Finisar FTR-1319-3D-DD network transceiver module
Contents
1. Gigabit Interface Converter GBIC Revision 5 5 Sun Microsystems Computer Company et al August 16 1999 http playground sun com pub OEmod 2 IEEE Std 802 3 IEEE Standards Department 2002 3 Fibre Channel Physical and Signaling Interface FC PH FC PH2 FC PH3 American National Standard for Information Systems 4 Fibre Channel Draft Physical Interface Specification FC PI 13 0 American National Standard for Information Systems 5 AT24C01A 02 04 08 16 2 Wire Serial CMOS E7PROM Atmel Corporation www Atmel com XI For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale CA 94089 1134 Tel 1 408 548 1000 Fax 1 408 541 6138 sales finisar com www finisar com Finisar Corporation November 16 2007 Rev H3 Page 82. 7 Finisar II Electrical Power Interface Finisar FTR 1319 3D GBICs have an extended power supply voltage range of 3 15 V to 5 5 V as described in Table 2 They are compatible with both 3 3V and 5 V systems Parameter Notes Conditions Supply Current Inrush Current Tuge m Hot plug above steady state current Absolute Supply Voltage V max 0 3 Not to be applied continuosly Table 2 Electrical power interface III Low Speed Signals RX_LOS and TX_DISABLE are TTL signals as described in Table 3 MOD_DEF 1 SCL and MOD_DEF 2 SDA are open drain CMOS signals see section VII Serial Communication Protocol Both MOD_DEF 1 and MOD_DEF 2 must be pulled up to host_Vcc For more detailed information see sections 5 3 1 5 3 8 in the GBIC Specification Rev 5 5 Parameter Notes Conditions GBIC Output LOW 4 7k to 10k pull up to host_Vcc measured at host side of connector GBIC Output HIGH Vou host_Vcc 0 5 host_Vcc 0 3 V 4 1k to 10k pull up to host_Vcc measured at host side of connector GBIC Input LOW V V 4 7k to 10k pull up to Vcc measured at GBIC side of connector GBIC Input HIGH 4 7k to 10k pull up to Vcc measured at GBIC side of connector Table 3 Low speed signals electronic characteristics Finisar Corporation November 16 2007 Rev H3 Page 3 FTR 1319 3D Long Wavelength GBIC Specification November 2007 Finisar Parameter i Units Notes Conditions RX_L
3. Finisar Product Specification Long Wavelength GBIC Transceiver FTR 1319 3D Product Features e Upto 1 25Gb s bi directional data links e 1310nm Fabry Perot laser transmitter e Optional Digital Diagnostics e Extended operating temperature range 10 C to 85 C Applications e Compatible with 3 3 amp 5V systems e 1 0625 Gb s Fibre Channel e 1 25 Gigabit Ethernet e Hot pluggable complies with GBIC specification Rev 5 5 e Fully metallic enclosure for low EMI e Low power dissipation Finisar s FTR 1319 3D 1310nm GBIC transceivers comply with GBIC Specification Revision 5 5 They are compatible with Gigabit Ethernet as specified in IEEE 802 37 Fibre Channel FC PH PH2 PH3 and FC PI 13 0 Product Selection Part Number Digital Diagnostics FTR 1319 3D No FTR 1319 3D DD Yes Finisar Corporation November 16 2007 Rev H3 Page 1 FTR 1319 3D Long Wavelength GBIC Specification November 2007 Finisar I Pin Out np oxo moo MOD DEFO MOD_DEF 2 2 3 4 5 CTX DISABLE 7 oa e TX_FAULT 10 not supported GND Table 1 GBIC to host connector pin assignment Sequence indicates the order in which pins make contact when the device is hot plugged See Table 3 Signal Definitions in the GBIC Specification Revision 5 5 Finisar Corporation November 16 2007 Rev H3 Page 2 FTR 1319 3D Long Wavelength GBIC Specification November 200
4. OS Assert Level a E RXLOSHysteresis os _ RX_LOS Assert Delay t_loss_on 100 usec 8 detection es loss of signal to assertion of RX_LOS RX_LOS Pree Delay t_loss peace I faa usec From detection of presence of signal to negation of RX_LOS ieee _DISABLE Assert Time t_ ie usec Rising edge of TX_DISABLE to fall of output signal below 10 of nominal TX_DISABLE Negate Time a 1000 usec Falling edge of TX_DISABLE to rise of output signal above 90 of nominal TX_DISABLE Reset Time t_reset 10 usec TX_DISABLE HIGH before TX_DISABLE set LOW Table 4 Low speed signal parameters IV High Speed Electrical Interface All high speed PECL signals are AC coupled internally Parameter i i Notes Conditions Data Input Voltage PECL differential peak peak Data Onpui Voltage v o 2000 mV O PECL differential peak peak PECL sal a 1 e ae BicErorRate se o PRBS 2 T test data pater O S S om x Output impedance Zon 73 om SSS Table 5 High speed electrical interface Finisar Corporation November 16 2007 Rev H3 Page 4 FTR 1319 3D Long Wavelength GBIC Specification November 2007 Finisar vV Optical Parameters Units Notes Conditions TRANSMITTER CHARACTERISTICS Transmitter Center Wavelength Transmitter Spectral Width A nm RMS Also meets curves in FC PI 10 0 Figures 18 re ee into aaa mode fiber Transmiter Extinction Ratio OM 9 Tammie Eye Ope
5. ning Channel Eye Masks Transmitter Rise Fall Time tr tf 20 80 differential unfiltered ae rt eee Relative Intensity Noise 120 dB Hz RECEIVER CHARACTERISTICS Optical Input Wavelength es a O T a O e Optical mpu Power 2568A Pa 9 f 3 f abm BER 10 w PRES Onenen Poner CS e a fsa 27 1 test pattern Total Receiver Jitter Peak to peak filtered in loopback Note Parameters are specified over temperature and voltage at end of life unless otherwise noted Table 6 Optical parameters Units Notes Conditions Gb sec Fibre Channel IEEE 802 3 Compatible Foer j ooo m foum Core Single Mode Fiber Fibertensth L __ 350 m opm s00MHzkm Fiber Fibertensth Fiber Length L 275 m 62 5um200MHzkmFiber_ Table 7 General specifications Finisar Corporation November 16 2007 Rev H3 Page 5 FTR 1319 3D Long Wavelength GBIC Specification November 2007 Finisar VII Environmental Specifications Note that the GBIC Specification requires an ambient temperature range of 0 to 50 C The FTR 1319 3D has an extended range from 10 C to 85 C case temperature as specified in Table 8 Parameter i Units Notes Conditions npon ey C Case Tipsy Rai iy Rt 0 Ren eg StorageTemp Tw 0 fes C mo Safety a and IEC 825 Class Laser Product See Note 1 Note 1 Complies with FDA performance standards for laser products except for deviations pursua
6. nt to Laser Notice No 50 dated July 26 2001 Table 8 Environmental specifications VIII Serial Communication Protocol All Finisar optical GBICs implement serial identification features described for Module Definition 4 as outlined in Annex D of the GBIC Specification These GBICs use an Atmel AT24C01A 128 byte E7PROM at address AOH For details on interfacing with the E PROM see the Atmel data sheet titled AT24C01A 02 04 08 16 2 Wire Serial CMOS EPROM Parameter Symbol i Max Units Notes Conditions TC Clock for Atmel Catmel 100 000 Bus can be driven blind AOH and Controller IC A2H Table 9 P C timing requirements Finisar Corporation November 16 2007 Rev H3 Page 6 FTR 1319 3D Long Wavelength GBIC Specification November 2007 Finisar IX Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5 5 Section 6 Parameter GBIC insertion F GBIC retention FR Table 10 Insertion extraction and retention forces 1 03 REF I SINGLE MODE 1310 nm FIR 1319 30 DATE 2 57 REF Ls 000 1 2 006 z T k 393 005 Gel 47 003 m 2 25 010 Figure 1 GBIC outline drawing Finisar Corporation November 16 2007 Rev H3 Page 7 FTR 1319 3D Long Wavelength GBIC Specification November 2007 Finisar X References 1
Download Pdf Manuals
Related Search