AT&T TL77008 User's Manual
Contents
1. Refer to the section s on ringer selection in this user s manual Make sure the telephone line cord is plugged securely into the telephone base and the telephone jack Make sure the power cord is securely plugged in The cordless handset may be too far from the telephone base Charge the battery in the cordless handset for at least 16 hours For optimum daily performance return the cordless handset to its base when not in use 17 Appendix Troubleshooting You may have too many extension phones on your telephone line to allow all of them to ring simultaneously Try unplugging some of the other phones The layout of your home or office might be limiting the operating range Try moving the telephone base to another location preferably on an upper floor If the other phones in your home are having the same problem the problem is in your wiring or local service Contact your local telephone company charges may apply Test a working phone at the phone jack If another phone has the same problem the problem is the phone jack Contact your local telephone company charges may apply Other electronic products can cause interference with your cordless phone Try installing your phone as far away as possible from electronic devices like television sets VCRs or other cordless telephones Re install the battery and place cordless handset in the telephone base Wait for the cordless handset to re establish its2. materially defective PRODUCT During the limited warranty period the manufacturer s authorized service representative will repair or replace at the manufacturer s option without charge a materially defective PRODUCT If the manufacturer repairs the PRODUCT they may use new or refurbished replacement parts If the manufacturer chooses to replace the PRODUCT they may replace it with a new or refurbished PRODUCT of the same or similar design The manufacturer will retain defective parts modules or equipment Repair or replacement of the PRODUCT at the manufacturer s option is your exclusive remedy The manufacturer will return repaired or replacement products to you in working condition You should expect the repair or replacement to take approximately 30 days 32 Appendix Limited warranty 3 How long is the limited warranty period The limited warranty period for the PRODUCT extends for ONE 1 YEAR from the date of purchase If the manufacturer repairs or replaces a materially defective PRODUCT under the terms of this limited warranty this limited warranty also applies to repaired or replacement PRODUCT for a period of either a 90 days from the date the repaired or replacement PRODUCT is shipped to you or b the time remaining on the original one year limited warranty whichever is longer 4 What is not covered by this limited warranty This limited warranty does not cover e PRODUCT that has been subjected to mi
3. The CHARGE light will be on when charging IMPORTANT INFORMATION Use only the battery supplied with this product To order a replacement or spare battery AT amp T model 27910 part number 89 0099 00 00 or equivalent visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 Getting started Adding and registering handsets Before using a new TL77008 handset you must register it with the TL74108 TL74208 TL74308 TL74408 TL74258 TL74358 TL74458 telephone base purchased separately The TL74108 TL74208 TL74308 TL74408 TL74258 TL74358 TL74458 telephone can accommodate up to four cordless handsets e The handset provided with the TL74108 is automatically registered as handset 1 Additional handsets will be assigned numbers in the order they are registered handset 2 handset 3 or handset 4 You can register a maximum of four handsets e The TL74208 TL74258 has two handsets automatically registered as handset 1 and 2 You can register two additional handsets which will be assigned numbers 3 and 4 e The TL74308 TL74358 has three handsets automatically registered as handset 1 2 and 3 You can register one additional handset which will be assigned number 4 e The TL74408 TL74458 has four pre registered handsets so you cannot register any additional handsets to it Getting started Adding and registering handsets To register a handset to your telephone base e When first
4. T logo are trademarks of AT amp T Intellectual Property Il L P d b a AT amp T Intellectual Property licensed to Advanced American Telephones Printed in China Issue 2 AT amp T 04 08
5. connection with the telephone base Allow up to one minute for this to take place Your line cord might be malfunctioning Try installing a new line cord 18 Appendix Troubleshooting My calls fade out or cut in and out while I m using my cordless handset Other electronic products can cause interference with your cordless phone Try installing your phone as far away from the following electronic devices as possible television sets VCRs or other cordless telephones Do not install this phone near a microwave oven or on the same electrical outlet You may experience decreased performance while the microwave oven is operating If your phone is plugged in with a modem or surge protector plug the phone or modem surge protector into a different location If this solves the problem re locate your phone or modem farther apart from one another or use a different surge protector Relocate your telephone base to a higher location The phone will have better reception when not installed in a low area If the other phones in your home are having the same problem the problem is in your wiring or local service Contact your local telephone company charges may apply The charge light is off Make sure the power and line cords are plugged in correctly and securely Unplug the unit s electrical power Wait for 15 seconds then plug it back in Allow up to one minute for the cordless handset and telephon
6. equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments ACTA The label on the back or bottom of this equipment contains among other things a product identifier in the format US AAAEQ TXXXX This identifier must be provided to your local telephone company upon request The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA A compliant telephone cord and modular plug is provided with this product It is designed to be connected to a compatible modular jack that is also compliant An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines See Installation Instructions in the user s manual The Ringer Equivalence Number REN is used to determine how many devices you may connect to your telephone line and still have them ring when you are called The REN for this product is encoded as the 6th and 7th characters following the US in the product identifier e g if is 03 the REN is 0 3 In most but not all areas the sum of all RENs should be five 5 0 or less For more information please contact your local telephone company This equipment may not be used with Party Lines If you have specially wired alarm dialing equipment connected to your telephone line ensure the connection of this
7. equipment does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer If this equipment is malfunctioning it must be unplugged from the modular jack until the problem has been corrected Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents For repair procedures follow the instructions outlined under the Limited Warranty 27 Appendix FCC Part 68 and ACTA If this equipment is causing harm to the telephone network the telephone company may temporarily discontinue your telephone service The telephone company is required to notify you before interrupting service If advance notice is not practical you will be notified as soon as possible You will be given the opportunity to correct the problem and the telephone company is required to inform you of your right to file a complaint with the FCC Your telephone company may make changes in its facilities equipment operation or procedures that could affect the proper functioning of this product The telephone company is required to notify you if such changes are planned If this product is equipped with a corded or cordless handset it is hearing aid compatible If this product has memory dialing locations you may choose to store emergency telephone numbers e g police fire medical in these locations If you do store or test emergency numbe
8. purchased all optional accessory handsets show NOT REGISTERED on the screen The new handset may need to be charged for five minutes before registering to the telephone base NOT REGISTERED e Make sure your handset battery is properly installed and charged pages 5 6 e Place the unregistered handset into the telephone base After a few seconds PRESS HNDST LOC 4 SEC ON BASE will be shown on the screen e Press and hold amp HANDSET LOCATOR on the main telephone base until the IN USE light comes on about four seconds then release the button e The handset will show PLEASE WAIT for a while PRESS HNOST LOC 4 SEC ON BASE E HANDSET X REGISTERED e The handset will show HS X REGISTERED and will beep if the registration was successful Q NOTE If the registration is not successful the display will show NOT REGISTERED Reset the handset by lifting the handset out of the telephone base and then place the handset back in the telephone base Now try the registration process again Getting started Replacing a handset You may need to de register your handsets if You have the maximum number of registered handsets four and need to replace a handset OR You wish to change the designated handset number of your registered handsets You must first de register ALL the handsets and then re register ALL the handsets you wish to use Please read carefully through all the instructions on this page before b
9. with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Privacy of communications may not be ensured when using this telephone 30 Appendix FCC Part 15 To ensure safety of users the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product This produc
10. with less background noise If the other phones in your home are having the same problem the problem is in your wiring or local service Contact your local telephone company charges may apply 13 Appendix Troubleshooting My cordless handset isn t performing normally Make sure the power cord is securely plugged into the telephone base Plug the unit into a different working electrical outlet not controlled by a wall switch Move the cordless handset closer to the telephone base You might have moved out of range Reset the telephone base Unplug the unit s electrical power Wait for 15 seconds then plug it back in Allow up to one minute for the cordless handset and telephone base to reset Other electronic products can cause interference to your cordless phone Try installing your phone as far away from these types of electronic devices as possible television sets VCRs or other cordless telephones CONNECTING displays on my cordless handset Ensure that the telephone base is powered up Place the cordless handset in the telephone base for one minute to allow the cordless handset and base to resynchronize channels Move the cordless handset closer to the telephone base You might have moved out of range 14 Appendix Troubleshooting Reset the telephone base Unplug the unit s electrical power Wait for 15 seconds then plug it back in Allow up to one minute for the cord
11. ICE MAIL Using menus Press or to scroll through menu items Press MENU SELECT to select or modify a highlighted item Press orf CLEAR to cancel an operation back up to the previous menu or exit the menu display For complete instructions please refer to the manual provided with your TL74108 TL74208 TL74308 TL74408 TL74258 TL74358 TL74458 telephone If you are unable to find your manual please visit www telephones att com to read and or download the manual Getting started Installation preparation You must install and See pages 5 6 charge the battery before for easy instructions using the telephone Your product may be shipped with a protective sticker covering the handset display remove it before use For customer service or product information visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 Avoid placing the telephone base too close to e Communication devices such as television sets VCRs or other cordless telephones e Excessive heat sources e Noise sources such as a window with traffic outside motors microwave ovens refrigerators or fluorescent lighting e Excessive dust sources such as a workshop or garage e Excessive moisture e Extremely low temperature e Mechanical vibration or shock such as on top of the washing machine or work bench Getting started Charger installation 1 Plug the small end 2 Plug the larg
12. atat Q User s manual TL77008 5 8 GHz expansion handset for use with AT amp T models TL74108 TL74208 TL74308 TL74408 TL74258 TL74358 TL74458 Congratulations on your purchase of this AT amp T product Please read this user s manual for the information necessary to install your new AT amp T product For complete instructions please refer to the manual provided with your TL74108 TL74208 TL74308 TL74408 TL74258 TL74358 TL74458 telephone For customer service or product information please visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 Model TL77008 Type 5 8 GHz expansion handset Serial found on the bottom of the charger Purchase date Place of purchase Save your sales receipt and original packaging in case it is necessary to return your telephone for warranty service The ENERGY STAR program www energystar gov recognizes p N and encourages the use of products that save energy and rerh help protect our environment We are proud to mark this product with the ENERGY STAR label indicating it meets the ANRA ANR latest energy efficiency guidelines 2008 Advanced American Telephones All rights reserved AT amp T and the AT amp T logo are trademarks of AT amp T Intellectual Property II L P d b a AT amp T Intellectual Property licensed to Advanced American Telephones Printed in China Parts checklist Save your sales rec
13. d by radio receiving equip ment within range of the cordless handset For this reason you should not think of cordless telephone conversations as being as private as those on corded telephones Electrical power The telephone base of this cordless tele phone must be connected to a working electrical outlet which is not controlled by a wall switch Calls cannot be made from the handset if the telephone base is unplugged or switched off or if the electrical power is interrupted Potential TV interference Some cordless telephones operate at frequencies that may cause interference to TVs and VCRs To minimize or prevent such interference do not place the telephone base of the cordless telephone near or on top of a TV or VCR If interference is experienced moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference 24 Appendix Important safety information e Rechargeable batteries This product contains either nickel cadmium or nickel metal hydride rechargeable batteries Exer cise care in handling batteries in order not to create a short circuit with conductive material such as rings bracelets and keys The battery or conductor may overheat and cause harm Observe proper polarity between the battery and the battery charger e Nickel metal hydride rechargeable batteries Dispose of these batteries in a safe manner Do not burn or puncture Like other batteries of this type if bu
14. e announcement section in the manual provided with your TL74108 TL74208 TL74308 TL74408 TL74258 TL74358 TL74458 telephone 10 Getting started Belt clip amp optional headset To attach the To remove the belt belt clip clip Snap the belt Gently lift either of the clip into the belt clip retaining tabs shown in the figure outwards to remove the belt clip from the handset retaining tabs on both sides of the handset as shown in the figure For handsfree headset conversations use any industry standard 2 5 mm headset purchased separately For best results use an AT amp T 2 5 mm headset To purchase a headset visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 Lift the rubber flap here Plug a 2 5 mm headset into the gt jack on the side of the handset 11 Appendix Troubleshooting If you have difficulty with your telephone please try the suggestions below For Customer Service visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 My phone doesn t work at all Make sure the power cord is securely plugged in Make sure that the battery connector is securely plugged into the cordless handset Make sure the telephone line cord is securely and firmly plugged into the telephone base and the telephone wall jack Charge the battery in the cordless handset for at least 16 ho
15. e base to reset 19 Appendix Troubleshooting Clean the cordless handset and telephone base charging contacts each month using a pencil eraser or cloth Your phone might be malfunctioning Please refer to the Limited warranty section of this user s manual for further instruction My caller ID isn t working Caller ID is a subscription service You must subscribe to this service from your local telephone company for this feature to work on your phone If you subscribe to high speed internet service Digital Subscriber Line DSL through your telephone line you must install a DSL filter between the telephone base and the telephone wall jack The filter will prevent noise and caller ID problems caused by DSL interference Please contact your DSL service provider for more information about DSL filters Your caller must be calling from an area that supports caller ID Both you and your caller s telephone companies must use caller ID compatible equipment 20 Appendix Troubleshooting System does not receive caller ID when on a call Common cure for electronic equipment Make sure you subscribe to caller ID with call waiting features services provided by your local telephone company Caller ID features will work only if both you and the caller are in areas offering caller ID service and if both telephone companies use compatible equipment If the unit does not seem to be responding normally try p
16. e end of the smaller power of the smaller power adapter into the jack adapter into a power on the underside of the outlet not controlled charger then route the by a wall switch cord through the slot as shown IMPORTANT INFORMATION 1 Use only the power adapter supplied with this product To order a replacement power adapter visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 2 The power adapter is intended to be correctly oriented in a vertical or floor mount position Getting started Battery installation amp charging Install the battery as shown below After installing the battery you can make and receive short calls but replace the handset in the charger when not in use For optimal performance charge the handset battery for at least 16 hours before use When fully charged the handset battery provides approximately five hours of talk time or three days of standby time Step Step Step Plug the battery Insert the supplied Align the cover securely into the battery with the label flat against plug inside the THIS SIDE UP facing up the battery handset battery as indicated compartment compartment cover then slide matching the color it upwards until coded label it clicks into place Getting started Battery installation amp charging Step O Charge the handset by placing the handset face up in the telephone base or in the additional charger
17. eginning the de registration process To de register all handsets 1 Press and hold amp HANDSET LOCATOR on the telephone base for about 10 seconds until the IN USE light turns on and starts to flash then release the HANDSET LOCATOR button 2 Immediately press and release amp HANDSET LOCATOR again You must press amp HANDSET LOCATOR while the IN USE light is still flashing The light flashes about seven seconds If the light stops flashing pick up the handset and place back into the telephone base then start again step number one 3 The handset s will show CONNECTING and it will take about 10 seconds to complete de registration ALL handsets will show NOT REGISTERED if de registration was successful NOT REGISTERED Getting started Replacing a handset 4 To re register the handset s to the telephone base follow the registration instructions on page 8 Q NOTES 1 If the de registration process was not successful you may need to reset the system and try again To reset pick up the handset and press the PHONE FLAsSH button then press the f OFF cuear button and place the handset back into the telephone base You may also reset by unplugging the power from the telephone base and plug it back in You cannot de register the handset s if any phone connected to your phone line is in use You will need to the reset the system clock after de registering handset s please refer to the Day amp tim
18. eipt and original packaging in case it is necessary to ship your telephone for warranty service Check to make sure the telephone package includes the following items Charger for cordless User s manual Cordless handset handset T wv Battery for cordless handset Battery compartment cover Power adapter Belt clip for cordless handset User s manual TL77008 5 8 GHz expansion handset for use with AT amp T models TL74108 TL74208 TL74308 TL74408 TL74258 TL74358 TL74458 Table of contents Getting started Quick reference guide Installation preparation Charger installation Battery installation amp CRAGIN iia Adding and registering handSetsS so s00001000000000010020 Replacing a handset Belt clip amp optional N ACSET enneccccccreseseeeeesttsseeeeee Appendix Troubleshooting 12 Maintenance siisii 22 Important safety INFOMATION eeeeeeseeeeeeees 23 FCC Part 68 and ACTA 27 FCC Part U5 cssccsstescssesasecensstcsancs 30 Limited warranty s s s 32 Technical specifications 36 Getting started Quick reference guide CHARGE On when the handset is charging in the charger CID Press to display caller ID information PHONE FLASH Press to make or answer a call During a call press to receive an incoming call if call waiting is activated REDIAL PAUSE Press to view redial memory While enteri
19. less handset and telephone base to reset Other electronic products can cause interference with your cordless phone Try installing your phone as far away from these types of electronic devices as possible television sets VCRs or other cordless telephones The batteries will not hold a charge If the cordless handset is in its telephone base or charger and the charge light does not come on refer to The charge light is off in this Troubleshooting guide Charge the battery in the cordless handset for at least 16 hours For optimum daily performance return the cordless handset to its base when not in use You may need to purchase a new battery please refer to the Battery installation and charging section of this user s manual Your phone might be malfunctioning Please refer to the Limited warranty section of this user s manual for further instruction 15 Appendix Troubleshooting get noise e If you subscribe to high speed internet static or weak service Digital Subscriber Line DSL signal even through your telephone line you must when I m near install a DSL filter between the telephone the telephone base and the telephone wall jack The filter base will prevent noise and caller ID problems caused by DSL interference Please contact your DSL service provider for more information about DSL filters e You may be able to improve the performance of your cordless phone by installing your new telepho
20. ne base as far as possible from any other existing cordless telephone system that may already be installed e Other electronic products can cause interference to your cordless phone Try installing your phone as far away from the following electronic devices as possible television sets VCRs or other cordless telephones e Do not install this phone near a microwave oven or on the same electrical outlet You may experience decreased performance while the microwave oven is operating e If your phone is plugged in with a modem or a surge protector plug the phone or modem surge protector into a different location If this solves the problem re locate your phone or modem farther apart from one another or use a different surge protector 16 Appendix Troubleshooting e Relocate your phone to a higher location The phone will likely have better reception when not installed in a low area If the other phones in your home are having the same problem the problem is in your wiring or local service Contact your local telephone company charges may apply hear other calls while using my phone Disconnect the telephone base from the telephone jack and plug in a different telephone If you still hear other calls the problem is probably in your wiring or local service Call your local telephone company My cordless handset does not ring when receive a call Make sure that the ringer is not turned off
21. ng numbers press and hold to insert a dialing pause MUTE REMOVE During a call press to mute microphone While reviewing the caller ID history press to delete an individual entry or press and hold to clear the caller ID history While predialing press to delete digits SPEAKER Press to turn on the handset speakerphone Press again to resume normal handset use CID DIR O K Q Flg oh a M 1 ABC 2 3y CM ay cy Ave u8 cr oY Orgy A d MUTE REDIAL INT j J REMOVE PAUSE SPEAKER Press or to scroll up or down while in menus While entering names or numbers press or to move the cursor to the left or right MENU SELECT Press to enter the menu While in the menu press to select an item or save an entry or setting DIR Press to display directory entries i amp E VOLUME WA a A 0 Press on the side of the handset to adjust listening volume Each press of the button increases or decreases the volume OFF CLEAR During a call press to hang up While using menus press to cancel an operation back up to the previous menu or exit the menu display INT Press to begin an intercom conversation or to transfer a call Getting started Quick reference guide Feature menu Feature menu DIRECTORY ihe DIRECTORY CALL LOG symbol CALL LOG shows a RINGER VOLUME highlighted RINGER TONE menu item KEY TONE LANGUAGE CLR VO
22. ols and features may save you a service call Except as provided by applicable law you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the PRODUCT s to the service location The manufacturer will return repaired or replaced PRODUCT under this limited warranty to you transportation delivery or handling charges prepaid The manufacturer assumes no risk for damage or loss of the PRODUCT in transit If the PRODUCT failure is not covered by this limited warranty or proof of purchase does not meet the terms of this limited warranty the manufacturer will notify you and will request that you authorize the cost of repair prior to any further repair activity You must pay for the cost of repair and return shipping costs for the repair of products that are not covered by this limited warranty 6 What must you return with the PRODUCT to get warranty service You must a Return the entire original package and contents including the PRODUCT to the service location along with a description of the malfunction or difficulty and b Include valid proof of purchase sales receipt identifying the PRODUCT purchased PRODUCT model and the date of purchase or receipt and c Provide your name complete and correct mailing address and telephone number 34 Appendix Limited warranty 7 Other limitations This warranty is the complete and excl
23. oroughly Install this product in a protected location where no one can trip over any line or power cords Protect cords from damage or abrasion If this product does not operate normally see the Troubleshooting section on pages 12 21 of this user s manual If you cannot solve the problem or if the product is damaged refer to the Limited warranty on pages 32 35 Do not open this product except as may be directed in your user s manual Opening the product or reassembling it incorrectly may expose you to hazardous voltages or other risks 23 Appendix Important safety information Replace batteries only as described in your user s manual Do not burn or puncture batteries they contain caustic chemicals This power adapter is intended to be correctly oriented in a vertical or floor mount position The prongs are not designed to hold the plug in place if it is plugged into a ceiling or an under the table cabinet outlet A caution Use only the power adapter provided with this product To obtain a replacement visit our website at www telephones att com or call 1 800 222 3111 in Canada dial 1 866 288 4268 Especially about cordless telephones Privacy The same features that make a cordless telephone convenient create some limitations Telephone calls are trans mitted between the telephone base and the handset by radio waves so there is a possibility that your cordless telephone conversations could be intercepte
24. rned or punctured they could release caustic material which could cause injury CY The RBRC Seal means that the manufacturer is voluntarily participating S in an industry program to collect and recycle Nickel metal hydride C rechargeable batteries when taken out of service within the United O WIE States These batteries may be taken to a participating local retailer of 0 397 2 replacement batteries or recycling center Or you may call 1 800 8 BATTERY for locations accepting spent Ni MH batteries Precautions for users of implanted cardiac pacemakers Cardiac pacemakers applies only to digital cordless telephones Wireless Technology Research LLC WTR an independent re search entity led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers Supported by the U S Food and Drug Administration WTR recommends to physicians that 25 Appendix Important safety information PACEMAKER PATIENTS e Should keep wireless telephones at least six inches from the pacemaker Should NOT place wireless telephones directly over the pace maker such as in a breast pocket when it is turned ON e Should use the wireless telephone at the ear opposite the pacemaker WTR s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones SAVE THESE INSTRUCTIONS 26 Appendix FCC Part 68 and ACTA This
25. rs please Remain on the line and briefly explain the reason for the call before hanging up Perform such activities in off peak hours such as early morning or late evening 28 Appendix FCC Part 68 and ACTA Industry Canada Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference including interference that may cause undesired operation The term IC before the certification registration number only signifies that the Industry Canada technical specifications were met The Ringer Equivalence Number REN for this terminal equipment is 0 1 The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five This product meets the applicable Industry Canada technical specifications 29 Appendix FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission FCC rules These requirements are intended to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance
26. s of any kind Remember that electrical appliances can cause serious injury if used when you are wet or standing in water If the telephone base should fall into water DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL Then pull the unit out by the unplugged cords 22 Appendix Important safety information A This symbol is to alert you to important operating or servicing instructions that may appear in this user s manual Always follow basic safety precautions when using this product to reduce the risk of injury fire or electric shock Safety information Read and understand all instructions in the user s manual Observe all markings on the product Avoid using a telephone during a thunderstorm There may be a slight chance of electric shock from lightning Do not use a telephone in the vicinity of a gas leak If you suspect a gas leak report it immediately but use a telephone away from the area where gas is leaking If this product is a cordless model make sure the telephone base is also away from the area Do not use this product near water or when you are wet For example do not use it in a wet basement or shower or next to a swimming pool bathtub kitchen sink or laundry tub Do not use liquids or aerosol sprays for cleaning If the product comes in contact with any liquids unplug any line or power cord immediately Do not plug the product back in until it has dried th
27. sion may not apply to you Please retain your original sales receipt as proof of purchase 35 Index Technical specifications RF frequency band handset to telephone base 2400 MHz 2483 5 MHz RF frequency band telephone base to handset 5725 MHz 5850 MHz Channels 95 Operating temperature 32 F 122 F 0 C 50 C Telephone base voltage 96 130 Vrms AC voltage 60Hz Telephone base voltage AC adapter output 9VDC 400mA Handset voltage 3 2 4 7 VDC 550mAh Charger voltage AC adapter output 9VDC 200mA Replacement battery 3 6V 600mMAH 5 8 GHz digital spread spectrum frequency hopping technology This technology digitally transmits your voice across multiple channels in both the 5 8GHz and 2 4GHz frequencies to provide enhanced range ultimate sound clarity and advanced privacy against eavesdropping on your calls while not interfering with wireless routers Telephone operating range This cordless telephone operates within the maximum power allowed by the Federal Communications Commission FCC Even so this handset and telephone base can communicate over only a certain distance which can vary with the locations of the telephone base and handset the weather and the construction of your home or office 36 atat Q www telephones att com 2008 Advanced American Telephones All rights reserved AT amp T and the AT amp
28. suse accident shipping or other physical damage improper installation abnormal operation or handling neglect inundation fire water or other liquid intrusion or e PRODUCT that has been damaged due to repair alteration or modification by anyone other than an authorized service representative of the manufacturer or e PRODUCT to the extent that the problem experienced is caused by signal conditions network reliability or cable or antenna systems or e PRODUCT to the extent that the problem is caused by use with non AT amp T accessories or e PRODUCT whose warranty quality stickers PRODUCT serial number plates or electronic serial numbers have been removed altered or rendered illegible or e PRODUCT purchased used serviced or shipped for repair from outside the United States of America or Canada or used for commercial or institutional purposes including but not limited to products used for rental purposes or 33 Appendix Limited warranty e PRODUCT returned without valid proof of purchase see item 6 below or e Charges for installation or setup adjustment of customer controls and installation or repair of systems outside the unit 5 How do you get warranty service To obtain warranty service in the United States of America visit www telephones att com or call 1 800 222 3111 In Canada call 1 866 288 4268 NOTE Before calling for service please review the user s manual a check of the PRODUCT contr
29. t has been tested and found to comply with the FCC criteria The handset may be safely held against the ear of the user The telephone base shall be installed and used such that parts of the user s body other than the hands are maintained at a distance of approximately 20 cm 8 inches or more If you choose to use a clipping device please make sure to only use the supplied AT amp T belt clip This Class B digital apparatus complies with Canadian ICES 003 31 Appendix Limited warranty The AT amp T brand is used under license any repair replacement or warranty service and all questions about this product should be directed to In the United States of America visit www telephones att com or call 1 800 222 3111 In Canada call 1 866 288 4268 1 What does this limited warranty cover The manufacturer of this AT amp T branded product warrants to the holder of a valid proof of purchase CONSUMER or you that the product and all accessories provided in the sales package PRODUCT are free from defects in material and workmanship pursuant to the following terms and conditions when installed and used normally and in accordance with the PRODUCT operating instructions This limited warranty extends only to the CONSUMER for products purchased and used in the United States of America and Canada 2 What will be done if the PRODUCT is not free from defects in materials and workmanship during the limited warranty period
30. urs For optimum daily performance return the cordless handset to its base when not in use Reset the telephone base Unplug the unit s electrical power Wait for approximately 15 seconds then plug it back in Allow up to one minute for the cordless handset and telephone base to reset You may need to purchase a new battery please refer to page 6 of this user s manual cannot get a dial tone First try all the suggestions above Move the cordless handset closer to the telephone base You might have moved out of range 12 Appendix Troubleshooting If the previous suggestions don t work disconnect the telephone base from the telephone jack and connect to a different phone If there is no dial tone on that phone either the problem is in your wiring or local service Contact your local telephone company Your line cord might be malfunctioning Try installing a new line cord cannot dial out First try all the suggestions above Make sure you have a dial tone before dialing The cordless handset may take a second or two to find the telephone base and produce a dial tone This is normal Wait an extra second before dialing Eliminate any background noise Noise from a television radio or other appliances may cause the phone to not dial out properly If you cannot eliminate the background noise first try muting the cordless handset before dialing or dialing from another room in your home
31. usive agreement between you and the manufacturer of this AT amp T branded PRODUCT It supersedes all other written or oral communications related to this PRODUCT The manufacturer provides no other warranties for this PRODUCT The warranty exclusively describes all of the manufacturer s responsibilities regarding the PRODUCT There are no other express warranties No one is authorized to make modifications to this limited warranty and you should not rely on any such modification State Provincial Law rights This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province Limitations Implied warranties including those of fitness for a particular purpose and merchantability an unwritten warranty that the PRODUCT is fit for ordinary use are limited to one year from date of purchase Some states provinces do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you In no event shall the manufacturer be liable for any indirect special incidental consequential or similar damages including but not limited to lost profits or revenue inability to use the PRODUCT or other associated equipment the cost of substitute equipment and claims by third parties resulting from the use of this PRODUCT Some states provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclu
32. utting the cordless handset in its base If it does not seem to respond do the following in the order listed Disconnect the power to the telephone base Disconnect the cordless handset battery and spare battery if applicable Wait a few minutes Connect power to the telephone base Re install the battery and place the cordless handset into the telephone base Wait for the cordless handset to re establish its connection with the telephone base Allow up to one minute for this to take place 21 Appendix Maintenance Taking care of your telephone e Your cordless telephone contains sophisticated electronic parts so it must be treated with care e Avoid rough treatment e Place the handset down gently Save the original packing materi als to protect your telephone if you ever need to ship it Avoid water e Your telephone can be damaged if it gets wet Do not use the handset outdoors in the rain or handle it with wet hands Do not install the telephone base near a sink bathtub or shower Electrical storms e Electrical storms can sometimes cause power surges harmful to electronic equipment For your own safety take caution when using electric appliances during storms Cleaning your telephone e Your telephone has a durable plastic casing that should retain its luster for many years Clean it only with a soft cloth slightly dampened with water or a mild soap e Do not use excess water or cleaning solvent
Download Pdf Manuals
Related Search