Triplett 9325
Contents
1. Units of measure list 10 MAX MIN MAX MIN mode 11 Hz 9oy Frequency duty cycle mode T gt ms um E IE Specifications Function Range amp Resolution Accuracy of reading AC Current 600 0 AAC 2 8 8 digits 50 60Hz 1000 AAC 3 0 8 digits AC Current 600 0 AAC 5 0 10 digits 400Hz 1000 AAC 5 0 10 digits 600 0 ADC 2 8 5 digits DC Current 1000 ADC 3 0 5 digits 600 0 mVDC 0 8 2 digits 6 000 VDC DC Voltage 60 00 VDC 1 5 2 digits 600 0 VDC 6 000 AC Voltage 60 00 VAC 1 8 8 digits 50 400Hz 600 0 VAC 600 0 Q 1 0 4 digits 6 000KQ Resistance 60 00KO 1 5 2 digits 600 0KQ 6 000MQ 2 5 3 digits 60 00MQ 3 5 5 digits Capacitance 40 00nF Unspecified 400 0nF 4 000 3 reading 5 digits 40 00 400 0 4 0 reading 10 digits 4000uF 5 0 reading 10 digits Frequency 10 10kHz 1 5 reading 2 digits Sensitivity 15Vrms Temp type K probe accuracy not included 20 0 C to 760 0 C 4 0 F to1400 0 F 3 9 5 3 9 9 Clamp size Opening 1 5 40mm approx Diode Test Test current of 0 3mA typical Open circuit voltage 1 5V DC typical Continuity Check Threshold 400 Test current 0 5mA Lo2. 2 Insert the Temperature Probe into the negative COM and the V jacks making sure to observe the correct polarity 3 Select o F with the MODE button 4 Touch the Temperature Probe head to the part whose temperature you wish to measure Keep the probe touching the part under test until the reading stabilizes about 30 seconds 5 Read the temperature in the display The digital reading will indicate the proper decimal point and value WARNING To avoid electric shock be sure the thermocouple has been removed before changing to another measurement function Non Contact AC Voltage Measurements WARNING Risk of Electrocution Before use always test the Voltage Detector on a known live circuit to verify proper operation 1 Touch the probe tip to the hot conductor or insert into the hot side of the electrical outlet 2 1 AC voltage is present the detector light will illuminate NOTE The conductors in electrical cord sets are often twisted For best results rub the probe tip along a length of the cord to assure placing the tip in close proximity to the live conductor NOTE The detector is designed with high sensitivity Static electricity or other sources of energy may randomly trip the sensor MODE BUTTON To select DC ACV OHM Diode Continuity CAP MIN amp MAX Recording Button Press MIN MAX to enter MIN MAX Recording mode manual range only Select the proper range before selecting MIN MAX to ensure that the MIN
3. MAX reading will not exceed the testing range Press once to select MIN Press again to select MAX and press again release MIN MAX recording function REL BUTTON For DCA Zero amp Offset adjustment Data Hold Button To freeze the LCD meter reading press the data hold button The data hold button is located on the left side of the meter top button While data hold is active the HOLD display icon appears on the LCD Press the data hold button again to return to normal operation Note The HOLD feature will activate when the Backlight is turned on Press the HOLD key again to exit Hold RANGE BUTTON When the meter is first turned on it automatically goes into AutoRanging This automatically selects the best range for the measurements being made and is generally the best mode for most measurements For measurement situations requiring that a range be manually selected perform the following 1 Press the RANGE button The Auto Range display indicator will turn off The Manual Range display indicator will turn on 2 Press the RANGE button to step through the available ranges until you select the range you want 3 Press and hold the RANGE button for 2 seconds to exit the ManualRanging mode and return to AutoRanging Backlight Button The backlight function illuminates the display and is used when the ambient light to too low to permit viewing of the displayed readings Press the button for two seconds to turn the backlight on a
4. OL Shorted devices will indicate near and an open device will indicate OL in both polarities Red Black Black p Forwardtest Reverse test For Continuity tests if the resistance is lt 40Q a tone will sound Capacitance Measurements WARNING To avoid electric shock disconnect power to the unit under test and discharge all capacitors before taking any capacitance measurements Remove the batteries and unplug the line cords 1 et the rotary function switch to the gt 9 CAP position 2 Insert the black test lead banana plug into the negative COM jack Insert the red test lead banana plug into the positive V jack 3 Touch the test leads to the capacitor to be tested 4 Read the capacitance value in the display Frequency duty cycle Measurements electronic 1 Set the rotary function switch to V position 2 Select ACV with the MODE button 3 Press the Hz button to indicate Hz in the display 4 Insert the black lead banana plug into the negative COM jack and the red test lead banana plug into the positive Hz jack 5 Touch the test probe tips to the circuit under test 6 Read the frequency on the display 7 Press the Hz button again to indicate 9o on the display Read the of duty cycle on the display Temperature Measurements WARNING To avoid electric shock disconnect both test probes from any source of voltage before making a temperature measurement 1 Set the function switch to TEMP
5. TRIPLET T Model 9325 True RMS AC DC Clamp On Meter Instruction Manual A TRIPLETT 84 898 guy Test Equipment amp Tools 7 11 Safety International Safety Symbols A This symbol adjacent to another symbol or terminal indicates the user must refer to the manual for further information This symbol adjacent to a terminal indicates that under normal use hazardous voltages may be present BlDouble insulation SAFETY NOTES not exceed the maximum allowable input range of any function not apply voltage to meter when resistance function is selected eSet the function switch OFF when the meter is not in use WARNINGS eSet function switch to the appropriate position before measuring eWhen measuring volts do not switch to current resistance modes eWhen changing ranges using the selector switch always disconnect the test leads from the circuit under test eDo not exceed the maximum rated input limits CAUTIONS Improper use of this meter can cause damage shock injury or death Read and understand this user manual before operating the meter Always remove the test leads before replacing the battery Inspect the condition of the test leads and the meter itself for any damage before operating the meter Repair or replace any damage before use Use great care when making measurements if the voltages are greater than 25VAC rms or 35VDC These voltages are considered a shock hazard Remove the batte
6. nd press the button a second time to turn the backlight off Battery Replacement 1 Remove the one rear Phillips head screw 2 the battery compartment 3 Replace the Requires One 9V battery 4 Re assemble the meter Triplett Three Year Limited Warranty Triplett warrants instruments and test equipment manufactured by it to be free from defective material or workmanship and agrees to repair or replace such products which under normal use and service disclose the defect to be the fault of our manufacturing with no charge within three years of the date of original purchase for parts and labor If we are unable to repair or replace the product we will make a refund of the purchase price Consult the Instruction Manual for in structions regarding the proper use and servicing of instruments and test equipment Our obligation under this warranty is limited to repair ing replacing or making refund on any instrument or test equipment which proves to be defective within three years from the date of original purchase This warranty does not apply to any of our products which have been repaired or altered by unauthorized persons in any way So as in our sole judgment to injure their stability or reliabil ity or which have been subject to misuse abuse misapplication negligence accident or which have had the serial numbers altered defaced or removed Accessories including batteries and fuses not of our manufacture used with this product a
7. nge of the measured is not known select the higher range first then move to the lower range if necessary 3 Press the trigger to open jaw Fully enclose one conductorto be measured The clamp meter LCD will display the reading DC AC Voltage Measurements 1 Insert the black test lead into the negative COM terminal and the red test lead into the positive V terminal 2 Set the function switch to the V position 3 Select AC or DC with the MODE button 4 Connect the test leads in parallel to the circuit under test 5 Read the voltage measurement on the LCD display Resistance Measurements 1 Insert the black test lead into the negative COM terminal and the red test lead into the positive terminal 2 Set the function switch to the gt 3 CAP position 3 Touch the test probe tips across the circuit or component under test It is best to disconnect one side of the device under test so the rest of the circuit will not interfere with the resistance reading 4 For Resistance tests read the resistance on the LCD display Diode and Continuity Measurements 1 Insert the black test lead banana plug into the negative COM jack and the red test lead banana plug into the positive diode jack 2 Turn the rotary switch to the 9 CAP position 3 Press the MODE button until gt appears in the display 4 Touch the test probes to the diode under test Forward voltage will indicate 0 4V to 0 7V Reverse voltage will indicate
8. re not covered by this warranty To register a claim under the provisions of this warranty contact repair triplett com ALL WARRANTIES IMPLIED BY LAW ARE HEREBY LIMITED TO A PERIOD OF THREE YEARS FROM DATE OF PURCHASE AND THE PROVISIONS OF THE WARRANTY ARE EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES EX PRESSED OR IMPLIED The purchaser agrees to assume all liability for any damages and bodily injury which may result from the use or misuse of the product by the purchaser his employees or others and the remedies provided for in this warranty are expressly in lieu of any other liability Triplett may have including incidental or consequential damages Some states USA ONLY do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you No representative of Triplett Jewell Instruments or any other person is authorized to extend the liability of Triplett in connection with the sale of its products beyond the terms hereof Triplett reserves the right to discontinue models at any time or change specifications price or design without notice and without incurring any obligation This warranty gives you specific legal rights and you may have other rights which vary from state to state A TRIPLETT Test Equipment amp Tools 850 Perimeter Road Manchester NH 03103 triplett com
9. ry if the meter is to be stored for long periods Always discharge capacitors and remove power from the device under test before performing Diode Resistance or Continuity tests Voltage checks on electrical outlets can be difficult and misleading because of the uncertainty of connection to the recessed electrical contacts Other means should be used to ensure that the terminals are not live eIf the equipment is used in a manner not specified by the manufacturer the protection provided by the equipment may be impaired Input Limits Function Maximum Input A AC DC 1000A VDC V AC 1000V DC AC Frequency Resistance Diode 1000V DC AC Continuity Capacitance Test Temperature C F 1000V DC AC Meter Description 1 Current clamp 2 Non contact AC voltage indicator light 3 Clamp trigger 4 Data Hold and Backlight button 5 Rotary Function swith 6 Hz Hlod button 2 7 RANGE select button 8 Relative button 9 MIN MAX Hlod button 10 MODE select button 11 1 display 12 COM input jack 13 V QCAP TEMPHz jack 14 Battery Cover 1 AC alternating current and DC direct currrent 2 Minus sign 3 8 8 8 8 6000 count 0 to 5999 measurement reading with 61segments Analog Bargraph 4 AUTO AutoRange mode 5 REL Relative mode 6 9t Diode test mode 7 9 Audible Continuity 8 HOLD Data Hold mode 9 um VA K M Q
10. w Battery Indication is displayed Overrange Indication OL is displayed Measurements Rate 2 per second nominal Input Impedance 10MQ VDC and VAC Display 6000 counts LCD AC Current 50 400Hz AAC AC Voltage bandwidth 50 400Hz VAC Operating Temperature 41 F to 104 F 5 C to 40 C Storage Temperature 4 F to 140 F 20 C to 60 C Operating Humidity Max 80 up to 87 F 31 C decreasing linearly to 50 at 104 F 40 C Storage Humidity lt 80 Operating Altitude 7000ft 2000meters maximum Over voltage Category III 600V Battery One 9V Battery Auto OFF approx 15 minutes Dimensions Weight 232x77x39mm 271g Safety For indoor use and in accordance with Overvoltage Category II Pollution Degree 2 Category II includes local level appliance portable equipment etc with transient overvoltages less than Overvoltage Cat III Operation NOTICES Read and understand all warning and precaution statements listed in the safety section of this operation manual prior to using this meter Set the function select switch to the OFF position when the meter is not in use AC DC Current Measurements WARNING Ensure that the test leads are disconnected from the meter before making current clamp measurements 1 Set the Function switch to the 1000ADC 600ADC 1000AAC or600AAC range 2 1 the ra
Download Pdf Manuals
Related Search