ARGO BLUES space heater
Contents
1. appliance outdoors WARNING do not use the convector with a controller or any other external device that activates the appliance automatically as there may be a risk of fire if the convector is covered or incorrectly positioned Upon initial start up the convector may emit a slight harmless smell This smell is a normal effect of the initial heating up of the internal heating elements and should not recur later on WARNING DO NOT DEPEND ON THE ON OFF BUTTON SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING OR MOVING THE CONVECTOR ALWAYS UNPLUG THE POWER CORD A convector has hot and arcing or sparkling parts inside It must not be used in potentially dangerous locations such as flammable explosive chemical laden or wet atmosphere e Do not place the convector on soft surfaces like a bed where openings may become blocked Always place the convector on a stable flat level surface when operating to avoid the chance of the convector overturning Locate the power cord so the convector or other objects are not resting on it Always unplug the convector when not in use In order to avoid accidents turn unit off if unattended e In the event of any problems abnormal noise or a strange smell switch off the appliance immediately do not attempt to repair it and take it to your local after sales service DESCRIPTION OF PARTS FRONT VIEW SIDE VIEW REAR VIEW A E C F A Delivery intake grille D Side Control panel B Fee2. set time wait 5 for the setting to be confirmed The unit will switch off automatically at the end of the programmed time stand by In order to switch it on again press the button ON OFF L Ifa TIMER is set the LED remains on ON OFF buttons Touching the ON OFF button will cause the ECO LED to light and the appliance will begin to operate in ECO mode The display will show ambient temperature Touching the button ON OFF once again the LED will show room temperature To switch off the convector completely place the on off switch in the OFF position COMFORT mode it adjusts automatically heat output and therefore energy consumption according to set temperature ECO SUP COMF CONTROL PANEL pO ON OFF switch C Timer on setting timer set TEMPERATURE button When COMFORT mode has been set touching this button will allow you to set the temperature the display will show ambient temperature and by pressing this button the desired temperature can be set between 15 and 35 C Once the desired temperature has been set wait 5 for the setting to be confirmed After 5 the display will show the ambient temperature once again This function is active only in COMFORT mode ECO SUPER COMFORT selection button ECO mode 750 W reduced power to save energy SUPER mode maximum heating power 1500W COMFORT mode automatic adjustment of heat emission according to set tempera
3. CE Ey WITH GLASS PANEL blues IP24 OPERATING INSTRUCTIONS Read the instructions carefully before installing and operating the appliance or performing maintenance operations Observe all the safety instructions failure to observe the instructions may cause accidents and or damages Store these instructions for future reference V 05 13 Ce GENERAL SAFETY INFORMATION e Use this convector only as outlined in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to people Ensure that the mains power complies with the voltage specified on the convector data plate 220 240V 50Hz This product is not a toy Children should be adequately supervised to ensure that they do not play with the appliance This appliance is not suitable for use by people including children with reduced physical sensory or mental abilities or without the necessary experience and knowledge unless they have been adequately supervised and instructed concerning use of the appliance by a person responsible for their safety Do not restrict the air inlet and outlet grilles e The appliance heats up slightly when in use In order to avoid burns do not let bare skin touch hot surfaces Ensure that all objects are at least 1 meter from the front and sides of the appliance Disconnect the mains power when the appliance is not used or for cleaning operations Avoid using the convector in dusty environment
4. nic equipment X separately avoids possible negative effects on the environment and human health deriving from an inappropriate disposal and enables its components to be recovered and recycled to obtain significant savings in energy and resources In order to underline the duty to dispose of this equipment separately the product is marked with a crossed out dustbin www argoclima com V 05 13 15
5. o the wall mark on the 5 Drill holes in the wall and insert the 4 Fishers wall with a pencil the points where it is necessary to Secure the bracket to the wall and insert the 4 make the holes in order to insert the Fishers Observe screws supplied the minimum distances from the walls as pointed out in the picture below 6 Place the unit upright Insert the two lower parts of the 7 Insert the two upper parts of the bracket into the bracket into the holes on the rear of the convector in the holes on the rear of the convector in the upper lower part part maa _ 8 Tighten the screws at the top of the convector firmly 9 Installation complete cS gt V 05 13 13 HOW TO USE THE CONVECTOR Connect the power cord to a suitable electric socket 220 240V 50HZz ON OFF switch on the right side Bring the on off switch to the ON position When the appliance emits a beep this means that the convector is ready for use Bring the switch to the OFF position to switch off the convector LED DISPLAY SUPER mode maximum power 1500W ECO mode 750 W reduced power to save energy Temperature and timer display TIMER button When the appliance is operating the operating time can be set by touching this button the timer display shows a flashing 0 and pressing TIMER you can set the desired time between 0 5 and 8 hours with each touch corresponding to half and hour The display shows the
6. onvector e Do not place any objects on the cord and do not bend it It is not advisable to use extension cords as these may overheat and cause the risk of fire Do not use a single extension cord to operate multiple appliances e Do not immerse the cord plug or any other element of the appliance in water or other liquids Do not touch the plug with wet hands e Do not place the convector above or near another heat source WARNING AVOID COVERING THE CONVECTOR TO PREVENT IT FROM OVERHEATING The symbol below signals the above warning e The convector may cause the risk of fire if while in operation is covered by or comes into contact with inflammable material including curtains drapery blankets etc KEEP THE CONVECTOR AWAY FROM THESE MATERIALS e Do not connect the appliance to the mains power before it has been properly assembled and positioned e Do not run the cord under carpets Do not cover the cord with blankets carpets or similar materials Place the cord far away from busy areas or where it cannot be accidentally pulled out e Do not operate the convector in close proximity to bathtubs showers washbasins or pools e The appliance is equipped with an IP24 degree of protection and can be used in private bathrooms in zone 2 The convector must not be touched by people that use bath tubs and showers Zona 3 2 29 a ne E ee a j Y V 05 13 10 Do not position the convector below a socket outlet Do not operate the
7. s or in the presence of inflammable vapours e g in workshops or garages or paint vapours e Do not place anything on the appliance use the appliance to dry clothing Use the appliance in a well ventilated area Avoid placing fingers or foreign objects in the air inlet outlet grilles as this may lead to electric shock or fire and may damage the appliance To avoid the risk of fire do not block the grilles or tamper with them in any way while the convector operates e Do not use the appliance if the cord or plug are damaged If the power supply cord is damaged it must be replaced by the manufacturer dealer or a similarly qualified person so as to avoid any safety risks e Do not operate the appliance if it has fallen from a height or has suffered damage in any way Contact qualified technical personnel to examine the appliance or perform any electrical or mechanical repairs e The most common cause of overheating is the build up of dust in the appliance Remove dust deposits by unplugging the appliance and cleaning the air outlets and grilles with the aid of a vacuum cleaner e Do not use abrasive detergents for cleaning this appliance Clean the appliance with the aid of a damp not wet cloth rinsed in hot soapy water Always remove the plug from the mains socket before cleaning e To disconnect the convector push the switch to OFF and remove the plug from the socket Pull on the plug only Avoid pulling on the cord when disconnecting the c
8. t with wheels E Rear holes for wall mounting C ON OFF switch F Rear brackets for wall mounting V 05 13 11 HOW TO INSTALL THE APPLIANCE The convector can be used on the floor after assembling the feet or alternatively it can be wall mounted using the specific accessories supplied A Floor portable using how to assemble the feet with wheels supplied The convector is packed without feet These must therefore be assembled before using the appliance Assemble the feet as shown in the figure and put the convector in an upright position Position the unit on a flat stable surface and stop the wheels with the proper wheels locks before turning it on 3 Tighten the wing nuts on the feet 1 Turn the convector upside down and 2 Insert the feet The longest part must be positioned behind on loosen the wing nuts the rear the convector B Wall mounting how to assemble the rear bracket and mount the convector onto the wall The convector packaging contains all the accessories necessary for wall mounting To wall mount proceed as follows Remove the rear bracket from the back of the unit as described in the pictures below 1 Unscrew the two screws on top of the 2 2 Pull down the wall bracket by pressing downward on the vertical bars of the wall bracket top of the two vertical bars of the wall bracket Ea 3 Remove the bracket for wall mounting from the convector completely V 05 13 4 By supporting the bracket ont
9. ture ECO is the default mode WARNING THE TEMPERATURE SELECTION BUTTON IS ACTIVE ONLY IN COMFORT MODE The appliance is fitted with an anti tip up device that prevents it from operating when it detects that the product is inclined Do not position the appliance on its side or upside down V 05 13 14 REMOTE CONTROL TEMPERATURE TIMER button button ON OFF button Mode selection button ECO SUPER or COMFORT The remote control uses Lithium Manganese button cells model no CR2032 3 V compliant with Battery Directive no 2006 66 CE supplied with the remote control HOW TO INSERT REMOVE THE REMOTE CONTROL BATTERIES refer to the diagram below Open the battery cover at the rear of the remote control press and pull the cover Place the battery into the cover observing the correct polarity Insert the cover onto the remote control il mie CR2032 SOE a ee PRESSE W Battery Installation Information for correct disposal of the battery in accordance with the European Directive 2006 66 EC Please replace battery when its electricity charge is used up please do not eliminate this battery together with normal household waste It must be taken to special local community waste collection centres or to a dealer providing this service Disposing of a battery separately avoids possible negative effects on the environment and human health deriving from an inappropriate disposal and enables its components to be reco
10. vered and recycled to obtain significant savings in energy and resources In order to underline the duty to dispose of this equipment separately the battery is marked with a crossed out dustbin MAINTENANCE AND STORAGE ALWAYS UNPLUG THE APPLIANCE BEFORE CLEANING OR MAINTENANCE IMPORTANT DO NOT SUBMERGE THE CONVECTOR IN WATER Cleaning the outside surface of the appliance Turn the switch off and unplug before carrying out any maintenance work or moving the appliance Use a soft cloth to remove any dust from the convector If the convector is excessively dirty use a soft cloth moistened with water and a mild detergent at a temperature lower than 50 C Let the convector dry completely before use Do not use corrosive detergents or solvents such as petrol Do not wash the appliance with water Do not use oils chemical substances or other items to clean that may damage the surface Use a vacuum cleaner to remove dust from the air inlet outlet grilles STORAGE If the appliance is not used for prolonged periods it must be stored together with this manual in its original packaging in a cool and dry place Information for correct disposal of the product in accordance with the European Directive 2002 96 EC At the end of its working life this equipment must not be disposed of as an household waste It must be taken to special local a community waste collection centres or to a dealer providing this service Disposing of electrical and electro
Download Pdf Manuals
Related Search