Audiovox ACA400 Installation Manual
Contents
1. Packing List ACA400 e 1 piece CMOS Camera 1 qty e piece Hardware pack with nut and retainer clip e 1 piece 22mm Hole Saw e 1 piece Power cable e 1 piece 21 RCA Video Extension Cable 1 qty ACAS500 e 1 piece CMOS Camera 1 qty e piece Hardware pack with nut and lock washer e 1 piece Power cable e 1 piece 21 RCA Video Extension Cable 1 qty Camera Installation Look for a location that will give you the best view behind the vehicle This should not be directly next to or under a reverse backup lamp as it may blind the camera at night Avoid license plate lamps as well as they too can blind the camera at night Before drilling determine the best way to run the power wires to the reverse lights amp the extension cable through the car Insure that your route will not interfere with any safety equipment trunk release or other items on the vehicle Once your location has been confirmed AGAIN DOUBLE CHECK BEFORE YOU DRILL Look for wires sensors double metal anything that could cause a problem or damage The camera should lay flat against the mounting surface for proper installation and weather proofing After selecting a mounting surface either remove the panel if possible or tape off the area to be drilled with masking tape in order to protect the surroundings For the ACA400 Camera we include a 22mm hole saw Use this drill bit to drill through your mounting surface for the camera Make sure that there is2. ACA400 AN AUDIOVOX ELECTRONICS CORP Model ACA400 amp ACA500 Reverse Camera Installation Manual FEATURES High Resolution 1 4 CMOS Color Camera Compact Zinc Alloy Die Cast Body Waterproof Housing 150 Degree Wide View Angle Minimum Illumination lt 0 3Lux Resolution 672 x 520 Waterproof IP67 Rated Operating Temp 30c to 70c Current Max 80mA TABLE OF CONTENTS Y arnilis eei ea eer ti 2 Product DesCriphon sers esrsiisie eE 4 Packing List See te Seek o I te 5 Camera Installation e ies myers eee sense ne 6 Camera Wiring Diagrams ie es Rte 9 Troubleshooting 2m a Seine uses 10 Warnings The product is intended to assist in safe driving and to allow the driver to have a broader rear view while the vehicle is in reverse You as the driver are solely responsible for the safe operation of your vehicle and the safety of your passengers according to local traffic regulations Do not use any features of this system to the extent it distracts you from safe driving Your first priority while driving should always be the safe operation of your vehicle Audiovox Electronics Corporation cannot accept any responsibility whatsoever for accidents resulting from failure to observe these precautions or safety instructions This product utilizes high voltage Any unauthorized modifications or damage to the product may result in electrical shock Han
3. other end of the extension cable to the camera Yellow RCA connected to the Video input Camera Wiring Monitor Camera Blue Loop Cut to switch to non mirror image Green Loop Cut to shut off parking lines evening ining Camera NOTE After cutting wires use electrical tape to protect exposed ends 9 Troubleshooting Symptoms Solutions Check you reverse trigger wire for your monitor 2 Check the rear view camera wiring connection No video signal appears 1 while reversing the vehicle and RCA connection Video image is not sharp 1 Clean the camera lens enough 2 Make sure a Video cable was used and not an Audio cable as the extension Camera stays on when not Check the camera power wiring or your reverse in reverse trigger wire 10 12 MONTH LIMITED WARRANTY Appiles to Audiovox Moole Video Products AUDIOVOX ELECTRONICS CORP ine Company warrants to the original retai purchaser of this product that should this product or any part thereof under normal use and conditions be proven defective in maternal or workmanship within 12 monins from the cate of original purchase such defect s will be repaired or replaced with reconditoned product at ne Company s option without charge for parts anc repair labor A game controller F suppilec Is simfary warranted for ninety 90 days To obtain repair or replacement within the terms of this Warranty Me product is to b
4. IS OR ANY OTHER WARRANTY No person or representative Is authorized to assume for the Company any liability other than expressed herein In connection with the sale of this product Some states do not allow limitations on now long an impilec warranty ists or the exclusion or Imation cf incidental or consequential damage so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also nave other noms which vary from state to state Audiovox Bechonics Corporation 150 Marcus Siw Hsuppeuge New York 11785 e 1 500 645 4954 128 5495F ES For Customer Service Visit Our Website At www audiovox com Product Information Photos FAQ s Owner s Manuals 2007 Audiovox Electronics Corp 150 Marcus Blvd Hauppauge N Y 11788 12
5. dle all components with care Inspect regularly for damage to components and cabling You are responsible for ensuring that the installation of this product does not void or affect the vehicle manufacturer s warranty Audiovox Electronics Corporation or its subsidiaries are not liable in full or in part for improper installation resulting in loss or damage to your property or for voiding all or part of the vehicle manufacturer s warranty Do not apply excessive force to any of the components contained within this kit Excessive force used before during or after installation that results in a damaged or non functional part will void all warranties Please follow the procedures in this installation manual Improper installation or modification of this product will void all warranties 3 Product Description This revolutionary camera design integrates a backup camera with your vehicle The camera is easy to mount on your car truck or van but ALWAYS CHECK AND DOUBLE CHECK before drilling or mounting any item on the vehicle Make sure there are no obstructions in front of the camera behind where mounting the camera and that the wire can be run without pinching or interfering with any other item This Wired Camera is compatible with most monitor TFT screens and can be connected using a standard RCA connector If an extension lead is required be sure to use a Video cable with RCA type ends An Audio cable will cause poor picture quality
6. e Gelivered win proof of warranty coverage e g dated DIE of sale specficallon of de ct s transportation prepaid to e Company at the address shown below Tnis Warranty does not extend 10 the elimination of extemally generated static or noise to correction of antenna problems to costs Incurred for installation removal or reinstalation of the product or to Gamage to digital memoryimedia devices gaming devices discs speakers accessories or venicie electrical systems This Warranty Goes not apply to any product or part thereof which in the opinion of the Company has suffered or been damaged tnrougn alteration Improper Installation mishandling misuse neglect accident or by removal or defacement of the factory serial number bar code label s THE EXTENT OF THE COMPANY S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID 5Y PURCHASER FOR THE PRODUCT This Warranty Is In lleu of all other express warranties or llabllities ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTASILITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY BE LIASLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF TH
7. not a metal lip or double metal in this area as it could damage the hole saw blade For the ACA500 Camera use a 5 16 drill bit to create your hole to mount the camera After drilling carefully remove any burs or sharp edges so you do not damage the cable when pulling it through Coat the edge of the hole with rust preventative On the ACA400 remove the backing on the double sided tape on the top of the camera base before inserting into the mounting location Carefully route the camera cable connector through the hole and insert the camera into the hole 6 Use the included hardware to secure the camera in place DO NOT OVERTIGHTEN the hardware 7 Wire the Camera s power wire to the vehicle s reverse lamp a Locate the reverse lamp in the tail light assembly b Using a crimp connector or by soldering attach the red wire to the positive 12 volt wire from the reverse lamp This should only have power when the car is in reverse gear and the white lamp it illuminated Attach the black wire to the ground Negative 12 Volts only c Ifa trigger wire is required at the front of the vehicle or you wish to power your camera from the front of the vehicle use the additional red wire on the video extension cable NOTE Do not connect to the reverse lamp and to power at the front of the vehicle This will cause the reverse lamp to turn on any time you power the camera 8 Run the extension cable to the location of the monitor and connect the
Download Pdf Manuals
Related Search