B&B Electronics EIR-M-SC network media converter
Contents
1. Fault condition on the Fiber port The 10 100 LNK ACT and FDX COL LED s will be off Link Fault of the TX port The Media Converter A A Link Fault condition will be sensed on the FX port whenever the media converter detects a Link Fault condition on the TX port Thus the 100 LNK ACT and FDX COL LEDs of the TX port of the Media Converter A would be off The Media Converter B A Link Fault condition will be informed to the FX port of the Media Converter B Then a Link Fault condition will be sensed on the TX port of the Media Converter B whenever the Media Converter B detects a Link Fault condition on the FX port Thus the 100 LNK ACT and FDX COL LEDs of the Media Converter B would be off Link Fault of the FX Port O J poe p o Link Fault of the TX port of the Media Converter A O poe po Media Converter A Media Converter B Functional Description e Meets NEMA TS1 2 Environmental requirements such as temperature shock and vibration for traffic control equipment e Meets IEC61000 6 2 EMC Generic Standard Immunity for industrial environment e One channel media converter between 10 100BaseTx and 100BaseFx e Support 802 3 802 3u 802 3x Auto negotiation 10 100Mbps Full half duplex Auto MDI MDIX e 100BaseFX Multi mode SC or ST type Single mode EIRx Sx series 0106 2 2 Assembly Startup and Dismantling Assembly Place the media converter on the DIN rail from above using the slot Push the f2. AULT Steady Power or ports function abnormally Power and ports function normally PWR1 Steady Power on PWR stands for POWER Power off S O PWR2 Power off 10 100 100Mbps network connection 10Mbps network connection LFP Steady LFPT function enabled LFPT function disabled LNK ACT Steady Network connection established LNK stands for LINK Flashing Transmitting or receiving data ACT stands for ACTIVITY Off Neither a network connection established nor transmitting receiving data FDX COL Steady Connection in full duplex mode FDX stands for FULL DUPLEX Flashing Collision occurred COL stands for COLLISION Connection in half duplex mode DIP Switch Settings OC Fiber Forced to Full Duplex Fiber Forced to Half Duplex Ee Disable Link Down Alarm Enable Link Down Alarm 5 electronics MANUFACTURING COMPANY International Headquarters 707 Dayton Road PO Box 1040 Ottawa IL 61350 USA 815 433 5100 Fax 483 5104 www bb elec com orders bb elec com support bb elec com European Headquarters Wesitlink Commercial Park Oranmore Co Galway Ireland 353 91 792444 Fax 353 91 792445 www bb europe com orders bb europe com support bb europe com B amp B ELECTRONICS Link fault pass through Link Fault Pass Through Overview When two Media Converters are connected via their fiber ports Link Fault of the FX port A Link Fault condition will be sensed on the RJ45 port whenever the media converter detects a Link
3. B amp B ELECTRONICS PRODUCT INFORMATION Hardened Compact Media Converter This quick installation guide describes how to install and use the hardened compact Media Converter Capable of operating at temperature extremes of 34 to 74 C this is the media converter of choice for harsh environments constrained by space 10 100BaseTX and 100BaseFX Connectors 10 100BaseTX Connections Pin _ Regular Ports Uplink Port __ P 8 TNC NG Pin 8 Pin 7 TD Pin 6 Pin 5 Pin 4 TD Pin 3 RD Pin RD Fin 1 The Tx transmit port of device 1 is connected to the Rx receive port of device 2 and the Rx receive port of device 1 to the Tx transmit port of device 2 Physical Description EIRx Sx series 0106 1 2 Terminal Block and Power Inputs Terminal Block Assignment Power Input 1 10 to 48VDC Power Input 2 10 to 48VDC Earth Ground 1 The relay opens if PWR1 or PWR2 fails 2 The relay opens if the Port Link is Down When the Link Down Alarm is Enabled LED s and DIP Switch LED Status LEDs State While only one power source is required to power up the media converter two power sources offer redundancy for those mission critical applications PWR1 and PWR2 The terminals labeled Fault are connected to a dry contact The dry contact is normally closed when either power source is connected and active When no power is applied the dry contact is normally open F
4. nstallation e Front panel LED status B6B Storage Temperature 45 to 93 C Humidity 10 to 95 non condensing Emissions FCC Part 15 Class A CE EN55022 CISR22 Class A EN55024 CISPR24 Class A Standards ESD Standard IEC 61000 4 2 Radiated FRI Standards IEC 61000 4 3 Burst Standards IEC 61000 4 4 Surge Standards IEC 61000 4 5 Induced RFI Standards IEC 61000 4 6 Magnetic Field Standards IEC 61000 4 8 Voltage Dips Standards IEC 61000 4 11 Environmental Test Compliance Vibration Resistance IEC 60068 2 6 Shock IEC 60068 2 27 Free Fall IEC 60068 2 32 NEMA TS1 2 Environmental requirements for traffic control equipment electronics MANUFACTURING COMPANY International Headquarters 707 Dayton Road PO Box 1040 Ottawa IL 61350 USA 815 433 5100 Fax 433 5104 www bb elec com orders bb elec com support bb elec com European Headquarters Wesitlink Commercial Park Oranmore Co Galway Ireland 353 91 792444 Fax 353 91 792445 www bb europe com orders bb europe com support bb europe com
5. ront of the media converter toward the mounting surface until it audibly snaps into place Startup Connect the supply voltage to start up the media converter via the terminal block e Dismantling Pull out the lower edge and then remove the media switch from the DIN rail T ga Bm Specifications Applicable Standards IEEE 802 3 10BaseT IEEE 802 3u 100BaseTX amp 100BaseFX 1 TX port VX on Speed 10BaseT 10 20Mbps for half full duplex 100BaseTX FX 100 200Mbps for half full duplex Switching Method Store and Forward 14 880 148 800pps for 10 100Mbps Cable 10BaseT 2 pair UTP STP Cat 3 4 5 up to 100m 100BaseTX 2 pair UTP STP Cat 5 up to 100m 100BaseFX MMF 50 or 62 5um SMF 9 or 10um LED Indicators Per Unit PWR1 PWR2 FAULT LFP Per Port TX LNK ACT FDX COL 100 FX LNK ACT FDX COL Dimensions 2x4 3x 5 4in 5x11 x 13 6cm SC type e DIP switch for configuring link fault pass through fixed speed full half duplex and link down alarm Terminal Block 200mA 24VDC 10 48VDC 4 8W Max Operating Temperature 34C to 74 C PRODUCT INFORMATION e Store and forward mechanism e Non blocking full wire speed forwarding rate e Support broadcast storm filtering e Back pressure amp IEEE 802 x compliant flow control e Alarms for power failure by relay output e Redundant 10 48 VDC terminal block power inputs e Operating temperature ranges from 34 to 74 C e Supports DIN rail mounting i
Download Pdf Manuals
Related Search