Home

Lancom Systems OAP-382

image

Contents

1. remote site dependant direction dependant bandwidth dependant N N IP address mapping Extended port forwarding Network Address Translation NAT based on protocol and WAN address i e to make internal webservers accessible from WAN N N IP address mapping for translation of IP addresses or entire networks LANCOM OAP 382 Firewall Features as of LCOS 8 82 The firewall marks packets with routing tags e g for policy based routing Source routing tags for the creation of independent firewall rules for different ARF contexts Notification Quality of Service Traffic shaping fe Forward drop reject block sender address close destination port disconnect Via e mail SYSLOG or SNMP trap Dynamic bandwidth management with IP traffic shaping Bandwidth reservation DiffServ TOS Dynamic reservation of minimum and maximum bandwidths totally or connection based separate settings for send and receive directions Setting relative bandwidth limits for QoS in percent Priority queuing of packets based on DiffServ TOS fields Packet size control Automatic packet size control by fragmentation or Path Maximum Transmission Unit PMTU adjustment Layer 2 Layer 3 tagging Intrusion Prevention Automatic or fixed translation of layer 2 priority information IEEE 802 11p marked Ethernet frames to layer 3 DiffServ attributes in routing mode Translation from layer 3 to layer 2 with au
2. Depending on the existing RF conditions the throughput is multiplied with MIMO technology Two adjacent 20 MHz channels are combined to create a single 40 MHz channel Depending on the existing RF Conditions channel bonding doubles the throughput Support of coexisting accesspoints with 20 and 40MHz channels in 2 4GHz band MAC Aggregation increase the 802 11 MAC efficiency by combining MAC data frames and sending it out with a single header The receiver acknowledges the combined MAC frame with a Block Acknowledgement Depending on existing RF conditions this technique improves throughput by up to 20 Maximal Ratio Combining MRC Maximal Ratio Combining MRC enables the receiver access point in combination with multiple antennas to optimally combine MIMO signals to improve the client reception at long range Short Guard Interval BFWA The guard interval is the time between OFDM symbols in the air 802 11n gives the option for a shorter 400 nsec guard interval compared to the legacy 800 nsec guard interval Under ideal RF conditions this increases the throughput by upto 10 Support for Broadband Fixed Wireless Access in 5 8 GHz band with up to 4 Watts EIRP for WLAN point to point links according to the national regulations of your country special antennas required Note WLAN operating modes The use of BFWA is subject to country specific regulation Stateful inspection firewall WLAN access poi
3. be specified in either milliseconds seconds minutes hours or days 802 1X supplicant Rogue WLAN client detection based on probe requests __ Authentication of an access point in WLAN client mode at another access point via 802 1X EAP TLS EAP TTLS and PEAP Layer 3 Tunneling eS eee eee Layer 3 Tunneling in conformity with the CAPWAP standard allows the bridging of WLANs per SSID to a separate IP subnet Layer 2 packets are encapsulated in Layer 3 tunnels and transported to a LANCOM WLAN controller By doing this the access point is independent of the present infrastructure of the network Possible applications are roaming without changing the IP address and compounding SSIDs without using VLANs IEEE 802 11n Features MIMO 40 MHz Channels 20 40MHz Coexistence Mechanisms in the 2 4GHz Band MAC Aggregation and Block Acknowledgement IEEE 802 11u The WLAN standard IEEE 802 11u Hotspot 2 0 allows for a seamless transition from the cellular network into WLAN hotspots Authentication methods using SIM card information certificates or username and password enable an automatic encrypted login to WLAN hotspots without the need to manually enter login credentials Note The effective distances and transmission rates that can be achieved are depending of the site RF conditions MIMO technology is a technique which uses multiple transmitters to deliver multiple data streams via different spatial channels
4. operating and monitoring of WLAN networks except for P2P connections Extensive Ethernet IP and DNS statistics SYSLOG error counter Connection time online time transfer volumes per station Snapshot function for regular read out of values at the end of a billing period Timed CRON command to reset all counters at once LAN COM OAP 3 82 Features as of LCOS 8 82 Statistics Accounting information exportable via LANmonitor and SYSLOG Hardware Power supply Via Power over Ethernet max distance between access point injector and switch 50 m 1 x PoE Injector supplied Power supply 1 x 48 V DC with optional 48V cable not included in delivery Environment 25 C to 50 C at 95 max humidity non condensing Housing 235 mm x 210 mm x 80 mm W x H x D 3 4 kg robust metal housing IP 66 protection rating ready for wall and pole mounting 6 LEDs for status display Power consumption max 37 Watts when heating is active 27 Watts when heating is not active PoE operates with the supplied PoE adapter only Declarations of conformity EN 60950 1 EN 301 489 1 EN 301 489 17 2 4 GHz WLAN EN 300 328 5 GHz WLAN EN 301 893 EN 302 502 Notifications Certifications notified in Germany Belgium Netherlands Luxembourg Austria Switzerland UK Italy Spain France Portugal Czech Republic Denmark IPv6 IPv6 Ready Gold You will find all declarations of conformity in the products section of o
5. roll out management Commands for live Telnet session scripts or CRON jobs HTTPS Client authentication possible by username and password or by certificate SSH amp Telnet client HTTPS Server Large Scale Monitor LSM m SSA SSH client function compatible to Open SSH under Linux and Unix operating systems for accessing third party components from a LANCOM router Also usable when working with SSH to login to the LANCOM device Support for certificate and password based authentication Generates its own key with sshkeygen SSH client functions are restricted to administrators with appropriate rights Telnet client function to login administer third party devices or other LANCOM devices from command line interface Option to choose if an uploaded certificate or the default certificate is used by the HTTPS server The LANCOM Large Scale Monitor LSM is a professional tool for monitoring medium sized to large scale networks with 25 to 1 000 network components Designed especially for LANCOM components including WLAN access points controllers switches and routers this system based on open source components additionally allows for the monitoring of third party products such as servers and printers Problems in the network are clearly displayed in tables or graphical floor plans and they trigger alert messages via e mail if certain threshold values are not maintained Lo Security Access rights read write over WAN or W LAN
6. with project or customer specific settings Up to two boot and reset persistent memory spaces can store customized configurations for customer specific standard settings memory space 1 or as a rollout configuration memory space 2 A further option is the storage of a persistent standard certificate for the authentication of connections during rollouts Device Syslog User administration Access rights Individual access and function rights for up to 16 administrators Alternative access control on a per parameter basis with TACACS Syslog buffer in the RAM size depending on device memory to store events for diagnosis Default set of rules for the event protocol in Syslog The rules can be modified by the administrator Display and saving of internal Syslog buffer events from LANCOM devices with LANmonitor display only with WEBconfig RADIUS user administration for dial in access PPP PPTP Support for RADSEC Secure RADIUS providing secure communication with RADIUS servers Remote maintenance TACACS Remote maintenance of 3rd party devices T Remote configuration with Telnet SSL SSH with password or public key browser HTTP HTTPS TFTP or SNMP firmware upload via HTTP HTTPS or TFTP Support of TACACS protocol for authentication authorization and accounting AAA with reliable connections and encrypted payload Authentication and authorization are separated completely LANCOM access rights are converted to TACA
7. 64 WEP128 WEP152 user authentication 802 1x EAP LEPS WPA1 TKIP EAP Types EAP TLS EAP TTLS MSCHAPv2 PEAPv0 EAP MSCHAPv2 PEAPv1 EAP GTC EAP SIM EAP AKA EAP AKA Prime EAP FAST RADIUS server Integrated RADIUS server for MAC address list management EAP server Integrated EAP server for authentication of 802 1X clients via EAP TLS EAP TTLS PEAP MSCHAP or MSCHAPv2 Quality of Service Prioritization according to Wireless Multimedia Extensions WME subset of IEEE 802 11e LANCOM OAP 382 U APSD WMM Power Save Features as of LCOS 8 82 Extension of power saving according to IEEE 802 11e by Unscheduled Automatic Power Save Delivery equivalent to WMM Power Save U APSD supports the automatic switch of clients to a doze mode Increasmed battery lifetime for telephone calls over VOWLAN Voice over WLAN Bandwidth limitation Broken link detection Maximum transmit and receive rates and an individual VLAN ID can be assigned to each WLAN client MAC address If the link of a chosen LAN interface breaks down a WLAN module can be deactivated to let the associated clients search for a new base station Background scanning Client detection Detection of rogue AP s and the channel information for all WLAN channels during normal AP operation The Background Scan Time Interval defines the time slots in which an AP or Router searches for a foreign WLAN network in its vicinity The time interval can
8. ANCOM fiber kit and the LANCOM OAP 380 PSU More flexibility The LANCOM OAP 382 can be networked via Ethernet or fiber optics The externally accessible SFP slot provides a variety of options for implementing the fiber optic connection The device also offers versatility in the choice of power supply Depending on the local situation the LANCOM 382 OAP can be powered either by the supplied Gigabit High Power PoE injector or via an optionally available 48V cable More security LANCOM ensures the highest security standards as it supports a comprehensive range of encryption and authentication mechanisms including 802 11i 802 1x and WPA2 With the aid of Multi SSID and protocol filters up to 8 different user groups can each be assigned with different levels of security VLAN technology matured quality of service functions and bandwidth limitation enable the reliable transmission of video and multimedia data More management A management system is vital outdoors where conditions are difficult for example when it is hard to see the LEDs on an access point mounted on a tall mast The free LCMS LANCOM Management System allows the monitoring of all device functions and provides an overview of the entire network For example it is possible to check whether the access points are transmitting and if so on which channels how much data each one is sending which clients are logged in and where what encryption method is active and a whole lot mor
9. CS levels With TACACS access can be granted per parameter path command or functionality for LANconfig WEBconfig or Telnet SSH Each access and all changes of configuration are logged Access verification and logging of SNMP Get and Set requests WEBconfig supports the access rights of TACACS and choice of TACACS server at login LANconfig provides a device login with the TACACS request conveyed by the addressed device Authorization to execute scripts and each command within them by checking the TACACS server s database CRON action table and script processing can be diverted to avoid TACACS to relieve TACACS servers Redundancy by setting several alternative TACACS servers Configurable option to fall back to local user accounts in case of connection drops to the TACACS servers Compatibility mode to support several free TACACS implementations A remote configuration for devices behind der LANCOM can be accomplished after authentication via tunneling of arbitrary TCP based protocols e g for HTTP S remote maintenance of VoIP phones or printers of the LAN Additionally SSH and Telnet client allow to access other devices from a LANCOM device with an interface to the target subnet if the LANCOM device can be reached at its command line interface TFTP amp HTTP S client For downloading firmware and configuration files from a TFTP HTTP or HTTPS server with variable file names wildcards for name MAC IP address serial number e g for
10. IPv6 compatible LCOS applications WEBconfig HTTP HTTPS SSH Telnet DNS TFTP Firewall WAN protocols Ethernet PPPoE Multi PPPoE ML PPP PPTP PAC or PNS and IPoE with or without DHCP RIP 1 RIP 2 VLAN IP IPv6 IPv6 over PPP IPv6 and IPv4 IPv6 dual stack session IPoE autoconfiguration DHCPv6 or static Tunneling protocols IPv4 1Pv6 6to4 6in4 6rd static and via DHCP WAN operating mode xDSL ext modem ADSL1 ADSL2 or ADSL2 with external ADSL2 modem Interfaces Ethernet port 1 Gigabit Ethernet Port 10 100 1000 Mbit s High Power PoE 56V with supplied PoE Injector only SFP Slot Harting SFP Slot HAN 3A SFP for pluggable SFP module copper SFP modules are not supported SFP module and fiber cable not included in delivery External antenna connectors Four N connectors for external LANCOM AirLancer Extender antennas or for antennas from other vendors Please respect the restrictions which apply in your country when setting up an antenna system For information about calculating the correct antenna setup please refer to www lancom systems com LCMS LANCOM Management System LANconfig Configuration program for Microsoft Windows incl convenient Setup Wizards Optional group configuration simultaneous remote configuration and management of multiple devices over IP connection HTTPS HTTP TFTP A tree view of the setting pages like in WEBconfig provides quick access to all settings in the configurati
11. Power ETH WLAN WLAN2 SFP Message LANCOM OAP 382 Dual radio 802 11n outdoor access point with fiber optic connector for maximum performance Two integrated 300 Mbps wireless modules for simultaneous operations with IEEE 802 11a b g n Versatility from fiber optic connector and Gigabit Ethernet Power over Ethernet for easy installation away from power supplies Optional external 48V power supply Professional management functions IEEE 802 11i WPA2 Multi SSID and VLAN Robust IP 66 protective housing Integrated heating and cooling ensures reliability even at extreme temperatures 25 C to 50 C LANCOM Systems The LANCOM OAP 382 outdoor access point is the right choice for anybody taking high speed 802 11n wireless LAN to outdoor areas Its two radio modules make this access point suitable for a wide range of applications For example it can operate as a relay station in a link to a backbone while simultaneously providing Internet access for WLAN clients With its water jet resistant IP 66 housing integrated heating and cooling and the sturdy fittings for wall and pole mounting the device can be operated wherever the highest standards for stability and robustness apply be it in the mountains or from rooftop to rooftop in the city The LANCOM OAP 382 can be easily and economically mounted up to 50 m from the nearest power supply thanks to Power over Ethernet In case you have longer distances you are recommended to use the L
12. between multiple active devices including load balancing and user definable backup priorities FirmSafe For completely safe software upgrades thanks to two stored firmware versions incl test mode for firmware updates Routing functions IP and NetBIOS IP multi protocol router j Line monitoring with LCP echo monitoring dead peer detection and up to 4 addresses for end to end monitoring with ICMP polling Advanced Routing and Forwarding Separate processing of 16 contexts due to virtualization of the routers Mapping to VLANs and complete independent management and configuration of IP networks in the device i e individual settings for DHCP DNS Firewalling QoS VLAN Routing etc Automatic learning of routing tags for ARF contexts from the routing table HTTP HTTP and HTTPS server for configuration by web interface DNS DNS client DNS server DNS relay DNS proxy and dynamic DNS client DHCP DHCP client DHCP relay and DHCP server with autodetection Cluster of several LANCOM DHCP servers per context ARF network enables caching of all DNS assignments at each router DHCP forwarding to multiple redundant DHCP servers NetBIOS NetBIOS IP proxy NTP NTP client and SNTP server automatic adjustment for daylight saving time Policy based routing Dynamic routing Policy based routing based on routing tags Based on firewall rules certain data types are marked for specific routing e g to particular
13. can be set up separately Telnet SSL SSH SNMP HTTPS HTTP access control list Scriptin Scripting function for batch programming of all command line parameters and for transferring partial configurations irrespective of software pting pting prog g p g p g p Load commands LoadFirmware LoadConfig and LoadScript can be executed conditionally in case certain requirements are met For example the command versions and device types incl test mode for parameter changes Utilization of timed control CRON or connection establishment and termination to run scripts for automation Scripts can send e mails with various command line outputs as attachments LoadFirmware could be executed on a daily basis and check each time if the current firmware is up to date or if a new version is available In addition LoadFile allows the upload of files including certificates and secured PKCS 12 containers SNMP Timed control SNMP management via SNMPv2 private MIB exportable by WEBconfig MIB II Scheduled control of parameters and actions with CRON service Diagnosis LANCOM WLAN Controller Statistics Accounting Extensive LOG and TRACE options PING and TRACEROUTE for checking connections LANmonitor status display internal logging buffer for SYSLOG and firewall events monitor mode for Ethernet ports Supported by all LANCOM WLAN Controller separate optional hardware equipment for installation optimization
14. denauerstr 20 B2 52146 Wuerselen Germany E Mail info lancom eu Internet www lancom eu LANCOM Systems LANCOM LANCOM Systems and LCOS are registered trademarks All other names or descriptions used may be trademarks or registered trademarks of their owners Subject to change without notice No liability for technical errors and or omissions 8 2013
15. e The LANCOM Management System also helps you to optimize performance over wireless bridges Additionally the LANCOM OAP 382 supports TACACS Using the AAA protocol authentication authorization accounting it is possible to track all activities relating to the configuration of the access point More reliability for the future LANCOM products are fundamentally designed for a product life spanning several years They are equipped with hardware dimensioned for the future Even reaching back to older product generations updates to the LANCOM Operating System LCOS are available several times a year free of charge and offering major features LANCOM OAP 382 Frequency band 2 4 GHz and 5 GHz Features as of LCOS 8 82 2400 2483 5 MHz ISM and 5150 5825 MHz depending on country specific restrictions Data rates 802 11b g 54 Mbps to IEEE 802 11g fallback to 48 36 24 18 12 9 6 Mbps Automatic Rate Selection compatible to IEEE 802 11b 11 5 5 2 1 Mbps Automatic Rate Selection 802 11 b g compatibility mode or pure g or pure b Data rates 802 11a h 54 Mbps fallback to 48 36 24 18 12 9 6 Mbps Automatic Rate Selection fully compatible with TPC adjustable power output and DFS automatic channel selection radar detection according to EN 301 893 and EN 302 502 Range outdoor P2P More than 20 km in 5 GHz See our LANCOM Antenna Distance Calculator under www lancom de Output power at rad
16. eiver sensitivity 2 4 GHz 802 11b 91 dBm 11 Mbps 96 dBm 1 Mbps 802 119 96 dBm 6 Mbps 83 dBm 54 Mbps 802 11n 96 dBm 6 5 Mbps MCSO 20 MHz 79 dBm 65 Mbps MCS7 20 MHz 93 dBm 13 Mbps MCS8 20 MHz 77 dBm 130 Mbps MCS15 20 MHz 90 dBm 15 Mbps MCSO 40 MHz 75 dBm 150 Mbps MCS7 40 MHz 90 dBm 30 Mbps MCS8 40 MHz 73 dBm 300 Mbps MCS15 40 MHz Receiver sensitivity 5 GHz 802 1 1a h 95 dBm 6 Mbps 82 dBm 54 Mbps 802 11n 95 dBm 6 5 Mbps MCSO 20 MHz 77 dBm 65 Mbps MCS7 20 MHz 94 dBm 13 Mbps MCS8 20 MHz 74 dBm 130 Mbps MCS15 20 MHz 91 dBm 15 Mbps MCSO 40 MHz 75 dBm 150 Mbps MCS7 40 MHz 90 dBm 30 Mbps MCS8 40 MHz 71 dBm 300 Mbps MCS15 40 MHz Receiver sensitivity 2 4 GHz WLAN 2 802 11b 90 dBm 11 Mbps 802 11g 76 dBm 54 Mbps 802 11n 70 dBm 65 Mbps MCS7 20 MHz 70 dBm 150 Mbps MCS7 40 MHz Receiver sensitivity 5 GHz WLAN 2 802 1 1a h 76 dBm 54 Mbps 802 11n 69 dBm 65 Mbps MCS7 20 MHz 68 dBm 150 Mbps MCS7 40 MHz Radio channels 2 4 GHz Up to 13 channels max 3 non overlapping depending on country specific restrictions Radio channels 5 GHz Up to 26 non overlapping channels available channels and further obligations such as automatic DFS dynamic channel selection depending on national regulations Band Steering Steering of WLAN clients towards the 5 GHz frequ
17. ency band by restricting the access to the 2 4 GHz band Roaming Seamless handover between radio cells APP support with optional restriction to an ARF context IEEE 802 11d support WPA2 fast roaming Pre authentication and PMK caching for fast roaming Fast client roaming With background scanning moving LANCOM client mode access points pre authenticate to alternative access points which offer a better signal before Roaming fails VLAN VLAN ID definable per interface WLAN SSID point to point connection and routing context 4094 IDs IEEE 802 1q Dynamic VLAN assignment Dynamic VLAN assignment for target user groups based on MAC addresses BSSID or SSID by means of external RADIUS server Q in Q tagging Support of layered 802 1Q VLANs double tagging Multi SSID Simultaneous use of up to 8 independent WLAN networks per WLAN interface IGMP snooping Support for Internet Group Management Protocol IGMP in the WLAN bridge for WLAN SSIDs and LAN interfaces for specific switching of multicast packets devices with integrated WLAN only Automated detection of multicast groups Configurable action for multicast packets without registration Configuration of static multicast group members per VLAN ID Configuration of query simulation for multicast membership per VLAN ID Security IEEE 802 111 WPA2 with passphrase WPA2 Personal or 802 1X WPA2 Enterprise and hardware accelerated AES closed network WEP
18. io module 2 4 GHz 802 11b 19 dBm 1 and 2 Mbps 19 dBm 5 5 und 11 Mbps 802 119 18 dBm 6 to 36 Mbps 17 dBm 48 Mbps 16 dBm 54 Mbps 802 11n 19 dBm 6 5 13 Mbps MCS0 8 20 MHz 10 dBm 65 130 Mbps MCS7 15 20 MHz 17 dBm 15 30 Mbps MCS0 8 40 MHz 10 dBm 150 300 Mbps MCS7 15 40 MHz Output power at radio module 5 GHz 802 11a h 18 dBm 6 to 24 Mbps 17 dBm 36 Mbps 16 dBm 48 Mbps 15 dBm 54 Mbps 802 11n 18 dBm 6 5 13 Mbps MCS0 8 20 MHz 10 dBm 65 130 Mbps MCS7 15 20 MHz 17 dBm 15 30 Mbps MCS0 8 40 MHz 10 dBm 150 300 Mbps MCS7 15 40 MHz Output power at radio module 2 4 GHz WLAN 2 Output power at radio module 5 GHz WLAN 2 802 11b 18 dBm 1 and 2 Mbps 18 dBm 5 5 and 11 Mbps 802 11g 16 dBm 54 Mbps 802 11n 15 dBm 65 130 Mbps MCS7 20 MHz 15 dBm 150 300 Mbps MCS7 40 MHz 802 1 1a h 12 dBm 54 Mbps 802 11n 12 dBm 65 130 Mbps MCS7 20 MHz 12 dBm 150 300 Mbps MCS7 40 MHz Max radiated power EIRP 2 4 GHz band 802 11b g Up to 20 dBm 100 mW EIRP transmission power control according to TPC Max radiated power EIRP 5 GHz band 802 11a h Up to 30 dBm 1000 mW or up to 36 dBm 4000 mW EIRP depending on national regulations on channel usage and subject to further obligations such as TPC and DFS Minimum transmission power Transmission power reduction in software in 1 dB steps to min 0 5 dBm Rec
19. l management of 25 opt up to 100 LANCOM access points and WLAN routers item no 61378 item no Art Nr 61379 and item no 61384 US LANCOM WLC 4025 EU UK LANCOM WLAN controller for central management of 25 opt up to 100 LANCOM access points and WLAN routers item no 61550 EU and item no 61551 UK only stock devices article is no longer available LANCOM WLC 4100 EU UK LANCOM WLAN controller for central management of 100 opt up to 1000 LANCOM access points and WLAN routers item no 61369 EU and item no 61377 UK External antenna AirLancer Extender 0 30 2 4 GHz outdoor antenna item no 60478 External antenna AirLancer Extender 0 70 2 4 GHz outdoor antenna item no 60469 External antenna AirLancer Extender O 9a 5 GHz outdoor antenna item no 61220 LANCOM OAP Accessories External antenna External antenna 382 irLancer Extender 0 18a 5 GHz outdoor antenna item no 61210 AirLancer Extender O D80g 2 4 GHz dual linear polarisation diversity outdoor sector antenna item no 61221 Features as of LCOS 8 82 External antenna AirLancer Extender O D60a 5 GHz dual linear polarisation diversity outdoor sector antenna item no 61222 External antenna External antenna AirLancer Extender 0 360ag dual band omnidirectional outdoor antenna item no 61223 AirLancer Extender O D9a 5 GHz dual linear polarisation diversity outdoor antenna item n
20. nd Rogue Client visualization LANCOM QuickFinder as search filter that reduces the view to devices with matching properties Firewall GUI Graphical user interface for configuring the object oriented firewall in LANconfig Tabular presentation with symbols for rapid understanding of objects choice of symbols for objects objects for actions Quality of Service remote sites services default objects for common scenarios individual object definition e g for user groups Automatic software update Voluntary automatic updates for LCMS Search online for LCOS updates for devices managed by LANconfig on the myLANCOM download server myLANCOM account mandatory Updates can be applied directly after the download or at a later time LANCOM OAP 382 ETE WEBconfig LANCOM Layer 2 Management emergency management Features as of LCOS 8 82 Integrated web server for the configuration of LANCOM devices via Internet browsers with HTTPS or HTTP Similar to LANconfig with a system overview syslog and events display symbols in the menu tree quick access with side tabs WEBconfig also features Wizards for basic configuration security Internet access LAN LAN coupling Online help for parameters in LCOS menu tree The LANCOM Layer 2 Management protocol LL2M enables an encrypted access to the command line interface of a LANCOM device directly via a Layer 2 connection Alternative boot configuration During rollout devices can be preset
21. nt Infrastructure mode autonomous operation or managed by LANCOM WLAN Controller WLAN bridge Point to multipoint connection of up to 16 Ethernet LANs mixed operation optional broken link detection blind mode supports VLAN When configuring Pt to Pt links pre configured names can be used as an alternative to MAC Adresses for creating a link Rapid spanning tree protocol to support redundant routes in Ethernet networks WLAN router Use of the LAN connector for simultaneous DSL over LAN IP router NAT Reverse NAT IP masquerading DHCP server DHCP client DHCP relay server DNS server PPPoE client incl Multi PPPoE PPTP client and server NetBIOS proxy DynDNS client NTP port mapping policy based routing based on routing tags tagging based on firewall rules dynamic routing with RIPv2 VRRP WLAN client Transparent WLAN client mode for wireless Ethernet extensions e g connecting PCs or printers by Ethernet up to 64 MAC addresses Automatic selection of a WLAN profile max 8 with individual access parameters depending on signal strength or priority Incoming Outgoing Traffic inspection based on connection information Trigger for firewall rules depending on backup status e g simplified rule sets for low bandwidth backup lines Limitation of the number of sessions per remote site ID Packet filter Check based on the header information of an IP packet IP or MAC source destination addresses source destination ports DiffServ attribute
22. o 61224 1000Base SX SFP module LANCOM SFP SX LC2 item no 61558 Antenna cable AirLancer cable NJ NP 3m antenna cable extension for connection with LANCOM outdoor antennas item no 61230 Antenna cable AirLancer cable NJ NP 6m antenna cable extension for connection with LANCOM outdoor antennas item no 61231 Antenna cable AirLancer cable NJ NP 9m antenna cable extension for connection with LANCOM outdoor antennas item no 61232 Surge arrestor antenna cable AirLancer Extender SA 5L surge arrestor 2 4 and 5 GHz to be integrated between Access Point and antenna item no 61553 Surge arrestor LAN cable AirLancer Extender SA LAN surge arrestor LAN cable item no 61213 LAN cable outdoor LANCOM OAP 380 Ethernet cable 15 m item no 61508 LAN cable outdoor Multimode Fiber Kit LANCOM OAP 380 Ethernet cable 30 m item no 61348 LANCOM OAP 380 Multimode Fiber Kit item no 61546 Power Cable Outdoor LANCOM OAP 380 Power Cable 15 m item no 61545 Power Supply Unit Outdoor LANCOM OAP 380 PSU 48 V DC Outdoor Power Supply for OAP 382 230 V AC Note Item number s The Polarization Diversity antennas require 2 cables and surge arrestors LANCOM OAP 382 EU 61542 LANCOM OAP 382 UK 61561 LANCOM OAP 382 bulk 1 excluding cable 61544 antennas and power supply www lancom eu LANCOM Systems GmbH A
23. on window Password fields which optionally display the password in plain text and can generate complex passwords Configuration program properties per project or user Automatic storage of the current configuration before firmware updates Exchange of configuration files between similar devices e g for migrating existing configurations to new LANCOM products Detection and display of the LANCOM managed switches Extensive application help for LANconfig and parameter help for device configuration LANCOM QuickFinder as search filter within LANconfig and device configurations that reduces the view to devices with matching properties LANmonitor Monitoring application for Microsoft Windows for remote surveillance and logging of the status of LANCOM devices and connections incl PING diagnosis and TRACE with filters and save to file Search function within TRACE tasks Wizards for standard diagnostics Export of diagnostic files for support purposes including bootlog sysinfo and device configuration without passwords Graphic display of key values marked with an icon in LANmonitor view over time as well as table for minimum maximum and average in a separate window e g for Rx Tx CPU load free memory Monitoring of the LANCOM managed switches Flick easily through different search results by LANCOM QuickFinder WLANmonitor Monitoring application for Microsoft Windows for the visualization and monitoring of LANCOM WLAN installations incl Rogue AP a
24. remote sites or lines Dynamic routing with RIPv2 Learning and propagating routes separate settings for LAN and WAN Extended RIPv2 including HopCount Poisoned Reverse Triggered Update for LAN acc to RFC 2453 and WAN acc to RFC 2091 as well as filter options for propagation of routes Definition of RIP sources with wildcards LAN COM OAP 3 82 Features as of LCOS 8 82 Routing functions DHCPv6 DHCPv6 client DHCPv6 server DHCPv6 relay stateless and stateful mode IPv6 address IA_NA prefix delegation IA_PD DHCPv6 reconfigure server and client Layer 2 functions ARP lookup Packets sent in response to LCOS service requests e g for Telnet SSH SNTP SMTP HTTP S SNMP etc via Ethernet can be routed directly to the requesting station default or to a target determined by ARP lookup LLDP Automatic discovery of network topology in layer 2 networks Link Layer Discover Protocol LAN protocols IP ARP proxy ARP BOOTP DHCP DNS HTTP HTTPS IP ICMP NTP SNTP NetBIOS PPPoE server RADIUS RIP 1 RIP 2 RTP SIP SNMP TCP TFTP UDP VRRP VLAN Rapid Spanning Tree 802 1d Spanning Tree and 802 1w Rapid Spanning Tree support for dynamic path selection with redundant layer 2 connections IPv6 NDP stateless address autoconfiguration SLAAC stateful address autoconfiguration with DHCPv6 router advertisements ICMPv6 DHCPv6 DNS HTTP HTTPS PPPoE TCP UDP IPv6 Dual Stack IPv4 IPv6 dual stack
25. tomatic recognition of 802 11p support in the destination device Monitoring and blocking of login attempts and port scans IP spoofing iaa Access control lists Source IP address check on all interfaces only IP addresses belonging to the defined IP networks are allowed Filtering of IP or MAC addresses and preset protocols for configuration access Denial of Service protection General Ig Protection from fragmentation errors and SYN flooding Detailed settings for handling reassembly PING stealth mode and AUTH port URL blocker Filtering of unwanted URLs based on DNS hitlists and wildcard filters Password protection Alerts i Password protected configuration access can be set for each interface Alerts via e mail SNMP Traps and SYSLOG Authentication mechanisms EAP TLS EAP TTLS PEAP MS CHAP MS CHAPv2 as EAP authentication mechanisms PAP CHAP MS CHAP and MS CHAPv2 as PPP authentication mechanisms WLAN protocol filters Limitation of the allowed transfer protocols source and target addresses on the WLAN interface oS ee IP redirect High availability redundancy Fixed redirection of any packet received over the WLAN interface to a dedicated target address Line monitoring Router VRRP VRRP Virtual Router Redundancy Protocol for backup in case of failure of a device or remote station Enables passive standby groups or reciprocal backup
26. ur website at www lancom systems eu Scope of delivery Manual Hardware Quick Reference EN DE Installation Guide DE EN FR ES IT PT NL CD DVD Data medium with management software LANconfig LANmonitor WLANmonitor LANCAPI and documentation Water resistant UV resistant Ethernet PoE cable with water resistant screw connector 15m AirLancer Adapter NP NP 25 cm connector for external LANCOM outdoor antennas Four 3 dBi dipole dual band antennas Power supply unit Via Power over Ethernet 1 x Gigabit High Power PoE 50W 56V Injector supplied Note Power over Etherner operates with the supplied PoE adapter only Support 3 years Support via Hotline and Internet KnowledgeBase Software updates Regular free updates LCOS operating system and LANCOM Management System via Internet Options Advance Replacement LANCOM Next Business Day Service Extension IAP amp OAP item no 61412 Warranty Extension LANCOM 2 Year Warranty Extension IAP amp OAP item no 61415 Public Spot LANCOM Public Spot Option authentication and accounting software for hotspots incl Voucher printing through Standard PC printer item no 60642 Accessories LANCOM WLC 4006 EU UK US LANCOM WLAN controller for central management of 6 opt up to 30 LANCOM access points and WLAN routers item no 62035 EU item no 62036 UK and item no 62037 US LANCOM WLC 4025 EU UK US LANCOM WLAN controller for centra

Download Pdf Manuals

image

Related Search

Related Contents

900557-001 Remote Control-LOW-BATTERY-INCLUDED  manual de instalación disp-mag 2009  User`s Manual for Genair - utoronto-comp-aero  CD3000S-2PH Thyristor Unit - West Instruments de México, SA  PERIOD A Time-Series Analysis Package  THE ISSUES User Manual  Toshiba ZT170F (T170F)  Table des matières  ENERGY SAVERS TIPS FOR ALASKA  「取扱説明書」 EALシリーズ  

Copyright © All rights reserved.
Failed to retrieve file