Audiovox SP-11CD User's Manual
Contents
1. A AUDIOVOX MODEL SP 11CDP 10 DISC CD CHANGER DIGITAL AUDIO INSTALLATION MANUAL PACKING LIST MAIN UNIT INSTALLATION PARTS Bracket Machine Screw M4x 10 d 4 pcs Stud Bracket 2 pcs Screw Hole Cover Labels OTHER ACCESSORIES CD Magazine P N SP11M Changer Hexagonal Bolt M6 x 15 A 4 pcs Index seal sheet SS QOQ 1 pc Installation Manual rg e 1 pc 5 Meter Din Cable d 1 pc Hexagonal Nut M6 4 pcs Owner s Manual 1 pc BEFORE INSTALLING THE UNIT Transport Lock Screws TRANSIT BOLTS 2 RIGHT SIDE 1 LEFT SIDE The mechanism in the CD changer is locked into place during shipment by the transport screws Be sure to remove the screws prior to installation e Caution After removing the transport lock screws place a piece of masking tape over each screw hole The tape will keep out dust which could cause the unit to malfunction Installation and Wiring Precautions 1 To prevent a short circuit e Be sure to turn off the ignition and remove the negative battery cable prior to installation e Connect power wires last Note Ifthe changer is to be installed in a car that is equipped with an on board drive or navigation computer do not disconnect the battery cable If the cable is disconnected the computer memory may be lost Under these conditions use extra caution during installation to prevent a sho2. ACKET Left Side MACHINE SCREWS w WASHERS M4x10 BRACKET Right Side Determine the mounting location and drill four mounting holes 4 Mount the unit in place using four self tapping screws M5 x 12 Never mount the unit near the fuel tank Use RTV silicone sealer on screw threads and around the holes to prevent moisture intrusion SELF TAPPING BRACKET SCREWS M5 x 12 Left Side __ f men i i i i ji i i i i i i i 1 i i 1 DRILL HOLES 4MM IN DIAMETER BRACKET Right Side PROCEDURE FOR 45 ANGLE INSTALLATION W O STUDS Note If the anti vibration spring position has been changed and verified for 45 angle mounting as shown on page 4 start with step 2 Determine the mounting location and drill four mounting holes Set the 2 anti vibration springs to position 45 Attach bracket to each side of the unit using the machine screws with flat and lock washers M4x 10 In the 45 position use holes 1 and 3 as shown at left NOTE Use masking tape to cover unused mounting holes on sides of unit Left Side BRACKET Right Side MACHINE SCREW WITH FLAT AND LOCK WASHERS M4 x 10 Mount the unit in place using four self tapping screws M5 x 12 Use RTV silicone sealer on screw threads and around Never mount the unit near the fuel tank the holes to prevent moisture intrusion SELF TAPPING SCREWS Pi M5 x 12 BRACKET Left Side BR
3. ACKET DRILL HOLES 4MM IN DIAMETER Right Side PROCEDURE FOR CHANGER INSTALLATION USING MOUNTING STUDS Note Make sure the anti vibration spring position has been changed and verified for the proper angle mounting as shown on page 4 1 Determine mounting location If unit is to be installed onto mounting studs located under carpet lift carpet to expose metal chassis and mark position of each stud as shown below in detail A and B 2 Insert two hexagonal mounting bolts through underside of each bracket detail A and mount stud bracket in position using two self tapping screws into metal chassis Hex bolt heads should be flush with underside of stud bracket 3 Replace carpet over bracket studs detail B mark position of stud end of each bolt and cut holes in carpet so bolts protrude through carpet 4 Proceed with unit mounting by positioning unit mounting brackets over protruding hex bolts as shown in details C D and E Secure mounting brackets to bolts using hex lock nuts 5 if mounting studs are to be located directly on mounting surface with no carpet in between mount changer directly on studs as illustrated below in details A C D and E STUD BRACKET MOUNTING ARRANGEMENT Detail A STUD BRACKET MOUNTING UNDER A CARPET Detail B SELF TAPPING SCREWS M5 x 12 CARPET STUD BRACKET ie BOLT M6 x 15 STUD BRACKET CHASSIS NERTICAL INSTALLATION SUSPENDED INSTALLATION HORIZONTAL INSTALLATION Pt STUD B
4. RACKET WITH STUD BRACKET WITH STUD BRACKET Detail C Detail D Detail E STUD BRACKET CHANGER MOUNTING _4 BRACKET STUD BRACKET CHANGER MOUNTING J HEX NUT M6 BRACKET CHANGER MOUNTING r BRACKET VEHICLE WIRING Mating 8 pin DIN socket on rear of compatible radio chassis see note 1 below Car Stereo with CD Changer Controls CD changer NOTE 1 Check with your Audiovox car audio dealer to be sure your stereo is directly compatible with this CD changer 2 Wiring instructions for use with FM Modulator Commander Systems are included with the CDC MC1 CDC MCR2 P MC3 and P MCR4 accessories Printed in China 128 5779A 2000 AUDIOVOX CORP HAUPPAUGE NY
5. ion 0 position 90 position 45 4 o e VERTICAL 5 oa t ANTI VIBRATION SPRINGS POSITION PROCEDURE FOR HORIZONTAL INSTALLATION W O STUDS FU Attach a bracket to each side of the unit using the machine screws with integral flat and lock washers M4 x 10 In the horizontal position use bracket mounting holes 1 and 1 as shown at the right Set anti vibration springs to position O as shown above NOTE Use masking tape to cover un used mounting holes on sides of unit MACHINE SCREW WITH FLAT AND LOCK WASHERS MA x 10 2 Determine unit mounting location and drill four mounting holes Never mount the unit near the fuel tank DRILL HOLES 4MM IN DIAMETER I Secure the unit in place using four self tapping screws SELF TAPPING SCREWS M5 x 12 BRACKET eet TIX M5 x 12 Use RTV silicone sealer on screw threads and around Left Side the holes to prevent moisture intrusion Right Side Note PROCEDURE FOR VERTICAL INSTALLATION W O STUDS If the anti vibration spring position has been changed and verified for vertical mounting as shown on page 4 start with step 2 1 Set the 2 anti vibration springs to position 90 Attach bracket to each side of the unit using machine screws with integral flat and lock washers M4 x 10 In the vertical position use holes 2 and 2 as shown at left NOTE Use masking tape to cover unused mounting holes on sides of unit BR
6. rt circuit 2 Do not install the unit in the following locations e Locations exposed to direct sunlight Where hot air is discharged from the car heater e In areas subject to extreme temperatures 3 Incorrect installation can cause the sound to skip when playing a disc Mount the unit firmly in place using the supplied brackets and screws 4 Be careful not to damage the car wiring 5 e Be sure to use the supplied screws e Be careful not to snag any wires when tightening screws e Do not use any of the screws that are part of the brake or steering system to install the unit 6 e This unit cannot be installed on either side or up side down Installation in such positions will cause the mechanism to malfunction INSTALLATION The unit can be installed horizontally vertically or ata 45 angle The position of the built in anti vibration springs left and right side must correspond to the mounting position chosen If the springs are not set correctly for the type of installation chosen the anti vibration compensation will not be effective and vibration may cause the disc to skip CAUTION After setting the built in anti vibration springs place masking tape over the holes The tape will keep out dust which could cause the unit to malfunction HORIZONTAL INSTALLATION VERTICAL INSTALLAITON 45 ANGLE INSTALLATION Set the 2 anti vibration springs to Set the 2 anti vibration springs to Set the 2 anti vibration springs to posit
Download Pdf Manuals
Related Search