American Standard Tendence 2088 User's Manual
Contents
1. handle position Flush lines and reinstall Aerator ADJUST HOT LIMIT STOP Turn on valve and allow water supply temperatures to stabilize Move HANDLE to full HOT setting Check water temperature To decrease hot limit temperature setting Replace Cartridge Cover 4 Align Handle 3 and tighten Set Screw 2 Replace Plug Button 1 CARE INSTRUCTIONS FIGURE 2B 1 1 4 CARTRIDGE Cy 4 HOTTEST Aan Blend control setting O setting insert covers blend control setting number 1 4 wily lt Gy g USA COOLEST Blend control setting 4 DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M968712 REV 1 22. Installation Instructions TENDENCE nee SINGLE LEVER LAVATORY FAUCET Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly Certified to comply with ANSI A112 18 1 please read these instructions carefully before you begin M968712 REV 1 2 TOOLS REQUIRED 3 32 Hex Key Channel Locks Plumbers Putty or Caulking FAUCET INSTALLATION Turn off For 3 hole 4 centers installation apply Putty to underside of Escutcheon 4 and place over holes in lavatory sink with tab towards back Feed faucet tubes through Rubber Ring 2 and through hole in Escutcheon 4 or mounting surface Make sure Rubber Ring 2 is seated in groove in base of Faucet 1 Escutcheon 4 is optional on single hole lavatories From below push Mounting Gasket 5 and Mounting Washer 6 over Stud 3 and secure with Nut 7 pushing Faucet 1 to back of sink so Stud 3 rests against sink hole Before final tightening adjust Faucet 1 and Escutcheon 4 so that they are centered Carefully bend and or cut supply tubes and connect left tube to HOT water and right tube to COLD water supply using appropriate connectors LAVATORY INSTALL POP UP DRAIN Push Tail piece 41 down into Trap C threaded end up Thread Locknut 5 Washer 4 and Gasket 3 Bevel side up onto Drain Body 10 Apply a bead of Putty D to unders
3. ide of Flange 2 Feed Drain Body 10 up through Sink A and thread the Flange 2 fully onto Drain Body 10 Tighten Locknut 5 firmly using channel locks keeping the pivot rod hole pointed towards the back of the sink Assemble Pivot Rod 9 as shown in Figure 2B Notice the position of the Concave Washer G Insert Pivot Rod 9 into Drain Body 10 and tighten Pivot ut F Push Tailpiece Insert 12 into Tailpiece 71 and push Tailpiece up and thread tightly into Drain Body 10 Position Extension Rod 7 onto Pop Up Rad E and tighten Thumbscrew 6 Remove one end of Clip 8 from Pivot Rod 9 by squeezing ends together while sliding Insert Pivot Rod 9 into second or third hole in Extension Rod 7 and reassemble Clip 8 Drop Stopper 1 into Drain Body 10 Adjust stopper height by repositioning Extension Rod 7 and tightening Thumbscrew 6 TEST FAUCET Remove Aerator Turn on water supplies and check for leaks Operate Handle up and down and left and right and check for proper operation Om 1 2 Goa E Pull out Plug Button 1 loosen Handle Set Screw 2 5 and remove Handle 3 from Cartridge Stem 5 Remove Cartridge Cover 4 Lift Setting Insert 6 rotate counterclockwise one notch and replace Check water temperature and repeat if necessary Unit is factory set at O full HOT water As the setting number increases the more cold water is supplied in the full HOT
Download Pdf Manuals
Related Search