Finisar GBIC 1550nm 80km
Contents
1. Range Internal Transceiver Temperature Internal Transceiver Supply Voltage Tx Bias Current Tx Output Power Received Average Power Table 9 Digital Diagnostic Accuracy and Range Limits Finisar Corporation November 16 2007 Rev B1 Page 7 FTL 1519 3D 80km Extended Reach GBIC Product Specification November 2007 Finisar IX Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5 5 Section 6 Insertion Extraction and Retention Forces GBIC insertion GBIC extraction Fg GBIC retention eo 470 mn 7 irae Ti N N er Figure 1 GBIC outline drawing Finisar Corporation November 16 2007 Rev B1 Page 8 9 FTL 1519 3D 80km Extended Reach GBIC Product Specification November 2007 Finisar References Gigabit Interface Converter GBIC Revision 5 5 Sun Microsystems Computer Company et al August 16 1999 http playground sun com pub OEmod IEEE Std 802 3 IEEE Standards Department 2002 Fibre Channel Physical and Signaling Interface FC PH FC PH2 FC PH3 American National Standard for Information Systems Fibre Channel Draft Physical Interface Specification FC PI 2 Rev 10 American National Standard for Information Systems Directive 2002 95 EC of the European Council Parliament and of the Council on the restriction of the use of certain hazardous substances in e2. TRANSMITTER CHARACTERISTICS Se Sepp aso f a Pa oe a Spectral Width 20dB 20dB Transmitter Optical Output Power Poit m Average power al E mode fiber Transmitter Extinction Ratio eo ee Transmitter Eye Mask Margin i er to IEEE 802 3 and Fibre Channel Eye Masks P Raine ens Nabe Dispersion Penalty two __ 2 a8 _ WahSMP28 Tiber RECEIVER CHARACTERISTICS Receiver Reletanee Rag ufe Optical Input Power Pin dBm BER lt 10 w PRBS 2 1 test pattern 1 25Gb s Total Receiver Jitter Peak to peak filtered in loopback Note Parameters are specified over temperature and voltage at end of life unless otherwise noted Table 6 Optical parameters VI General Specifications Data Rate 125 Gb sec Fibre Channel IEEE 802 3 l ar A A oT a FiberLength km km 9 um Core Oum Core Single Mode Fiber Mode Fiber aaa ae E loss budget plus all other system penalties must not exceed 24 dB Table 7 General specifications Finisar Corporation November 16 2007 Rev B1 Page 5 FTL 1519 3D 80km Extended Reach GBIC Product Specification November 2007 Finisar VII Environmental Specifications Operating Temp To 0 70 C CweTempoaue Rete my R o f fes Non Condensing Storage Temp Tw 40 fs Eye Safety ta a IEC 825 Class 1 Laser Product See Note 1 Note 1 Complies with FDA performance standards for laser products except for deviations pursuant to
3. Laser Notice No 50 dated July 26 2001 Table 8 Environmental specifications VIII Serial Communication Protocol All Finisar optical GBICs implement serial identification features described for Module Definition 4 as outlined in Annex D of the GBIC Specification These GBICs use an Atmel AT24C01A 128 byte EPROM at address AOH For details on interfacing with the E PROM see the Atmel data sheet titled AT24C01A 02 04 08 16 2 Wire Serial CMOS E PROM The FTL 1519 3D also supports extended diagnostic features as described in Finisar Applications Note AN 2030 Digital Diagnostic Monitoring Interface for Optical Transceivers and additional information is available in SFF standard titled Digital Diagnostic Monitoring Interface for Optical Transceivers SFF 8472 rev9 3 A controller IC that monitors system parameters such as laser current module temperature transmitter power and received power is accessible at address A2H I2C clock speed digital diagnostic accuracy and digital diagnostic range can be found in the table below Values in the table represent the worst case values over temperature voltage and life Finisar Corporation November 16 2007 Rev B1 Page 6 FTL 1519 3D 80km Extended Reach GBIC Product Specification November 2007 Finisar Accuracy Internal Transceiver Temperature Internal Transceiver Supply Voltage Tx Bias Current Tx Output Power Received Average Power
4. in the GBIC Specification Revision 5 5 for a description of the function of each pin list above Finisar Corporation November 16 2007 Rev B1 Page 2 FTL 1519 3D 80km Extended Reach GBIC Product Specification November 2007 Finisar II Electrical Power Interface Finisar FTL 1519 3D GBICs have an extended power supply voltage range of 3 15 V to 5 5 V as described in Table 2 They are compatible with both 3 3V and 5V systems T O a M mA aoa Current Toure mA Hot Ie above steady State current Absolute Supply Voltage N nay 0 3 Not to be applied Referenced GND Table 2 Electrical power interface HI Low Speed Signals RX_LOS and TX_DISABLE are TTL signals as described in Table 3 MOD_DEF 1 SCL and MOD_DEF 2 SDA are open drain CMOS signals see section VIII Serial Communication Protocol Both MOD_DEF 1 and MOD_DEF 2 must be pulled up to host_Vcc For more detailed information see sections 5 3 1 5 3 8 in the GBIC Specification Rev 5 5 GBIC Output LOW 4 7k to 10k pull up to host_Vcc measured at host side of connector GBIC Output em ae host_Vcc 0 5 host_Vcc 0 3 4 7k to 10k pull up to host_Vcc measured at host side of connector GBIC Input LOW 4 7k to 10k pull up to Vcc measured at GBIC side of connector GBIC Input HIGH a eed he 4 7k to 10k pull up to Vcc measured at GBIC side of connector Table 3 Low speed signals electronic characteristics Finisar Corporation No
5. Finisar Product Specification RoHS Compliant 80km Extended Reach GBIC Transceiver FTL 1519 3D Product Features Up to 1 25Gb s bi directional data links 1550nm DFB laser transmitter Digital Diagnostics Extended operating temperature range 0 C to 70 C Compatible with 3 3 amp 5V systems Hot pluggable complies with GBIC specification Rev 5 5 Fully metallic enclosure for low EMI Low power dissipation RoHS Compliant and Lead Free Applications e 1 0625 Gb s Fibre Channel e 1 25 Gb s Ethernet Finisar s FTL 1519 3D 1550nm Extended GBIC transceivers have a maximum fiber length of 80km and comply with GBIC Specification Revision 5 5 They are compatible with Gigabit Ethernet as specified in IEEE 802 3 Fibre Channel FC PH PH2 PH3 and FC PI 2 Rev 10 They are RoHS 6 compliant per Directive 2002 95 EC and Finisar Application Note AN 2038 Finisar Corporation November 16 2007 Rev B1 Page 1 FTL 1519 3D 80km Extended Reach GBIC Product Specification November 2007 I Pin Out xos ft i a a E S E momo a 2 O E 2 a 6 2 Pexcpisaste 7 GND il i NO ea 0 1 if bd Rope coer o Vec Vec E S E E E p lt p lt p lt clk Z J p lt f pi i Table 1 GBIC to host connector pin assignment Finisar Sequence indicates the order in which pins make contact when the device is hot plugged See Table 3 Signal Definitions
6. lectrical and electronic equipment January 27 2003 AT24C01A 02 04 08 16 2 Wire Serial CMOS E7PROM Atmel Corporation www Atmel com Digital Diagnostics Monitoring Interface for Optical Transceivers SFF Document Number SFF 8472 Revision 9 3 Application Note AN 2030 Digital Diagnostic Monitoring Interface for Optical Transceivers Finisar Corporation April 2002 Application Note AN 2038 Finisar Implementation of ROHS Compliant Transceivers Finisar Corporation March 2005 The GBIC Standard FC PI 2 and IEEE 802 3 do not specify an 80km single mode XI interface The FTL 1519 3D complies with these standards expect for the following optical parameters laser wavelength receiver sensitivity and transmit output power See Table 6 for details For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale CA 94089 1133 Tel 1 408 548 1000 Fax 1 408 541 6138 sales finisar com www finisar com Finisar Corporation November 16 2007 Rev B1 Page 9
7. vember 16 2007 Rev B1 Page 3 FTL 1519 3D 80km Extended Reach GBIC Product Specification November 2007 Finisar RXLOS AventLevel 34 Bm Bos awd ff a a RX_LOS Hysteresis o RX LOS Assert Delay t_loss_on 100 usec ao eS of loss of signal to assertion of RX_LOS RX_LOS Negate Delay t_loss_off 100 usec From detection of presence of signal to negation of RX_LOS TX_DISABLE Assert Time t_off 10 usec Rising edge of TX_DISABLE to fall of output signal below 10 of nominal TX_DISABLE Negate Time vey pays Falling edge of TX_DISABLE to rise of output signal above 90 of nominal TX DISABLE Reset Time t_reset 10 usec TX_DISABLE HIGH before TX_DISABLE set LOW TX FAULT Initialize Time t_init 300 msec From power on after VCC gt 4A 5V a i D D D Table 4 Low speed signal parameters IV High Speed Electrical Interface All high speed PECL signals are AC coupled internally Data Input Voltage O Va 60 2000 PECL differential peak peak Data Output Voltage Nae o O 2000 PECL differential peak peak PECL risial ts 260 psec 20 80 differential BiEnorkae Ber fio PRBS 2 1 test data patem Tx Input Impedance Zw 75 Ohm Rex Output Impedance Zu 5 om ooo Table 5 High speed electrical interface Finisar Corporation November 16 2007 Rev B1 Page 4 FTL 1519 3D 80km Extended Reach GBIC Product Specification November 2007 Finisar V Optical Parameters
Download Pdf Manuals
Related Search