Ariston HBK 9 LS X User's Manual
Contents
1. following simple checks before calling Technical Service e hood is not working Check that The power has not been disconnected A speed has been selected hood performs inefficiently Check that The motor speed selected is sufficient for the amount of smoke and vapours released The kitchen is sufficiently ventilated to allow air intake The charcoal filter is not worn hood in filtering version e hood has turned off during normal functioning Check that The power has not been disconnected the omnipolar disconnection device has not tripped If the hood fails to operate correctly briefly disconnect it from the mains power supply for almost 5 sec by pulling out the plug Then plug it in again and try once more before contacting the Technical Assistance Service TECHNICAL DATA Model HKB 9 LS X Height Ducting version 63 116 5 cm Height Filter version 71 7 116 5 cm Width 89 8 cm Depth 47 8 cm Gross weight 26 4 Kg Total absorption 320 W Motor absorption 1x315 W Lamp absorption 2x3 W Exhaust pipe 15 cm This appliance conforms to the following EEC Directive Low Voltage Equipment Directive 2006 95 EC 12 12 2006 Electromagnetic Compatibility Directive 2004 108 EC 15 12 2004 Components not provided with the product 172. key ON Automatic mode OFF Manual mode Automatic operating mode COOKING The system is set by default to the manual operating mode to activate the automatic operating mode press key T5 With hood off LEDs L1 L4 switch on With hood on the LED of the speed selected switches on while the other LEDs start flashing During cooking the system promptly reacts to Vapour Gas increases it switches the hood on at the most suitable speed and keeps working at the same speed for at least 1 minute before getting back to the lowest speed switching off When cooking is over and the environmental parameters are back on the levels prior to cooking the system switches off Note If the parameters are close to the rest condition the system forces the hood switching off after 30 minutes It is possible to deactivate the automatic operating mode as follows Press key T5 and the motor gets back to the manual operating mode Note it is also possible to get back to the manual operating mode by pressing keys T2 or the system decreases T2 increases T3 the motor speed or switches 6 the hood off T6 ON OFF Suction motor With hood on at any speed press key T6 and the hood switches off With hood off press key T6 and the hood switches on at Speed 1 Selection of the hob This operation is necessary to optimize the automatic functioning of the hood according to the type of hob selected Note The hob set by def
3. A ARISTON Betriebsanleitung AUT Instructions for use m OR o Istruzioni per l uso pk ederlands Mode d emploi mi N Instrucciones de uso Gebruiksaanwijzingen Instrucoes de uso HKB 9 LS X no 2x 3 5x9 5 E 2X 2 9x6 5 ARISTON a gt 65 gt 50 A ARISTON A ARISTON A ARISTON English The hood can look different to that illustrated in the drawings in this booklet The instructions for use maintenance and installation however remain the same important to conserve this booklet for consultation at any moment In the case of sale cession or move make sure it is together with the product Read the instructions carefully there is important information about installation use and safety Do not carry out electrical or mechanical variations on the product or on the discharge conduits GENERAL SAFETY The minimum distance between the supporting surface for the cooking equipment on the hob and the lowest part of the range hood must be not less than 50cm from electric cookers and 65cm from gas or mixed cookers If the instructions for installation for the gas hob specify a greater distance this must be adhered to Expansion wall plugs are provided to secure the hood to most types of walls ceilings However a qualified technician must verify suitability of the materials in accordance with the ty
4. Speed decrease Press key T2 to decrease the speed from 4 intensive to 1 Press key T2 during operation at speed 1 the hood moves to OFF state T3 Speed increase Press button T3 and the hood moves to OFF state at speed 1 Press the button hood in ON state to increase the motor speed from 1 to the intensive speed timed Speed 1 LED L1 Speed 2 LED L1 L2 Speed 3 LED L1 L2 L3 Intensive speed timed LED L1 L2 L3 L4 flashing Note Speed 4 intensive timed keeps on for 5 minutes after that the hood sets speed 2 automatically T4 Speed timing Filter saturation signal control and configuration Speed timing The speed timing is activated by pressing key T4 when the timing has elapsed the hood switches off The timing is divided as follows Speed 1 20 minutes LED L1 flashing Speed 2 15 minutes LED L1 L2 flashing Speed 3 10 minutes LED L1 L2 L3 flashing Intensive Speed 5 minutes LED L1 L2 L3 L4 flashing During the timed operation press key T2 and the hood quits the timed mode and decreases the speed Press key T3 and the hood quits the timed mode and increases the speed Press key T4 and the hood quits the timed mode keeping the speed set Filter saturation signal control and configuration Grease filter signal After 80 working hours LED L1 flashes When such signal appears carry out the maintenance of the grease filter To reset the signal with hood on keep key T4 pressed for 5 The hood gives out a and th
5. al calibration after a long period of non use after a blackout or when there is a very quick change in temperature in the kitchen The calibration can be carried out manually Set the hood to OFF When keys T6 and T5 are pressed contemporaneously for 5 LEDs L1 and L4 start flashing for a period of time that can vary according to the hob selected however no longer than fifteen minutes 15 Sensor test The sensors are tested constantly during the automatic operation In the case of failure the display shows all flashing LEDs contact the technical service The hood can be used in manual mode anyway MAINTENANCE ATTENTION Before performing any maintenance operation isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse Or if the appliance has been connected through a plug and socket then the plug must be removed from the socket Cleaning The cooker hood should be cleaned regularly at least with the same frequency with which you carry out maintenance of the fat filters internally and externally Clean using the cloth dampened with neutral liquid detergent Do not use abrasive products DO NOT USE ALCOHOL WARNING Failure to carry out the basic cleaning recommendations of the cooker hood and replacement of the filters may cause fire risks Therefore we recommend oserving these instructions The manufacturer declines all responsibility for any damage to the m
6. any other purpose such as discharging exhaust fumes from appliances burning gas or other fuels The flaming of foods beneath the hood itself is severely prohibited The use of exposed flames is detrimental to the filters and may cause a fire risk and must therefore be avoided in all circumstances Any frying must be done with care in order to make sure that the oil does not overheat and ignite Accessible parts of the hood may became hot when used with cooking applicance With regards to the technical and safety measures to be adopted for fume discharging it is important to closely follow the regulations provided by the local authorities The hood must be regularly cleaned on both the inside and outside AT LEAST ONCE A MONTH This must be completed in accordance with the maintenance instructions provided in this manual Failure to follow the instructions provided in this user guide regarding the cleaning of the hood and filters will lead to the risk of fires Do not use or leave the hood without the lamp correctly mounted due to the possible risk of electric shocks We will not accept any responsibility for any faults damage or fires caused to the appliance as a result of the non observance of the instructions included in this manual 14 ELECTRICAL CONNECTION The mains power supply must correspond to the rating indicated on the plate situated inside the hood If provided with a plug connect the hood to a socket in compliance with cu
7. ault is the Gas hob To select a different hob or to check the hob set follow the instructions below Set the hood to OFF Press keys T2 and T3 contemporaneously for about 5 seconds until the hob being used is displayed the hood gives out a BEEP signal Gas hob LED L1 on Induction hob LED L2 on Electric hob LED L3 on The cyclical selection of the hob is possible by pressing keys T2 or Once the hob has been selected wait for 10 to accept the function The acceptance of the hob selected is displayed by the sequence of 3 flashes of the relevant LED of the hob selected After selecting the hob it is necessary to carry out the Sensor calibration again Sensor calibration Automatic or Manual In order that the sensor responds correctly to the thermal stresses produced by the hob below it is necessary to calibrate the sensor Note before calibrating the sensor carry out the Selection of the hob see previous paragraph Note Carry out the calibration when installing the hood for the first time after a long period of non use or a blackout The calibration must be carried out with motor off Automatic calibration of the sensor The automatic calibration of the sensor starts as soon as the hood is fed visible by pressing key T5 LEDs L1 L4 flash for a period of time that can vary according to the hob selected however no longer than fifteen minutes Manual calibration of the sensor Note Carry out the manu
8. en it switches off LED L1 stops flashing Charcoal filter signal After 320 working hours LED L2 flashes When such signal appears carry out the maintenance of the charcoal filter To reset the signal with hood on keep key T4 pressed for 5 The hood gives out a and then it switches off LED 12 stops flashing In the case of contemporaneous signaling of both filters LEDs L1 and L2 flash The signal is reset by carrying out the procedure described above 2 times The first time it resets the charcoal filter signal the second time it resets the grease filter signal Note In the standard mode the charcoal filter signal is not active When the hood is used in filter version activate the charcoal filter signal Activating charcoal filter signal Set the hood to OFF and keep key T4 pressed for 5 As soon as the key is pressed the relevant LEDs of the signals of the filters currently active will light up Keep pressing the hood will give out a BEEP and LED L2 will flash for 2 LEDs L1 and L2 remain on for about 2 before the hood gets back to OFF state Deactivating charcoal filter signal Set the hood to OFF and keep key T4 pressed for 5 As soon as the key is pressed the relevant LEDs of the signals of the filters currently active will light up Keep pressing the hood will give out a BEEP and LED L2 will switch off LED L1 remains on for about 2 before the hood gets back to OFF state T5 Sensor control
9. otor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations Perimeter aspiration panel Clean the perimeter aspiration panel with the same frequency as the ant fats filter using a cloth and not too concentrated liquid detergent Do not use abrasive substances Maintenance of the anti grease filters Traps cooking grease particles This must be cleaned once a month or when the filter saturation indication system if envisaged on the model in possession indicates this necessity using non aggressive detergents either by hand or in the dishwasher which must be set to a low temperature and a short cycle When washed in a dishwasher the grease filter may discolour slightly but this does not affect its filtering capacity To remove the grease filter pull the spring release handle 16 Maintenance of the charcoal filter It absorbs unpleasant odours caused by cooking The saturation of the charcoal filter occurs after more or less prolonged use depending on the type of cooking and the regularity of cleaning of the grease filter In any case it is necessary to replace the cartridge at least every four mounths or when the filter saturation indication system if envisaged on the model in possession indicates this necessity The charcoal filter may NOT be washed or regenerated Assembly Hook the charcoal filter at the back on the metal tongue of the hood first then on the f
10. our cooker hood is ready to be used in suction version To use the hood in filtering version the special ACCESSORY KIT must be installed Check on the first pages of this manual if the ACCESSORY KIT is furnished or must be bought separately Note If furnished in certain cases the additional activated carbon filtering system may be installed on the hood Information about the conversion of the hood from suction version to filtering version is present in this manual Ducting version In this case the fumes are conveyed outside of the building by means of a special pipe connected with the connection ring located on top of the hood Attention The exhausting pipe is not supplied and must be purchased apart Diameter of the exhausting pipe must be equal to that of the connection ring In the horizontal runs the exhausting pipe must be slightly slanted about 10 and directed upwards to vent the air easily from the room to the outside Attention If the hood is supplied with active charcoal filter then it must be removed gt Filter version One active charcoal filter is needed for this and can be obtained from your usual retailer The filter removes the grease and smells from the extracted air before sending it back into the room through the upper outlet grid A ARISTON CONTROLS To select the functions of the hood just touch the commands L2 L4 L1 T 5 0 1 ecc O S T6 T1 T2 T3 T4 T5 T1 ON OFF Lights T2
11. pe of wall ceiling The must be strong enough to take the weight of the hood Do not tile grout or silicone this appliance to the wall Surface mounting only WARNING Do not connect the appliance to the mains until the installation is fully complete Before any cleaning or maintenance operation disconnect hood from the mains by removing the plug or disconnecting the mains electrical supply Always wear work gloves for all installation and maintenance operations The appliance is not intended for use by children or persons with impaired physical sensorial or mental faculties or if lacking in experience or knowledge unless they are under supervision or have been trained in the use of the appliance by a person responsible for their safety This appliance is designed to be operated by adults children should be monitored to ensure that they do not play with the appliance This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the appliance Never use the hood without effectively mounted grating The hood must NEVER be used as a support surface unless specifically indicated The premises where the appliance is installed must be sufficiently ventilated when the kitchen hood is used together with other gas combustion devices or other fuels The ducting system for this appliance must not be connected to any existing ventilation system which is being used for
12. ront with the two knobs Disassembly Remove the charcoal filter by turning the knobs fixing it to the hood by 90 Replacing lamps The hood is equipped with a lighting system based on LED technology The LEDs guarantee an optimum lighting a duration up to 10 times as long as the traditional lamps and allow to save 90 electrical energy For replacement contact the technical service A ARISTON DISPOSAL This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol mw on the product on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For further detailed information regarding the process collection and recycling of this product please contact the appropriate department of your local authorities or the local department for household waste or the shop where you purchased this product MALFUNCTIONS If something appears not to be working properly do the
13. rrent regulations and positioned in an accessible area after installation If it not fitted with a plug direct mains connection or if the plug is not located in an accessible area after installation apply a double pole switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over current category Ill in accordance with installation instructions Warning Before re connecting the hood circuit to the mains supply and checking the efficient function always check that the mains cable is correctly assembled Replacing the power cable The hood is provided with a special power cable if the cable is damaged request a new one from Technical Service AIR VENT for the suction versions Connect the hood and discharge holes on the walls with a diameter equivalent to the air outlet connection flange Using the tubes and discharge holes on walls with smaller dimensions will cause a diminution of the suction performance and a drastic increase in noise Any responsibility in the matter is therefore declined Use a duct of the minimum indispensible length Use a duct with as few elbows as possible maximum elbow angle 90 Avoid drastic changes in the duct cross section Use a duct with an as smooth as possible inside The duct must be made of certified material The company declines any responsibility whenever these regulations are not respected FILTERING OR DUCTING Y
Download Pdf Manuals
Related Search