American Standard 2805.XXXW User's Manual
Contents
1. RVICE WILL NOT BE PERFORMED UNLESS AN ACCESS OPENING OF AT LEAST 12 X 24 305 X 610MM IS PROVIDED WARRANTY SERVICE WILL NOT BE PERFORMED 752294 100 Rev K 2 ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes WARNING When using electrical products basic precautions should always be observed including the following 1 DANGER RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a ground fault circuit interrupter 2 Grounding is required The unit should be installed by a licensed electrician and grounded 3 Install to permit access for servicing 4 All building materials and wiring should be routed away from the pump body and heater if equipped 1 6 HORSEPOWER MODELS The whirlpool should be installed on a 120 vac 15 amp dedicated circuit The circuit should be hard wired from the electrical power supply panel The circuit must be a three 3 wire circuit from the electrical supply panel A grounded neutral wire and a third wire earth ground are essential ADDING THE SAFE T HEATER REQUIRES A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT 2 1 HORSEPOWER MODELS The whirlpool should be installed on a 120 vac 20 amp dedicated circuit The circuit should be hard wired from the electrical power supply panel The circuit must be a three 3 wire circuit from the electrical supply panel A grounded2. Y i THREADS INTEGRAL 1 1 2 ea ail FEET TAILPIECE pal SUPPORT 4 3 4 List of Required Tools and Supplies GENERAL SPECIFICATIONS FOR 2805 WHIRLPOOL INSTALLED SIZE ____60 x 42 x 21 1 2 In 1524 x 1067 x 546mm Tools Supplies WEIGHT 130 Lbs 59 Kg i WEIGHT w WATER 689 Lbs 310 Kg Level Nails GAL TO OVERFLOW 64 Gal 243 L e Tape Measure e Putty WHIRLPOOL MIN OPERATING VOL 52 Gal 197 L e Pi e i BATHING WELL AT SUMP ___ 43 x 22 In 1092 x 559mm Pipe Wrench Caulking waterproof BATHING WELL AT RIM 55 x 35 1 2 In 1397 x 902mm e Slip Joint Pliers e 1x3or 2x2 WATER DEPTH TO OVERFLOW 15 In 381mm e Screw Driver Stringers FLOOR LOADING 39 Lbs Sq Ft 191 Kgs Sq PROJEGTEDAREAT BS pete EIS KORSE e Standard e Drop Cloth PTS 27 8 Woodworking Tools e 15 or 20 amp GFCI 47 4 e WHIRLPOOL ELECTRICAL SPECIFICATIONS Gre ao c anes Plast SYSTEM PUMP 1 6 HP 9 7 AMPS 120V quipmen Ement aster SYSTEM II PUMP 2 1 HP 15 6 AMPS 120V e Caulking Gun Grout GENERAL INSTALLATION INFORMATION Carefully uncrate and inspect your new bath for any shipping damage If such damage is found report it to your vendor immediately After inspection and during installation protect the bath from construction damage After installation and before enclosing with wallboard tile etc water test the unit and check for leaks Do not make modifications to the whirlpool system or
3. ee ee 2805 XXXW Amtricam Standard SERIES WHIRLPOOL HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS INSTALLATION INSTRUCTIONS 1524mm 60 INTEGRAL po FITTING DECK le THA NK YOU Pa A i E for selecting an American Standard bath Your new 305mm Ruse bath is shipped to you after careful inspection The 12 Be DRAIN whirlpool version is completely assembled with pump T PUMP motor and system piping All you need to finish the 1067mm TA genome installation are your selected fittings and electrical 42 _ A roor NEREA S connections for a whirlpool TO PUMP FOR A SERVICE ON ALL To insure maximum performance and pleasure from INSTALLATIONS 5 EG ee this product please follow the instructions and SWITCH Cautions lg 19mm 1 fi 3 4 ZE OF CUTOUT List of Optional Components not included 1486mm x 1029mm 58 1 2 x 40 1 2 e 5 Foot Apron Saree HEATER e Safe T Heater 9075 120 51mm 2 REMOVABLE E LEVELING STRINGER BLANK NOT FOR SUPPORT i if Ismim see your American Standard Distributor E 5 1 4 heat Xon oF List of Required Components not included 21 172 Seana e Drain 1583 470 495 i 19 112 aa e Bath Filler see your American Standard Distributor aor 1 1 2 N P T A
4. neutral wire and a third wire earth ground are essential ADDING THE SAFE T HEATER REQUIRES A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT ELECTRICAL INSTALLATION SEPARATE 15 AMP GFCI or SEPARATE 20 AMP GFCI FOR 1 6HP MODELS FOR 2 1HP MODELS 120 VAC WHIRLPOOL MOUNTED AIR or ELECTRONIC SWITCH or WALL TIMER 1 6HP MODELS ONLY ELECTRICAL DIAGRAM READ AND FOLLOW ALL INSTRUCTIONS 752294 100 Rev K 3 WIRE SELECTION GUIDE Maximum distance from fusebox to motor The sizes shown on this chart are recommendations for copper conductors only Always follow local and national electrical codes Hl Performance Rating 120V Power Line 1 6 ie DRAIN CONNECTION AND SYSTEM TEST Using recommended drain opening connect whirlpool drain to waste line Tighten all drain joints securely Check the pump couplings and make sure they are hand tight Clean the whirlpool and fill with water to a point 2 above the top of the highest jet Recheck the pump couplings and make certain that they are not leaking Although the pump couplings are factory tightened and inspected some loosening may have occurred during transit Make sure the whirlpool is connected to the electrical supply and turn the whirlpool on Check for leaks around all piping connections while the whirlpool is running POST INSTALLATION CLEAN UP Remove all construction debris from bath Tile grout can be removed with a wooden popsicle stick or tongue depressor Do not u
5. remove pump from factory mounting This could adversely affect the safety and performance of the whirlpool and void the warranty Do not handle or move the whirlpool by the pump motor or piping system Fittings bath filler shower arm etc are not provided with the bath and must be ordered separately Framing and enclosing materials are provided by others Check for availability of optional American Standard wall tiling bead required for recess installations Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth WARNING Do not lift whirlpool by the piping harness at any time FOR AFTER SALES SERVICE CALL 1 800 442 1902 WEEKDAYS American Standard Inc 2004 752294 100 Rev K All product names listed herein are trademarks of American Standard Inc unless otherwise noted INSTALLATION AND FRAMING INSTRUCTIONS The variety of installations possible for this whirlpool may require framing procedures other than those shown Locate studs as required Ensure roughing in dimensions are proper plumb and square Provisions must be made in all installations for an access opening for servicing the pump and controls It is strongly recommended that an additional opening be provided for access to the drain components NOTE The apron should not be used as the primary access opening 1 Position the whirlpool into the installation opening and level the deck shimming the integral support feet a
6. s necessary Mark the final position of the underside of the deck by tracing a line on to the studs see Figure 1 2 Remove the whirlpool and attach a 2 x 4 stringer to the studs with the top of the stringer touching the traced line 3 Install drain components to the whirlpool following the manufacturers instructions Before replacing your whirlpool for final installation be certain that an opening has been provided in the sub floor for the drain See the roughing in drawing for suggested opening size and location dimensions 4 Replace whirlpool and re shim the integral support feet shimming the entire length of the support feet Secure the shims using construction adhesive silicone mortar or equivalent materials While not a necessity the use of a foundation base consisting of cement e g Sakrete mortar or grout will help provide a solid and secure installation ge WATERPROOF DRYWALL STUD or CEMENT BOARD N FINISHED WALL WATERPROOF SEALANT we WHIRLPOOL FIG 1 FIG 2 TYPICAL RECESS INSTALLATION TYPICAL PIER TYPE INSTALLATION AS DESIRED 495mm 19 1 2 ic 1527mm 60 1 8 LEVELING STRINGERS LEVELING SURFACE WATERPROOF SEALANT NOTE RECESSED INSTALLATIONS REQUIRE THE FINISHED WALL TO COME THE DOWN TO THE TOP SURFACE OF THE TUB See Fig 2 UNLESS AN ACCESS OPENING OF AT LEAST 12 X 24 305 X 610MM IS PROVIDED WARRANTY SE
7. se wire brushes or any other metal implement on bath surface Post installation clean up generally can be completed using warm water and liquid dishwashing detergent Stubborn dirt or stains may be removed using granular Spic and Span mixed with water Painter s naphtha can be used to remove excess adhesives and or wet oil base paint HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES Abrasive cleaners must not be used since they will scratch and dull the surface Dulled areas can be restored by rubbing with a white automotive type polishing compound and waxing with a liquid wax 752294 100 Rev K 4 spic AND SPAN Is A REGISTERED TRADEMARK OF PROCTER amp GAMBLE
Download Pdf Manuals
Related Search