Finisar FTL-8519-3D network transceiver module
Contents
1. Note Vig and Vj are the same for both 5V and 3 3V operation Table 3 Low speed signals electronic characteristics Finisar Corporation November 16 2007 Rev A4 Page 3 FTL 8519 3D GBIC Product Specification November 2007 Finisar Low Speed Signal Parameters ee ee ee eS RXLOS Aven Level 30 am SSCS RX LOS Deassert Level 19 apm S RX_LOS Hysteresis Jo janj SSS From detection of loss of signal to assertion of RX_LOS RX_LOS Assert Delay t_loss_on RX_LOS Negate Delay t_loss_of TX_DISABLE Assert Time _ off _ off TX_DISABLE Negate Time t_on 90 of nominal TX_DISABLE Reset Time t_reset usec TX_DISABLE HIGH before TX_DISABLE set LOW Table 4 Low speed signal parameters ae 44 100 usec From detection of presence of signal to negation of RX_LOS 10 usec Rising edge of TX_DISABLE to fall of output signal below 10 of nominal a 1000 usec Falling edge of TX_DISABLE to rise of output signal above IV High Speed Electrical Interface All high speed PECL signals are AC coupled internally Symbol Notes Conditions Data Input Voltage Va 650 2000 PECL differential peak peak ata Ouipot Voltage Vou 370 2000 mV PECL differential peak peak ie 2 pee porso different Bit EmorRate Be o PRBS 2 1 test daa panem A Z mm TT Powie Zan a SS Table 5 High speed electrical interface Finisar Corporation November 16 2007 Rev A2. 0 tested in production Power tested at room temp to 2 dB Range Internal Transceiver DD Temperature 40 100 C Temperature Internal Transceiver DD otiage 3 0 6 0 V Supply Voltage Tx Bias Current DDgias 0 15 mA Tx Output Power DD py Power 12 2 dBm Received Average DDaxpower 20 1 dBm Power Table 9 Digital Diagnostic Accuracy and Range Limits X Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5 5 Section 61 Retention Forces Min 20 Newtons 45lbs SSCS s Newtons 33lbs iS z ma Table 10 Insertion extraction and retention forces GBIC insertion F GBIC extraction F GBIC retention F Finisar Corporation November 16 2007 Rev A4 Page 7 FTL 8519 3D GBIC Product Specification November 2007 Finisar 1 031 Figure 1 GBIC Outline Drawing Finisar Corporation November 16 2007 Rev A4 Page 8 FTL 8519 3D GBIC Product Specification November 2007 Finisar XI References 1 XI Gigabit Interface Converter GBIC Revision 5 5 Sun Microsystems Computer Company et al September 27 2000 http playground sun com pub OEmod IEEE Std 802 3 IEEE Standards Department 2002 Fibre Channel Physical and Signaling Interface FC PH FC PH2 FC PH3 American National Standard for Information Systems Fibre Channel Draft Physical Interface Specificat
3. 4 Page 4 FTL 8519 3D GBIC Product Specification November 2007 Finisar V Optical Parameters Optical Parameters Conforms to IEEE 802 3 and Fibre Channel Eye Masks Total Transmitter Jitter Transmitter Rise Fall Time Optical Input Wavelength Optical Receiver Sensitivity 2 1 test data pattern 1 25Gb s Average Received Power Max Reflectivity Total Receiver Jitter Table 6 Optical parameters VI General Specifications General Symbol Notes Condifions Data Rate 1 25 1 0625 Gb sec Fibre Channel IEEE 802 3 Compatible Rate tolerance 100ppm Fiberength b 350m sum somiam Fiber ber Length e295 m Go 5m 200k Fiber Table 7 General specifications Finisar Corporation November 16 2007 Rev A4 Page 5 FTL 8519 3D GBIC Product Specification November 2007 Finisar VII Environmental Specifications Note that the GBIC Specification requires an ambient temperature range of 0 to 50 C Finisar GBICs have an extended range from 10 C to 85 C case temperature as specified in Table 8 Symbol Min Max Units Notes Conditions Non Condensing CDRH and IEC 825 Class 1 Laser Product Table 8 Environmental Specifications VIII Serial Communication Protocol All Finisar optical GBICs implement serial identification features described for Module Definition 4 as outlined in Annex D of the GBIC Specification These GBICs use an Atmel AT24C01A 128 byte E7PROM at addr
4. Finisar Product Specification Short Wavelength GBIC Transceiver FTL 8519 3D Product Features e Upto 1 25Gb s bi directional data links e 850nm VCSEL Laser Transmitter e Optional Digital Diagnostics Functions e Extended Operating Temperature Range 10 C to 85 C Applications e Compatible with 3 3V amp 5V Systems e 1 0625Gb s Fibre Channel e Hot Pluggable complies with e 1 25 Gigabit Ethernet GBIC specification Rev 5 5 e Fully metallic enclosure for low EMI e Low power dissipation e RoHS compliant and Lead Free Finisar s FTL 8519 3D 850nm GBIC transceivers comply with GBIC Specification Revision 5 51 They are compatible with the Gigabit Ethernet as specified in IEEE Std 802 3 Fibre Channel FC PH PH2 PH3 and FC PI 2 Rev 10 04 They are RoHS compliant and lead free per Directive 2002 95 EC and Finisar Application Note AN 2038 Product Selection Part Number Digital Diagnostics FTL 8519 3D No FTL 8519 3D DD Yes Finisar Corporation November 16 2007 Rev A4 Page 1 FTL 8519 3D GBIC Product Specification November 2007 Finisar I Pin Out oxo oxo TT MOD_DERO A MOD_DEF 1 MOD_DEF 2 2 3 4 5 TADHAHE 7 oa NA ANAN TX_FAULT 10 not supported GND Table 1 GBIC to host connector pin assignment Sequence indicates the order in which pins make contact when the device is hot plugged Also see Table 3 Signal Definitions i
5. ess AOH For details on interfacing with the E PROM see the Atmel data sheet titled AT24C01A 02 04 08 16 2 Wire Serial CMOS EPROM The FTL 8519 3D also supports extended diagnostic features as described in Finisar Applications Note AN 2030 Digital Diagnostic Monitoring Interface for Optical Transceivers and additional information is available in SFF standard titled Digital Diagnostic Monitoring Interface for Optical Transceivers SFF 8472 Rev 9 3 A controller IC that monitors system parameters such as laser current module temperature transmitter power and received power is accessible at address A2H I2C clock speed digital diagnostic accuracy and digital diagnostic range can be found in the table below Values in the table represent the worst case values over temperature voltage and life Finisar Corporation November 16 2007 Rev A4 Page 6 FTL 8519 3D GBIC Product Specification November 2007 Finisar Parameter Symbol Min Typ Max Units Notes Conditions TC Clock Speed 0 100 000 Hz Bus can be driven blind Accuracy Internal Transceiver DD Temperature 3 3 C Measured at controller IC Temperature Internal Transceiver DD otiage 3 3 Measured at controller IC Supply Voltage Tx Bias Current DDgias 10 10 Tx Output Power DD py Power 3 3 dB 100 tested in production tested at room temp to 2 dB Received Average DDaxpower 3 3 dB 10
6. ion FC PI 2 Rev 10 0 American National Standard for Information Systems Directive 2002 95 EC of the European Council Parliament and of the Council on the restriction of the use of certain hazardous substances in electrical and electronic equipment January 27 2003 Application Note AN 2038 Finisar Implementation of ROHS Compliant Transceivers Finisar Corporation March 2005 AT24C01A 02 04 08 16 2 Wire Serial CMOS E7PROM Atmel Corporation www Atmel com Application Note AN 2030 Digital Diagnostic Monitoring Interface for Optical Transceivers Finisar Corporation April 2002 Digital Diagnostics Monitoring Interface for Optical Transceivers SFF Document Number SFF 8472 Revision 9 3 For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale CA 94089 1134 Tel 1 408 548 1000 Fax 1 408 541 6138 sales finisar com www finisar com Finisar Corporation November 16 2007 Rev A4 Page 9
7. n the GBIC Specification Revision 5 5 Finisar Corporation November 16 2007 Rev A4 Page 2 FTL 8519 3D GBIC Product Specification November 2007 Finisar II Electrical Power Interface Finisar FTL 8519 3D GBICs have an extended power supply voltage range of 3 15 V to 5 5 V as described in Table 2 They are compatible with both 3 3V and 5 V systems 5 3 3 Volt Electrical Power Interface ee NA NAN BANA NUN E NTEN mA Absolute Supply Voltage V max 0 3 Not to be applied continuously Open Sopp Volaee v IS asa SS VT Table 2 Electrical power interface III Low Speed Signals RX_LOS and TX_DISABLE are TTL signals as described in Table 3 MOD_DEF 1 SCL and MOD_DEF 2 SDA are open drain CMOS signals see section VI Serial Communication Protocol Both MOD_DEF 1 and MOD_DEF 2 must be pulled up to host_Vcc If host_Vcc is 3 3V then they must be pulled to 3 3V If host_Vcc is 3 3V do not pull the MOD_DEF pins to 5V For more detailed information see sections 5 3 1 5 3 8 in the GBIC Specification Rev 55 Low Speed Signals Electronic Characteristics Symbol Min Max Units Notes Conditions GBIC Output LOW VoL 0 5 V 4 7k to 10k pull up to host_Vcc measured at host side of connector measured at hoi side of Connecior GBIC Jah aaa LOW 4 7k to 10k pull up to Vcc measured at GBIC side of connector GBIC Input HIGH Vec 0 3 4 7k to 10k pull up to Vcc measured at GBIC side of connector
Download Pdf Manuals
Related Search