American Standard MONTERREY 6540.14 User's Manual
Contents
1.2. Press TEE 6 onto SPOUT SHANK 7 making certain that the O RING 8 is properly seated on SHANK 7 Push COUPLING 9 into TEE 6 and attach to SPOUT SHANK 7 and tighten Place RUBBER RING 191 into DECK ADAPTERS 10 and thread onto valves until snug against internal stop E Tighten LOCKNUT 1 to secure VALVE 5 position E Slide FERRULE 13 and COUPLING NUT 14 to outlet of VALVE 5 and tighten COUPLING NUT 14 firmly Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector i A 10 5 16 MIN 5 1 1 ees 3 2 PUTTY Apply a bead of PUTTY around underside De of DRAIN FLANGE 1 flange Insert DRAIN PLUG 2 into SINK drain hole Hold DRAIN PLUG 2 to prevent turning and assemble GASKET 3 WASHER 4 and LOCKNUT 5 from underneath sink Apply sealant to threaded end of TAILPIECE and thread into lower end of DRAIN PLUG Connect other end to trap TEST INSTALLED FAUCET Remove AERATOR With handle in OFF position turn on water supplies and check all connections for leaks STOP 304 WASHER j To change direction of handle rotation proceed as follows SPRING m Turn valve to OFF position CLIP m Remove HANDLE and BONNET NUT m Remove SPRING CLIP SERVICE m Lift STOP WASHER turn 90 and replace m Replace SPRING CLIP m Replace BONNET NUT HANDLE SCREW
3. and INDEX AERATOR may accumulate dirt causing distorted and reduced water flow Remove AERATOR and rinse clean a SURFACE 1 lt gt D MOUNTING LEDGE Turn VALVES 1 to off position Insert ADAPTOR 8 with larger diameter over the VALVE STEM 4 Align LEVER 2 or WRIST BLADE HANDLE 3 and install onto VALVE STEM 4 Insert BLUE INDEX 5 into cold valve right side and red aa 6 into hot valve left side Insert HANDLE SCREW 7 into HANDLES and tighten with screwdriver Operate both handles to flush water lines thoroughly Check spout mounting and hose connections for leaks Turn handles into OFF position and replace AERATOR If spout drips operate handles several times from OFF to ON position Do not force handles turn only 90 Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow To clean first turn off hot and cold water supplies then m Remove HANDLE and BONNET NUT m Remove CARTRIDGE by puling up m pee rinse plastic SCR at base of CARTRIDGE Replace CARTRIDGE until flange is tight against valve body Turn valves OFF Replace BONNET NUT HANDLE SCREW and INDEX SCREEN CARTRIDGE CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M968508 REV 1 3
4. Installation Instructions 6540 140 MONTERREY 6540 170 6542 140 SPREAD LAVATORY 6542 170 6542 145 aces 6540 175 Thank you for selecting American Standard 6542 175 the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended tools SS See Screwdriver Channel Locks Adjustable Wrench spour on Base asseMely BEZNE incor Insert SPOUT SHANK 1 through center hole of mounting surface making sure RUBBER GASKET 2 is properly positioned in SPOUT BASE 3 Assemble RUBBER WASHER 4 BRASS WASHER 5 and LOCKNUT 6 onto threads of SPOUT SHANK 1 from underside of mounting surface Align SPOUT 7 and tighten LOCKNUT 6 Be sure slot in BRASS WASHER 5 is positioned to the rear as shown 1 rs TO CHANGE SPOUT TO A SWIVEL SPOUT Unscrew SPOUT NUT 8 and remove SPOUT 7 Take SPOUT CLIP 9 off SPOUT 7 and remove RUBBER RING 10 Replace RUBBER RING 10 with seperate PLASTIC RING 11 packed with faucet Put SPOUT CLIP 9 on SPOUT 7 Reassemble SPOUT 7 to SPOUT BASE 3 Certified to comply with ANSI A112 18 1M M968508 REV 1 3 C Tubing Cutter 2 VALVE ASSEMBLY Install LOCKNUTS 1 BRASS WASHERS 2 and RUBBER WASHERS 3 onto valve shanks Push TUBING 4 ends into VALVE 5 side outlets Insert VALVES 5 into mounting holes from underside of ledge
Download Pdf Manuals
Related Search