Audiovox LCM56 User's Manual
Contents
1. A AUDIOVOX CORPORATION LCM56 Headrest 5 6 LCD Monitor oocooo o Owner s Manual 9o o EXPLANATION OF GRAPHIC SYMBOLS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with the arrowhead within a triangle is intended to alert tell the user that parts inside the product are A The exclamation point within a triangle is intended to alert the user that important operating and servicing instructions WARNING TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD DO NOT OPEN CAUTION This product is designed to operate with a 12 volt negative ground battery system Disconnect the ground wire from the battery terminal before connect ing the electrical system Refer to the electrical connection diagram to avoid wrong connection of the electrical system Always use authorized service center for service assistance Do not operate the monitor at temperatures below 32 F 0 C or above 104 F 40 C Keep the monitor clean and dry Never attempt your own repairs This unit should be installed and re paired by qualified technicians or service personnel Do not drop the monitor or expose to strong impacts Do not expose to direct sunlight for extended periods of time Use proper insulation material to prevent short circuiting of the supply system 2 IMPORTANT2. An LCD panel and or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information system control rear or side observation or naviga tion If the LCD panel or video monitor is used for television reception video or DVD play the LCD panel or video monitor must be installed so that these features will only function then the vehicle is in park or when the vehicle s parking brake is applied An LCD panel or video monitor used for television reception video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver s seat where it will not be visible directly or indirectly to the operator of the motor vehicle A Precaution 1 Before installation verify that it will not damage electrical wires fuel lines brake lines hoses exhaust system components or any other items that will impair the operation of the vehicle 2 Ensure the cable has already been pulled through the supporting pipe before installing the base into the headrest Ensure there is no foreign material trapped inside the enclosure before installing the monitor into the base Tighten all screws bolts nuts securely for installation To avoid electrical hazards do not disassemble the cabinet of the monitor 5 Use only the supplied DIN cable Disconnect the cable from the signal source before disconnecti
3. ear View 17 18 DIN Jack DV 12V Input Red 12V DC Black Ground Audio Input L 2 Audio Input R 2 Video Input 2 Audio Input L 1 Audio Input R 1 Video Input 1 IR Repeater Connector IR Repeater Transmitter 128 6545 9 of 12 Note This cable 18 is used to connect to a Video Cassette Player or DVD player that doesn t accept the IR Repeater 1 8 3 5mm style plug 17 The IR Repeater Transmitter is provided with an adhesive that allows it to adhere to the remote sensor of the Video Cassette Player or DVD player Remove the backing covering the adhesive and place the IR Repeater Transmitter directly over the Video remote sensor of Cassette Player or DVD player D Operation 1 Connect the monitor power input plug 10 to a DC power source Red plug 12 VDC Black plug to ground 2 Connect the external video source output signal from VCP DVD TV etc to the VIDEO IN jack 13 or 16 3 Press power button 2 to turn the monitor on and off The backlight for the button will turn brighter 4 Press the volume up 5 or down 6 button to adjust the volume level 5 Press the picture button 4 to adjust the picture display characteris tics The adjustments will be shown on the On Screen Display in the following sequence Color Brightness Contrast and TINT While in the picture select mode video adjustment press the up button 5 to increase the selected adjustment level
4. est leav Fo ing a recess where the shell will be inserted NOTE Atthis point you will need to install the harness up through the area into the recess It may be help ful to follow one of the posts and tie wrap it to the post for restraint 10 Lay the flaps of the headrest ma terial down into the recess and in sert the Mounting Tray into the re cess Check for fit If it does not fit properly you may need to re move some more foam NOTE The Mounting Tray will need to be secured to the headrest either by using tie straps screws etc 11 Guide the cable through the side opening of the Mounting Tray and plug it into the Monitor Make sure the connector locks into place In sert the Monitor into the Mount ing Tray and secure the cable using tie wraps or screws 12 Turn the Monitor around and in sert it into the Mounting Tray housing Snap into place 13 Connect the Monitor power input plug to a DC power source Red plug 12 VDC Yellow plug 12 VDC Constant and Black plug to ground 14 Connect the external video source output signal from VCP DVD TV Etc to the VIDEO IN jack Test the system to verify proper installation 7 C Controls Indicators Connectors Front View C c ml IR Sensor Power Button Source Button Picture Select Button Volume Up Button Volume Down Button Headphone Jack AV3 In Jack ON OM PW R
5. ng it from the monitor after turning off the whole system 6 Do not use gasoline thinners or other thinning liquids to clean the unit Remove dust and stains with a damp cloth 3 B Installation Front View Top View 1 Installation will vary from vehicle to vehicle as headrests in vehicles are not standard 2 This unit is intended for installation by professional installers 3 The kit consists of the screen assembly a clam shell housing a trim ring 1 key to remove the screen from the housing and a wiring harness Headrest Mounting 1 Remove the headrest ien from the vehicle for easi TOROS Ua Headrest est installation S 2 Layheadrest on a flat sur F7 face 3 Centertrim collar on head gt gt rest as shown NOTE Depending on the angle of the headrest the Trim Ring and housing may be mounted upside down 4 Using a Permanent Marker mark headrest material along the interior of the Trim Ring 5 Remove the Trim Ring and mark an X from cor ner to corner as shown 6 Using the utility knife cut the headrest material along the X lines Do not cut the mate rial along the other lines at this time 7 This will leave you with an cut as shown 8 Pull the flaps up and cut the foam beneath the material to the proper depth Cut all four sides of the foam 9 Using your fingers tear the p foam out of the headr
6. or press the down button 6 to decrease the level 10 THIS PAGE LEFT BLANK INTENTIONALLY E Specification 1 Type 3 Power Source 4 Power Consumption 5 Connection Terminals 6 Operating Temperature 7 Storage Temperature 8 Dimensions 9 Video Format Color Liquid Crystal Display LCD Monitor 12 VDC 0 5W 2 RCA AV Inputs DC 12V Input IR Input 32 F 104 F 0 C 40 C A F 176 F 20 C 80 C 140 0W x 110 0H x 26 5D mm NTSC 2002 Audiovox Electronics Corp Hauppauge NY 128 6545 12
Download Pdf Manuals
Related Search