN router the BCC understands its location as box ethernet 2 1 ip 1 2 3 4 255 0 0 0 Figure 1 4 box ethernet 2 1 ethernet 2 1 ethernet 2 1 ip address 1 2 3 4 mask 255 0 0 0 ip 1 2 3 4 255 0 0 0 ip 1 2 3 4 255 0 0 0 BCC0017B Figure 1 4 Configuring IP and RIP on an Ethernet Interface Objects Classes and Instances In BCC terminology configurable entities are referred to as objects of a particular class each of which constitutes an instance e An object is a configurable physical or logical entity such as a physical interface or a protocol on an interface Every configurable object belongs to a specific class that defines its characteristics e Aclass is a template for a configurable object such as Ethernet or the protocol IP When you add a new object to the configuration of a device the BCC creates a copy an instance of the appropriate template 303562 A Rev 00 Overview of the BCC e An instance is an object uniquely identifiable within t
73. t the Next Level Displaying Values Assigned to Parameters To display the values currently assigned to all parameters of the current object enter the info command Example ip 1 2 3 4 255 0 0 0 info on ethernet 2 1 state enabled address 1 2 3 4 mask 255 0 0 0 assocaddr 0 0 0 0 cost 1 broadcast 1 2 3 6 configured mac address 0x mtu discovery off mask reply off all subnet broadcast off address resolution arp proxy off host cache aging cache off udp checksum on end station support off redirects on cache size 128 To display the value assigned to a specific parameter enter the parameter name as follows ip 1 2 3 4 255 0 0 0 proxy proxy off 303562 A Rev 00 2 15 Chapter 3 Entering Commands and Using Command Files This chapter provides information about the following topics Topic Page Entering Commands 3 1 System Commands 3 5 Configuration Command Syntax 3 5 Creating and Using BCC Command Files 3 10 Entering Commands This section contains information about e Using Command Abbreviations e Recalling Commands e Editing Command Lines e Entering Multiple Commands on a Line e Continuing a Command Line 303562 A Rev 00 3 1 Using the Bay Command Console BCC Using Command Abbreviations When you enter BCC commands in configuration mode you can shorten object and parameter names for example eth ethernet You must enter a su
74. th syntax only The list excludes commands available only in BCC mode The combination help lt command gt displays detailed Help on a specific command excluding any commands available only in BCC mode The combination help all displays detailed Help on all system commands excluding those available only in BCC mode history lt n gt Display the command history list or for W VY the Technician Interface only recall lt n gt option Technician Interface only command number lt n gt from the history list info List values currently assigned to all VY VY configurable parameters of this object BCC configuration mode only ip lt subcommand gt lt flags gt Display data from IP show a different v v view for each subcommand or flag you Technician Interface only enter ip6 lt subcommand gt lt flags gt Display data from IPv6 show a different v view for each subcommand or flag you Technician Interface only enter list lt instances gt lt obj_name gt List objects in the MIB VY VY Technician Interface only loadmap lt s ot_list gt all lt filepath gt Display the load address and size of VY each dynamically loadable application for example a protocol continued 303562 A Rev 00 System Commands Table A 1 System Commands continued Login Access Privileges Command Purpose Manager User log lt vol gt lt logfile gt d lt date gt t lt ti
75. the BCC It includes the following sections Topic Page Creating and Modifying a Device Configuration 4 1 Disabling a Configured Object 4 15 Enabling a Configured Object 4 16 Deleting a Configured Object 4 17 Creating and Modifying a Device Configuration You configure a Bay Networks device by defining a set of objects starting at the root level of the device s configuration hierarchy Each object has a set of parameters with values set either by you or by the device software Following is a typical BCC configuration sequence 1 2 3 Open a Technician Interface session and start the BCC interface Start BCC configuration mode Use BCC configuration commands to create new objects in the device configuration and modify default values for parameters of each object to meet the requirements of your network Enable any box wide protocols not enabled automatically by the BCC for example TFTP and Telnet Server Use the save command to save your configuration as a bootable binary file on the device Exit BCC configuration mode exit the BCC to the Technician Interface and log out of the device 303562 A Rev 00 4 1 Using the Bay Command Console BCC You may find it helpful to first diagram what you want to configure in terms of the BCC configuration tree or hierarchy for the device Refer to the following sample router configuration Sample Router Configuration The f
76. tions using the BCC help command snmp help snmp snmp Parameters state Indicates the administrative state of this object enabled or disabled authentication traps Sends trap for sets from false Mgr or Community lock Allows the locking mechanism to be disabled lock address Allows the lock address to be cleared lock timeout 18 Define the SNMP community public snmp community public community public 303562 A Rev 00 4 11 Using the Bay Command Console BCC 19 Check the values currently assigned to parameters of this SNMP community community public info on snmp label public access read only scope type 20 To allow network management applications such as Site Manager to modify the device configuration change the value of the access parameter to read write community public access read write community public 21 Define an SNMP manager for the router community public manager Usage manager address lt value gt r manager lt address gt Required parameter address was not specified for manager The BCC error message indicates what you left out and automatically provides usage Help on how to configure an SNMP manager 22 Try again to add the manager this time supplying a value for its required parameter address You must enter a value for a required parameter but you can omit the name of the parameter community public manager 0 0 0 0 manager public 0 0 0
77. to the Technician Interface prompt bec gt exit Routerl gt 40 Enter the logout command to close your console or Telnet session with the router Routerl gt logout a Configured Object In most cases the BCC automatically enables objects that you add to the device configuration However you can disable an object to manage or troubleshoot the device Here is a BN router example of how to disable an object rip on ip 1 2 3 4 255 0 0 0 1 Specify the configuration context for the object you want to disable box ethernet 2 1 ip 1 2 3 4 255 0 0 0 rip vip 1 2 3 4 2 Disable RIP rip 1 2 3 4 disable rip 1 2 3 4 3 Verify that you disabled RIP rip 1 2 3 4 state state disabled rip 1 2 3 4 303562 A Rev 00 4 15 Using the Bay Command Console BCC You can also disable an object from its parent context using the following syntax disable lt BCC_instance_identifier gt Example ip 1 2 3 4 255 0 0 0 disable rip 1 2 3 4 ip 1 2 3 4 255 0 0 0 Using this method you remain in the current context after disabling the branch object Enabling a Configured Object If you disable a configured object you can use the BCC enable command to reenable that object Here is a BN router example of how to enable an object rip previously disabled on ip 1 2 3 4 255 0 0 0 1 Specify the configuration context for RIP box ethernet 2 1 ip 1 2 3 4 255 0 0 0 rip rip 1 2 3 4 2 Reenable RIP rip
78. urrent level in the device configuration tree lt parameter gt List the current default and legal values for this parameter of the current object lt object gt lt parameter gt List the current default and legal values for the specified parameter of this object lt n gt Repeat the last command or repeat the v Technician Interface only last command lt n gt times back lt n gt Move your current working location back f v lt n gt levels closer to the root level of the BCC configuration mode only BCC configuration tree bcc Start the BCC from the Technician v v Interface prompt boot lt vol gt lt image_name gt Reboot the system v lt vol gt lt config name gt cd lt vol gt lt directory gt Set or display the current working volume v and directory clear lt subcommands gt lt flags gt Clear specific device information such v as IP and RIP data clearlog lt s ot_ D gt Clear all previous events from the system event log commit Commit make effective new values that you assign to MIB attributes continued A 2 303562 A Rev 00 System Commands Table A 1 System Commands continued Login Access Privileges Command Purpose Manager User compact lt volume gt Compact existing files into a contiguous AY address space on a volume and compact all unused space into a single contiguous block of free space for new files
79. vigate from one object to another in BCC configuration mode by using e The back command e Configuration commands Navigating with the back Command In BCC configuration mode use the back command to move a specific number of levels back toward root level The syntax for the back command is as follows back lt n gt Entering the back command with no argument moves you back one level closer to root level Example rip 192 168 125 34 back ip 192 168 125 34 255 255 255 224 back ethernet 2 1t 303562 A Rev 00 2 3 Using the Bay Command Console BCC Entering the back command with an integer moves you from your current working location back toward root the number of levels you specify Example rip 192 168 125 34 back 2 ethernet 2 1 In this example the back 2 command moves you from the current working location rip 192 168 125 34 back two levels to ethernet 2 1 with ip 192 168 125 34 255 255 255 224 as the intervening level Note If you enter an integer value that exceeds the actual number of levels back to root box or stack level the BCC returns to root level Navigating with Configuration Commands Using BCC configuration commands you can e Move back to a previous level e Move back to root level e Move forward to the next level e Move from your current level to any other level in the device configuration tree Moving Back One or More Levels To move from your current working
80. workmanship under normal use for a period of 90 days from the date Software is first shipped to Licensee Bay Networks will replace defective media at no charge if it is returned to Bay Networks during the warranty period along with proof of the date of shipment This warranty does not apply if the media has been damaged as a result of accident misuse or abuse The Licensee assumes all responsibility for selection of the Software to achieve Licensee s intended results and for the installation use and results obtained from the Software Bay Networks does not warrant a that the functions contained in the software will meet the Licensee s requirements b that the Software will operate in the hardware or software combinations that the Licensee may select c that the operation of the Software will be uninterrupted or error free or d that all defects in the operation of the Software will be corrected Bay Networks is not obligated to remedy any Software defect that cannot be reproduced with the latest Software release These warranties do not apply to the Software if it has been 1 altered except by Bay Networks or in accordance with its instructions 11 used in conjunction with another vendor s product resulting in the defect or iii damaged by improper environment abuse misuse accident or negligence THE FOREGOING WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT L
81. works Inc 4401 Great America Parkway P O Box 58185 Santa Clara California 95054 8185 LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS AGREEMENT UNDERSTANDS IT AND AGREES TO BE BOUND BY ITS TERMS AND CONDITIONS LICENSEE FURTHER AGREES THAT THIS AGREEMENT IS THE ENTIRE AND EXCLUSIVE AGREEMENT BETWEEN BAY NETWORKS AND LICENSEE WHICH SUPERSEDES ALL PRIOR ORAL AND WRITTEN AGREEMENTS AND COMMUNICATIONS BETWEEN THE PARTIES PERTAINING TO THE SUBJECT MATTER OF THIS AGREEMENT NO DIFFERENT OR ADDITIONAL TERMS WILL BE ENFORCEABLE AGAINST BAY NETWORKS UNLESS BAY NETWORKS GIVES ITS EXPRESS WRITTEN CONSENT INCLUDING AN EXPRESS WAIVER OF THE TERMS OF THIS AGREEMENT iv 303562 A Rev 00 Contents Preface Before EE REE aA atdala Sareea TEE ASAS xiii Tet CTC INE iie iaaa aa a ehan aa a xiv FE EE REE T xvi Bay Networks Technical Publications summeres ijeveuoienbiieeen no AN How OLE xvii Chapter 1 Overview of the BCC EE REE EEE 1 2 Nb SE SR 1 2 Terminology and EIS AS sunia 19 Conngoraton Hera sereias oara 1 3 1 EEE EEE 1 5 Objects Classes and Instances ccccrsosacsenvsecddtennesdanciexeseiaeierevedadouenseiaidinenesdicucens TB BOG INatnce GENT seni 1 7 Global B Wide OPEN scine a a ea aii 1 7 Physical Device OBJECTS sccstccssarcuscnrsseeatsnedsoenisnicaarenskneatarnimcaeiannudonterensentenarmdlines 1 8 PPE ES aaran inae NEE E ATN E 1 10 KE Ne ee RE ENE 1 10 Denved PANTS sa saseodmtn dradd a aA ends 1 10 Ophonal Parameters saorane a
82. y be a problem loading the software 303562 A Rev 00 C 11 Using the Bay Command Console BCC tasks Displays the number of tasks scheduled to run on all slots This number is highly volatile and a large In Queue value does not necessarily indicate a problem The table includes the following information Slot Slot number Total Total number of tasks running on each slot In_Queue Number of tasks scheduled to run in Queue Percentage of tasks scheduled to run C 12 303562 A Rev 00 Table D 1 Appendix D Syntax for Module Location Table D 1 lists the syntax for specifying the physical location of a module for each Bay Networks device that the BCC supports Syntax for Specifying Module Location per Device Platform Syntax AN ANH lt interface gt lt slot gt lt connector gt e lt interface gt Interface type ethernet token ring serial etc e lt slot gt 1 AN ANH is a one slot device e lt connector gt numbering starts with connector 1 Example ethernet slot 1 connector 3 This is an Ethernet interface configured on AN ANH connector 3 which exists on an Ethernet adapter module Connectors 1 and 2 are on the base module ASN lt interface gt lt slot gt lt module gt lt connector gt lt interface gt Interface type ethernet token ring serial etc e lt slot_number gt 1 2 3 or 4 depending on the setting of the module ID switch on each ASN
83. y the University of California Berkeley The name of the University may not be used to endorse or promote products derived from such portions of the software without specific prior written permission SUCH PORTIONS OF THE SOFTWARE ARE PROVIDED AS IS AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE In addition the program and information contained herein are licensed only pursuant to a license agreement that contains restrictions on use and disclosure that may incorporate by reference certain limitations and notices imposed by third parties ii 303562 A Rev 00 Bay Networks Inc Software License Agreement NOTICE Please carefully read this license agreement before copying or using the accompanying software or installing the hardware unit with pre enabled software each of which is referred to as Software in this Agreement BY COPYING OR USING THE SOFTWARE YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS UNDER WHICH BAY NETWORKS WILL PERMIT YOU TO USE THE SOFTWARE If you do not accept these terms and conditions return the product unused and in the original shipping container within 30 days of purchase to obtain a credit for the full purchase price 1 License Grant Bay Networks Inc Bay Networks grants the end user of the Softw

Avaya Bay Command Console BCC User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents