Finisar XFP 1310nm 10km SMF
Contents
1. Digital Diagnostic Functions As defined by the XFP MSA Finisar XFP transceivers provide digital diagnostic functions via a 2 wire serial interface which allows real time access to the following operating parameters Transceiver temperature Laser bias current Transmitted optical power Received optical power Transceiver supply voltage It also provides a sophisticated system of alarm and warning flags which may be used to alert end users when particular operating parameters are outside of a factory set normal range The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller DDTC inside the transceiver which is accessed through the 2 wire serial interface When the serial protocol is activated the serial clock signal SCL pin is generated by the host The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write protected The negative edge clocks data from the XFP transceiver The serial data signal SDA pin is bi directional for serial data transfer The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation The memories are organized as a series of 8 bit data words that can be addressed individually or sequentially The 2 wire serial interface provides sequential or random access to the 8 bit parameters addressed from 000h to the maximum address of the memory For more detailed informatio2. interface equivalent to a power cycle Z a US 1 8V Power n 3 Not required GND Module Ground Ground LLILAE E host board Not reduired ape pe NEN board Not required 26 GND ModuleGround a ie Gnd O 28 CMLI TD Transmiterinverted data input 29 CMLI TD Transmitter non inverted data input 30 X GND ModuleGround f l1 Notes 1 Module circuit ground is isolated from module chassis ground within the module 2 Open collector should be pulled up with 4 7k 10kohms on host board to a voltage between 3 15 V and 3 6V 3 A Reference Clock input is not required by the FTLX1413D3BCL If present it will be ignored Finisar Corporation March 2013 Rev Cl Page 2 FTLX1413D3BCL Datacom XFP Product Specification March 2013 Finisar Geo yy 45 16 EN ovo x RX LOS 14 17 ESI np Moo NR 13 18 RD i Mop Ass 3l 12 19 GND l SDA 11 20 VCC2 SCL 10 24 P DOWN VCC3 19 22 3 vcc2 A TOWARD 23 EG Tutos TOWARD ASIC g BEZEL GNO 24 RerCLK ees es vecs pm 6 25 7 REFCLK TX_DIS 5 26 GND INTERRUPT p 4 27 GND T 1 Moo DestEL i3 28 EJ TD VEES p 2 29 TD pum GNO l1 30 GND E Diagram of Host Board Connector Bloc
3. Datacom XFP Product Specification March 2013 Finisar I Pin Descriptions Pin Logic Symbol Name Description pop GND Module Ground L3 2s VEES Optional 5 2 Power Supply Not required L 3 EIU moane Module De select When held low allows the module to respond to 2 wire serial interface commands LVTTL O Interrupt bar Indicates presence of an important condition 2 ELGUE M oe 5 LVTTLI TX DIS Transmitter Disable Transmitter laser source turned off 6 VCCS 45PowerSupply Notrequred 7 GND ModueGrund gt l 8 VCC 433VPowrSuply 9 VCC 33V Power Supply MEN LVTTL I Serial 2 wire interface clock I O Module Absent Indicates module is not present Grounded in the module Module Not Ready Finisar defines it as a logical OR between RX LOS and Loss of Lock in TX RX 15 GND ModueGrund gt l Te GM ee OOO M m 17 CMLO RD JReceiverinverteddataouput E MLO RDE Receiver non inverted eua GND ModuleGround 0 ND Module Ground L m 1 8V Power Supply Not required po 21 LVTTL I P_Down RST Power Down When high places the module in the low power stand by mode and on the falling edge of P_Down initiates a module reset Reset The falling edge initiates a complete reset of the module including the 2 wire serial
4. Finisar Product Specification 10Gb s 10km Datacom XFP Optical Transceiver FTLX1413D3BCL PRODUCT FEATURES e Supports 8 5Gb s to 10 5Gb s bit rates L A e Power dissipation 1 5W e Commercial temperature range 5 C to 75 C m E e RoHS 6 Compliant lead free ab e Hot pluggable XFP footprint e Single power supply 3 3V e Maximum link length of 10km APPLICATIONS e Uncooled 1310nm DFB laser 10GBASE LR LW 10G Ethernet e Duplex LC connector 1200 SM LL L 10G Fibre Channel e No Reference Clock required and 800 SM LC L 8G Fibre Channel e Built in digital diagnostic functions 10G CPRI Finisar s FTLX1413D3BCL Small Form Factor 10Gb s XFP transceivers are compliant with the current XFP Multi Source Agreement MSA Specification They comply with 10 Gigabit Ethernet IOGBASE LR LW per IEEE 802 3ae 10G Fibre Channel 1200 SM LL L 8G Fibre Channel 800 SM LC L and 10G CPRI This transceiver can also support OTN FEC protocols OTUle and OTU2e upon request Digital diagnostics functions are available via a 2 wire serial interface as specified in the XFP MSA If SONET SDH compliance is required please see Finisar Part Number FTLXI413M3BCL The transceiver is RoHS compliant and lead free per Directive 2002 95 EC and Finisar Application Note AN 2038 PRODUCT SELECTION FTLX1413D3BCL Please contact Finisar for higher data rate support Finisar Corporation March 2013 Rev Cl Page 1 FTLX1413D3BCL
5. W aS So AN CENTERLINE OF RECTANGULAR PAD S ce ie MAX I4 PLC 0 5 0 03 aimi um 30 PLC 240 05 5 2 TR f LS 1 55r0 05 DETAIL 2 SCALE 8 1 XFP Detail Host Board Mechanical Layout dimensions are in mm BEZEL OPENING ABOVE HOST BOARD ZN FOR PCI APPLICATIONS RECOMMENDED DIMENSION 18 0 4 AX MINIMUM PITCH REDE AX SEE SECTION 5 8 FOR CALCULATION OF GASKET THICKNESS AFTER COMPRESSION XFP Recommended Bezel Design dimensions are in mm Finisar Corporation March 2013 Rev Cl Page 10 FTLX1413D3BCL Datacom XFP Product Specification March 2013 Finisar XI References l 10 Gigabit Small Form Factor Pluggable Module XFP Multi Source Agreement MSA Rev 4 5 August 2005 Documentation is currently available at http www xfpmsa org 2 Application Note AN 2035 Digital Diagnostic Monitoring Interface for XFP Optical Transceivers Finisar Corporation December 2003 3 Directive 2002 95 EC of the European Council Parliament and of the Council on the restriction of the use of certain hazardous substances in electrical and electronic equipment January 27 2003 4 Application Note AN 2038 Finisar Implementation Of RoHS Compliant Transceivers Finisar Corporation January 21 2005 XII For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale CA 94089 1133 Tel 1 408 548 1000 Fax 1 408 541 6138 sales finisar com www finisar com Finisar Corpora
6. k Pin Numbers and Name II Absolute Maximum Ratings Parameter Symbol Min Typ Max Unit Ref HMeimumSupy Voltage ves a5 49 Y Storage Temperature MN 4 f s Case Operating Temperature Te 5 j 7 c Finisar Corporation March 2013 Rev Cl Page 3 FTLX1413D3BCL Datacom XFP Product Specification March 2013 Finisar III Electrical Characteristics Top 5 to 75 C Vcc3 3 13 to 3 45 Volts Supply Voltage Ves 38 as V Supply Core eo m Module total power sw Input differential impedance Rae 19 Q 2 Differential data input swing Vinpp 120 so m Transmit Disable Voltage V 20 Ve V 3 Transmit Enable Voltage Vw GND GNDeO8 V TransmitDisable Asset Time 10 us Receiver Dataoutputrisetime t O 38 ps 5 Data output fall ime t 38 ps 5 LOS Fault Viosma Vcc 05 Vecuosr V 6 LOS Normal Viossom GND GND 0 5 V J6 Power Supply Rejection Notes 1 Maximum total power value is specified across the full temperature and voltage range 2 After internal AC coupling 3 Oropen circuit 4 Into 100 ohms differential termination 5 20 80 6 Loss Of Signal is open collector to be pulled up with a 4 7k IOkohm re
7. n including memory map definitions please see Finisar Application Note AN 2035 Digital Diagnostic Monitoring Interface for XFP Optical Transceivers or the XFP MSA Specification Finisar Corporation March 2013 Rev Cl Page 7 FTLX1413D3BCL Datacom XFP Product Specification March 2013 Finisar IX Mechanical Specifications Finisar s XFP transceivers are compliant with the dimensions defined by the XFP Multi Sourcing Agreement MSA mn rd nri my leo T R JI Ni O 4 Y PRODUCT LABEL J SS oT UNLATCHED 20 85 39 00 R1 00 XFP Transceiver dimensions are in mm Finisar Corporation March 2013 Rev Cl Page 8 FTLX1413D3BCL Datacom XFP Product Specification March 2013 Finisar X PCB Layout and Bezel Recommendations or CEJ amp EC SEE DETAIL Z LLLA N ONNAN NINNA N Z A 5 7 r SESS SESS TTA A 22 15 MIN ee P 1 MU US pe VAL IIT LP A TERRI S CROSS HATCHED AREA DENOTES COMPOWENT AND TRACE KEEP OUT EXCEPT CHASSIS GROUND THIS AREA DENOTES 3 6 COMPONENT KEEP OUT TRACES ALLOWED AN DATUM X AND ESTABLISHED BY CUSTOMER S FIDUCIALS A DATUM IS TOP SURFACE OF HOST BOARD 39 2 MIN AA INDICATED SURFACES TO BE CONDUCTIVE AND COMMECTED TO CHASSIS GROUND XFP Host Board Mechanical Layout dimensions are in mm Finisar Corporation March 2013 Rev Cl Page 9 FTLX1413D3BCL Datacom XFP Product Specification March 2013 Finisar C Te e BSS MA
8. sistor to 3 15 3 6V Logic O indicates normal operation logic 1 indicates no signal detected 7 Per Section 2 7 1 in the XFP MSA Specification Finisar Corporation March 2013 Rev Cl Page 4 FTLX1413D3BCL Datacom XFP Product Specification March 2013 Finisar IV Optical Characteristics Top 5 to 75 C Vcc3 3 13 to 3 45 Volts Transmitter Optical Modulation Amplitude Poma dBm OMA 05 dBm Spc Wavelength 8 50 1889 m Sidemode Supression ratio SSRmin_ 30 dB Optical Exineion Rao e ss a Transmitter and Dispersion Penalty TDP Average Launch power of OFF Porr 5 transmitter Isa pet Pi Ca Receiver 10 5Gb s Eurer DD li OMA M ooo 10 5Gb s Maximum Input Power Pwx 05 m Optical Center Wavelength Ac 12600 160 nm ReceiverReflectance Re R dB LOSDeAset LO 8 dBm LOS Assert 1 LOS 2 Bm LOSHystrss o d 05 dB Notes 1 Measured with worst ER BER 10 2 1 PRBS 2 Per IEEE 802 3ae Equivalent to 13 3 dBm average power at Infinite ER 8 5Gb s Fibre Channel To operate the FTLX1413D3BCL at 8 5Gb s Fibre Channel the EEPROM Table 0 Byte 117 Bit O must be set as follows e EEPROM Byte 117 Bit 0 value 1 for 8GFC e EEPROM By
9. te 117 Bit 0 value 0 for 10Gb s rates o Itis also possible to bypass the CDRs with Byte 111 Bit 0 By default a power cycling the transceiver will return the transceiver to normal 10Gb s operation with the CDRs active Finisar Corporation March 2013 Rev Cl Page 5 FTLX1413D3BCL Datacom XFP Product Specification March 2013 Finisar V General Specifications BR l1 pe Max Supported Link Length Lux 1 0 ll km Notes 1 1OGBASE LR LW 1200 SM LL L 800 SM LC L and 10G CPRI 2 Tested with a 27 1 PRBS VI Environmental Specifications Finisar FTLX1413D3BCL transceivers have a commercial operating case temperature range of 5 C to 75 C Parameter Case Operating Temperature Storage Temperature 40 VII Regulatory Compliance Finisar XFP transceivers are Class 1 Laser Products They are certified per the following standards Feature Agency Standard Certificate Number FDA CDRH CDRH 21 CFR 1040 and Laser Notice 50 9210176 77 Safety Laser Eye TUV EN 60825 1 2007 EN60825 2 2004 A1 R72101686 Safety IEC 60825 1 2007 2 Edition IEC 60825 2 2010 3 Edition Safety Electrical UL CSA CLASS 3862 07 2283290 Safety CLASS 3862 87 Copies of the referenced certificates are available at Finisar Corporation upon request Finisar Corporation March 2013 Rev Cl Page 6 FTLX1413D3BCL Datacom XFP Product Specification March 2013 Finisar VIII
10. tion March 2013 Rev Cl Page 11
Download Pdf Manuals
Related Search