Audiovox CR-308 User's Manual
Contents
1. knob to select the i gt desired station PRESET CHANNEL There are up to 10 preset channels in each band Press PRESET knob to select preset channel stored in memory Operation must be in radio on 1 Press MEMORY knob until FM oy Hate MEMORY MEMORY flashes on screen oac I I e 2 Press PRESET knob to we i pa increase channel press MEMORY PRESET knob to decrease Ha E channel 3 Press MEMORY knob to store a E 7 RADIO RECEPTION FOR BETTER RECEPTION FM Extend the FM wire antenna fully AM Turn the unit to find the position which gives the best reception NOTE Do not connect FM wire antenna to external antenna RESET FUNCTION To delete all setting information by pressing RESET knob on the bottom of unit at the same time the system will resume the specified initial state which set before leaving the factory RESET SPECIFICATION Power requirements AC 120V 60Hz Power consumption 4w Specification and external appearance are subject to change without advance notice due to continuous product improvement Printed in china 811 CR3891 0102. DIGITAL CLOCK RADIO OPERATION INSTRUCTION LOCATION OF CONTROLS WARNING EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with an arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute an electric shock to persons WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE maintenance servicing instructions REFER SERVICING TO QUALIFIED in the literature accompanying the SERVICE PERSONNEL epplance The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE PRECAUTION Follow the advice below for safe and appropriate operation ON PLACEMENT Do not use the unit in places which are extremely hot cold dusty or humid Place the unit on a flat and even surface Do not restrict the air flow through the ventilation slots by placing the unit on soft furnishings by covering the unit with a piece of cloth or by placing the unit on a carpet ON AC VOLTAGE e Before using check that the rated voltage of your unit matches your local voltage ON SAFETY e When connecting and disconnecting the AC cord grip the plug instead of the cord its
3. elf Pulling the cord may damage it and create hazard e When you are not going to use the unit for a long period of time disconnect the AC power cord FCC INFORMATION FOR USA ONLY This device complies with Part 15 of FCC Rules Operations are subject to the following two conditions 1 This device may not causeharmful interference and 2 This device must accept any interference received including interference that may cause undesirable operations Should any trouble occur disconnect the AC power cord and refer servicing to qualified personnel SET MEMORY Knob POWER ON OFF Knob BAND Knob SNOOZE Knob 1 10 ALARM2 Knob 2 3 4 5 BUZZER RADIO Switch 6 7 8 9 11 H TIME SET M Hour Minute TUNING Control 12 SLEEP Knob 13 DIMMER Knob 14 ALARM1 Knob PRESET Knob PRESET Knob DISPLAY 15 RESET Knob COLORS Knob 16 VOLUME Control 3 od kolod a mal ci e The clock display and adjustment must be in radio off Connect AC power the clock digital will indicate on screen e Check that the rated voltage of your unit matches your local voltage 2 Press SET MEMORY knob the clock digital will flash RS 3 Press H TIME SET M TUNING knob to adjust the Hour Minute When GM appears it comes to set noontime H TIME SET TUNING 4 Press MEMORY knob to store DIMMER FUNCTION e Pres
4. inutes if not press any knob amgoze e To clear the preset alarm time by pressing 3 ALARM1 or ALARM2 knob twice until 4 or fe icon flashes Alarm function will be cancelled automatically after few seconds To activate the preset alarm time press ALARM1 or ALARM2 knob Tay a repeatly until 1 or fe icon appears on the display Press ALARM1 or ALARM knob to check and modify the preset ALARM time Can not set Radio and Buzzer alarms at the same time e The clock radio alarms only one time if the alarm setting time of ALARM1 and ALARM2 are same SLEEP TIMER SETTING 1 Press SLEEP knob to set the sleep time 2 Press SLEEP knob to repeatly select the desired time changed cyclically as bellow 100 90 80 70 60 02 lt 10 20 lt 30 lt 40 50 The power will be off automatically once unit reaches the sleep time To clear the preset sleep time by pressing SLEEP knob till steep 2 disappears from the display RADIO RECEPTION VOLUME ADJUSTMENT vol i Adjust the VOLUME control to i obtain the desired volume level before using the unit AM FM SELECT BAND 1 Press POWER ON OFF knob to turn on radio we 2 2 Press BAND knob to repeatly gt select FM or AM the band changed shown in display 3 Press H TIME SET M ye TUNING
5. s DIMMER knob to change the LCD display brightness e Press COLORS knob to repeatly select the multi color display changed cyclically as below RED ORANGE GREEN DUAL ALARM SETTING Operation must be in radio off The unit can alarm twice per day by setting different alarm time in ALARM1 and ALARM2 BUZZER The radio can wake up to alarm RADIO with Radio or Buzzer sound by putting switch in RADIO or i BUZZER position ALARM1 SETTING 1 Press ALARM1 knob R ALARM icon will flash ea 2 Press MEMORY knob timer icon will flash 3 Press H TIME SET M He TIME SET TUNING knob to adjust Hour TONING Minute gt 4 Press MEMORY knob to store F y ALARM2 SETTING 1 Press ALARM2 knob g icon will flash 2 Press MEMORY knob timer icon will flash _ 3 Press H TIME SET M TUNING knob to adjust Hour Minute He TIME SET M TUNING 4 Press MEMORY knob to store DUAL ALARM SETTING NOTE The clock radio will wake up to Radio or Buzzer when alarm timer comes to the preset time After about 10 seconds the volume of alarm will increase To stop Radio or Buzzer sound by pressing any knob The alarm will continue after 5 minutes if press the SNOOZE knob The Radio or Buzzer sound will automatically turn off after 60 m
Download Pdf Manuals
Related Search