Audiovox Prestige Platinum 128-8128 User's Manual
Contents
1. 128 8128 2 of 24 known as code grabber which will receive and store the signal from your keychain transmitter and re transmit at a later time to disarm your system Your Keeloq Code Hopping transmitters will change their signal every time the button is pressed so when a thief grabs then re transmits your signal the alarm system will not respond If your transmitter button is pressed more than fifty times while it is out of range of the vehicle children playing with your keys the transmitter will not operate when you return to the vehicle and will need to be re aligned to the receiver To do this simply press button 1 lock two times within a one second time period The system will now respond to that transmitter each time a button is pressed NOTE This system is custom configurable and can be set up to operate with a number of options controlled from any transmitter button or button combination For reference we will describe operation assuming that your system is pro grammed for separate lock and unlock buttons Also reference will be made to the icons as shown on the buttons left NOTE The LCD based remote will be explained in detail fur ther in this manual See System Status described later in this manual Consult your installation center if your system has been configured differently NOTE Your system has the option of using a siren the vehicle horn or both for the sounding device Where the siren is referenc2. 128 8128 Page 24 128 8128 24 of 24
3. Model APS 997a Owner s Manual 4 Button Remote Start Security System With Plug In Shock Sensor amp Starter Disable IMPORTANT order to provide you with the highest level of security to your vehicle this system is aquipped with selectable manual override circuitry It is posse that you will need to override you security system if the transmitter ecomes lost or inoperative due to battery failure Reading the sections on Manually Overriding Your System is necessary to fully understand the procedure required to enable your vehicle in such situations addition the chart on the last page of this manual has a section for the particular features and options installed in your vehicle as well as the override method selected Although the default mode is Valet Switch operation the system can be configured for Custom Code operation for enhanced security Confirm the override mode selected on the last page of this manual and familiarize yourself with the section on it s opera tion FEATURES 1 Two Way 5 Button Remote Control And 1 One Way 5 Button Remote Control Six Channel Code Learning Programmable Receiver External Superheterodyne Transceiver Antenna Single Or Two User Programmable W Separate Control Outputs Single Button Lock Unlock or Separate Button Lock Unlock or Both pee Keyless Entry With Optional Access Guard must have power door ocks Selectable Manual Override Mode New Enhanced Panic Featur
4. Parking Light Flasher Relay On Board Plug In Dual Stage Shock Sensor Pre detect Full Trigger and City Mode Audible Arm Disarm Defect and Tamper Chirp Indications Headlight Control Output Illuminated Entry Control Output Active or Passive Arming Selectable Programmable Auto Lock On Off Programmable Auto Unlock On Off Drivers Door All Doors Programmable Door Lock Pulse Duration 1 Second 3 5 Seconds 1 Sec L Dbl U L Programmable Active or Passive Door Locks User Programmable Permanent Chirp Delete On Command RF Chirp Delete from Transmitter Or Selectable Through Software Dome Delay Learn Circuitry Patent Pending OPTIONS Remote Trunk Release must have electric trunk release Remote Keyless Entry must have power door locks Multiple Vehicle Capable Remote Power Window Roll Up Remote Garage Door Interface CAUTION Be certain that the vehicle is outdoors before using this or any remote vehicle starting device A running engine produces dangerous car bon monoxide fumes which can be harmful or fatal if prolonged expo sure occurs DO NOT remote start the vehicle if it is garaged YOUR CODE HOPPING TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current auto motive security system Some of today s sophisticated auto thieves use a device Page 2
5. Press the Arm Lock button to Lock and Arm the System The Lock Icon is displayed on the LCD panel amp the parking lights flash once When Armed Press the Disarm Unlock button to Unlock and Disarm the System The Unlock Icon is displayed on the LCD panel amp the parking lights flash twice When the Key Icon Button Has Been Operated for 3 seconds the trunk open icon will flash on the LED Screen If text mode was selected the words Trunk Open will appear and remain on the screen until the trunk is shut Trunk ipa Trunk Tagged Page 14 128 8128 14 of 24 When the Key Icon Button is pressed 2 times in succession three puffs of smoke are displayed on the LCD screen while the vehicle is running The exhaust indication will flash and the hour glass will indicate count down timer based on the 5 10 15 or 20 minute run time set up by your installation center When the unit shuts off the exhaust indication will turn off and the transmit ter will play a melody Note Engine can be started in many modes armed disarmed valet etc The screen shown is Locked Armed and running When the Panic Mode has been activated and the 1 820 80 system is armed the vehicle s lights will flash the A siren and lock icon will be displayed on the LCD m screen and the siren will beep If the system is Foote seman disarmed and the Panic Mode is activated the lights will flash unlock icon will be
6. will continue for 48 hours NOTE The automatic start up timer can also be initiated from the keychain transmitter To do this 1 Start the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button 2 times 2 Shut off the vehicle using the ean transmitter by pressing and releasing the second channel transmitter button 2 times Page 11 128 8128 11 of 24 3 Within 10 seconds of step 2 activate the RF start command two times Push the second channel button of your keychain transmitter 4 times The parking lights will flash and the siren will chirp 4 times indicating the timed start mode 15 activated CANCELING THE AUTOMATIC START UP TIMER To cancel the automatic start up timer do one of the following 1 Start the vehicle manually with the use of the ignition key and depress the brake pedal 2 Remote start the vehicle using your keychain RF transmitter NOTE Option button used in combination is only available on the alternate re mote transmitter and not available on the LCD Transmitter OPTIONAL DEVICE OUTPUT CHANNEL 3 Controlled Trunk Key Button Other Transmitter button configurations are also available Con sult your installation center for other configurations not listed above that may have been programmed to operate a specific feature of your system This Seely system is equipped with an output which will activate when the appropriate transmitte
7. 2 CHIRPS 3 CHIRPS 4 CHIRPS ARM DISARM ARM DOOR OPENED DISARM INTRUSION These chirps are optional and can be de activated PARKING LAMP INDICATORS 1 FLASH 2 FLASHES 3 FLASHES ARM DISARM DISARM INTRUSION Remote Start Function Door Lock Time Parking Lights Run Time Remote Activation Chirp Remote Alarm Function Channel 1 Channel 2 Auto Door Lock Auto Door Unlock Passive Lock Passive Arm Siren Horn Horn Chirp Valet Coded Ovrride Chirp On The Fly Remote Trunk Release And Remote Start Remote Window Close Additional Option FEATURE AND FUNCTION SETTINGS To Be Completed By Installing Technician Settings 5 Sec teady 10 Min ff 1 Sec Pulse 5Min On Een Not Used rivers n On iren amp Horn 10mS Coded On Channel 3 Additional Option Additional Option Remote Garage Interface 1 Sec L Dbl UL 15 Min Arm Only Disarm Disarm 2 off Horn Only 30mS Channel 4 Channel Transmitter Buti 1 2 1 128 8128 23 of 24 2007 Audiovox Electronics Corp 150 Marcus Blvd Hauppauge 11788
8. parking hand brake 3 Be certain your foot is off the brake pedal 4 Press the program Push Button switch 2 times within 5 seconds The paring lights will flash two times indicating the mode was successfully entered If your parking lights flashed four times this indicates the turoo mode was on and is now turned off With the turbo timer mode selected on after you ve arrived at your destination while the engine is still running set the parking brake pause 2 seconds then turn the ignition switch to the off position The engine will continue to run the allotted time according to the selection during installation If you do not want the vehicle to continue to run for one cycle simply step on the vehicle s brake or release the parking brake or activate the transmitter s start button two times in succession Any of these will cause the engine to turn off TELEMATIC UPGRADE This system has the ability to have a telematic upgrade module connected to it This is a upgrade that can give you control of certain functions of your vehicle from a Telephone or in some cases a computer interface Please check with your installation center for most recent Telematic Upgrades If you had a Telematic Upgrade installed the manual supplied with the upgrade unit will provide a p erators manual advising of the features of the system and means available to control these features of your vehicle TRANSCEIVER ICONS AND THEIR INDICATIONS When Disarmed
9. to run but now on it s own power NOTE The engine will stop running before the expiration of the pre programmed run timer if you complete any of the following 1 Press and release the programmed channel of your keychain transmitter two times within 2 seconds 2 Depress the brake pedal 3 Open the hood 4 Move the red handled control switch to the off position 5 Race the engine to above 4000 RPM OPERATING ON AUTOMATIC START UP TIMER MODE Your system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine WARNING Be certain that the vehicle is outdoors before using this or any re mote vehicle starting device A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs DO NOT remote start the vehicle if it is garaged TO BEGIN THE AUTOMATIC START UP TIMER 1 Turn the ignition key on then off 2 Within 10 seconds activate the RF start command two times ee the programmed channel button of your keychain transmitter 4 times The parking lights will flash and the siren will chirp 4 times indicating the timed start mode 15 activated The vehicle on a 2 or 4 hour interval basis will automatically start run_for the pre programmed time 5 10 15 or 20 minutes and then shut off This
10. 0 Caution Be certain vehicle is outside before activating this mode To toggle this feature on of off from the Locked Armed mode press the Option and Lock buttons simultaneously Available on certain remote start models only Throughout this manual you will find screen shots where they apply if using the two way transmitter If using the one way transmitter while the two way transmit ter is within range of the vehicle the two way transmitter will update it s screen Page 19 128 8128 19 of 24 THIS PAGE LEFT BLANK INTENTIONALLY Page 20 128 8128 20 of 24 TRANSMITTER FUNCTION SELECTION BUTTON ICON TONE VIBRATE TIMING ADJUST MODE HRS PRESS FOR 5 SECONDS 18 88 2 BEEP TONES TIMING ADJUST MODE MINS 1X mu 1 8 88 ALARM CLOCK ADJUST MODE HRS 2X ou 1 8 88 ALARM CLOCK ADJUST MODE MINS 3X 18 88 ALARM CLOCK amp POWER UP MUSIC SELECT 4X 8 5 SELECTIONS PRESS KEY BUTTON OR OPTION BUTTON TO SELECT ALARM CLOCK ADJUST MODE ON OFF 5X ON OFF TIMING COUNT DOWN ADJUST MODE HRS 6X 18 88 TIMING COUNT DOWN ADJUST MODE MINS 7X 18 88 TIMING COUNT DOWN END MELODY SELECTION 8 8 5 SELECTIONS PRESS KEY BUTTON OR OPTION BUTTON TO SELECT TIMING COUNT DOWN MODE SELECT ON OFF 9X ON OFF REMOTE START ON MELODY SELECT 2 RANSMITTER FUNCTION OPERATION 000000
11. 000100 BUTTON 5 8 ICON 5 SELECTIONS PRESS KEY BUTTON OR OPTION BUTTON TO SELECT TONE VIBRATE 10 MIN PARKING COUNT DOWN TIMER Option 0 10 MELODY 20 MIN PARKING COUNT DOWN TIMER Option 0 20 MELODY 30 MIN PARKING COUNT DOWN TIMER Option 3X 0 30 MELODY 60 MIN PARKING COUNT DOWN TIMER Option 4X 1 00 MELODY 90 MIN PARKING COUNT DOWN TIMER Option 5X 1 30 MELODY 120 MIN PARKING COUNT DOWN TIMER Option 6X 2 00 MELODY PARKING COUNT DOWN TIMER OFF MODE Option 7X 0 00 MELODY BACKLIGHT DISPLAY FOR 10 SECONDS 1X ILLUMINATES DISPLAY VIBRATE TONE SELECT 6 1X 308 VIBRATE 4 TIMES OR BEEP 1 X ALARM CLOCK MODE SELECT ON OFF O 1X 18 88 MELODY FAHRENHEIT CELSIUS SELECT POWER SAVE MODE 0 1X 1X Forc MELODY MELODY Page 21 128 8128 21 of 24 THIS PAGE LEFT BLANK INTENTIONALLY Page 22 128 8128 22 of 24 5 997 SYSTEM FUNCTIONS GLANCE DASH LED INDICATORS RAPID FLASHING REARMING SLOW FLASHING OFF ON SOLID 3 FLASH PAUSE 2 FLASH PAUSE 1 FLASH PAUSE PASSIVE ARMING ACTIVE ARMED DISARMED VALET MODE INTRUSION ZONE 3 INTRUSION ZONE 2 INTRUSION ZONE 1 SIREN CHIRP INDICATORS 1 CHIRP
12. The vehicle s alarm will display the temperature Temperature is read from the alarm s module located below the dashboard This reading may be higher than actual ambient temperature due to the greenhouse and is relative only to the inside vehicle temperature Temperature Start Mode Available on certain models To toggle this feature or off from the armed mode press the Option amp 3 Unlock Buttons simultaneously the temperature icon appear on or disappear from the display and the transmitter will emit a tone NOTE This feature must be active in the feature selection menu of your system Check with your installing dealer to insure this feature is set to the on position Light The Display l She aan Press and release the F Function button one time The display will illumi nate for 10 seconds Vibrate Or Tones eee the F and unlock buttons simultaneously to toggle this feature on and off AA Daily Start Timer Only available on certain remote start units 24 24 Hour Start Timer Standing at the vehicle at the time you want it to start press the option lock buttons simultaneously for 1 seconds The transmitter will beep and display the 24 hr timer This is the time the vehicle will start when you follow the exit procedure In other words if you want the vehicle to start 6AM at 6AM of any morning standing at the vehicle press and hold the option lock buttons until you hear a beep and the 24 hr timer is display
13. displayed and the siren will beep on the LCD screen When ever the vehicle is operated from the two way transmitter the unit will beep responsive to the function executed at the vehicle 1 beep when armed 2 beeps when disarmed etc at times It may be inconvenient or too noisy to hear the beep tones so the system allows you to set the unit for vibrate mode To toggle on or off beep tones vibrate Simultaneously press the F and unlock buttons The icons shown left will appear in the upper left hand corner of the screen to indicate vibrate If the alarm system has been triggered the icon displayed on the transmitter LCD will indicate which zone has been activated as well sound the beep tones or vibrate dependent upon the setting as shown above The following trigger patterns will be displayed 8 00 Triggered and the entry attempt was made to of the vehicle Doors coy Triggered and entry attempt was made to the vehicles Hood or Page 15 128 8128 15 of 24 Triggered and entry attempt was made to the vehicles glass the vehicle has been hit or bumped hard enough to cause a response from the vibration detector ADDITIONAL ICONS THAT MAY BE DISPLAYED ARE If the arm disarm chirp tones have been turned off at the ve hicle when you arm or disarm the display will indicate this as shown and there will be no arm disa
14. e Any button other than unlock stops siren no change to the units state Smart Disarm If triggered elect to shut off siren or disarm entire unit pause Shock Sensor Via The Transmitter Pre Detect Off Pre amp Full Detect Off City Mode Output Controlled From Channel 3 Option Channel 3 For Trunk Or or 24 Hour Time Start Mode Cold Temperature Start Mode 2 or 4 Hour Automatic Start Mode Parking Meter Count Down Timer On LCD Remote Additional Count Down Timer Mode Remote Panic In All Modes Press amp Hold Lock Unlock Button For 3 Seconds To Engage Improved Custom Code Override User Selectable and Programmable Page 1 Taken from 997 edit clarify 24 hr start text replace one way transmitter graphics with new style Transmitter 07SP 5 07 1 28 81 2 8 1 of 24 Protected Push Button Valet Override Switch 7 Function LED Arm Disarm Zone 1 Zone 2 Zone Valet Arming Intrusion Alert With Memory Instant Siren Activation Starter Disable Output Additional Engine Immobilizer Output Optional Relay Required True Last Door Arming Hardwire Only Defective Zone By Pass Defective Zone Chirp Confirmation Unit Chirps To Report Zone Cleared 6 Tone Mini Siren Car Horn Output For Additional Alarm Response Improved Timing To Minimize RF Interference Additional Negative Trigger Input Hood and Trunk RF Inhibit With Ignition
15. e you arm_or disarm the system if the feature has been activated simply by holding the ARM or DISARM button for two seconds If you find the normal arming and disarming chirps annoying they can be turned off permanently eliminating the need to hold the ARM DISARM button for 2 seconds To do this Page 8 128 8128 8 of 24 1 Turn the ignition key on then off 2 Within 10 seconds press and release valet switch three times 3 If the chirps were on before you started then you will hear two chirps indicat ing they have been turned off If the chirps were off before you started then you will hear one chirp indicating they have been turned on NOTE Whenever the chirps are bypassed the 4 chirp intrusion indicator and 3 chirp defective zone indicator will always operate Since these are important warnings to you that something has happened they cannot be eliminated NOTE Your system must be programmed by the installation center to en able this feature REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations To use remote panic 1 Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds The alarm will immediately sound 2 To stop the alarm press and hold the Lock or Unlock button on the transmitter again for 3 seconds If the button is not pressed the alarm will automatically stop after 30
16. ected to a num oer of cieren optional accessories Some of the more common uses for this channel are Page 12 128 8128 12 of 24 Remote Car Starter Remote Window Closure Remote Garage Door Interface To remotely operate the device indicated momentarily press or press and hold the appropriate transmitter button s as indicated above ADDITIONAL REMOTE FUNCTION CHANNEL 6 Channel 6 is an alternate output that can be controlled by the unlock button of the transmitter or by and independent button or combination of buttons For your vehicle this output is Conirolled ae O Trunk Key Button O Option Button O Lock Unlock Buttons O Lock Trunk Key Buttons O Unlock Trunk Key Buttons Other Transmitter button configurations are also available Consult your installa tion center for other configurations not listed above that may have been programmed to operate a specific feature of your system This security system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are O Remote Car Starter O Remote Window Closure O Remote Garage Door Interface To remotely operate the device indicated momentarily press or press and hold the appropriate transmitter button s as indicated above ADDITIONAL REMOTE FUNCTION CHANNEL 7 Channel 7 is an alternate output that can be controlled by the unlock button of the transmitter or by and
17. ed This establishes a starting time The unit will start at the prescribed time once only This function must be selected each time you want the vehicle to start To activate this function a Turn the ignition switch off b Within 10 seconds of step a depress and hold the brake pedal while pressing the key icon transmitter button 2 times c the unit will emit 2 chirps the transmitter will beep and the start timer icon on the display will remain on The vehicle will start at the Page 17 128 8128 17 of 24 set time To toggle this feature off press the option lock buttons simulta neously until a is heard and the 24 hr timer turns off Note the unit will start once and run for the prescribed time If you require more Cee starting please refer to auto start up timer mode shown earlier in this uide OTE To insure accurate 24 Hour Start up it is advisable to reset the start time periodically as time may drift slightly each day alert tone may be needed to remind you of something important For instance you may a meeting 4 hours from now and you want a reminder in 3 Hrs and 45 Mins This additional count down timer allows you to set the count down up 19 Hours and 59 Minutes from the current time and when the timer reaches zero the transmitter will emit a tone or vibrate P penden on your preferred setting See chart for setting the count down time or this feature Timing Count Down 53 T
18. ed below the horn or both may in fact chirp or beep ARMING THE SYSTEM ACTIVE 1 Turn off the engine exit the vehicle and close all doors hood lid and trunk lid 2 Press and release Lock Arm button on the keychain transmitter The dash mounted LED begins to flash slowly Parking Lights flash one time Siren sounds one chirp If the siren horn sounds 3 chirps then you have left a door trunk or hood lid ajar Simply close the opened entry point to provide full protec tion If the siren chirped three times sometime after arming the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired Again closing the hood trunk or doors will correct the problem and you do not need to disarm the system to make the correction If the siren horn did not sound when arming then the chirps have been turned off and you should refer to the section titled ELIMINATING THE ARM DIS ARM CHIRPS in this manual Doors Lock Optional NOTE If the optional Headlamp illumination feature has been added and has been selected for operation when arming as an added convenience the system will turn on the headlights when the system is armed SILENT ARMING ACTIVE Must be activated during programming 1 Turn off the engine exit the vehicle and close all doors hood lid and trunk lid 2 Press and hold the Lock Arm button on the keychain transmitter for 2 sec
19. er control of the remote start the system can be programmed to allow you to shunt the shock sensor from the transmitter If the system has been such programmed simply press the lock button of your keychain transmitter anytime during the remote start cycle The shock sensor will be shunted for the entire run cycle and will resume normal operation after the remote start unit shuts off Check with your installation center to determine if this feature has been pro grammed into your system SAFETY Red Handled CONTROL SWITCH The control switch allows you to temporarily disable the remote starting function of your system To disable the unit move the red handled control switch to the off position The control switch also allows you to select between 2 hour start up and 4 hour start up when using the automatic start up timer mode The factory preset start up time for this mode 15 every 4 hours To select between 2 or 4 hour start up timer 1 Begin with the control switch in the on position 2 Turn the ignition switch on then off 3 Within 10 seconds move the control switch off on off on 2 switch cycles to select 2 hour start timer After 10 seconds expire the parking lights will flash and the siren will chirp 2 times confirming that the two hour start cycle is set Or within 10 seconds move the control switch off on off on off on off on 4 switch cycles to select a 4 hour start timer The parking lights will flash and the siren w
20. h zone was triggered Siren will not sound If the siren sounds 4 chirps then the alarm was triggered in your absence Before turning the key on examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered O Doors Unlock Optional 2 Step Doors Unlock Optional NOTE If the optional Headlamp illumination feature has been added and has been selected for operation when disarming as an added convenience the system will turn on the headlights when the system is disarmed WHILE THE SYSTEM IS SOUNDING If during a triggered state you wish to shut off the siren without disarming your security system simply press and release any transmitter button other than the Unlock Disarm button _ This action will turn off the siren yet leave the vehicle fully armed and protected This feature is particularly useful if you are aware of children playing near your vehicle that may accidently trigger your security system In this case you can cancel the siren sounding without disarming your alarm INTRUSION WARNING SIGNALS This system will inform you if an intrusion attempt has occurred while you were away trom the vehicle If an intrusion attempt has occurred the siren will chirp 4 times and the parking lights will flash 3 times when disarming the system Enter the vehicle and observe the red dash mounted LED to identify which zone was triggered If the LED is flashing one time pause o
21. he unit offers an additional count down timer for situations where Valet When the System is in the valet mode the icon shown will show in the display when the status check buttons are activated Parking Meter Counter The transmitter has a built in clock that can count down from 10 20 30 60 90 or 120 minutes This feature is useful when parking the vehicle in a metered parking lot If the time on the parking meter is 30 minutes you can set the count down timer to 20 minutes The transmitter will emit beep tone when the timer expires to remind you to get back to your vehicle See following chart for setting the parking meter count down timer feature Alarm Clock Mode nu The transmitter has a built in alarm clock that can be set to beep at a certain time each day The alarm clock mode must be set and the feature turned on To use this feature please refer to the chart on the following page NOTE Your system is shipped with two transmitters 1 two way shown on the left and the one way transmitter shown right The one and two way transmitters are programmed from the factory with separate lock amp unlock buttons the trunk key icon button operates remote start and remote trunk release where applicable The option button and any button combination may be programmed to operate various options Consult your installation center for button programming and options that may have been added to your vehicle Alt
22. hough this is the default programming from the factory this can be changed for you to any configura tion you prefer Please refer to the transmitter pro gram guides included with your kit OTE A maximum of two of either style transmitter may be programmed to your unit Battery Indicator Your transmitter has a battery indicator that is shown in the upper right Page 18 128 8128 18 of 24 corner of the screen as shown left This icon indicates a new battery shown with 3 bars As the battery deteriorates the bars will disappear 1 bar indicates the battery should be replaced Replace battery with a fresh 1 5V AAA battery and dispose of the used battery properly Other icons that will be displayed at times when certain functions and features are active in the vehicle or on the remote Range Indicator The range indicator will have bars to the side of the icon if the unit is out of range CI Vibrate Mode On this icon will be displayed if you select vibrate instead of tones To toggle vibrate and off press F Unlock simultaneously Alarm Clock This icon will be toggled off when the F Trunk Key buttons are pressed simultaneously The feature must be set in the feature selection menu of the transmitter Timing Count Down The unit offers an additional count down timer for situations where_an alert tone may be needed to remind you of something important Setting information shown on prev
23. ill chirp 4 times confirming that the 4 hour start timer is set REMOTE STARTING THE VEHICLE The system WILL NOT start the vehicle if any one of the following conditions exists 1 The Vehicle Hood Is Opened 2 The Gear Selector Is In Any Gear Other Then Park 3 The Brake Is Depressed 4 The Safety Control Switch Is In The Off Position Page 10 128 8128 10 of 24 WARNING certain that the vehicle is outdoors before using this or any remote vehicle starting device A running engine produces dangerous carbon monoxide fumes which can be harmiul or fatal if prolonged exposure occurs DO NOT remote start the vehicle if it is garaged To Remote Start The Vehicle Press and release the programmed channel of your keychain transmitter two times within 2 seconds vehicle will start and remain running for the pre programmed 5 10 15 or 20 minutes As a visual indication the parking lights will pest or turn on depending on the programming set up by your installation center When you arrive at your vehicle disarm the alarm system by pressing and re leasing the arm disarm button of your keychain transmitter Enter the vehicle and turn the ignition key to the on position CAUTION Do not turn the key to the start position This will cause the starter motor to engage with the already running engine which could result in damage Step on the brake pedal to disengage the remote start unit The vehicle will continue
24. independent button or combination of buttons For your vehicle this output is Conirolled ae O Trunk Key Button O Option Button O Lock Unlock Buttons O Lock Trunk Key Buttons Unlock Trunk Key Buttons Other Transmitter button configurations are also available Consult your installa tion center for other Seen not listed above that may have been programmed to operate a specific feature of your system This security system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are O Remote Car Starter Remote Window Closure O Remote Garage Door Interface To remotely operate the device indicated momentarily press or press and hold the appropriate transmitter button s as indicated above TURBO TIMER MODE This system provides a means to cool down the vehicles turbo charger if so equipped by allowing the vehicle to continue to run for a prescribed period of time every time the vehicle s engine is turned off This feature requires the system to be set up for turbo timer during installation Consult with your installation center to be certain this feature was activated and how long the vehicle will continue to run 3 5 or 10 minutes after the ignition switch is turned off Page 13 128 8128 13 of 24 To activate the turbo timer Le the engine is running for more than 15 seconds 3 lace the gear selector in park 2 Set the
25. ious page Power Save Feature Press the F and Lock buttons simultaneously to toggle this feature on and off With this mode on the battery in the transmitter will go into a power down mode when the unit is disarmed 24 Hour Start Timer Standing at the vehicle at the time you want it to start press the option lock buttons simultaneously for 1 seconds The transmitter will beep and display the 24 hr timer This is the time the vehicle will start when you follow the exit procedure In other words if you want the vehicle to start 6AM at 6AM of any morning standing at the vehicle press and hold the option lock buttons until you hear a beep and the 24 hr timer is displayed This establishes a starting time The unit will start at the prescribed time once only This function must be selected each time you want the vehicle to start To activate this function a Turn the ignition switch off b Within 10 seconds of step a depress and hold the brake pedal while pressing the key icon transmitter button 2 times c the unit will emit 2 chirps the transmitter will beep and the start timer icon on the display will remain on The vehicle will start at the set time To toggle this feature off press the option lock buttons simultaneously until a beep is heard and the 24 hr timer turns off Temperature Start Mode This icon will appear when the temp start mode is activated The vehicle will start one time automatically when the temperature reaches
26. ne time pause etc then an intrusion attempt was made to the shock sensor or an accessory trigger ing device that may have been added to the system ff the LED is flashing two times pause two times pause etc then an intrusion attempt was made to a hood or trunk pin switch that was added to the system or to a light activated entry point if the alarm was installed using the voltage sensing feature ff the LED is flashing three times pause three times pause etc then an intrusion attempt was made through one of the vehicle s doors These intrusion warning indicators are stored in the system s memory and will only be erased when the ignition key is turned on VALET SWITCH NOTE Some units may include a combination Push Button LED Switch in these systems the LED and Switch are one and the same The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand your transmitter to parking attendants or garage mechanics When the system is in valet mode all alarm functions are bypassed however the remote panic feature and remote door locks will remain operational In addition the parking lights will flash to indicate locking and unlocking To use the valet mode the system must first be disarmed either by using your keychain transmit ter or by activating your personalized manual override code 1 Enter the vehicle and turn the ignition key to the on position 2 Press and hold the vale
27. nit will not recognize a 0 Zero or no digit entered in any place units or tenths NOTE If 15 seconds of inactivity expire or if the ignition switch is turned off for more then 5 seconds during any of the above steps the unit will revert back to the last successfully stored code Page 7 128 8128 7 of 24 Custom Code Programming Example To Change the code from the factory pre assigned code of 11 to 52 you would do the following 1 Disarm the system by use of the transmitter or by use of the emergency override sequence Turn the ignition switch to the on position Within 10 seconds press and release the valet override switch 3 times Within 10 seconds turn the ignition switch off on off on off on The siren or horn will beep and the lights will flash one time Within 10 seconds begin to press and release the pushbutton switch to set the tenths digit As per the example press and release 5 times to set the tenths digit to 5 Within 10 seconds of the last press of the pushbutton turn the ignition switch off then on Within 10 seconds begin to press and release the pushbutton switch to set the units digit As per the example press and release 2 times to set the units digit to 2 8 the ignition switch to the off position Immediately observe the LED flash pattern You will note the LED flashing five times pause and then flash two times pause This pattern will be re
28. on Consult your installation center for programming details The system comes from the factory with a pre programmed override code of 11 To change this default override code do the following 1 Disarm the system by use of the transmitter or by use of the emergency override sequence Turn the ignition switch to the on position 2 Within 10 seconds press and release the valet override switch 3 times 3 Within 10 seconds turn the ignition switch off on off on off on The siren or horn will beep and the lights will flash one time 4 Within 10 seconds begin to enter your chosen 10ths digit by pressing and releasing the pushbutton switch from 1 up to 9 times 5 10 seconds of the last entered 10ths digit turn the ignition switch off en on 6 Within 10 seconds begin to enter your chosen units digit by pressing and releasing the pushbutton switch from 1 up to 9 times 7 Finish by turning the ignition switch to the off position If the new code was accepted the unit will report back the newly entered code b flashing the LED first indicating the 10ths digit pause and then the units digit The unit will report the new code three times with a one second pause between each code then the system will begin arming If the LED flash pattern reports the previously stored_code the new code was not entered correctly Please repeat steps 1 through 7 above considering the following NOTE Acceptable digits 10ths or units are 1 through 9 The u
29. onds Page 3 128 8128 3 of 24 dash mounted LED begins to flash slowly Parking Lights flash one time Siren will not sound If the siren chirped three times sometime after arming the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired Closing the hood trunk or doors will correct the problem and you do not need to disarm the system to make the correction O Doors Lock Optional NOTE If the optional Headlamp illumination feature has been added and has been selected for operation when arming as an added convenience the sys tem will turn on the headlights when the system is armed The LCD Remote has the following response ARMING THE SYSTEM PASSIVE AUTOMATIC Must be activated during programming 1 the engine exit the vehicle and close and lock doors hood lid and runk lid The dash mounted LED begins to flash rapidly indicating 30 second passive arming has begun 2 Opening any protected entry point during the 30 second passive arming cycle will immediately suspend automatic arming and the 30 second passive arm ing cycle will restart when all doors are closed At the end of the passive arming cycle The dash mounted LED begins to flash slowly Parking Lights flash one time Siren sounds one chirp If the siren did not sound when arming then the chirps have been tu
30. peated three times indicating the new code 52 has been accepted and stored in memory NOTE If after step 7 the LED flashes a code other than what was just entered this indicates that the code has not been changed You will have to repeat steps 1 through 7 above being certain to note the following Acceptable digits 10ths or units are 1 through 9 The unit will not recognize a 0 Zero or no digit entered in any place units or tenths NOTE If 15 seconds of inactivity expire or if the ignition switch is turned off for more then 5 seconds during any of the above steps the unit will revert back to the last successfully stored code MANUALLY OVERRIDING YOUR SYSTEM USING THE CUSTOM CODE OVERRIDE Assuming the override code programmed has not been changed and the default override code of 11 is in the system s memory 1 Enter the vehicle and turn the ignition switch to the on position NOTE The siren will sound 2 Within 5 seconds press and release the pushbutton switch 1 time 3 Within 5 seconds turn the ignition switch off then on 4 Within 5 seconds press and release the pushbutton switch 1 time 5 Turn the ignition switch off then on and start the vehicle NOTE If you have changed the programmed override code then substitute your new code tenths for step 2 above and units for step 5 above ELIMINATING THE NORMAL ARM DISARM CHIRPS As explained earlier in the manual you can eliminate the chirps selectively any tim
31. r button is depressed for 4 seconds Although this output is intended to activate the trunk release option any other optional devices may be connected to this channel Consult your installation center for more information about this output ADDITIONAL REMOTE FUNCTION CHANNEL 4 Conirolled O Trunk Key Button O Option Button Lock Unlock Buttons O Lock Trunk Key Buttons O Unlock Trunk Key Buttons Other Transmitter button configurations are also available Consult your installa tion center for other configurations not listed above that may have been pro grammed to operate a specific feature of your system This security system has an additional feature that can be connected to a num ber of different optional accessories Some of the more common uses for this channel are O Remote Car Starter Remote Window Closure O Remote Garage Door Interface To remotely operate the device indicated momentarily press or press and hold the appropriate transmitter button s as indicated above ADDITIONAL REMOTE FUNCTION CHANNEL 5 Controlled O Trunk Key Button O Option Button Lock Unlock Buttons O Lock Trunk Key Buttons O Unlock Trunk Key Buttons Other Transmitter button configurations are also available Consult your installa tion center for other configurations not listed above that may have been pro grammed to operate a specific feature of your system This security system has an additional feature that can be conn
32. ries of warning tones Any strong impact to the vehicle s glass will cause the alarm to trigger for the full 30 second alarm cycle NOTE If the optional interior illumination circuit was installed the interior light will flash as well for the full 30 second alarm cycle DISARMING THE SYSTEM NOTE If the optional 2 step door unlock circuit is installed when the unlock transmitter button is activated the drivers door only will unlock pressing the unlock button a second time will cause all doors to unlock NOTE If your transmitter has been configured with single button Lock Unlock to activate the all door unlock feature operate the Lock Unlock button a second time within 3 seconds of the first unlock command 1 As you approach the vehicle press and release the Unlock Disarm button on the keychain transmitter The dash mounted LED turns off The LED will start flashing rapidly indicating that the system is re arming automatically Open any door to suspend the automatic arming Parking Lights flash two times If the parking lights flashed three times then the alarm was triggered in your absence Before turning the key on examine the LED to identify which zone was triggered Siren sounds two chirps If the siren sounds 4 chirps then the alarm was triggered in your absence Before turning the key on examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was t
33. riggered If the siren did not sound when disarming then the chirps have been turned off and you should refer to the section titled ELIMINATING THE ARM DISARM CHIRPS in this manual O Doors Unlock Optional 2 Step Doors Unlock Optional NOTE If the optional Headlamp illumination feature has been added and has been selected for operation when disarming as an added convenience the system will turn on the headlights when the system is disarmed SILENT DISARMING Must be activated during programming Note If the optional 2 step door unlock circuit is installed when the unlock transmitter button is activated the drivers door only will unlock pressing the unlock button a second time will cause all doors to unlock NOTE If your transmitter has been configured with single button Lock Unlock as shown to activate the all door unlock feature operate the Lock Unlock button a second time within 3 seconds of the first unlock command 1 Press and hold button the Unlock Disarm button on the keychain transmitter for 2 seconds The dash mounted LED turns off The LED will start flashing rapidly indicating that the system is re arming automatically Open any door to suspend the automatic arming Page 5 128 8128 5 of 24 Parking Lights flash two times If the parking lights flashed three times then the alarm was triggered in your absence Before turning the key on examine the LED to identify whic
34. rm chirps at the transmit ter This is true if the transmitter is set for vibrate mode When the vehicle is armed and a door is opened or ajar the transmitter will chirp 3 times the lights will flash and the display will indicate a door trigger as shown on the previous page When the door is closed or the zone clears the transmitter will chirp 1 time and the display will clear When the vehicle is armed and the hood or trunk is opened or ajar the trans mitter will chirp 3 times the lights will flash and the display will indicate a hood or trunk trigger as shown on the previous page When the hood or trunk is closed or the zone clears the transmitter will chirp 1 time and the display will clear Page 16 128 8128 16 of 24 ADDITIONAL REMOTE FEATURES The two way remote control unit allows you to access status information from the vehicle check temperature light the display toggle the transmitter from beep tones to vibrate mode initiate daily start timer and temperature start Selection of these and other features are shown below NOTE Transmitter must be within operating range of the vehicle approximately 1000 ft Check Vehicle Status _ Press the lock key option buttons simultaneously for 1 The vehicle s alarm will display the systems current status Check Temperature Only available on certain remote start units Press the option key buttons simultaneously for 1 second
35. rned off and you should refer to the section titled ELIMINATING THE ARM DISARM CHIRPS in this manual O Doors Lock Optional Door locking during passive arming is a selectable feature The alarm can be programmed to allow the doors to lock only when arming using the keychain transmitter and they will not automatically lock during passive arming PROTECTION WHILE THE SYSTEMIS ARMED Opening any protected door hood or trunk lid will cause the alarm to imme diately sound The alarm will continue to sound for 30 seconds then stop and continue to monitor all protected entry points If the thief left a door opened the alarm will sound for six 30 second cycles remain armed and ignore that trig gered zone Whenever the system is armed the dash mounted LED indicator will slowly flash This serves as a visual deterrent to the potential thief The LED is a ver low current bulb and will not cause the vehicle s battery to drain even when left unattended for extended periods Whenever the system is triggered the vehicle s parking lights will flash for the full 30 second alarm cycle attracting visual attention to the vehicle Optional Whenever the system is armed the vehicle s starting circuit will be a If the thief should choose to ignore the siren the vehicle can not be started Page 4 128 8128 4 of 24 Any mild impact to the vehicle s glass will cause the alarm to sound a short se
36. seconds Also if i transmitter button other than the Lock or Unlock button_is pressed and released the Panic mode will be turned off immediately The normal function of this transmitter button will be suspended during the Panic sounding period 3 During the panic mode the Lock and Unlock buttons can be used to lock and unlock the doors if the option is stated However once the unlock disarm button is pressed the vehicle s starter inhibit device where installed will be disabled allowing the vehicle to start NOTE While the Panic mode pressing and releasing the Lock Un lock buttons will if the option is installed lock and unlock the doors respectively While in the panic mode anytime the Unlock button is pressed the panic feature will continue for the allotted 30 seconds however the security system will be disarmed allowing the vehicle to start RF SHOCK SENSOR MODE SELECTION The way in which your alarm system reacts to threatening vibrations created by attempts to enter the vehicle by breaking a window is adjustable by the transmitter immediately after arming There are 4 modes of operation that can be selected by the operator 1 Normal Operation default mode In this mode any strong vibrations will cause the siren to sound full oper for 30 seconds Any lesser vibration will cause the siren to emit about 6 short warn away chirps pre detect 2 Stage 1 Omit pre detect In this mode the warn away chirps created b
37. t pushbutton switch until the dash mounted Page 6 128 8128 6 of 24 LED turns on solid The system will remain the valet mode 3 To return to normal operation press and release the pushbutton switch any time the ignition is on NOTE Always remember to return the system to normal operation This will ensure that the vehicle remains protected at all times MANUALLY OVERRIDING YOUR SYSTEM USING THE VALET SWITCH MANUAL OVERRIDE Your Security System can be disarmed without the use of the keychain transmitter This is necessary since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails If your system has been selected for Valet Switch manual override as indicated on the last page of this manual to bypass the alarm system 1 Open the vehicle door The alarm will sound 2 Turn the ignition key to the on position 3 Within 5 seconds press and release the valet pushbutton switch The alarm system will stop sounding and enter the bypass mode You can now start and operate the vehicle normally Typically this override mode is used only if the transmitter has become inopera tive PROGRAMMING YOUR CUSTOM OVERRIDE CODE Unlike override switches easily found and defeated this security system allows the consumer to programa personal override code offering a higher level of security To take advantage of this option programmable feature 10 must be selected for the Custom Code Opti
38. y the lesser vibration will be deleted If strong vibration occurs the siren will sound 3 Stage 2 Omit pre amp full detect In this mode both the pre detect stage and the full trigger stage of the sensor are defeated The unit will not react to vibration of any magnitude NOTE Shock Sensor Icon Is Displayed On The LCD Panel Page 9 128 8128 9 of 24 4 Stage 3 City Mode In this mode the pre detect chirps will change from six pre warning tones to a full 10 seconds of warning chirps The full detect trigger duration will be reduced from 30 seconds to 15 seconds NOTE Sening Me stage of the shock sensor will be effective for one arming cycle only Once the system has been disarmed the very next arming cycle will cause the sensor to default to the normal operation stage To change or adjust the shock sensor press and release the ARM button of you keychain transmitter 1 Within 2 seconds of arming press and release the ARM button 1 time to defeat the pre detect stage of the shock sensor The lights will flash and the siren will chirp once 2 Within 2 seconds of step 1 press and release the ARM button 2 times to defeat the pre and full detect stages of the shock sensor The lights will flash and the siren will chirp twice 3 Within 2 seconds of step 1 press and release the ARM button times to enter the City Mode of operation The lights will flash and the siren will chirp three times While und
Download Pdf Manuals
Related Search