American Standard Chandler Americast 7162 User's Manual
Contents
1. Toll Free 800 387 0369 791266 400 Rev B 5 Apply a masking tape outline 1 8 outside traced outline as a guide for application i of silicone A Maskin Se Sink sealant tape 3 17 outline outline Apply a generous portion of silicone sealant inside line traced on countertop Carefully lower sink into place and press down firmly Use guidelines for proper positioning Using water to dampen your finger remove excess sealant for a smooth even line Apply additional sealant if necessary to provide a uniform bead from the rim of sink to the masking tape line as shown Carefully remove tape Dampen finger and run it slightly over the sealant to remove any high spots Use mineral spirits to remove excess silicone from countertop and sink e i Silicone Sink Masking Sealant DS NOTE Silicone must be removed within 10 minutes of application or a permanent residue may remain on the surfaces Connect supply lines to faucet finger tight and carefully bend to engage with the supply stops Tighten connections to faucet for secure seal Connect drain assembly hand tight to check alignment lt may be necessary to cut off part of the tailpiece area A or part of the horizontal leg of the trap area B Secure joint for water tight assembly oe Trap Trap Single Bowl Double Bowl CARE AND CLEANING For all porcelain enamel surfaces regular gentle care is best The recommended way to preserve the2. Installation Instructions CHANDLER AMERICAST KITCHEN SINK DOUBLE BOWL MODEL 7255 SINGLE BOWL MODEL 7162 Certified to comply with ANSI A112 19 4 M Thank you for selecting American Standard the benchmark U S Patent No 4 664 982 of fine quality for over 100 years Other patents pending CAN C S A B 45 To ensure that your installation proceeds smoothly please abaerie lodi plumi Naand bla godes read these instructions carefully before you begin l BEFORE YOU BEGIN Unpack new sink and inspect carefully for damage Replace the sink in its original packing carton to protect it until you are ready to begin installation Recommended Tools amp Materials Silicone Sealant Mineral Spirits Putty Knife Basin Wrench Pipe Wrench Saber Saw Channel Locks Tubing Cutter Phillips Screwdriver Tape Measure Regular Screwdriver Hacksaw Adjustable Wrench Scissors Drill DOUBLE BOWL MODEL 7255 CUTOUT FOR NEW INSTALLATION 36 914mm 32 813mm 10 1 2 267mm Ue 21 533 CUTTING SINK Li 2rTYP LINE OUTLINE MODIFICATION REQUIRED TO FIT CHANDLER SINK INTO A STANDARD 33 X 22 SINK CUTOUT 35 889mm 1 1 2 38mm y 21 533mm 32 813mm _ 19 1 2 495mm t Radius T l BrE Zigga CENTER LINE ae 19 1 2 495mm CUTTING a 1 2 TYP LINE SINK OUTLINE 791266 400 Rev B CUTOUT DIMENSIONS FOR SINK Locate and mark center li
3. finish avoid scratches and clean porcelain enamel fixtures is to rinse them with detergent and water Generally any of the light duty liquid dishwashing detergents such as Palmolive or Dawn work well In areas where the water is hard a heavy duty liquid laundry detergent such as liquid Tide will work better Product names listed herein are trademarks of American Standard Inc unless otherwise noted Palmolive is a registered trademark of Colgate Palmolive Co Tide and Dawn are registered trademarks of Procter and Gamble American Standard Inc 2003
4. nes of sink on countertop Provide proper clearance under the countertop for the faucet supply lines and the structural parts of the cabinet Cut out correct template and trace the cut line onto the countertop at the proper location NOTE f replacing an existing sink be certain to shut off water supplies before removing old sink SINGLE BOWL MODEL 7162 CUTOUT FOR NEW INSTALLATION 28 711mm 24 610mm 10 1 2 267mm i 21 533 CUTTING SINK Lave typ LINE OUTLINE MODIFICATION REQUIRED TO FIT CHANDLER SINK INTO A STANDARD 25 X 22 SINK CUTOUT 27 686mm 1 1 2 38mm F 21 533mm 24 610mm i p ci 19 1 2 495mm a fas CENTER LINE ain 19 1 2 495mm CUTTING a E 1 2 TYP LINE SINK OUTLINE Product names listed herein are trademarks of American Standard Inc unless otherwise noted American Standard Inc 2003 AFTER THE CUTOUT IS DRAWN Drill a clearance hole inside the cutout line as marked on the countertop Perimeter of sink Cut opening on cut line inside the peri meter of sink Mount the faucet and drain assembly on the sink following the manufacturer s instructions Before applying the sealant place the sink temporarily into the cutout Check for alignment and clear ance then trace around the outside edge of the sink as a guide for installation location and application of sealan
5. or if it was modified in a manner inconsistent with the product as shipped by American Standard American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to province in which case this warranty does not affect such statutory rights For service under these warranties it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the United States American Standard Inc P O Box 6820 In Canada American Standard 2480 Stanfield Rd Mississauga Ontario Canada L4Y 1S2 Piscataway New Jersey 08855 Attention Director of Consumer Affairs For residents of the United States warranty information may also be obtained by calling the following toll free number 800 442 1902
6. t Remove sink AMERICAST LIMITED LIFETIME WARRANTY If an American Standard Americast brand product is found to be defective in materials or workmanship after inspection by an authorized American Standard representative American Standard will repair or at its option exchange the product for a similar model This warranty extends for the lifetime of the product so long as it remains in use in its original place of installation except that the warranty applies to a bathing vessel s slip resisting surface only for the first year after the product s initial installation This warranty applies only to the original purchaser and installation of these products This warranty does not apply to whirlpool components or to faucets drains mounting rims grab bars or other accessories If manufactured or supplied by American Standard such whirlpool components and accessories are covered under separate limited warranties This warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to assure local code compliance before installation This warranty shall be void if the Americast brand product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damage if it was not installed in accordance with American Standard s instructions
Download Pdf Manuals
Related Search