American Standard Connoisseur 4400 SERIES User's Manual
Contents
1. Check both SPOUT O RINGS 11 Replace if necessary AERATOR On models with SPRAYS DIVERTER 10 can be cleaned by pulling DIVERTER 10 out of the MANIFOLD 13 Clean DIVERTER 10 and MANIFOLD 13 Push DIVERTER 10 back into MANIFOLD 10 E Reverse procedure to reinstall SPOUT CARTRIDGE and HANDLE Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then E Remove PLUG BUTTON 2 loosen HANDLE SCREW 1 and remove HANDLE 3 E Remove ESCUTCHEON CAP 4 unscrew the three CARTRIDGE SCREWS 6 E Clean inlets of CARTRIDGE 7 and MANIFOLD 13 E Reassemble CARTRIDGE 7 alternately tightening SCREWS 6 Replace CAP 4 and HANDLE 3 Check flow HOT LIMIT SAFETY STOP ADJUSTMENT By restricting handle rotation and limiting the amount of hot water allowed A to mix with the cold the HOT LIMIT SAFETY STOP reduces risk of accidental PRY RED RING FORWARD scalding To set the maximum hot water temperature of your faucets all you AND ROTATE COUNTER need to do is adjust the setting on the HOT LIMIT SAFETY STOP CLOCKWISE ONE CLICK Remove HANDLE BUTTON 1 and loosen SET SCREW 2 Pull euler eee A A HANDLE 3 off valve stem Pull off CAP 4 Use a flat blade B screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP 5 Follow Step A or B to adjust ARY ROTATE CLOCKWIGE min max discharge temperature O being the hottest to n 7 the col2. m For installation less spray cap off SPRAY HOSE CONNECTION with PIPE CAP 6 SPRAY HOSE CONNECTION 4 CONNECT HOSE SPRAY m Feed SPRAY HOSE 1 through SPRAY HOLDER 2 and attach COUPLING NUT 3 of HOSE 1 to HOSE ADAPTOR 4 on valve body Tighten COUPLING NUT 3 firmly M968955 REV 1 2 5 TEST INSTALLED FAUCET Move HANDLE down into off position and remove AERATOR Turn on water supplies and check connections for leaks m Operate HANDLE up and down left and right to flush water T lines thoroughly AERATOR For faucet with spray direct SPRAY HEAD into sink and activate SPRAY Check hose connections for leaks m Move HANDLE down to off position and replace AERATOR CHECK CONNECTIONS FOR LEAKS m SERVICE Reduced flow If the flow gradually reduces over a number of months the AERATOR may have collected debris To clean remove AERATOR and rinse with water and remove any debris Turn on faucet to wash any debris out of the faucet Thread AERATOR back into spout Operate faucet Spout leakage If fitting leaks above or below SPOUT HUB remove SPOUT as follows and check SPOUT O RINGS and SPACER O RINGS m Remove HANDLE BUTTON 2 and loosen SET SCREW 19 Pull HANDLE 3 off valve stem E Remove CAP 4 and and RETAINER 5 Loosen CARTRIDGE SCREWS 6 and 12 remove CARTRIDGE 7 Pull off SPACER 8 and O RINGS 9 Remove SPOUT 12 by pulling up gently while moving SPOUT 12 side to side k
3. Americam Standard Installation Inst ti CONNOISSEUR A400 SERIES SINGLE CONTROL KITCHEN FAUCET AND CAST SPOUT Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly Certified to comply with ANSI A112 18 1M please read these instructions carefully before you begin M968955 REV 1 2 TOOLS REGUIRED yo gt Phillips Screwdriver a Channel Locks Adjustable Wrench Plumbers Putty or Caulking Regular Screwdriver 3 INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON 1 CAUTION Turn off hot and cold water supplies before beginning A Installation with ESCUTCHEON 1 Apply a bead of putty to bottom edge of ESCUTCHEON WITH PUTTY PLATE 1 Insert supply HOSES 3 and SHANK 4 through hole of ESCUTCHEON WITH PUTTY PLATE 1 and mounting surface Make certain the SQUARE SEAL RING 2 is properly seated in recess of SPOUT BASE Follow mounting instructions below to secure faucet to mounting surface B Installation less ESCUTCHEON 1 Remove ESCUTCHEON WITH PUTTY PLATE 1 and Insert supply HOSES 3 and SHANK 4 through mounting hole and seat SPOUT BASE onto sink or mounting surface Make certain the SQUARE SEAL RING 2 is properly seated in recess of SPOUT BASE Do not use putty Assemble RUBBER WASHER 5 BRASS WASHER 6 and threaded LOCKNUT 7 onto SHANK 4 from underside of sink or
4. dest temperature setting Factory set at O B ADJUSTMENT WHEN Replace ESCUTCHEON CAP 4 HANDLE 3 tighten WATER IS TOO COLD HANDLE SCREW 1 and install INDEX BUTTON 2 RED RING HOT LIMIT SAFETY STOP M968955 REV 1 2
5. mounting surface Hand tighten LOCKNUT 7 and check that rotation of HANDLE 8 from HOT to COLD is centered Use a screwdriver to tighten SCREWS 9 on LOCKNUT 7 Work your way around LOCKNUT 7 tightening the screws slightly each time until all are snug to ensure even pressure SPOUT BASE SQUARE SQUARE SEAL RING C I SEAL RING SINK m MOUNTING SURFACE 2 MAKE WATER SUPPLY CONNECTIONS E Turn off hot and cold water supplies before beginning E Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left supply to Hot Marked with a Red Tag and right supply to Cold wall supply Use adjustable wrench to tighten connections Do not over tighten m Faucet supplies are 21 long from faucet base m Note If additional supply length is required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are too long loop as illustrated to avoid kinking INSTALL SPRAY HOLDER E On model with separate spray place the SPRAY HOLDER 1 into the appropriate mounting hole Assemble the SPRAY HOLDER WING NUT 2 onto the shank of SPRAY HOLDER 1 from below and tighten Do not use putty B On model with spray through the ESCUTCHEON 3 place SPRAY HOLDER 4 into the hole of ESCUTCHEON 3 Assemble SPRAY HOLDER NUT 5 onto the shank of SPRAY HOLDER 4 from below and tighten Do not use putty
Download Pdf Manuals
Related Search