Apple Power Mac 073-0584 User's Manual
Contents
1. Power Mac G4 Cube Power Button Gasket Replacement Instructions Be sure to follow the instructions in this sheet carefully Failure to follow these instructions could result in damage to your equipment and may void your warranty Replacing your power button gasket requires five basic steps Turn off the computer Remove the computer core from the enclosure Remove the installed gasket e Install the replacement gasket e Replace the computer core in the enclosure Note Written and video instructions covering customer installable parts are available at http Awww info apple com installparts Tools Required No tools are required for this procedure Electrostatic Discharge ESD Static electricity anormal and natural phenomenon builds up on your body as you walk around You experience an electrostatic discharge ESD when you touch an object and feel a spark ESD can cause damage to the internal components of your computer To avoid ESD damage read and follow all instructions 073 0584 Rev B Removing the Computer Core From the Enclosure Warning Always turn off your computer before opening it to avoid damaging its internal components 1 Place your computer on a clean flat surface 2 Shut down your computer by opening the Special menu and choosing Shut Down Then wait five minutes for the computer s internal components to cool down 3 Unplug all cables from the computer except the power cord N2. document is accurate Apple is not responsible for printing or clerical errors Apple Computer Inc 1 Infinite Loop Cupertino CA 95014 2084 408 996 1010 http Awww apple com Apple the Apple logo Mac Macintosh and the Mac logo are trademarks of Apple Computer Inc registered in the U S and other countries Power Mac is a trademark of Apple Computer Inc Power Mac G4 Cube Power Button Gasket 6
3. asket Replacing the Computer Core in the Enclosure 1 Holding the core by the latch insert the core into the enclosure Note The core fits into the enclosure only one way Position the core so the ports are toward the back of the enclosure Core Enclosure 2 With a flat hand press down on the latch until it locks into place Firmly press the core to ensure it is fully secured within the enclosure Important Do not lift or carry your computer by the core latch The enclosure could fall off the core and be damaged Power Mac G4 Cube Power Button Gasket 5 3 Turn your computer upright and reconnect all cables 4 Restart your computer Warning Never turn on your computer unless all of its internal and external parts are in place and it is closed Operating the computer when it is open or missing parts can damage your computer or cause injury Apple Computer Inc 2001 Apple Computer Inc All rights reserved Under the copyright laws this document may not be copied in whole or in part without the written consent of Apple The Apple logo is a trademark of Apple Computer Inc registered in the U S and other countries Use of the keyboard Apple logo Option Shift K for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal and state laws Every effort has been made to ensure that the information in this
4. ote If you have never plugged in your computer connect the computer s power cord and plug it in 4 Turn the computer on its side on a soft clean cloth and ground yourself by touching the bare metal between the video ports Important To avoid electrostatic discharge always ground yourself by touching the bare metal before you touch any parts or install any components inside the computer To avoid static electricity building back up in your body do not walk around the room until you have completed the installation and closed the computer 5 Unplug the power cord 2 Power Mac G4 Cube Power Button Gasket 6 Turn the computer upside down and push down on the latch to release it Allow the latch to extend completely Latch Extended Latch 7 Gently pull the core from the computer enclosure and place the core on a soft cloth Enclosure Power Mac G4 Cube Power Button Gasket 3 Removing the Power Button Gasket The power button gasket is a small flexible gray ring Place your hand in the computer enclosure and lift out the installed gasket Gasket Enclosure Installing the New Power Button Gasket 1 Insert the new power button gasket into the recessed area that encircles the power button 2 Press the gasket into place to ensure that it is secure 3 Install the computer core back into the enclosure as described in the next section 4 Power Mac G4 Cube Power Button G
Download Pdf Manuals
Related Search