ASUS UN42 User's Manual
Contents
1. E9955 Revised Edition V2 December 2014 VivoMini memory wireless card and solid state drive SSD installation guide Your VivoMini comes with the following items Please contact ASUS Service Center if you cannot find the following items 4 pcs holed rubber foot 3 pcs 3mm round screws 1 hexagon screw IMPORTANT It is recommended that you install or upgrade the memory modules wireless card and solid state drive SSD under professional supervision Visit an ASUS service center for further assistance Ensure that your hands are dry before proceeding with the rest of the installation process Before installing any of the features in this guide use a grounded wrist strap or touch a safely grounded object or metal object to avoid damaging them due to static electricity Installing or upgrading memory modules Your VivoMini comes with two SO DIMM memory slots that allow you to install two 2GB 4GB or 8GB unbuffered with non ECC 1 35 V DDR3 204 pin SO DIMMs for a maximum of 16GB memory IMPORTANT Refer to http www asus com for the list of compatible DIMMs You can only install 1 35 V DDR3 SO DIMM to the VivoMini s DIMM slots To install or upgrade the memory modules 1 Turn off your VivoMini then disconnect all cables and peripherals 2 Place the VivoMini on a flat stable surface with its top side facing down AAAA Remove the four screws securing the cover 3 Get one screw from the ones you previously remo2. TA SSD into its the upper slot inside the VivoMini Refer to the illustration for its location 3 Gently push down the mSATA SSD on top of the screw hole and fasten it using one of the 3mm round screw Refer to the illustration for the location of the screw hole 4 Follow steps 7 9 on pages 3 4 under the nstalling or upgrading memory modules section of this guide to replace the bottom cover back on your VivoMini To install or upgrade a half size mSATA SSD iP Follow steps 1 5 on pages 1 2 under the nstalling or upgrading memory modules section of this guide to remove the bottom cover of your VivoMini 2 gt Insert the hexagon screw into its corresponding hole as illustrated Align and insert the half size mSATA SSD into its upper slot inside the VivoMini Refer to the illustration for its location Gently push down the mSATA SSD on top of the screw hole and fasten it using one of the 3mm round screw Refer to the illustration for the location of the screw hole Follow steps 7 9 on pages 3 4 under the Installing or upgrading memory modules section of this guide to replace the bottom cover back on your VivoMini
3. or a straightened paper clip to do so Installing or upgrading the wireless card Your VivoMini includes a mini PCle slot for half size wireless and Bluetooth adapters Refer to http www asus com for the list of compatible wireless and Bluetooth adapters To install or upgrade the wireless card 1 Follow steps 1 5 on pages 1 2 under the Installing or upgrading memory modules section of this guide to remove the bottom cover of your VivoMini 2 Align and insert the wireless card into the lower slot inside the VivoMini Refer to the illustration for its location 3 Gently push down the wireless card on top of the screw holes and fasten it using two of the 3mm round screws 4 Connect the black antenna to MAIN or and the white antenna to AUX or A Refer to the illustration for the right installation procedure NOTE A soft clicking sound indicates that the antenna has been securely attached on the wireless card 5 Follow steps 7 9 on pages 3 4 under the Installing or upgrading memory modules section of this guide to replace the bottom cover back on your VivoMini Installing or upgrading the mSATA SSD Your VivoMini includes a PCle slot that supports a full size or a half size mSATA SSD To install or upgrade a full size mSATA SSD i Follow steps 1 5 on pages 1 2 under the Installing or upgrading memory modules section of this guide to remove the bottom cover of your VivoMini 2 Align and insert the full size mSA
4. ved then place it into the hole Leave a portion of the screw head that would be enough for you to hold 4 Hold the screw then gently pull out the cover from the bottom side of the VivoMini Use your other free hand to hold the VivoMini in place 5 6 Align and insert the memory module into the slot A and press it down B until it is securely seated in place Repeat the same steps to install the other memory module IMPORTANT Always install into the lower slot first 8 Place the cover back on the bottom side of your VivoMini Note that the cover can only be inserted in one direction Refer to the following illustration and note to ensure that the cover is securely fitted on the bottom side of the VivoMini IMPORTANT The rating label area A and the power button s location B must be oriented as shown 9 Reattach the screws to secure the cover back on the bottom side of the main box 10 Place the rubber foot on each screw hole Refer to the illustration for more details IMPORTANT A number is printed under each rubber foot and this number corresponds to that rubber foot s location on the cover Follow the orientation of each rubber foot and the number sequence shown in the illustration below The rubber foot fits in only one orientation Note the position of the hole on each rubber foot as shown in the illustration below NOTE If you want to remove the rubber foot use a flathead screwdriver
Download Pdf Manuals
Related Search