Audiovox GMNAV1 Installation Manual
Contents
1. a full user s manual from WWW ADVENTPRODUCTS COM If the picture is not centered or does not fill the screen correctly you can adjust the picture size Access the settings menu by pressing the Menu button on the side of the Nav Interface Module Use the Menu button to scroll through the options and or buttons to adjust the value Contrast Brightness and Saturation are all screen adjustments for picture quality Position H and V are for Horizontal and Vertical Position use to adjust to fit factory screen as needed IR AV1 IR AV2 NOT USED Select NONE to insure proper operation Guide L Guide R CNTRL These are controls for the position of the Parking Lines By selecting or you can move the position of the lines to match the vehicle width 5 H Size V Size This will adjust the picture to meet the full screen size of the OEM panel oe a Setup Menu Contrast Brightness Saturation Position H Position V NOT USED NOT USED CU eee 0 Guide R Guide CNTRL Specifications No Name Parameters S Videoinput_ 0 7Vpp with 75 Q impedance a Synchronized signal strength 3 5Vpp with 5K impedance negative pulse synchronization RGB resolution By changing DIP4 user can select HD VGA or normal HD 800X480 or VGA 640X480 Normal NTSC vertical 240 or 234 Av1 Av2 cam video 0 7Vpp with 75 O impedance Av1 Av2 cam format NTSC PAL SECAM Automatic switch e romao women Trigger level threshold Reverse an2. of any vehicle trim removal process consult the OEM service manual e Removing vehicle trim panels in extreme hot and cold climate could result in some vehicle damage Use care when removing all vehicle trim e Using tape on vehicle trim panels could help limit any scratches and or marring Use plastic trim panel removal tools whenever possible The instructions included in this kit are current at the time of printing It is designed as a guide to help make the installation of this product successful Always use caution and ask for assistance if you are not sure how to proceed Voxx International is not responsible for any damage that may occur during installation or any changes to the vehicle interior Installation Removal of the Radio control center is required for installation Vehicle Specific instructions are available on line at www voxxuniversity com After the components are removed connect the following The navigation module can be located behind the radio or to either side In some vehicles it may be located below the radio We have included a extension Video LVDS cable for these cases Determine your exact mounting location to insure you route your wires correctly Remove the Blue Video Cable and the Black power harness connection from the rear of the panel housing Using the supplied power harness cable plug into the OEM panel and connect to the OEM cable Plug the supplied Video cable in to the panel and the factor
3. Cable This is used for map updates Route the cable from the module to the glove box for future use as needed Connect to the Nav module GPS Antenna The antenna must be mounted in a location where it has a clear view of the sky Center of the dash by the glass is recommended NOTE f reception is poor re locate to another area and re test The GPS antenna cannot be blocked by metal surfaces and should be visible for best reception 12 Nav activation switch Included with this kit are two pieces of SWC replacement switch covers These covers will fit some of the vehicle applications such as the Malibu Since changes happen quickly at the OEM we suggest you compare the enclosed switch covers with the vehicle you are installing in If they are the same size and shape they will work We offer several ways to trigger the change between Navigation and the OEM functions A Touch and press for 3 or more seconds anywhere on the panel that does not have an active switch or icon You can again do this to exit navigation B Install the included Navigation dash switch Pressing this will toggle you in and out of Nav or the aux inputs if using them C Install the OEM steering wheel switch cover NOTE nstaller assumes all liability for the switch buttons and controls This is a delicate procedure and if not done correctly damage can occur Voxx is in no way responsible for damage 1 Using a nylon pry tool wrap the tool with masking tape wher
4. HI VENT GMNAV1 Advent Integrated Navigation This interface is designed to integrate Navigation into select Buick and Chevrolet Systems INSTALLATION MANUAL What s in the Box The following items are supplied with the GMNAV1 es Prior to Installation Care must be taken when installing this accessory to ensure damage does not occur to the vehicle The installation of this accessory should follow approved guidelines to ensure a quality installation Read entire instructions thoroughly before starting This document covers such items as e Vehicle Protection use of covers and blankets cleaning chemicals etc e Vehicle Disassembly Reassembly panel removal part storage etc Electrical Component Disassembly Reassembly battery disconnection connector removal etc NOTES Removed Parts Inspect the vehicle for any damage Place all removed parts on a protected surface in an area where they will not be damaged Connectors When disconnecting connectors do not pull on the wires pull on the connectors Vehicle Preparation and Protection CAUTION e Do not touch the positive terminal with any tool when removing cable e Be sure ignition key is in the OFF position during install e Donot disconnect ANY airbag connectors or indicators Doing so may result in activating a diagnostic code These codes will require the dealer to perform the reset procedure and may be charged a dealer fee e Ifyou are unsure
5. d gt 5V trigger switching Output current of additional control Maximum current of 2A port 1 2 7 Operating temperature range 40 85C 15 6 X9 2 X 2 2 Cm For Technical Support Please Call 1 800 323 4815 TETTRE DIP Settings LWOS Cable to be plugged in OEM Radio OEM LVDS Cable to be plugged here Fea RGR PRCT ERE RHE z iu _ 4 i LELE 7 E ae Co ee SPS Antenna ToL TAT OTIC TeCTa Tie tari ertorie if r I E a pg Heaa lip Sows i Aes Eron ANT i mpo Wl Navy audio Go OUTPUT ee CAN Box se lsak 0 A ee _ _ _ sl is 5 4 i SG Slat l PAY fiaa lusa o Navigation Interface a ace AUX u iSe Data 1 r a a ao Cae a EE N nan Pomi eo Power Harness 3 Tor Equinox Terrain Vehicle Specific Instructions Tech Tips and Installation notes can be found at WWW AUDIOVOXUNIVERSITY COM NDV ENT Voxx Electronics Corporation Hauppauge NY 11788 Technical Assistance 1 800 323 4815 WWW ADVENTPRODUCTS COM 2014 Printed in China 128 9396
6. e it will contact the steering wheel This will eliminate scratching of the painted surface Carefully and gently pry upward from the bottom center Do not pry from the side or top as you will damage the retainer clips You are only removing the cover 2 Select the switch cover that best matches the color of the factory switch and carefully snap the cover in place on the steering wheel DIP Switch Settings Up is OFF Down is ON for Dip Switches 13 Check the DIP Switch settings Dip 1 UP External RGB input Not Used Dip 2 UP Video Input 1 Off Dip 3 UP Video Input 2 Off Dip 4 DOWN OEM High Resolution Screen On Dip 5 UP For OEM Camera UP After Market Camera Down Dip 6 UP This is not used Dip 7 UP New GVIF Reverses Video Polarity UP Default Dip 8 UP Screen Size Selection 8 screen UP 14 Check to be sure the Map SD Card is installed in the Navigation unit Double check all connections and then reconnect the vehicle battery Navigation Interface Operation CUE Equipped Vehicles To change the OEM radio to Navigation Mode Press on an open area on the screen for 3 seconds Press the Nav switch if installed Press the SWC Nav switch for 3 or more seconds if installed Exit Navigation by Pressing again on an open area of the screen for 3 seconds Press the Nav switch Press the SWC Nav switch for 3 or more seconds if installed For Navigation operation see the included quick start guide or download
7. y cable into the Nav module video connection NOTE The panel may look different than the picture above but the connections are the same 4 Connect the CAN module to the power harness connection Connect the CAN to Nav interface cable to the main Nav module as shown in the wiring diagram The white wire on the CAN module must be connected to the CAN wiring behind the main radio chassis Remove the radio chassis CD player by removing 4 screws Once it is out of the dash you will connect the white CAN wire to the Dark Green CAN wire shown here This will allow access of the NAV through the SWC switch supply Reverse gear notification for a camera and Parking line information when using a add on camera Will not show parking line info on the OEM camera External Speaker The system utilizes an external speaker for Nav Audio Select a location to mount the speaker where it can be clearly heard by the driver Some suggestions are below the dash or the center console base If needed or for custom installation this can be wired to any standard 4 ohm speaker The Nav module has the ability to add a backup camera and 2 AV inputs The module will support the factory backup camera if the vehicle is equipped with this 8 Aux Video There are 3 RCA video inputs on the Nav Module If these are used you must switch on the DIP switch that corresponds to that input Aux Audio Use the included harness for Audio in and Out USB Update
Download Pdf Manuals
Related Search