Siig PORTABLE BATTERY CHARGER 7200
Contents
1. gt Portable Battery Charger 7200 Quick Installation Guide Introduction The Portable Battery Charger 7200 easily charges electronic devices while on the go including iPhone iPod iPad mobile phones PDAs portable video games MP3 players and more Key Features and Benefits High quality rechargeable Lithium polymer battery recharges easily via computer USB port with the included USB charging cable or your USB wall charger Extends mobile phonetalk time up to 40 hours up to 50 hours of video or up to 200 hours of music based on iPhone 5 actual results will vary depending on your device Compatible with any USB powered portable device Serial Number Sticker For future product return or exchange this serial number is required Please keep it for your reference Serial Number Part Number 04 0890A 1 Package Contents Portable Battery Charger 7200 USB charging cable Quick installation guide Layout LED Indicators Power Button Input Micro USB port Output USB Type A port Figure 1 Portable Battery Charger 2400 AO 7 USB Type A tip Micro USB tip Figure 2 USB Charging Cable Tips Note Tip may vary slightly from image shown LED Indicators The LEDs display the battery life charging status of the Lithium polymer battery 1 LED 25 charge 2 LEDs 50 charge 3 LEDs 75 charge 4 LEDs Fully charged Checking the Charge C2. 6 Press and hold down briefly the charger s power button until the LEDs come on to signal charging has begun If youneed to stop charging at any time simply press and hold down the charger s power button again until the LEDs go off or unplug the charging cable from the portable device Figure 6 Specifications Battery type Lithium polymer Output 5VDC Type A USB 2A Max Input 5VDC Micro USB 1 5A Max Battery capacity 7200mAh Operating temperature 4 to 104 degrees F N Warning d Do not use the charger in high temperature environments such as direct sunlight next to a fire or any other heat source Do not expose the charger to wet environments If the charger becomes wet discontinue use and dry itimmediately s Do not dismantle or open the case the charger contains no serviceable parts Opening the case will immediatly void the manufacturer warranty Do not dispose of the charger into the garbage It must be sent to a recycling center Do not use the charger if the battery appears to be leaking Avoid contact with any battery fluid as it is corrosive and may result in personal injury Blank Page Blank Page Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could
3. Lithium polymer battery is fully charged 4 LEDs will be on Figure 4 Charging Portable Devices using the included USB Charging Cable When your portable device is out of battery you can recharge it with the Portable Battery Charger 7200 easily Just make sure the Portable Battery Charger 7200 is fully charged before proceeding T Connect the USB Type A tip of the included USB charging cable to the OUTPUT port USB Type A port of the Portable Battery Charger 7200 See Figure 5 PlugtheMicro USBtipoftheincluded USBcharging cable into the Micro USB charging port of your portable device See Figure 5 Press and hold down briefly the charger s power button until the LEDs come on to signal charging has begun If youneed to stop charging at any time simply press and hold down the charger s power button again until the LEDs go off or unplug the charging cable from the portable device Figure 5 Charging Portable Devices using the Device s USB Charging Cable When your portable device is out of battery you can recharge it with the Portable Battery Charger 7200 easily Just make sure the Portable Battery Charger 7200 is fully charged before proceeding 1 Connect the USB charging cable supplied with the device to your portable device Plug the Type A USB connector of the USB charging cable supplied with the device into the OUTPUT port USB Type A port of the Portable Battery Charger 7200 See Figure
4. be just a few clicks away You can also submit questions online and a technical support analyst will promptly respond SIIG offers a 2 year manufacturer warranty with this product This warranty covers the original purchaser and guarantees the product to be free of any defects in materials or workmanship for two 2 years from the date of purchase of the product SIIG will at our discretion repair or replace with an identical product or product having similar features and functionality the product if defective in materials or workmanship This warranty gives you specific legal rights and you may also have other rights which vary from state to state Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow the steps below to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then REQUEST A PRODUCT REPLACEMENT to submit a request to SIG RMA or fax a request to 510 657 5962 Your RMA request will be processed if the product is determined to be defective an RMA number will be issued Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All accessories that came wi
5. apacity of the Lithium polymer Battery Press and hold down briefly the power button to display the status of the Lithium polymer battery The LEDs will go off automatically in 10 seconds or you can press and hold down the power button again Operating Instructions Charging the Lithium polymer Battery using a Computer 1 Connect the Micro USB tip of the included USB charging cable into the INPUT port Micro USB port ofthe Portable Battery Charger 7200 see Figure 3 Connect the USB Type A tip of the included USB charging cable to an available USB port of your desktop or notebook computer make sure the system is turned on and the charging process will begin automatically During the charging process the blinking LED will move gradually to the next LED as the battery charges When the Lithium polymer battery is fully charged 4 LEDs will be on Figure 3 Charging the Lithium polymer Battery usingan AC Adapter 1 PlugtheMicro USBtip oftheincluded USBcharging cable into the INPUT port Micro USB port ofthe Portable Battery Charger 7200 see Figure 4 Connect the USB Type A tip of the included USB charging cable to an AC power adapter not included witha5V USB Type A charging port see Figure 4 Plug the AC power adapter into a reliable power outlet and the charging process will begin automatically During the charging process the blinking LED will move gradually to the next LED as the battery charges When the
6. gh e commerce sites PRODUCT NAME Portable Battery Charger 7200 FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCCCOMPLIANCE STATEMENT This device complies with part 15 ofthe FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SUG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Phone 510 657 8688 Portable Battery Charger 7200 is a trademark of SIIG Inc SIIG and the SIIG logo are registered trademarks of SIIG Inc All other names used in this publication are for identification only and may be trademarks of their respective companies July 2013 Copyright O 2013 by SIIG Inc All rights reserved
7. th the original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e You are responsible for the cost of shipping to SIIG Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer 11 About SIIG Inc Founded in 1985 SIIG Inc is a leading manufacturer of IT connectivity solutions including Serial ATA and Ultra ATA Controllers FireWire USB and legacy I O adapters that bridge the connection between Desktop Notebook systems and external peripherals SIIG continues to grow by adding A V and Digital Signage connectivity solutions to our extensive portfolio SUG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and throu
Download Pdf Manuals
Related Search