American Standard Culinaire Single Control Kitchen Faucet with Hi-Flow Spout 4147.001 User's Manual
Contents
1. CAN BE INSTALLED FOR RIGHT OR LEFT HAND APPLICATIONS Use a screwdriver to tighten the SCREWS 9 on LOCKNUT 7 Work your way around LOCKNUT 7 tightening the SCREWS 9 slightly each time until all are snug to ensure even pressure 2 MAKE WATER SUPPLY CONNECTIONS NOTE FLEXIBLE SUPPLIES HAVE TO BE PURCHASED SEPARATELY m Carefully bend COPPER SUPPLIES to meet water supply lines using the palms of the hands to avoid kinking Connect HOT water supply line to left tube and COLD water supply line to right tube using appropriate connectors Use 1 2 IPS FLEXIBLE SUPPLIES 3 or 3 8 O D BULL NOSE RISERS 4 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to FERRULE proper length A INSTALL SPRAY HOLDER Note For installation less hand spray see step 4a m Place SPRAY HOLDER 1 into separate hole of SINK 2 mE Assemble the SPRAY HOLDER WING NUT 3 onto the shank of SPRAY HOLDER 1 from below and tighten Do not use putty CONNECT HOSE SPRAY Feed SPRAY HOSE 1 eee SPRAY HOLDER 2 and attach COUPLING NUT 3 of HOSE 1 to HOSE ADAPTOR 4 on valve body Tighten COUPLING NUT 3 firmly 4a CAP HOSE ADAPTER m Cap HOSE ADAPTER 1 with PIPE CAP 2 supplied with faucet M968209 REV 1 1 TEST INSTALLED FAUCET CHECK CONNECTIONS Move HANDLE 1 into off position and re2. Installation Instructions Culinaire 4147 001 SINGLE CONTROL KITCHEN FAUCET WITH HI FLOW SPOUT with EverClean Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets EverClean Finish e One wipe effortlessly removes spots Magne REN ii e Eliminates the need for cleaners and scrubbing e Permanent surface protectant remains beautiful for the life of the faucet e EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes To ensure that your installation proceeds smoothly please read these instructions carefully before you begin TP See Phillips Screwdriver Channel Locks Adjustable Wrench Certified to comply with ANSI A112 18 1M TOOLS REQUIRED Plumbers Putty or Caulking Tubing Cutter INSTALL FITTING WITH OR WITHOUT DECK ESCUTCHEON T ff hot and cold wat CAUTION supplies Before beginning Apply a bead of putty to bottom edge of ESCUTCHEON 1 Note Installation of ESCUTCHEON 1 is optional Make certain the large SEAL 2 is properly seated in recess of faucet body Insert supply TUBES 3 and SHANK 4 through center hole of ESCUTCHEON 1 if used and sink Assemble RUBBER WASHER 5 BRASS WASHER 6 and threaded LOCKNUT 7 onto SHANK 4 from underside of sink Hand tighten LOCKNUT 7 and check that faucet is centered NOTE FAUCET
3. move AERATOR 2 FOR LEAKS with KEY 3 supplied Turn on water supplies and check connections for leaks Operate HANDLE 1 on and off hot and cold to flush water lines thoroughly Direct SPRAY 4 into sink and activate Check hose connections for leaks E Move HANDLE 1 to off position and replace AERATOR 2 SERVICE Reduced flow If the flow should gradually be reduced over a number of months the AERATOR may have debris in it To clean remove AERATOR 1 with KEY 1a and rinse with water to remove any debris Turn on faucet to wash any debris out of the faucet Screw AERATOR 1 back to the spout Operate faucet Spout leakage If fitting leaks above SPOUT HUB 2 remove SPOUT 3 as follows and check SPOUT O RINGS 4 m Loosen SET SCREW 5 and pull SPOUT 3 off Remove SPOUT 3 by pulling up gently while moving SPOUT 3 side to side Check both SPOUT O RINGS 4 Replace if necessary E Reverse procedure to reinstall SPOUT 3 Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then m Remove BUTTON 11 and loosen HANDLE SCREW 141 and remove HANDLE 6 E Unscrew ESCUTCHEON CAP 7 Unscrew the CARTRIDGE NUT 8 m Remove CARTRIDGE 9 Clean inlets of CARTRIDGE 9 and MANIFOLD 10 E Reassemble CARTRIDGE 9 Replace CARTRIDGE NUT 8 CAP 7 and HANDLE 6 assembly check flow On models with SPRAYS DIVERTER 12 can be cleaned with SPOUT 3 rem
4. oved by unscrewing DIVERTER 12 out of the SPOUT RECESS 13 Clean DIVERTER 12 and SPOUT RECESS 13 Replace DIVERTER 12 back into SPOUT RECESS 13 Reverse procedure to reinstall SPOUT 3 F EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968209 REV 1 1
Download Pdf Manuals
Related Search