Pyle PLBASS2.8 audio amplifier
Contents
1. 2 1CH 8 Super Slim Active Subwoofer OWNER S MANUAL Congratulations on you purchase of a PYLE PLBASS2 8 2 1CH Slim Amplified Subwoofer It has been designed engineered and manufactured to bring you the highest level of performance and quality and will afford you years of listening pleasure Thank you for making a PYLE your choice for car audio entertainment PLBASS2 8 8 Slim Woofer RCA Low Level Input High Level Input Green amp Red LED Power Status Indicator Phase shift Switch 0 or 180 soft delay remote Turn On Thermal Short And Overload Protection Circuits Fuse 2 15A RMS Power 150W x2 300Wx1 MXA Power 300Wx2 600W 1 Subwooofer Gain Control Subsonic Filter 20 50Hz 0 to 12dB Variable Bass Boost 45HZ Low Pass Filter 50 150 Hz Subwoofer Gain Remote Control CH 1 2 Gain Control High Pass Filter 50 150 Hz Dimension 14 5 L x 9 5 W x 3 H Weight 11 6 LBS Introduction With the PLBASS2 8 we are introducing a low profile 2 1CH amplified subwoofer Low enough to easily fit below the seat of you car This system offers you a quick and easy way to add a high powered 2CH amplifier and subwoofer system to your audio system The PLBASS2 8 contins a 2CH fullrange amplifier and an amplifiered subwoofer Both high level speaker level and low level RCA type inputs are present making this a universal solution for use with any head unit or other inpu2. your amplifier at the same time PELI To Audio Les Outuputs of head unit or signal processor High Level Input Wiring The high level input s should only be used when your receiver lacks RCA outputs If the RCA outputs are not present connect the speaker outputs from the receiver to the high level input connector of the amplifier Be sure to observe polarity to avoid audio phase problems NOTE Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time k fe TO Speaker Terminals 7 of head unit 6 SPEAKER OUTPUT WIRING Connect to the full range front or rear dieci in your car pre p om e pr j er k aa r kd aa r k Power Connections SPEAKERS Connect the ground terminal to the closest point on the chassis of the vehicle Keep this ground wire to less than 39 100 cm inlength Use 8 gauge or heavier wire Connect the remote terminal to the remote output of the head unit using 16 gauge or heavier wire Connect an empty fuse holder within 18 45 cm of the car battery and run 8 gauge or heavier cable from this fuse to the amplifier location Then connect the fuse holder to the BATT connection on the subwoofer rear panel to REMOTE TURN ON terminal of head unit instal the remote control securely under the dash orin a similar location where using it will Ta a not distract the driver Mounting the sub
3. he included remote level control to control the volume level of the subwoofer independently D SUBWOOFER SUBSONIC FILTER 20 50Hz CH1 2 GAIN CONTROL Set CH1 2 gain control after the subwoofer gain control is sets slowly turn up the CH1 2 gain control until you feel the best harmony of the music CH1 2 HIGH PASS FILTER E 50 150Hz i Rear panel controls and features 1 LOW LEVEL RCA INPUTS Low level inputs are the recommended way to introduce the audio signal to the subwoofer if RCA outputs are present on your head unit or other signal source such as a sound processor 2 HIGH LEVEL speaker level INPUTS If your head unit does not have RCA outputs you can use the speaker outputs for the audio source for the PLBASS2 8 Use the supplied cable and connect the outputs properly as shown in the connection diagram in this maunal CH1 2 SPEAKER OUTPUTS Connect to the full range front or rear speakers in your car 4 FUSE The fuse is rated at 154 Do not use a fuse with a different value and NEVER replace the fuse with a wire or coin amp POWER TERMINALS Low Level Input Wiring Low level RCA input wiring is preferred for best audio performance Most trunk or hatchback installations will require a 15 20 foot RCA cable while pickup trucks and under seat installations will require a 6 12 foot RCA cable Always use a high quality cable NOTE Do not connect BOTH the high level and low level inputs from your receiver to
4. t source For further flexibility in the use of a subwoofer a variable bass boost control has been included You can control the subwoofer level with the remote level control module What is included When first unpacking your new amplified subwoofer please check first that the package contains all of the items below If something is missing contact the store where you purchased the product PLBASS2 8 2 1CH amplified subwoofer Remote subwoofer level control Remote subwoofer control cable High level input wire 2CH speaker output wire Mounting hardware Front panel controls and features 1 POWER ON LED INDICATOR 2 PHASE SHIFT Use this switch to help compensate for time alignment problems in the system Such problems usually result from having the subwoofer at a different distance from the listener than the other speakers in the system SUBWOOFER GAIN CONTROL After you have installed your system turn this control to minimum Turn the head unit on and the subwoofer will turn on via the remote connection Turn the head unit volume to about 2 3 full level Slowly turn up the subwoofer input gain control until you hear a small amount of distortion Then reduce the level until the distortion is completely gone Leave the control at this setting 4 BASS BOOST The bass boost feature will increase the sound level of the bass frequencies LOW PASS FILTTER 50 150Hz 6 REMOTE LEVEL CONTROL PORT Attach t
5. woofer 1 Find a suitable location in the vehicle in which to mount the amplifier A typical location is shown below 2 Make sure there is sufficient air circulation around the intended mounting location 3 Mark the location for mounting hole screws by positioning the cabinet where you wish to inst all it Make a small mark to identify the position and remove the unit Thoroughly clean the area you plan to attach the subwoofer using a vacuum cleaner Then attach the supplied double adhesive tape and put the subwoofer in the place and press down on it securely Troubleshooting If you experience operation or performance problems with this product compare your installation with the electrical wiring diagram on the previous pages If problems persist read the following troubleshooting tips which may help eliminate the problems PROBLEM POSSIBLE REASON SOLUTION NOH io power wie Check fuses and connections to battery Not switching on Power No power io remote wire Check remote on connections to head unit LED not on Fuse broken gt Rai fuaa vith cone yp a se voting butos POLO e SOT ummon No aa No sound Head Unit Check heed unit volume level Gan control not setup Ensure you have set up the amplifier gain level control A i Check all power remote on and ground Connegions sii PYLE www pyleaudio com
Download Pdf Manuals
Related Search