Atwood Mobile Products MPD 85810 User's Manual
Contents
1. are available to replace Fic 1 G or F respectively There must be a half hole at the bottom of the housing in order to use the pull pin If using a pull pin assemble it to the housing per its instruction manual OPERATION A WARNING MOVING PARTS CAN CRUSH OR CUT OR PINCH POINT e Keep hands and clothing away from moving parts A WARNING TRAILER CAN MOVE OR COLLAPSE e Never exceed rated capacity of stabilizer e STABILIZERS ARE NOT DESIGNED TO BE USED AS TRAILER JACKS Do not use the stabilizer to lift or support the trailer during tire changes axle work or trailer servicing the trailer weight will exceed the capacity of the stabilizer The stabilizer is designed to stabilize a portion of the trail er s weight Support the front end of the trailer with structural stands rated for the GVWR of the trailer e Chock both sides of trailer wheels before operating stabilizer e All legs must touch the ground or the surface at the same time e Retract stabilizer completely before towing trailer A CAUTION SECURE TRAILER BEFORE TRAVELING e Before retracting ensure there is no load on the stabilizer Securely latch hitch before retracting stabilizer e Lock pin spring clip must be positioned around stabilizer and secured over end of pin on opposite side of housing tube This pre vents pin from coming out during travel Fic 1 G FOR 2 0 STABILIZER insure the ball detent pin is fully extended through the leg FIG 1 F TO EXTE2. Consumer Service Department 1120 North Main St Elkhart IN 46514 Telephone 574 264 2131 Fax 574 206 9713 Warranty claim service must be performed as approved by the Atwood Consumer Service Department Warranty replacement hardware systems and components or parts will be furnished freight prepaid Labor cost to repair or replace will be limited to the amount of the original purchase price of the systems and components The replaced warranty products or parts become the property of Atwood Mobile Products and must be returned to the Atwood Consumer Service Department freight prepaid unless prior arrangements have been agreed to This limited warranty is valid only when the product is applied installed maintained and operated in accordance with this Atwood Installation Maintenance and Operating Manual Any deviation from these recommended specifications must be approved in writing by Atwood Any implied warranties are limited to the duration of this limited warranty as stated above Atwood does not assume responsibili ty for consequential damage or loss including loss of use of vehicle loss of time inconvenience expense for gasoline tele phone travel lodging loss or damage to personal properties or loss of revenues Some states do not allow limitations on how long an implied warranty lasts or limitations on consequential damages so the above limitations may not apply to you This limited warranty gives you specific legal right
3. Atwood 1120 North Main Street Elkhart IN 46514 PHONE 574 264 2131 FAX 574 206 9713 INTERNET http www atwoodmobile com ENGLISH SAFETY ALERT SYMBOLS Safety Symbols alert you to potential personal safety hazards Obey all safety messages following these symbols A CAUTION avoid possible injury and or property damage A WARNING avoid possible injury or death For your safety read all instructions before operating landing legs Installer Provide these instructions to the consumer Consumer Keep documents for future reference DO NOT EXCEED CAPACITY STABILIZER 2 SQUARE 2 5 SQUARE MAXIMUM VERTICAL LOAD 3 000 LB 6 000 LB A WARNING TRAILER CAN MOVE OR COLLAPSE Never exceed the rated capacity STABILIZERS ARE NOT DESIGNED TO BE USED AS TRAILER JACKS Do not use the stabilizer to lift or support the trailer during tire changes axle work or trailer servicing the trailer weight will exceed the capacity of the stabilizer The stabilizer is designed to stabilize a portion of the trailers weight Support the front end of the trailer with structur al stands rated for the GVWR of the trailer The pin between the housing and drop tube should be the same diameter as the adjustment hole in the drop tube Otherwise prema ture wear on drop tube and housing can occur INSTALLATION A CAUTION HAZARDOUS FUMES Adequate ventilation must be provided when welding WELDING INSTRUCTIONS M 1 G OR ST
4. ICK Attach with 3 16 fillet weld minimum M 1 G WELDING Use A W S ER 70S 3 or 6 wire or equivalent with a diameter of 035 045 The recommended shielding gas mixture is 75 95 Argon amp 25 5 CO STICK WELDING Use E6011 A W S welding rod or equivalent Recommended machine settings for specific electrode diameters are as follows 1 8 electrode set power between 115 130 Amps DC or 5 32 electrode set power between 140 160 Amps DC Weld two sides of housing to structural attachment point on trailer surface FIG 3 A 4 A amp 4 B Use a minimum of 4 of 3 16 fillet lin ear weld total on each side stich or continuous Fic 4 A amp B See welding instructions When locating housing on trailer make sure access for lock pin is available for easy adjustment Assemble foot pad Fig 1 D to drop tube Fig 1 B with bridge pin clip Fig 1 C and clevis pin Fig 1 E for 2 5 square stabilizer Nm LITERATURE NUMBER MPD 85810 TELESCOPING STABILIZER eInstallation eOperation Maintenance Effective 11 21 07 3 Assemble drop tube Fic 1 B to 2 5 square housing Fig 1 A ina fully retracted position using lock pin Fic 1 G For 2 square assemble drop tube to housing with the ball detent pin Fic 1 F Mount footpad with its length running from front to rear of the trailer NOTE Optional spring loaded pull pins Fig 2 A Pull Pin or Fic 2 B on the 2 5 square stabilizer SNAPS
5. ND THE STABILIZER Remove the pin in the drop tube or if you have a pull pin that doesn t remove pull the handle pin so the pin is disengaged Let the drop tube fall to the ground and re pin in the nearest adjustment hole TO RETRACT STABILIZER Make sure there is no load on the stabiliz er Remove pin or disengage the pull pin and raise the drop tube re pinning it in the highest position Fully retract the legs so that the foot pad is higher than the lowest point of the trailer to prevent dragging while going over a curb Before towing check for maximum clearance between ground and bot tom of stabilizer MAINTENANCE PART IDENTIFICATION 1 Before use inspect drop tube and inner housing tube Replace if bent or damaged KONE BAYER DESCRIPTION a Extend stabilizer as far as possible clean drop F tube and housing tube Coat exposed surface of 1 A 480921 Housing Tube Tube du v rin tubes with silicone spray lubricant 1 B 480922 Drop Tube Tube t lescopique Should problems or questions arise contact your Bridge Pin Goupille de pont dealer the trailer manufacturer or Atwood s Service Foot Pad Department ara Se eat Clevis Pin Goupille d articulation 1 F 480952 Ball Detent Pin Cheville a bille Lock Pin Goujon de blocage 2 0 SQ 2 5 SQ a OPTIONAL Pull Pin FOR 2 5 SQ ONLY mM WELD ON TWO SIDES OF e SOUDER LES DEUX COTES DU HOUSING TUBE ON STRUCTURAL TUBE
6. TELESCOPIQUE AU POINT ATTACHMENT POINT ON TRAILER D ATTACHE STRUCTUREL SITU SUR LA REMORQUE e UTILISER UN MINIMUM DE 4 0 A e USE A MINIMUM OF 4 0 OF WELD TOTAL ON EACH SIDE PO DE SOUDAGE AU TOTAL DE STICH OR CONTINUOUS CHAQUE C T ALTERN OU SEE WELDING INSTRUCTIONS CONTINU e VOIR LES IN STRUCTIONS DE SOUDAGE 5 0 MAX 12 7 CM MAX 1 0 RETRACTED 2 5 CM RENTRE 17 0 EXTENDED 43 2 CM SORTI A ATWOOD LIMITED WARRANTY HARDWARE SYSTEMS amp COMPONENTS Atwood Mobile Products warrants to the original owner this product will be free of defects in material and workmanship for a period of two years from the date of purchase Atwood s liability hereunder is limited to the replacement of product repair of product or replace ment of product with a reconditioned product at the discretion of the manufacturer The warranty is void if the product has been dam aged by accident unreasonable use neglect tampering or other causes not arising from defects in material workmanship The war ranty extends to the original consumer purchaser of the product only and is subject to the following conditions 1 For two 2 year commencing with the date of purchase Atwood will replace or repair any Hardware System amp Components that are found to be defective by Atwood in material or workmanship In the event of a warranty claim the owner must contact the Atwood
7. s which may vary from state to state
Download Pdf Manuals
Related Search