Home

American Standard 7236E User's Manual

image

Contents

1. AND SPAN IS A REGISTERED TRADEMARK OF PROCTER amp GAMBLE ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes WARNING When using electrical products basic precautions should always be observed including the following 1 DANGER RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a ground fault circuit interrupter 2 Grounding is required The unit should be installed by a licensed electrician and grounded 3 Install to permit access for servicing 4 All building materials and wiring should be routed away from the pump body and heater if equipped The whirlpool should be installed on a 120 vac 20 amp dedicated circuit The circuit should be hard wired from the electrical power supply panel The circuit must be a three 3 wire circuit from the electrical supply panel A grounded neutral wire and a third wire earth ground are essential ADDING THE E Z INSTALL HEATER REQUIRES A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT ELECTRICAL INSTALLATION 20 AMP GFCI OUTLET WHIRLPOOL MOUNTED 120 VAC AIR SWITCH OR WALL TIMER ELECTRICAL DIAGRAM READ AND FOLLOW ALL INSTRUCTIONS 752869 100 Rev D 3 WIRE SELECTION GUIDE Maximum distance from fusebox to motor The sizes shown on this chart are recommendations for copper conductors only Always follow local and national Motor Hi Performance Ra
2. the top of the stringer touching the traced line 3 Install drain components to the whirlpool following the manufacturers instructions Before replacing your whirlpool for final installation be certain that an opening has been provided in the sub floor for the drain See the roughing in drawing for suggested opening size and location dimensions 4 Replace whirlpool and re shim the integral support feet shimming the entire length of the support feet Secure the shims using construction adhesive silicone mortar or equivalent materials While not a necessity the use of a foundation base consisting of cement e g Sakrete mortar or grout will help provide a solid and secure installation FIG 1 1832 mm LEVELING STRINGERS TILE TILE BEAD STRIP ADHESIVE Ming LEVELING UNLESS AN ACCESS OPENING OF AT LEAST STRINGER 12 X 24 305 X 610MM IS PROVIDED WARRANTY SERVICE WILL NOT BE PERFORMED TILE N WALLBOARD TILE SEALANT BEAD STRIP BATH ADHESIVE h LEVELING STRINGER NOTE Tile bead kit not included and must be purchased separately TYPICAL PIER TYPE INSTALLATION AS DESIRED 876 mm 70 1 2 1791 mm CUTOUT MOUNTING SURFACE WATERPROOF SEALANT 24 610 mm ACCESS PANEL BATH UNLESS AN ACCESS OPENING OF AT LEAST 12 X 24 305 X 610MM IS PROVIDED WARRANTY SERVICE WILL NOT BE PERFORMED 752869 100 Rev D SPIC
3. 7236E SERIES American Standard onciossenue WHIRLPOOL SHON EE oe enGe INSTALLATION INSTRUCTIONS 1829mm 914mm 72 Tea THANK YOU for selecting an American Standard bath Your new bath is shipped to you after careful inspection The N whirlpool version is completely assembled with pump i 914 36 70 1 2 X 34 1 OUTLINE OF CUTOUT 1791mm X 876mm Bee gu motor and system piping All you need to finish the mm mm 7x14 cuTOUT SER installation are your selected fittings and electrical 4 wed connections for a whirlpool S2o gS To insure maximum performance and pleasure from BE r as this product please follow the instructions and DRAIN i aa aad cautions 279mm 18 1 2 11 ON OFF a RECOMMENDED SWITCH Bax syamm ose Kit List of Optional Components not included ME IN LINE HEATER J e Flex Jet Pulse Jet Kit REMOVABLE BLANK w e Flex Jet Soft Jet Kit Bom e 6 Foot Apron P e E Z Install Heater T 489 i it e e Tile Bead Kit f STRINGER oe Li f Required C included 44mm FRINGE A ist of Required Components not included ca SUPPORT e Drain e Bath Filler aa Ee er ee ey ROUGH FLOOR i sonm t Kre T ae see your Home Depot Retailer a FEET 1 1 2 O D TAILPIE
4. C AND SPAN IS A REGISTERED TRADEMARK OF PROCTER amp GAMBLE
5. CE GENERAL SPECIFICATIONS FOR 7236E WHIRLPOOL List of Required Tools and Supplies INSTALLED SIZE ______ s72 x 36 x 21 1 4 In 1829 x 914 x 540mm WEIGHT w WATER oe beta na Tools Supplies S g 3 GAL TO OVERFLOW 78 Gal 296 L e Level e Nails WHIRLPOOL MIN OPERATING VOL 69 Gal 262 L e Tape Measure e Putty BATHING WELL AT SUMP ________________ 46 x 18 In 1168 x 457mm e Pipe Wrench e Caulking waterproof BATHING WELL AT RIM _________ 66 x 0 1 2 In 1676 x 775mm e 1 F H e WATER DEPTH TO OVERFLOW 15 3 4 In 400mm Slip Joint Pliers 1x 3 orexe FLOOR LOADING 42 Lbs Sq Ft 204 Kgs Sq m e Screw Driver Stringers PROJECTED AREA e Standard e Drop Cloth Pie a ao Woodworking Tools e 20 amp GFI WHIRLPOOL ELECTRICAL SPECIFICATIONS e Personal Safety Outlet PUMP 2 1 HP 14 4 AMPS 120V Equipment e Cement Plaster e Caulking Gun Grout GENERAL INSTALLATION INFORMATION Carefully uncrate and inspect your new bath for any shipping damage If such damage is found report it to your vendor immediately After inspection and during installation protect the bath from construction damage After installation and before enclosing with wallboard tile etc water test the unit and check for leaks Do not make modifications to the whirlpool system or remove pump from factory mounting This could adversely affect the safety and performance of the whirlpool and void the warranty Do not handle or move the whirlpool by the pump motor or pip
6. ing system Fittings bath filler shower arm etc are not provided with the bath and must be ordered separately Framing and enclosing materials are provided by others Check for availability of optional American Standard wall tiling bead required for recess installations Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth WARNING Do not lift whirlpool by the piping harness at any time FOR AFTER SALES SERVICE CALL 1 800 442 1902 WEEKDAYS American Standard Inc 2003 752869 100 Rev D All product names listed herein are trademarks of American Standard Inc unless otherwise noted INSTALLATION AND FRAMING INSTRUCTIONS The variety of installations possible for this whirlpool may require framing procedures other than those shown Locate studs as required Ensure roughing in dimensions are proper plumb and square Provisions must be made in all installations for an access opening for servicing the pump and controls It is strongly recommended that an additional opening be provided for access to the drain components NOTE The apron should not be used as the primary access opening 1 Position the whirlpool into the installation opening and level the deck shimming the integral support feet as necessary Mark the final position of the underside of the deck by tracing a line on to the studs see Figure 1 2 Remove the whirlpool and attach a 2 x 4 stringer to the studs with
7. ring 120V Power Line 10 8 electrical codes DRAIN CONNECTION AND SYSTEM TEST Using recommended drain opening connect whirlpool drain to waste line Tighten all drain joints securely Check the pump couplings and make sure they are hand tight Clean the whirlpool and fill with water to a point 2 above the top of the highest jet Recheck the pump couplings and make certain that they are not leaking Although the pump couplings are factory tightened and inspected some loosening may have occured during transit Make sure the whirlpool is connected to the electrical supply and turn the whirlpool on Check for leaks around all piping connections while the whirlpool is running POST INSTALLATION CLEAN UP Remove all construction debris from bath Tile grout can be removed with a wooden popsicle stick or tongue depressor Do not use wire brushes or any other metal implement on bath surface Post installation clean up generally can be completed using warm water and liquid dishwashing detergent Stubborn dirt or stains may be removed using granular Spic and Span mixed with water Painter s naphtha can be used to remove excess adhesives and or wet oil base paint HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES Abrasive cleaners must not be used since they will scratch and dull the surface Dulled areas can be restored by rubbing with a white automotive type polishing compound and waxing with a liquid wax 752869 100 Rev D 4 SPI

Download Pdf Manuals

image

Related Search

Related Contents

Genome-TALER™ Human AAVS1 Safe Harbor Gene knock  Philips Softone Candle energy saving bulb 872790082695100  

Copyright © All rights reserved.
Failed to retrieve file