Atlas Guardian Pro 240 Series User's Manual
Contents
1. trol Reposition light control Flashing is normal under these conditions Replace the flood lamps with new high quality PAR 38 lamps Make sure the metal lamp protectors are installed Reposition flood lamps to keep area below the light control relatively dark FIVEYEAR LIMITED WARRANTY Atlas Lighting Products Inc warrants against defects in materials or workmanship for a period of five years from the date of purchase for use and agrees to repair or at our option replace a defective unit without charge for either parts or labor IMPORTANT This warranty does not cover damage resulting from accident misuse of abuse lack of reasonable care the affixing of any attachment not provided with product alteration of any attachments factory installed loss of parts or subjecting the fixture to any but the specified electrical service This warranty does not cover failure of the bulb due to accidents abuse misuse vandalism power surges and acts of nature such as lightning damage No responsibility is assumed for any special incidental or consequential damages Damages occurring during transit are not covered by this warranty including UPS shipments To obtain warranty service mail sales receipt as proof of purchase date and a brief explanation of the nature of the defect to the address listed below You will receive by mail a Return Goods Authorization number and full instructions for returning defective merchandise All r2. gt TEST 1520 MANUAL MODE Manual mode only works at night because daylight returns the sen sorto AUTO Flip the light switch off for one sec ondthenbackontotogglebetween 1 Second OFF AUTO and MANUAL MODE An Manual mode works only with the ON TIME switch in the 1 5 or 20 i position back on 240 028 A 598 1094 04 Mode Switching Summary Move ON TIME Switch to 1 5 or 20 minutes Flip light switch off for one second then back on MANUAL MODE If you get confused while switching modes turn the power off for one minute then back on After the cali bration time the control will be in the AUTO mode Dual Light Level Timer Light comes on half bright for selected time after dusk Off 3 hr 6 hr until dawn Selecting OFF disables this feature The motion sensing features will continue to work as described in this manual If motion is sensed the light turns on full bright for the ON TIME 1 5 or 20 minutes then returns to dim mode INSTALLATION For easy installation select an existing light with a wall switch for replacement For best performance mount the fixture about 8 ft 2 4 m above the ground NOTE If fixture is mounted higher than 8 ft 2 4 m aiming the sensor down will reduce coverage distance Wall Mount Eave Mount For under eave installation the sensor head must be rotated as shown in the next two steps for proper operation
3. switch to 1 5 or 10 minutes Lights come on for no apparent reason 1 Light control may be sensing small animals or auto mobile traffic Range is set too high Dual Light Level is on 1 Re aim light control Reduce range The fixture is operating normally under these condi tions Lights turn off too late in Relocate light control or use 3 hr or 6 hr setting Dusk to Dawn setting Light control may be installed in a relatively dark loca tion 1 Reposition the flood lamp away from the light control Lights stay on continu 1 Afloodlamp is positioned too close to the light control ously or pointed at nearby objects that cause heat to trigger the light control The light control may be picking up a heat source like an air vent dryer vent or brightly painted heat reflective surface Light control is in manual mode or nearby objects Reduce range Switch light control to AUTO Lights flash on and off Lights flash once then stay off in manual mode 598 1094 04 1 Heat or light from the flood lamps may be turning the light control on and off Heat being reflected from other objects may be turn ing the light control on and off Light control is in the TEST mode and warming up Light may be leaking through the flood lamp reflec tors Light control is detecting its own lights 1 Reposition the flood lamp away from the light con
4. Atlas Lighting Products GUARDIAN pro 240 SERIES Models MLGC240B MLGC240W Features e Turns on lighting when motion is detected e Automatically turns lighting off e Dual Light Level Photocell keeps the lighting off during daylight hours LED indicates motion was sensed day or night This package includes Bulb 0 Rubber Plug tL j Plastic Hanger Cover lt Y Plate ul I 2 Wire Connectors a Mounting Bolt Mounting Strap Gasket 6 Screws 2 Shells 3 sizes included 2008 Atlas Lighting Products Inc Requirements The light control requires 120 volts AC If you want to use Manual Mode the control must be wired through a switch Some codes require qualified electrician This product is intended for use with the enclosed gasket and with a junction box marked for use in wet locations installation by a OPERATION On Time Works Day Night 5 Seconds x x 1 5 or 20 Min x To Dawn X 3 6 Hr to Dawn X Dual Light Level resets to Auto Mode at dawn Note When first turned on wait about 1 2 minutes for the circuitry to calibrate TEST Put ON TIME switch on the sensor bottom to TEST and the Dual Light Level switch OFF ON TIME DUAL LIGHT LEVEL TEST 1520 Off 3 6 Dusk to Dawn AUTO Put the ON TIME switch in the ON TIME 1 5 or 20 minute position lt
5. and to avoid the risk of electrical shock For eave mount only O Swingthe sensor head towards the clamp screw joint O Then rotate the sensor head clockwise 180 so the controls face down Controls gt LI Controls lt If the sensor pops out of the ball joint loosen the clamp screw and push the sensor back into the ball joint Tighten the clamp screw when done 598 1094 04 Wire the Light Control A WARNING Turn power off at circuit breaker or fuse O O O Mounting Black to Strap Remove the existing light fixture Install the mounting strap as shown using two screws that fit your junction box The plastic hanger can be used to hold the fixture while wiring The small end of the plastic hanger can be threaded through the hole in the center of the cover plate The small end then goes into one of the slots on the mounting strap Route the light control s wires through the large gasket holes Twist the junction box wires and fixture wires together as shown Secure with wire connectors Junction box ground wire to green ground screw on fixture 598 1094 04 Mount the Light Control 3 Align the light control cover plate and cover plate gasket Secure with the mounting bolt Align the three slots in the decorative shell with the bulb holder pins Push the shell in and then twist clockwise to lock Repeat for other shell Shell Slot 3 Pu
6. eturned goods must be accompanied by a Return Goods Authorization number issued by Atlas Lighting Products Inc NOTE No other warranty written or verbal is authorized by Atlas Lighting Products Inc This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above exclusion and limitations may not apply to you For information regarding replacement parts please write to Atlas Lighting Products Inc Attn Customer Service Department P O Box 2348 Burlington NC 27216 6 598 1094 04 Notes Notas 598 1094 04 Notes Notas 8 598 1094 04
7. nge Maximum Coverage Angle NOTE If fixture is mounted higher than 8 ft 2 4 m aiming the sensor down will reduce coverage distance The detector is less sensitive to motion directly towards it Sensor Least Sensitive Most Sensitive 3 Loosen the clamp screw in the sensor ball joint and gently rotate the sensor O Walk through the coverage area noting where you are when the lights turn on also the LED will flash several times when motion is detected Move the sensor head up down or sideways to change the cover Aim Sensor age area Keep the sensor at Down for Short least 1 25 mm away from Coverage the bulbs O Adjust the RANGE as needed RANGE set too high may increase false triggering Aim Sensor O Secure the sensor head by Higher for Long tightening the clamp screw Coverage Do not overtighten the screw O Set the amount of TIME you want the lights to stay on after motion is detected 1 5 or 20 minutes Set the Dual Light Level switch to the amount of time after dusk you want the lights on at low level Off 3 6 Hrs Dusk to Dawn a AR WARNING Risk of fire Do not aim the bulbs at a combustible surface within 3 ft 1 m 598 1094 04 SPECIFICATIONS Sensing Angle Electrical Load Up to 70 ft 21 m 100 ft 30 5 m with Range Boost varies with surrounding temperature Up to 240 Up to 300 Watt Maximum In candescent Up to 150 Watt maximum each b
8. sh the rubber plug firmly into place O If a wet location junction box was not used caulk the wall plate mounting surface with silicone weather sealant To avoid water damage and electrical shock keep bulb holders 30 below horizontal Keep bulbs at least 1 25 mm from the sensor Do not allow the bulbs to block the lens Adjustthe bulb holders by loosening the lock nuts but do nat rotate the bulb holders more than 180 from the factory setting When screwing in the floodlamps do not overtighten TEST AND ADJUSTMENT O Turn on the circuit breaker and light switch NOTE Sensor has a 1 2 minute warm up period before it will detect motion When first turned on wait 1 2 minutes O Turn the RANGE control to the medium position halfway between MIN and MAX Dual Light Level to OFF and the ON TIME control to the TEST position MAX So ON TIME DUAL LIGHT LEVEL O n a pia 1 en el l pa RANGE MINUTES HOUR DAWN Bottom of Sensor Avoid aiming the control at Objects that change temperature rapidly such as heating vents and air conditioners These heat sources could cause false triggering Areas where pets or traffic may trigger the control Nearby large light colored objects reflecting light may trigger the shut off feature Do not point other lights at the sensor e e 240 8 ft 2 4 m 70 ft 100 ft 21 m 30 5 m Boosted Maximum Ra
9. ulb holder Power Requirements 120 VAC 60 Hz Replacement Lamp Lights will not come Upto 150Watt Maximum PAR38 Incandescent or Halogen Not CFL Bulbs Operating Modes TEST AUTO and MANUAL MODE Time Delay 1 5 20 minutes Dual Light Level 3 6 hours Dusk to Dawn Atlas Lighting Products Inc reserves the right to dis continue products and to change specifications at any time without incurring any obligation to incorporate new features in products previously sold TROUBLESHOOTING GUIDE If you experience a problem with your Light Control first follow this guide For additional assistance write to Atlas Lighting Products Inc e Customer Service Department P O Box 2348 Burlington NC 27216 POSSIBLE CAUSE SOLUTION 1 Light switch is turned off Flood lamp is loose or burned out Turn light switch on Check flood lamp and replace if burned out Fuse is blown or circuit breaker is turned off Daylight turn off is in effect Incorrect circuit wiring if this is a new installation Light control aimed in wrong direction Replace fuse or turn circuit breaker on Recheck after dark Verify wiring is correct Re aim light control to cover desired area Lights come on in day light Light control may be installed in a relatively dark location Light control is in TEST The fixture is operating normally under these condi tions Set control
Download Pdf Manuals
Related Search