Home

Intel DH61CR

Contents

1. O NI Qni w Front Panel USB 2 0 Headers Figure 19 H shows the location of the front panel USB 2 0 headers and Table 12 shows the pin assignments and signal names Table 12 Front Panel USB 2 0 Headers Signal Names Pin Signal Name i Signal Name Power 5 V Power 5 V No Connection NOTE NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements even if no device or a low speed USB device is attached to the cable Use a shielded cable that meets the requirements for a full speed USB device Internal Mono Speaker Header The internal mono speaker header is shown in Figure 19 I Table 13 shows the pin assignments and signal names for the internal mono speaker header Table 13 Internal Mono Speaker Header Signal Names 49 Intel Desktop Board DH61CR Product Guide Connecting to the Audio System After installing the Realtek audio driver from the Intel Express Installer DVD ROM the multi channel audio feature can be enabled Figure 20 shows the back panel audio connectors The default connector assignments are shown in the table OM22957 Item Description A Line in B Line out front speaker headphones C Mic in Figure 20 Back Panel Audio Connectors nore NOTE The back panel line out connector is designed to power either headphones or amplified speakers only Poor audio quality may occur if passive non amp
2. PCI Express x16 Graphics Intel Core i7 Intel Core i5 Intel Core i3 and Intel Pentium processors in an LGA1155 package support discrete add in graphics cards via the PCI Express 2 0 x16 add in card connector The board supports the following PCI Express speeds e PCI Express 2 frequency of 2 5 GHz which results in 5 0 Gb s in each direction 500 MB s per lane The maximum theoretical bandwidth on the interface is 8 GB s in each direction simultaneously when operating in x16 mode e PCI Express 1 frequency of 1 25 GHz resulting in 2 5 Gb s each direction 250 MB s per lane The maximum theoretical bandwidth on the interface is 4 GB s in each direction simultaneously when operating in x16 mode 16 Desktop Board Features Audio Subsystem The board supports Intel High Definition Audio through a Realtek ALC892 audio codec The Realtek ALC892 based audio subsystem provides the following features e 6 channel audio with independent multi streaming stereo e Advanced jack sense for the back panel audio connectors that enables the audio codec to recognize the device that is connected to an audio port The back panel audio connectors are capable of retasking according to the user s definition or can be automatically switched depending on the recognized device type e Stereo input and output via back panel connectors e Headphone and Mic in functions for front panel audio connectors e A signal to noise S N ratio of 90 dB The boar
3. Always turn off the power to the computer before moving the jumper Moving the jumper with the power on may result in unreliable computer operation Figure 23 shows the location of the Desktop Board s BIOS configuration jumper block OM22969 Figure 23 Location of the BIOS Configuration Jumper Block 53 Intel Desktop Board DH61CR Product Guide The three pin BIOS jumper block enables board configuration to be done in the BIOS Setup program Table 14 shows the jumper settings for the BIOS Setup program modes Table 14 Jumper Settings for the BIOS Setup Program Modes Jumper Setting Mode J O Description Normal default 1 2 The BIOS uses the current configuration and passwords for booting 32 1 Configure 2 3 After the Power On Self Test POST runs the BIOS displays the Maintenance Menu Use this menu to clear passwords 32 1 Recovery None The BIOS recovers data in the event of a failed BIOS update CE E I 3 2 1 Clearing Passwords in the BIOS Setup Program 54 This procedure assumes that the board is installed in the computer and the configuration jumper block is set to normal mode 1 Observe the precautions in Before You Begin on page 29 2 Turn off all peripheral devices connected to the computer Turn off the computer Disconnect the computer s power cord from the AC power source wall outlet or power adapter 3 Remove the computer cover 4 Find the configuration jumper block see
4. Chassis Intrusion Intruder Ground USB 2 0 Front Panel Je TPM Header No Connection TPM_CLKRUN TPM_SERIRQ No Connection Ground LAD1 LAD2 No Connection g6 Front Panel Key no pin Front Panel Power LED SV DC On Off Reset 3J No Connection LADO 33V LAD3 PLTRST LFRAME CK_33M_TPM_DIP Power 1 LED HD LED m Key no pin Ground Rz OM22966 Figure 19 Internal Headers 45 Intel Desktop Board DH61CR Product Guide Front Panel Audio Header The front panel audio header shown in Figure 19 A supports both Intel High Definition Audio and AC 97 Audio Table 4 shows the pin assignments and signal names for HD Audio and Table 5 shows the pin assignments and signal names for AC 97 Audio Table 4 Front Panel Audio Signal Names for Intel HD Audio Pin Signal Name PORT 1L Microphone PORT 1R Microphone PORT 2R Headphone SENSE SEND PORT 2L Headphone O NI Ul DI e Signal Name Ground PRESENCE SENSE1 RETURN KEY no pin SENSE2 RETURN Table 5 Front Panel Audio Header Signal Names for AC 97 Audio Pin Signal Name MIC BIAS FP OUT R No connection FP OUT L WO N oy OR S PDIF Header Signal Name AUD_GND PRESENCE AUD_GND KEY no pin AUD_GND Figure 19 B shows the location of the S PDIF output header Table 6 shows the pin assignments an
5. European Union Declaration of Conformity Statement cesses eene Product Ecology Statements sees dE ee ANNE YA e Kr DIRE wh va a I Ra E UN a RP Ag RecyclingConsiderations messes eene China teni EMG Regulations cre rex e oe en deed er d e Fel c D C QR OR kk FCC Declaration of Conformity eet e ee eee eee nen menn enne nnne nnns Canadian Department of Communications Compliance Statement Japan VECI Statement e Balak sal ee eerie ERR NPR ndr ed FREE DC ve an Korea Class B Statement NENNEN Ensure Electromagnetic Compatibility EMC Compliance vi Contents Product Certification Ski e IRURE ROI E esa eae 78 Board Level Certifications ENEE 78 Chassis and Component Level Certifications ee e e e e e e e e e ee e eee Kee 79 ENERGY STAR e Standby and ErP Compliance 79 Figures 1 Intel Desktop Board DH61CR Components sss es eee ects ee e e ee ee e eee 12 2 TAN Status LEDS rei ala gale tural tices ee raki 18 3 Location of the Intel MEBX Reset Header 22 4 Location of the Standby Power Indicator r r 26 5 Installing the I O Shield seir noe eet er e NEEN NENNEN NNN EEN e 31 6 Intel Desktop Board DH61CR Mounting Screw Hole Locations 32 7 UnlatchtheSocketlever Gaal 33 8 Litt the
6. prompt appears press the Enter key The system will boot from the hard drive if no key is pressed within 15 seconds 5 At the Welcome to the Intel Desktop Board BIOS Upgrade CD ROM page press any key to confirm the BIOS upgrade operation 6 Wait for the BIOS upgrade process to complete Updating the BIOS A CAUTION DO NOT POWER DOWN YOUR COMPUTER before the update is complete The update may take up to 5 minutes Recovering the BIOS NorE It is unlikely that anything will interrupt the BIOS update however if an interruption occurs the BIOS could be damaged Due to BIOS size and recovery requirements a CD R with the BIO file in the root directory will be required You can obtain the Recovery BIOS Update file through your computer supplier or by navigating to the Intel Desktop Board DH61CR page on the Intel World Wide Web site Download Center at http downloadcenter intel com On the DH61CR page click on the BIOS Update link and then select the Recovery BIOS Update file NOTE For more information about updating the Intel Desktop Board BIOS or recovering from a BIOS update failure go to http support intel com support motherboards desktop sb CS 022312 htm 65 Intel Desktop Board DH61CR Product Guide 66 A Error Messages and Indicators Intel Desktop Board DH61CR reports POST errors in two ways e By sounding a beep code and blinking the front panel power LED e By displaying an error message
7. 2006 95 EC amp 2002 95 EC Italiano Questo prodotto conforme alla Direttiva Europea 2004 108 EC 2006 95 EC amp 2002 95 EC Latvie u Sis produkts atbilst Eiropas Direktivu 2004 108 EC 2006 95 EC un 2002 95 EC noteikumiem Lietuviy Sis produktas atitinka Europos direktyvu 2004 108 EC 2006 95 EC ir 2002 95 EC nuostatas Malti Dan il prodott hu konformi mal provvedimenti tad Direttivi Ewropej 2004 108 EC 2006 95 EC u 2002 95 EC Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 2004 108 EC 2006 95 EC amp 2002 95 EC Regulatory Compliance Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 2004 108 EC 206 95 EC i 2002 95 EC Portuguese Este produto cumpre com as normas da Diretiva Europ ia 2004 108 EC 2006 95 EC amp 2002 95 EC Espa ol Este producto cumple con las normas del Directivo Europeo 2004 108 EC 2006 95 EC amp 2002 95 EC Slovensky Tento produkt je v s lade s ustanoveniami eur pskych direkt v 2004 108 EC 2006 95 EC a 2002 95 EC Sloven ina Izdelek je skladen z dolo bami evropskih direktiv 2004 108 EC 2006 95 EC in 2002 95 EC Svenska Denna produkt har tillverkats i enlighet med EG direktiv 2004 108 EC 2006 95 EC amp 2002 95 EC T rk e Bu r n Avrupa Birli i nin 2004 108 EC 2006 95 EC ve 2002 95 EC y nergelerine uyar Product Ecology Statements The following information is provided to address worldwide product ecology con
8. JMA UPOZORNENI V p pad v m ny baterie za nespr vn druh m ze doj t k v buchu Je li to mo n baterie by m ly b t recyklov ny Baterie je t eba zlikvidovat v souladu s m stn mi p edpisy o ivotnim prost ed ETTEVAATUST Kui patarei asendatakse uue ebasobivat t pi patareiga v ib tekkida plahvatusoht T hjad patareid tuleb v imaluse korral viia vastavasse kogumispunkti T hjade patareide raviskamisel tuleb j rgida kohalikke keskkonnakaitse alaseid reegleid FIGYELMEZTET S Ha az elemet nem a megfelel tipusura cser li felrobbanhat Az elemeket lehet s g szerint jra kell hasznos tani A haszn lt elemeket a helyi k rnyezetv delmi el r soknak megfelel en kell kiselejtezni Installing and Replacing Desktop Board Components A UZMANIBU Pastav eksplozijas risks ja baterijas tiek nomainitas ar nepareiza veida baterijam Ja iesp jams baterijas vajadz tu nodot attiec gos pie em anas punktos Bateriju izmesanai atkritumos j notiek saska ar viet jiem vides aizsardz bas noteikumiem A DEMESIO Naudojant netinkamo tipo baterijas irenginys gali sprogti Kai tik jmanoma baterijas reikia naudoti pakartotinai Panaudotas baterijas i mesti b tina pagal vietinius aplinkos apsaugos nuostatus A ATTENZJONI Riskju ta splu joni jekk il batterija tinbidel b tip ta batterija mhux korrett batteriji g andhom ji u ri iklati fejn hu possibbli Ir rimi ta batteriji u ati g an
9. Load Plates midi ek yani aa eed x ce EA A A Plas ARAN KL 34 9 Remove the Processor from the ProtectiveCover GG 35 10 InstalltheProcessor na 35 11 SecuretheloadPlateinPlace Gara 36 12 Connecting the Processor Fan Heat Sink Power Cable to the Processor Fan Header NNN sanaana 37 13 Dual Channel Memory ConfigurationExample C G 38 14 Use DDR3 DIMMS gees aas bot ue Sege eva ruat x Eos mler i y wai PO Fea M CREARE stats 39 15 Installing a DIMM EEN 40 16 Installing a PCI Expressx16GraphicsCard 0000 42 17 Removing a PCI Express x16 Graphics Card 43 18 Connecting a Serial ATA Cable em sa parah ayau eene 44 19 Internal Headers rrr ee dor Re ER OC RR ERR E RO RR a oe PER e d 45 20 Back Panel Audio Connectors sss ee e x e e eee 50 21 Location of the Chassis Fan Headers reece eee eee nennen emen nnn 51 22 Connecting Power Supply Cables NN 52 23 LocationoftheBIOSCorfigurationlumperBlock 53 24 Removing e Ee TEE 60 25 Intel Desktop Board DH61CR China RoHS Material Self Declaration Table 74 vii Intel Desktop Board DH61CR Product Guide Tables L Feature SUN EE 9 2 Intel Desktop Board DH61CR Componenits 4 0 000 13 3 L Status LEDS States ison cede gees ad tite egerit STEE EEN tent dei een Sa Aa wasa 18 4 Front Panel Au
10. Requirements 30 Read and follow the instructions in this section and the instructions supplied with the chassis and associated modules If you do not follow these instructions and the instructions provided by the chassis and module suppliers you increase your safety risk and the possibility of noncompliance with regional laws and regulations If the instructions for the chassis are inconsistent with these instructions or the instructions for associated modules contact the suppliers to find out how you can ensure that your computer meets safety and regulatory requirements For information about the Desktop Board s regulatory compliance refer to Appendix B Installing and Replacing Desktop Board Components Installing the I O Shield The Desktop Board comes with an I O shield When installed in the chassis the shield blocks radio frequency transmissions protects internal components from dust and foreign objects and promotes correct airflow within the chassis Install the I O shield before installing the Desktop Board in the chassis Place the shield inside the chassis as shown in Figure 5 Press the shield into place so that it fits tightly and securely If the shield does not fit obtain a properly sized shield from the chassis supplier OM22959 Figure 5 Installing the I O Shield 31 Intel Desktop Board DH61CR Product Guide Installing and Removing the Desktop Board A CAUTION Only qualified technical personnel shoul
11. card connector PCI Express 2 0 x1 add in card connector Chassis intrusion header S PDIF header PCI Express 2 0 x1 add in card connector Battery PCI Express 2 0 x16 add in card connector Back panel connectors Standby power indicator LED 12 V processor core voltage connector 2 x 2 pin Rear chassis fan header Speaker Processor socket Processor fan header Front chassis fan header DDR3 DIMM 1 socket DDR3 DIMM 2 socket Trusted Platform Module TPM header Main power connector 2 x 12 pin SATA connectors BIOS configuration jumper block Front panel header Alternate front panel power LED header Intel Management Engine BIOS Extension Intel MEBX reset header Serial port header Front panel USB 2 0 headers Internal mono speaker header Front panel audio header 13 Intel Desktop Board DH61CR Product Guide Online Support For more information on Intel Desktop Board DH61CR consult the following online resources e Intel Desktop Board DH61CR http www intel com products motherboard index ht m e Desktop Board Support http www intel com p en_US support iid hdr supp ort e Available configurations for Intel http ark intel com Desktop Board DH61CR e Supported processors http processormatch intel com e Chipset information http www intel com products desktop chipsets inde x htm e BIOS and driver updates http downloadcenter intel com e Integration information http www intel com support go buil
12. encryption and signature keys at their most vulnerable stages operations when the keys are being used unencrypted in plain text form TPMs shield unencrypted keys and platform authentication information from software based attacks Fan Speed Control and Hardware Monitoring The features of the hardware monitoring and fan speed control include e Thermal sensors in the processor and the Intel PCH as well as near the processor voltage regulators and system memory e Monitoring of system voltages to detect levels above or below acceptable values e Thermally monitored closed loop fan control for all three fans that can adjust fan speed as needed e Support for chassis security feature that detects if the chassis cover has been removed The security feature uses a mechanical switch on the chassis that can be connected to the chassis intrusion header on the Desktop Board Power Management Power management is implemented at several levels including software support through the Advanced Configuration and Power Interface ACPI and the following hardware support e Power connectors e Fan headers e LAN wake capabilities e Instantly Available PC technology Suspend to RAM e 5 V standby power indicator LED e Wake from USB e PCI Power Management Event signal PME wakeup support e PCI Express WAKE signal support e Wake from serial devices e Wake from PS 2 devices 23 Intel Desktop Board DH61CR Product Guide Software Support
13. entsprechenden vom Hersteller empfohlenen Batterietyp ersetzt werden Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend AVVERTIMENTO Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore Per disfarsi delle pile usate seguire le istruzioni del produttore PRECAUCI N Existe peligro de explosi n si la pila no se cambia de forma adecuada Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo Para deshacerse de las pilas usadas siga igualmente las instrucciones del fabricante WAARSCHUWING Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij Batterijen moeten zoveel mogelijk worden gerecycled Houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving ATEN O Haver risco de explos o se a bateria for substitu da por um tipo de bateria incorreto As baterias devem ser recicladas nos locais apropriados A elimina o de baterias usadas deve ser feita de acordo com as regulamenta es ambientais da regi o A CIARO ZNA IcHye pbi3bika Bbl6yxy Kani 33aMeHeHbl AKYMY IATAp HeripaBi flbHara TbINY AkymynaTapb rlaBiHHbI Na MarubiMacui neperipauoyBauua Mazbaynayya ag crapbix akyMynsrapay narp36Ha 3rogHa 3 MAC OBbIM 3akaHaZgaycTBaM na Kanorii A A Install
14. on the monitor BIOS Error Codes Whenever a recoverable error occurs during POST the BIOS causes the board s speaker to beep and the front panel power LED to blink an error message indicating the problem see Table 15 Table 15 BIOS Beep Codes F2 Setup F10 Boot One 0 5 second beep when the BIOS is 932 Hz Menu Prompt ready to accept keyboard input BIOS update in progress Video error no add On off 1 0 second each two times then a 932 Hz in graphics card 2 5 second pause off the entire pattern For processors requiring installed repeats beeps and pause once and the an add in graphics card BIOS will continue to boot Memory error On off 1 0 second each three times then 932 Hz a 2 5 second pause off the entire pattern repeats beeps and pause until the system is powered off Thermal trip warning Alternate high and low beeps 1 0 second High beep 2000 Hz each for eight beeps followed by system Low beep 1500 Hz shut down 67 Intel Desktop Board DH61CR Product Guide Table 16 Front panel Power LED Blink Codes Type F2 Setup F10 Boot Menu Prompt BIOS update in progress Video error no add in graphics card installed Memory error Thermal trip warning yy Off when the update begins then on for 0 5 seconds then off for 0 5 seconds The pattern repeats until the BIOS update is complete On off 1 0 second each two times then a 2 5 second pause off the entire pattern rep
15. thumb drive does not need to be bootable only formatted FAT16 FAT32 and NTFS formats are supported Plug the thumb drive into a USB port of the target computer Shut down the target computer Enable the F7 prompt display a Power the computer on b Enter the BIOS Setup by pressing F2 during boot c Go to the Advanced gt Boot Configuration menu d Enable Display F7 to Update BIOS e Press F10 to save and exit During boot when the F7 prompt is displayed press F7 to enter the BIOS Flash Update tool Select the USB thumb drive and press Enter Select the BIO file and press Enter Confirm you want to update the BIOS by pressing Enter 10 Wait 2 5 minutes for the update to complete 11 Remove the thumb drive 12 Restart the computer Updating the BIOS Updating the BIOS with the ISO Image BIOS Update File or the Intel Flash Memory Update Utility You can use the information in this section to update the BIOS using either the Intel Flash Memory Update Utility or the ISO Image BIOS update file Obtaining the BIOS Update File You can update to a new version of the BIOS by using the ISO Image BIOS update file recommended or Intel Flash Memory BIOS update file The ISO Image BIOS update file is a standardized image of a bootable CD ROM that can be used to create a bootable CD that will update the BIOS The Intel Flash Memory BIOS update file is a compressed file that contains the files you need to update the BI
16. update file and copy the BIO file IFLASH EXE and ITK file optional to a bootable USB flash drive or other bootable USB media 2 Configure the BIOS or use the F10 option during POST to boot to the USB device 3 Manually run the IFLASH EXE file from the USB device and manually update the BIOS Updating the BIOS with the ISO Image BIOS Update File 64 The ISO Image BIOS update allows for the update of an Intel Desktop Board BIOS to the latest production release regardless of the operating system installed on the computer s hard drive and without the need to remove the BIOS configuration jumper It requires a blank CD R a read writeable CD drive and software capable of uncompressing and writing the ISO image file to CD The image uses ISOLINUX bootloader and automatically launches a script to upgrade the BIOS via the Intel Flash Memory Utility CAUTION Do not interrupt the process or the system may not function properly Follow these instructions to upgrade the BIOS using the ISO Image BIOS file 1 Download the ISO Image BIOS file 2 Using software capable of uncompressing and writing an ISO image file to CD burn the data to a blank CD NOTE Copying the ISO Image BIOS file to CD will not work The completed CD should contain multiple files and a directory 3 Insert the CD that was created in the CD ROM drive of the computer to be upgraded and boot the system 4 When the Press ENTER to continue booting from CD ROM
17. ACPI ACPI gives the operating system direct control over the power management and Plug and Play functions of a computer The use of ACPI with the Desktop Board requires an operating system that provides full ACPI support Hardware Support Power Connectors ATX12V compliant power supplies can turn off the computer power through system control When an ACPI enabled computer receives the correct command the power supply removes all non standby voltages When resuming from an AC power failure the computer returns to the power state it was in before power was interrupted either on or off The computer s response can be set by using the Last Power State feature in the BIOS Setup program s Boot menu The Desktop Board has two power connectors See Figure 22 on page 52 for the location of the power connectors Fan Headers The function operation of the fans is as follows e The fans are on when the board is in the ACPI SO state e The fans are off when the computer is in the ACPI S3 S4 or S5 state e Each fan header is wired to a tachometer input e All fan headers support closed loop fan control that can adjust the fan speed or switch the fan on or off as needed e All fan headers have a 12 V DC connection e All fan headers are controlled by Pulse Width Modulation e The front and rear chassis fan headers support Linear Fan Control on 3 wire fans The Desktop Board has a 4 pin processor fan header and two 4 pin chassis fan head
18. B 2 0 ports Four USB 2 0 ports are implemented with stacked back panel connectors Six USB 2 0 front panel ports are implemented through three dual port internal headers Four SATA 3 Gb s ports through the Intel H61 Express Chipset One serial port header One parallel port back panel connector One PS 2 back panel connector for mouse keyboard support Intel 82579V Gigabit 10 100 1000 Mb s Ethernet LAN controller Nuvoton W83677HG i I O controller for hardware management and serial port parallel port and PS 2 support Intel BIOS resident in an SPI Flash device Support for Advanced Configuration and Power Interface ACPI Plug and Play and SMBIOS Support for PCI Local Bus Specification Revision 2 2 Support for PCI Express Base Specification Revision 2 0 Suspend to RAM support Wake on Conventional PCI PCI Express LAN front panel serial USB ports and PS 2 Hardware monitoring through the Nuvoton I O controller Voltage sense to detect out of range power supply voltages Thermal sense to detect out of range thermal values Three fan headers using PWM control 4 pin headers for processor front chassis and rear chassis fans 4 wire and 3 wire linear fan speed control support for front and rear chassis fans Support for Platform Environmental Control Interface PECI Desktop Board Features Supported Operating Systems The Desktop Board supports the following operating systems e Microsoft Windows 7 Ulti
19. Directives 2004 108 EC EMC Directive 2006 95 EC Low Voltage Directive and 2002 95 EC ROHS Directive The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions L This product follows the provisions of the European Directives 2004 108 EC 2006 95 EC and 2002 95 EC CeStina Tento vyrobek odpov d pozadavk m evropskych sm rnic 2004 108 EC 2006 95 EC a 2002 95 EC Dansk Dette produkt er i overensstemmelse med det europaeiske direktiv 2004 108 EC 2006 95 EC amp 2002 95 EC Dutch Dit product is in navolging van de bepalingen van Europees Directief 2004 108 EC 2006 95 EC amp 2002 95 EC Eesti Antud toode vastab Euroopa direktiivides 2004 108 EC ja 2006 95 EC ja 2002 95 EC kehtestatud n uetele Suomi Tama tuote noudattaa EU direktiivin 2004 108 EC 2006 95 EC amp 2002 95 EC m r yksi Fran ais Ce produit est conforme aux exigences de la Directive Europ enne 2004 108 EC 2006 95 EC amp 2002 95 EC Deutsch Dieses Produkt entspricht den Bestimmungen der Europ ischen Richtlinie 2004 108 EC 2006 95 EC amp 2002 95 EC EAAnvika To nap v npoi v akoAou8 amp i Tic d1aTagElg Tov Euponaikov O ny wv 2004 108 EC 2006 95 EC kai 2002 95 EC Magyar E term k megfelel a 2004 108 EC 2006 95 EC s 2002 95 EC Eur pai Ir nyelv el r sainak Icelandic bessi vara stenst regluger Evr pska Efnahags Bandalagsins n mer 2004 108 EC
20. Figure 23 5 Place the jumper on pins 2 3 as shown below 6 Replace the cover plug in the computer turn on the computer and allow it to boot 7 The computer starts the Setup program Setup displays the Maintenance menu Installing and Replacing Desktop Board Components 8 Use the arrow keys to select Clear Passwords Press lt Enter gt and Setup displays a pop up screen requesting that you confirm clearing the password Select Yes and press lt Enter gt Setup displays the maintenance menu again 9 Press lt F10 gt to save the current values and exit Setup 10 Turn off the computer Disconnect the computer s power cord from the AC power source 11 Remove the computer cover 12 To restore normal operation place the jumper on pins 1 2 as shown below 13 Replace the cover plug in the computer and turn on the computer Replacing the Battery A coin cell battery CR2032 powers the real time clock and CMOS memory When the computer is not plugged into a wall socket the battery has an estimated life of three years When the computer is plugged in the standby current from the power supply extends the life of the battery The clock is accurate to 13 minutes year at 25 9C with 3 3 VSB applied When the voltage drops below a certain level the BIOS Setup program settings stored in CMOS RAM for example the date and time might not be accurate Replace the battery with an equivalent one Figure 24 on page 60 shows t
21. Intel Desktop Board DH61CR Product Guide Order Number G23547 001 Revision History Revision Revision History Date 001 First release of the Intel Desktop Board DH61CR Product Guide January 2011 Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS NO LICENSE EXPRESS OR IMPLIED BY ESTOPPEL OR OTHERWISE TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT EXCEPT AS PROVIDED IN INTEL S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS INTEL ASSUMES NO LIABILITY WHATSOEVER AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO SALE AND OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE MERCHANTABILITY OR INFRINGEMENT OF ANY PATENT COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT Intel products are not intended for use in medical life saving or life sustaining applications Intel may make changes to specifications and product descriptions at any time without notice Intel Desktop Board DH61CR may contain design defects or errors known as errata which may cause the product to deviate from published specifications Current characterized errata are available on request Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order Copies of documents which have an ordering number and are referenced in this document or other Intel literature may be obta
22. Intel Core i5 Intel Core i3 and Intel Pentium processors in an LGA1155 package Integrated graphics processing processors with Intel Graphics Technology External graphics interface controller Integrated memory controller Processor Support Chipset Intel H61 Express Chipset consisting of the Intel H61 Express Platform Controller Hub PCH Memory Support e Two 240 pin DDR3 SDRAM Dual Inline Memory Module DIMM sockets e Support for DDR3 1333 MHz and DDR3 1066 MHz DIMMs e Support for 1 Gb 2 Gb and 4 Gb memory technology e Support for up to 16 GB of system memory with two DIMMs using 4 Gb memory technology e Support for non ECC memory Graphics Support e Integrated graphics support for processors with Intel Graphics Technology VGA DVI D e Discrete graphics support for PCI Express 2 0 x16 add in graphics cards Audio Intel High Definition Audio Intel HD Audio e Realtek ALC892 audio codec e Front panel audio header Intel HD Audio and AC 97 Audio support e Mono speaker header e S PDIF audio header Expansion e One PCI Express 2 0 x16 add in card connector Capabilities e Two PCI Express 2 0 xi add in card connectors e One Conventional PCI bus connector continued Intel Desktop Board DH61CR Product Guide 10 Table 1 Feature Summary continued Peripheral Interfaces LAN Support Legacy I O BIOS Instantly Available PC Technology Hardware Monitoring Ten US
23. OS The BIOS update file contains e New BIOS file including the Intel Management Engine Intel ME Firmware Image e Intel Integrator Toolkit Configuration File optional e Intel Flash Memory Update Utility You can obtain either of these files through your computer supplier or by navigating to the Intel Desktop Board DH61CR page on the Intel World Wide Web site Download Center at http downloadcenter intel com On the DH61CR page click on the BIOS Update link and then select the the Iflash BIOS Update file Updating the BIOS with the Intel Flash Memory Update Utility NOTE With the Intel Flash Memory Update Utility you can update the system BIOS from a bootable CD ROM bootable USB flash drive or other bootable USB media The utility available on the Intel World Wide Web site provides a simple method for creating a bootable CD ROM that will automatically update your BIOS The BIOS update files can also be extracted locally to your hard drive and copied to a bootable USB flash drive or other bootable USB media The Intel Flash Memory Update Utility allows you to e Update the BIOS and Intel Management Engine in flash memory e Update the language section of the BIOS NOTE Review the instructions distributed with the update utility before attempting a BIOS update 63 Intel Desktop Board DH61CR Product Guide A CAUTION Do not interrupt the process or the system may not function properly 1 Uncompress the BIOS
24. allation CAUTION When installing a PCI Express card ensure that the card is fully seated in the PCI Express connector before you power on the system If the card is not fully seated in the connector an electrical short may result across the connector pins Depending on the over current protection of the power supply certain Desktop Board components and or traces may be damaged 41 Intel Desktop Board DH61CR Product Guide 42 Follow these instructions to install a PCI Express x16 graphics card 1 2 Observe the precautions in Before You Begin on page 29 Place the card in the PCI Express x16 connector Figure 16 A and press down on the card until it is completely seated in the connector and the card retention notch on the card snaps into place around the retention mechanism pin on the connector Secure the card s metal bracket to the chassis back panel with a screw Figure 16 B Connect a monitor to the graphics card according to the manufacturer s instructions 0M22963 Figure 16 Installing a PCI Express x16 Graphics Card Installing and Replacing Desktop Board Components Removing a PCI Express x16 Graphics Card Follow these instructions to remove a PCI Express x16 graphics card from a connector 1 2 3 Observe the precautions in Before You Begin on page 29 Disconnect the monitor cable from the graphics card back panel connector Remove the screw Figure 17 A that secures the card s me
25. ana RN lara 16 Audio SUBSYSTEM ENEE EE 17 WOES cnm 18 USB SUPPONE e kinidin asla ara ak EE AE ee 18 SATA S PDO MG aa En 19 SATA RAID u serbes a ere es yn ii ei ya a yl a V Yi YS 19 Intel Rapid RecoverTechnology Intel9RRT 20 A Elle E le te EE 20 Legacy I O 2 aa 20 BIOS EEN 20 SATA Auto Configuration NEE REENEN EEN nana n x ERR KE HR KORR ath NIE n RR NENNEN SE KEE 21 PCI PCI Express Auto Configuration sense eeeeeeeeeae neat eaen nnns 21 BIOS Security Dasewordes cece EEE amena nnns 21 Intel Manageability Technology 22 Intel MEBX Reset Header ciini doro eech 22 Trusted Platform Module TPM Support 23 Fan Speed ControlandHardwareMonitoring 23 Power Management Saksi demis ege NN ili tinal EN ERE ERE KE RP RE FERE al ORO EK KRA 23 Software Support ss e e e e e e e e e ee eee eee 24 Hardware Sup eis see Mi aaa REESEN RR EDO OR CUR SEENEN A way a yeaa 24 Onboard Speaker ext det sa kafa ux RR UR YA OUR RUD OR ORG E ER Gen ER N aii ene E 27 Real Time Clock Gubesvstem nnnm 27 2 Installing and Replacing Desktop Board Components Before YOU BEGIN sar u yaa ila de Nec APR dens ks a Reeder tind ay ae RD GE AERA kwa n 29 Installation bPrecauttons ene eese senes messes see e essen nnne 30 Prevent Power Supply Overload ee eee eee 30 Observe Safety and Regulatory Reoui
26. ard BIOS Security Passwords The BIOS includes security features that restrict whether the BIOS Setup program can be accessed and who can boot the computer A supervisor password and a user password can be set for the BIOS Setup and for booting the computer with the following restrictions e The supervisor password gives unrestricted access to view and change all Setup options If only the supervisor password is set pressing lt Enter gt at the password prompt of Setup gives the user restricted access to Setup e If both the supervisor and user passwords are set you must enter either the supervisor password or the user password to access Setup Setup options are then available for viewing and changing depending on whether the supervisor or user password was entered e Setting a user password restricts who can boot the computer The password prompt is displayed before the computer is booted If only the supervisor password is set the computer boots without asking for a password If both passwords are set you can enter either password to boot the computer For instructions on resetting the password go to Clearing Passwords on page 54 21 Intel Desktop Board DH61CR Product Guide Intel Manageability Technology Intel offers IT organizations tamper resistant and persistent management capabilities With Intel manageability IT organizations can easily get accurate platform information and can perform remote updating diagnostics debu
27. armful interference to 75 Intel Desktop Board DH61CR Product Guide radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user s authority to operate the equipment Tested to comply with FCC standards for home or office use Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil numerique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe B prescrites dans le R glement sur le broullage radio lectrique dict par le minist re des Communications du Canada Japan VCCI Statement 76 Japan Statement translation This is a Class B product based on the standard of the Voluntary Control Council for Interference from Informatio
28. cerns and regulations Recycling Considerations As part of its commitment to environmental responsibility Intel has implemented the Intel Product Recycling Program to allow retail consumers of Intel s branded products to return used products to selected locations for proper recycling Please consult http intel com intel other ehs product ecolo for the details of this program including the scope of covered products available locations shipping instructions terms and conditions etc hx VEX SOMA SESE ZR B FRERE Intel Product Recycling Program GEFRAGT ih FUCA a DA PCE SARE Dr AA d ROSE BH H Ar A T HU e AAR 26 TR x8 A ES ATI CE IH ML HD we http intel com intel other ehs product ecology T ADK RUE GRWR ZI Ekli eRe EL AKAIKE I 71 Intel Desktop Board DH61CR Product Guide 72 Deutsch Als Teil von Intels Engagement fiir den Umweltschutz hat das Unternehmen das Intel Produkt Recyclingprogramm implementiert das Einzelhandelskunden von Intel Markenprodukten erm glicht gebrauchte Produkte an ausgew hlte Standorte f r ordnungsgem Bes Recycling zur ckzugeben Details zu diesem Programm einschlieBlich der darin eingeschlossenen Produkte verf gbaren Standorte Versandanweisungen Bedingungen usw finden Sie auf der http intel com intel other ehs product ecolo Espanol Como parte de su compromiso de res
29. cover the BIOS if an update fails Updating the BIOS with the Intel Express BIOS Update Utility With the Intel Express BIOS Update utility you can update the system BIOS while in the Windows environment The BIOS file is included in an automated update utility that combines the functionality of the Intel Flash Memory Update Utility and the ease of use of Windows based installation wizards To update the BIOS with the Intel Express BIOS Update utility 1 Go to the Intel World Wide Web site Download Center at http downloadcenter intel com 2 Navigate to the DH61CR page Click on the BIOS Update link and then select the Express BIOS Update file 3 Download the file to your hard drive You can also save this file to a removable USB device This is useful if you are updating the BIOS for multiple identical systems 4 Close all other applications This step is required Your system will be rebooted at the last Express BIOS Update window 5 Double click the executable file from the location on your hard drive where it was saved This runs the update program 6 Follow the instructions provided in the dialog boxes to complete the BIOS update 61 Intel Desktop Board DH61CR Product Guide Updating the BIOS Using the F7 Function Key To use this BIOS update method 62 1 2 Ge 7 8 9 Download and save the Recovery BIOS BIO file to a temporary directory Copy the BIO file to a USB thumb drive The USB
30. curate Replace the battery with an equivalent one Go to page 55 for instructions on how to replace the battery 27 Intel Desktop Board DH61CR Product Guide 28 2 Installing and Replacing Desktop Board Components This chapter tells you how to e Install the I O shield e Install and remove the Desktop Board e Install and remove a processor e Install and remove memory e Install and remove a PCI Express x16 card e Connect Serial ATA cables e Connect to the internal headers e Connect to the audio system e Connect chassis fan and power supply cables e Set the BIOS configuration jumper e Clear passwords e Replace the battery Before You Begin A CAUTIONS The procedures in this chapter assume familiarity with the general terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment Disconnect the computer from its power source and from any telecommunications links networks or modems before performing any of the procedures described in this chapter Failure to disconnect power telecommunications links networks or modems before you open the computer or perform any procedures can result in personal injury or equipment damage Some circuitry on the board can continue to operate even though the front panel power button is off Follow these guidelines before you begin e Always follow the steps in each procedure in the correct
31. d perform this procedure Disconnect the computer from its power source before performing the procedures described here Failure to disconnect the power before you open the computer can result in personal injury or equipment damage Refer to your chassis manual for instructions on installing and removing the Desktop Board Figure 6 shows the location of the mounting screw holes for Intel Desktop Board DH61CR Figure 6 Intel Desktop Board DH61CR Mounting Screw Hole Locations 32 Installing and Replacing Desktop Board Components Installing and Removing a Processor Instructions on how to install the processor on the Desktop Board are given below Installing a Processor A CAUTION Before installing or removing a processor make sure the AC power has been removed by unplugging the power cord from the computer the standby power LED should not be lit see Figure 4 on page 26 Failure to do so could damage the processor and the board To install a processor follow these instructions 1 Observe the precautions in Before You Begin on page 29 2 Unlatch the processor socket lever by pushing it down and away from the socket Figure 7 A B OM22677 Figure 7 Unlatch the Socket Lever 33 Intel Desktop Board DH61CR Product Guide 3 Rotate the socket lever to lift the load plate away from the socket Figure 8 A Make sure that the load plate is in the fully open position Figure 8 B while being careful not to damag
32. d provides onboard audio headers and back panel connectors The onboard audio headers include the following e Front panel audio a 2 x 5 pin header that provides headphone and mic in signals for front panel audio connectors e S PDIF audio header 1 x 4 pin header e Internal mono speaker header 1 x 2 pin header Front panel headphone output is supported by a separate audio channel pair allowing multi streaming audio configurations such as simultaneous surround sound playback and stereo audio conferencing through speakers connected to the back panel audio connectors and a headset connected to the front panel audio connectors The onboard internal mono speaker header allows connection to an internal low power speaker for basic system sound capability The subsystem is capable of driving a speaker load of 8 O at 1 W rms or 4 Q at 1 5 W rms The onboard S PDIF header allows connection to coaxial or optical adapters for digital audio output The back panel audio connectors are configurable through the audio device drivers Audio software and drivers are available from http downloadcenter intel com 17 Intel Desktop Board DH61CR Product Guide LAN Subsystem The LAN subsystem includes e Intel 82579V Gigabit 10 100 1000 Mb s Ethernet LAN controller e RJ 45 LAN connector with integrated status LEDs LAN software and drivers are available at http downloadcenter intel com Two LEDs are built into the RJ 45 LAN con
33. d signal names for the S PDIF output header Table 6 S PDIF Header Signal Names Pin Description 1 Ground 2 S PDIF Out 3 Key no pin 4 5 VDC 46 Installing and Replacing Desktop Board Components Chassis Intrusion Header Figure 19 C shows the location of the chassis intrusion header This header can be connected to a mechanical switch on the chassis to detect if the chassis cover is removed This switch should be in the open position when the chassis cover is installed and closed when the cover is removed Table 7 shows the pin assignments and signal names for the chassis intrusion header Table 7 Chassis Intrusion Header Signal Names Pin Description 1 Intruder 2 Ground TPM Header The TPM header is shown in Figure 19 D Table 8 shows the pin assignments and signal names for TPM header Table 8 TPM Header Signal Names Pin Signal Name Pin Signal Name 1 CK_33M_TPM_DIP 2 Ground 3 LFRAME 4 Key no pin 5 PLTRST 6 No connection 7 LAD3 8 LAD2 9 3 3 V 10 LAD1 11 LAD0 12 Ground 13 No connection 14 No connection 15 3 3 VSB 16 TPM_SERRQ 17 Ground 18 TPM_CLKRUN 19 LPCPD 20 No connection 47 Intel Desktop Board DH61CR Product Guide Front Panel Header Figure 19 E shows the location of the front panel header Table 9 shows the pin assignments and signal names for the front panel header Table 9 Front Panel Header Signal Names Pin Description In Out Pin Descri
34. dio Signal Names for Intel HDAud o 46 5 Front Panel Audio Header Signal NamesforAC 97Audio 46 6 S PDIF Header Signal NAMES NENNEN 46 7 ChassisintrusionHeaderSignalNames 47 8 TPM Header Signal Names eae REM EN A ENNEN ERR EN 47 9 Front Panel Header Signal Names sese eee e e e ee eee e e eee 48 10 Alternate FrontPanelPowerLEDHeaderSignalNames 48 11 SerialPortHeaderSignalNames emnes 49 12 Front Panel USB2 0HeadersSignalNames 49 13 Internal Mono Speaker Header Signal Names 49 14 Jumper Settings for the BIOS Setup Program Modes eee eee eee teen eee 54 15 Oe BEE 67 16 Front panel PowerLEDBlinkCodes GG 68 175 BIOS Error Messages na yu yank ra a Baka di E Re DPA ire aya ii 68 18 Safety Standards eese a a alani dee lama Manen 69 19 EMC Regulations eiecti een Dan ula lke la rm la ald 75 20 RegulatoryComplianceMarks GG 78 viii 1 Desktop Board Features This chapter briefly describes the features of Intel Desktop Board DH61CR Table 1 summarizes the major features of the Desktop Board Table 1 Feature Summary Form Factor MicroATX 243 84 millimeters 9 60 inches x 198 12 millimeters 7 80 inches e Intel Core i7
35. dit Processor AN CAUTION 14 Failure to use an appropriate power supply and or not connecting the 12 V 2 x 2 pin power connector to the Desktop Board may result in damage to the board or the system may not function properly Intel Desktop Board DH61CR supports Intel Core i7 Intel Core i5 Intel Core i3 and Intel Pentium processors in the LGA1155 package Processors are not included with the Desktop Board and must be purchased separately The processor connects to the Desktop Board through an LGA1155 socket For information on supported processors for Intel Desktop Board DH61CR go to http processormatch intel com Desktop Board Features Intel H61 Express Chipset The Intel H61 Express Chipset consisting of the Intel H61 Platform Controller Hub PCH provides interfaces to the processor and the USB SATA LPC audio network display and PCI Express interfaces The PCH is a centralized controller for the board s I O paths Main Memory NOTE NOTE To be fully compliant with all applicable Intel SDRAM memory specifications the board should be populated with DIMMs that support the Serial Presence Detect SPD data structure If your memory modules do not support SPD you will see a notification to this effect on the screen at power up The BIOS will attempt to configure the memory controller for normal operation The board has two DIMM sockets and supports the following memory features Two independ
36. du jsir skond ir regolamenti ambjentali lokali A OSTRZEZENIE Ryzyko wybuchu w przypadku wymiany na baterie niewlasciwego typu W miare mozliwosci baterie nale y podda recyklingowi Zuzytych baterii nale y pozbywa sie zgodnie z lokalnie obowi zuj cymi przepisami w zakresie ochrony rodowiska 59 Intel Desktop Board DH61CR Product Guide 60 To replace the battery follow these steps 1 2 Observe the precautions in Before You Begin see page 29 Turn off all peripheral devices connected to the computer Disconnect the computer s power cord from the AC power source wall outlet or power adapter Remove the computer cover Locate the battery on the board see Figure 24 With a medium flat bladed screwdriver gently pry the battery free from its connector Note the orientation of the and on the battery Install the new battery in the connector orienting the and correctly Replace the computer cover 0M22972 Figure 24 Removing the Battery 3 Updating the BIOS The BIOS Setup program can be used to view and change the BIOS settings for the computer You can access the BIOS Setup program by pressing the lt F2 gt key after the Power On Self Test POST memory test begins and before the operating system boot begins This chapter tells you how to update the BIOS by either using the Intel Express BIOS Update utility or the Intel Flash Memory Update Utility and how to re
37. e adjacent components Do not touch the socket contacts OM22678 Figure 8 Lift the Load Plate 34 Installing and Replacing Desktop Board Components 4 Remove the processor from its protective cover Hold the processor only at the edges being careful not to touch the bottom of the processor see Figure 9 NOTE Do not discard the processor cover Always replace the processor cover if you remove the processor from the socket OM22679 Figure 9 Remove the Processor from the Protective Cover 5 Hold the processor with your thumb and index finger oriented as shown in Figure 10 to align your fingers with the socket finger cutouts Make sure that the processor Pin 1 indicator gold triangle is aligned with the Pin 1 chamfer on the socket Figure 10 B and that the notches on the processor align with the posts on the socket Figure 10 C Lower the processor straight down without tilting or sliding it in the socket Figure 10 A OM22680 Figure 10 Install the Processor 35 Intel Desktop Board DH61CR Product Guide 6 Carefully lower the socket lever Figure 11 A while making sure that the front edge of the load plate slides under the shoulder screw cap as the lever is lowered Latch the socket lever under the load plate tab Figure 11 C D The socket cover Figure 11 B will pop off as shown OM22681 Figure 11 Secure the Load Plate in Place 7 Pick up the socket cover and remove it from the desktop b
38. eats blink and pause until the system is powered off On off 1 0 second each three times then a 2 5 second pause off the entire pattern repeats blinks and pause until the system is powered off Each beep will be accompanied by the following blink pattern 25 seconds on 25 seconds off 25 seconds on 25 seconds off This results in a total of 16 blinks BIOS Error Messages 68 Error Message CMOS Battery Low CMOS Checksum Bad Memory Size Decreased No Boot Device Available Table 17 BIOS Error Messages Explanation Note For processors requiring an add in graphics card When a recoverable error occurs during the POST the BIOS displays an error message describing the problem Table 17 gives an explanation of the BIOS error messages The battery may be losing power Replace the battery soon The CMOS checksum is incorrect CMOS memory may have been corrupted Run Setup to reset values Memory size has decreased since the last boot If no memory was removed then memory may be bad System did not find a device to boot B Regulatory Compliance This appendix contains the following regulatory compliance information for Intel Desktop Board DH61CR e Safety standards e European Union Declaration of Conformity statement e Product Ecology statements e Electromagnetic Compatibility EMC regulations e Product certifications Safety Standards Intel Desktop Board DH61CR complies with the
39. ent Interface Specification Add in cards that support this specification can participate in power management and can be used to wake the computer The use of Instantly Available PC technology requires operating system support and PCI 2 2 compliant add in cards PCI Express add in cards and drivers 5 V Standby Power Indicator LED A CAUTION If the AC power has been switched off and the standby power indicator is still lit disconnect the power cord before installing or removing any devices connected to the board Failure to do so could damage the board and any attached devices The Desktop Board s standby power indicator LED shown in Figure 4 is lit when there is standby power still present on the board even when the computer appears to be off For example when this green LED is lit standby power is still present at the memory module sockets and the PCI connector 25 Intel Desktop Board DH61CR Product Guide LEE C d n LE HB 9 s i 3333333333 0M22971 Figure 4 Location of the Standby Power Indicator For more information on standby current requirements for the Desktop Board refer to the Technical Product Specification at http www intel com support motherboards desktop Wake from USB NOTE Wake from USB requires the use of a USB peripheral that supports Wake from USB and an operating system that supports Wake from USB USB bus activity wakes the computer from an ACPI S3 state PCI PME Signal Wake
40. ent memory channels with interleaved mode support Support for non ECC unbuffered single sided or double sided DIMMs with x8 organization 16 GB maximum total system memory with 4 Gb memory technology e Minimum total system memory 1 GB using 1 Gb x8 modules e Serial Presence Detect e DDR3 1333 MHz and DDR3 1066 MHz SDRAM DIMMs NOTE 32 bit operating systems are limited to a maximum of 4 GB of memory These operating systems will report less than 4 GB because of the memory used by add in graphics cards and other system resources 15 Intel Desktop Board DH61CR Product Guide Graphics Subsystem The board supports either integrated graphics Intel Graphics Technology or PCI Express 2 0 x16 graphics Integrated Graphics The board supports integrated graphics through the Intel Flexible Display Interface Intel FDI for processors with Intel Graphics Technology Analog Display VGA The VGA port supports analog displays The maximum supported resolution is 2048 x 1536 QXGA at a 75 Hz refresh rate The VGA port is enabled for POST whenever a monitor is attached regardless of the DVI D connector status Digital Visual Interface Intel Desktop Board DH61CR supports Digital Visual Interface DVI displays with a DVI D back panel port The DVI D port supports only digital DVI displays The maximum supported resolution is 2048 x 1536 at a 75 Hz refresh rate QXGA The DVI D port is compliant with the DVI 1 0 specification
41. ers that are compatible with 4 wire and 3 wire chassis fans LAN Wake Capabilities AN 24 CAUTION For LAN wake capabilities the 5 V standby line for the power supply must be capable of delivering adequate 5 V standby current Failure to provide adequate standby current when using this feature can damage the power supply LAN wakeup capabilities enable remote wake up of the computer through a network The LAN subsystem monitors network traffic and upon detecting a Magic Packet frame it asserts a wake up signal that powers up the computer Desktop Board Features Instantly Available PC Technology A CAUTION For Instantly Available PC technology the 5 V standby line for the power supply must be capable of delivering adequate 5 V standby current Failure to provide adequate standby current when using this feature can damage the power supply and or effect ACPI S3 sleep state functionality Instantly Available PC technology enables the board to enter the ACPI S3 Suspend to RAM sleep state Instantly Available PC technology enables the board to enter the ACPI S3 Suspend to RAM sleep state While in the S3 sleep state the computer will appear to be off the power supply is off and the front panel power LED will behave as configured by the BIOS S3 State Indicator option When signaled by a wake up device or event the system quickly returns to its last known wake state The Desktop Board supports the PCI Bus Power Managem
42. gging and repair of a system regardless of the state of the operating system or the power state of the system The Intel manageability subsystem consists of e Intel Management Engine Intel ME microcontroller embedded in the Intel H61 PCH e BIOS SPI Flash e Intel MEBX reset header Intel MEBX Reset Header This header see Figure 3 allows you to reset the Intel ME configuration to factory defaults Momentarily shorting pins 1 and 2 with a jumper not supplied will accomplish the following e Return all Intel ME parameters to their default values e Delete any user entered information including PID PPS and user entered Hash Certificates USB key and remote configuration data will be removed if the parameters are not default parameters e Reset the Intel MEBX password to the default value admin 0M22970 Figure 3 Location of the Intel MEBX Reset Header 22 Desktop Board Features NOTE NOTE Software with Intel manageability capability is required to take advantage of the Intel platform management capabilities Trusted Platform Module TPM Support Intel Desktop Board DH61CR provides a header to connect to an external TPM The header is shown in Figure 1 R on page 12 and the header pinout is listed in Table 8 on page 47 TPMs are designed to enhance platform security by providing a protected space for key operations and other security critical tasks Using both hardware and software the TPM protects
43. he location of the battery CAUTION Risk of explosion if the battery is replaced with an incorrect type Batteries should be recycled where possible Disposal of used batteries must be in accordance with local environmental regulations PR CAUTION Risque d explosion si la pile usag e est remplac e par une pile de type incorrect Les piles usag es doivent tre recycl es dans la mesure du possible La mise au rebut des piles usag es doit respecter les r glementations locales en vigueur en mati re de protection de l environnement FORHOLDSREGEL Eksplosionsfare hvis batteriet erstattes med et batteri af en forkert type Batterier b r om muligt genbruges Bortskaffelse af brugte batterier bor foreg i overensstemmelse med g ldende milj lovgivning 55 Intel Desktop Board DH61CR Product Guide A A A 56 OBS Det kan oppst eksplosjonsfare hvis batteriet skiftes ut med feil type Brukte batterier b r kastes i henhold til gjeldende milj lovgivning VIKTIGT Risk f r explosion om batteriet ers tts med felaktig batterityp Batterier ska kasseras enligt de lokala milj v rdsbest mmelserna VARO R j hdysvaara jos pariston tyyppi on v r Paristot on kierr tett v jos se on mahdollista K ytetyt paristot on h vitett v paikallisten ymp rist m r ysten mukaisesti VORSICHT Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr Die Batterie darf nur durch denselben oder einen
44. icators information about BIOS error messages and beep codes B Regulatory Compliance describes the board s adherence to safety standards and EMC regulations and its product certifications Conventions The following conventions are used in this manual AN CAUTION Cautions warn the user about how to prevent damage to hardware or loss of data NOTE NOTE Notes call attention to important information Intel Desktop Board DH61CR Product Guide Terminology The table below gives descriptions of some common terms used in the product guide Term Description GB Gigabyte 1 073 741 824 bytes GHz Gigahertz one billion hertz KB Kilobyte 1024 bytes MB Megabyte 1 048 576 bytes Mb Megabit 1 048 576 bits MHz Megahertz one million hertz Contents 1 Desktop Board Features Supported Operating Systems u uu xa ex X Rh RERRR EN SEN NENNEN NEEN SE ENN NEES E e 11 Desktop Board COMPONEN tS uuu a S 4 9555999525595542 aaa HEE aaa SEE SEER ESS 12 PIOCCSSON eU 14 Intel H61 Express Chipset e 15 Mam Memory EE 15 Graphics SUubSYSteM ed t eg Eed seri eeu d AER SE Nd a zen alk d ENEE ka mean ENEE 16 Integrated Graphie eerst ova dE SNE ee rA acu Read hyde Ap renee orks EN mma kaw eae es 16 Analog Display VGA nena ne tne senes 16 Digital Visual Interface uyan ai e REX in y ERR xa ieee Gk 16 PCI Express x16 Graphics eet ENN a A a saq SE KR ened NUS ea k
45. ined from Intel Corporation by going to the World Wide Web site at http www intel com or by calling 1 800 548 4725 Intel Intel Core and Pentium are trademarks of Intel Corporation in the U S and other countries Other names and brands may be claimed as the property of others Copyright 2011 Intel Corporation All rights reserved Preface This Product Guide gives information about board layout component installation BIOS update and regulatory requirements for Intel Desktop Board DH61CR Intended Audience The Product Guide is intended for technically qualified personnel It is not intended for general audiences Use Only for Intended Applications All Intel Desktop Boards are evaluated as Information Technology Equipment I T E for use in personal computers PC for installation in homes offices schools computer rooms and similar locations The suitability of this product for other PC or embedded non PC applications or other environments such as medical industrial alarm systems test equipment etc may not be supported without further evaluation by Intel Document Organization The chapters in this Product Guide are arranged as follows 1 Desktop Board Features a summary of product features 2 Installing and Replacing Desktop Board Components instructions on how to install the Desktop Board and other hardware components 3 Updating the BIOS instructions on how to update the BIOS A Error Messages and Ind
46. ing and Replacing Desktop Board Components UPOZORNIN V p pad v m ny baterie za nespr vn druh m ze doj t k v buchu Je li to mo n baterie by m ly b t recyklov ny Baterie je t eba zlikvidovat v souladu s m stn mi p edpisy o ivotn m prost ed NMpoooxn Yridpxei K v uvo yia Ekpn n GE NEp NTMOT nou n uriaTapia avrikaraora si ano uia AavOaoyu amp vou TUnou Ol unaTtapie Ga np amp riei va AVaKUKAMVOVTGI TAV K TI T TOIO Elvai OuvaTo H anoppiwn rov xprjoiuonoi u amp vov unarapiov np ne va ylverai c ugova LE TOU KATA T NO nepiBaAAovrikoUG KAVOVIOLIOUG VIGY ZAT Ha a telepet nem a megfelel t pus telepre cser li az felrobbanhat A telepeket lehet s g szerint Ujra kell hasznositani A haszn lt telepeket a helyi k rnyezetv delmi el r soknak megfelel en kell kiselejtezni HE A OMHOBHERAT t RAED ERMDUR JHII ASA RE SIC AIL hX UW JL LC ESL POS HE RRS ORTI Kb oi ES T lt CSL AWAS Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul Bateri sepatutnya dikitar semula jika boleh Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan OSTRZEZENIE Istnieje niebezpieczenstwo wybuchu w przypadku zastosowania niew a ciwego typu baterii Zu yte baterie nale y w miar mo liwo ci utylizowa zgodnie z odpowiednimi przepisami ochrony rodowiska PRECAUTIE Risc de explozie daca bateria este nlocuit cu un tip de bate
47. ipment International CISPR 24 Information Technology Equipment Immunity Characteristics Limits and Methods of Measurement International VCCI V 3 V 4 Voluntary Control for Interference by Information Technology Equipment Japan KN 22 KN 24 Korean Communications Commission Framework Act on Telecommunications and Radio Waves Act South Korea CNS 13438 Bureau of Standards Metrology and Inspection Taiwan FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For questions related to the EMC performance of this product contact Intel Corporation 5200 N E Elam Young Parkway Hillsboro OR 97124 1 800 628 8686 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause h
48. larak perakende t keticilerin Intel markal kullan lm r nlerini belirlenmi merkezlere iade edip uygun ekilde geri d n t rmesini ama layan Intel r nleri Geri D n m Program n uygulamaya koymu tur Bu program n r n kapsam r n iade merkezleri nakliye talimatlar kay tlar ve artlar v s dahil b t n ayr nt lar n grenmek i in l tfen http intel com intel other ehs product ecology web sayfas na gidin 73 Intel Desktop Board DH61CR Product Guide China RoHS 74 Intel Desktop Board DH61CR is a China RoHS compliant product The China Ministry of Information Industry MII stipulates that a material Self Declaration Table SDT must be included in a product s user documentation The SDT for Intel Desktop Board DH61CR is shown in Figure 25 TRER er m TET HER Management Methods on Control of Pollution from Electronic Information Products China RoHS declaration el KH SRL E A8 EV MA Parts E ES i ZU EE AE Pb Hg Cd Cr6 PBB PBDE x o o O a E Motherboard Assembly o RX 5 8543 W LE IMA Hl PH ABUSE SJ T 11363 2006 EREN RERKAT Indicates that this hazardous substance contained in all homogeneous materials of this part is below the limit requirement in SJ T 11363 2006 x S 25 5545 jn bip Stinn 3 15 mms mH SJ 11363 2006 1 ZR B k x Indicates that this hazardous substance contained in at least one of the homogeneou
49. lified speakers are connected to this output 50 Installing and Replacing Desktop Board Components Connecting Chassis Fan and Power Supply Cables Connecting Chassis Fan Cables Connect chassis fan cables to the chassis fan headers on the Desktop Board Figure 21 shows the location of the chassis fan headers 0M22967 Figure 21 Location of the Chassis Fan Headers 51 Intel Desktop Board DH61CR Product Guide Connecting Power Supply Cables A CAUTION 52 Failure to use an appropriate power supply and or not connecting the 12 V power connector Figure 22 A to the Desktop Board may result in damage to the board or the system may not function properly Figure 22 shows the location of the power connectors The 2 x 12 pin main power connector Figure 22 B is backwards compatible with ATX12V power supplies with 2 x 10 connectors NOTE If your power supply has a 2 x 10 main power connector it is recommended that you do not install a PCI Express x16 graphics card unless it has a direct connection to the power supply OM22968 Figure 22 Connecting Power Supply Cables 1 Observe the precautions in Before You Begin on page 29 2 Connect the 12 V processor core voltage power supply cable to the 2 x 2 pin connector Figure 22 A 3 Connect the main power supply cable to the 2 x 12 pin connector Figure 22 B Installing and Replacing Desktop Board Components Setting the BIOS Configuration Jumper NOTE
50. mate 64 bit edition e Microsoft Windows 7 Ultimate 32 bit edition e Microsoft Windows 7 Professional 64 bit edition e Microsoft Windows 7 Professional 32 bit edition e Microsoft Windows 7 Home Premium 64 bit edition e Microsoft Windows 7 Home Premium 32 bit edition e Microsoft Windows 7 Starter 64 bit edition e Microsoft Windows 7 Starter 32 bit edition e Microsoft Windows Vista Ultimate 32 bit edition e Microsoft Windows Vista Business 32 bit edition e Microsoft Windows Vista Home Premium 32 bit edition e Microsoft Windows Vista Home Basic 32 bit edition e Microsoft Windows Vista Ultimate 64 bit edition e Microsoft Windows Vista Business 64 bit edition e Microsoft Windows Vista Home Premium 64 bit edition e Microsoft Windows Vista Home Basic 64 bit edition e Microsoft Windows XP Media Center Edition 2005 e Microsoft Windows XP Professional e Microsoft Windows XP Professional x64 Edition e Microsoft Windows XP Home 11 Intel Desktop Board DH61CR Product Guide Desktop Board Components Figure 1 shows the approximate location of the major components on Intel Desktop Board DH61CR Line In BB AA J K Z L M N Y e 0 P Q W e R OM22956 Figure 1 Intel Desktop Board DH61CR Components 12 Desktop Board Features Table 2 Intel Desktop Board DH61CR Components Label 2 N lt gt x Z lt Chan A e Uc Me EE 2 z MA T 0 um 9 O W gt D o gt Description Conventional PCI bus add in
51. ment at the front of this product guide demonstrates compliance with Canadian EMC regulations ENERGY STAR e Standby and ErP Compliance The US Department of Energy and the US Environmental Protection Agency have continually revised the ENERGY STAR requirements Intel has worked directly with these two governmental agencies in the definition of the new requirements This Desktop Board meets the ENERGY STAR Program for Computers Version 5 0 Category A requirements For information about ENERGY STAR requirements and recommended configurations go to http www intel com go energystar The Desktop Board also meets the following international requirements e Republic of Korea e Standby program e European Union Energy using Products ErP Lot 6 directive 79 Intel Desktop Board DH61CR Product Guide 80
52. mulangkan produk terguna ke lokasi lokasi terpilih untuk dikitarkan semula dengan betul Sila rujuk http intel com intel other ehs product ecology untuk mendapatkan butir butir program ini termasuklah skop produk yang dirangkumi lokasi lokasi tersedia arahan penghantaran terma amp syarat dsb Regulatory Compliance Portuguese Como parte deste compromisso com o respeito ao ambiente a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados onde esses produtos sdo reciclados de maneira adequada Consulte o site http intel com intel other ehs product ecology em Ingl s para obter os detalhes sobre este programa inclusive o escopo dos produtos cobertos os locais dispon veis as instru es de envio os termos e condi es etc Russian B kauecrBe yacTn cBOMX 0683aTe IBCTB K okpyxaroujel cpege B Intel cosnaHa nporpaMMa yrMnuaauua npogyKuun Intel Product Recycling Program ana NpeAOcTaBNeHUA KOHeuHbIM NOMb30BaTeENAM Mapok MpOAYKLUUMU Intel Bo3MOXHOCTM BO3Bpara UCNONb3YeMON npoaykLiMa B cneunuanal3upoBaHHble NYHKTbI ANA AOMKHON yrunu3auMw Noxanyucta o6parurecb Ha Be6 caltr http intel com intel other ehs product ecology 3a nHbopmaLme o6 ston nporpaMMe npuHuMaeMbIX npogykrax Mecrax npnema WHCTPYKUMAX o6 ornpaske H0JIOXeHMsx M YCNOBMAX N T A T rkce Intel evre sorumlulu una ba ml l n n bir par as o
53. n Connectirig to the Audio System smear tet et rh a RR RR RE Ra aa dere N E Sen Connecting Chassis Fan and Power Supply Cables nmm Connecting Chassis Fan Cables emnes Connecting Power Supply Cables eee ee eee ea sean nnns Setting the BIOS Configuration Jumper Clearing Passwords in the BIOS Setup Program Replacing the Battery usa su usss pre n erra eta vated es NEEN NENNEN ga ra a ENN NN 3 Updating the BIOS Updating the BIOS with the Intel Express BIOS Update Utility eens Updating the BIOS Using the F7 Function Key eee eee eee eee meme Updating the BIOS with the ISO Image BIOS Update File or the Intel Flash Memory Update Utility usi aa ak pre BD aaa Qua EMAN deinen EN Obtaining the BIOS Update File vay gaa sare YA TR ey CX eee eee eee teeta mene Updating the BIOS with the Intel Flash Memory Update Utility Updating the BIOS with the ISO Image BIOS Update File Recovering the BIOS ceria al ea aa usha a al uwa qaa kama A Error Messages and Indicators BIOS Error Codes ioc se e ached da Ee ENK A ERA E E EE ER EVA NA BIOS Error MESSAGES sage su sama li eet rd lama dagen edet lik a e qr asa sua ai cues reo neris B Regulatory Compliance Safety Standards iter ero eei et ee nex ve lee EE REN E PAN C Ra o eda teed Battery Caution sora rez emirle siz kaya papa iet e vaa Fa ausu Va SERES DA YOU Vr CDI YR ERN TA
54. n Technology Equipment VCCI If this is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual CORES HHRUBLESERRSATMHBMS VCCI OB CEDC IFB ERRET TORE SIR CER Scc HR CUCU 2 CORBPIVAPTLEYV ar FERTELT HEn2E FERRE ET Icht RIBAS Itt T IE LLM U BBL LTE EL Regulatory Compliance Korea Class B Statement Korea Class B Statement translation This equipment is for home use and has acquired electromagnetic conformity registration so it can be used not only in residential areas but also other areas e 77 7H8 amp Bu 9 AABAPSSS S 77124 FE ARAN ASS AG HA OB Fu WE AJNA ASA 4 Hau Ensure Electromagnetic Compatibility EMC Compliance Before computer integration make sure that the power supply and other modules or peripherals as applicable have passed Class B EMC testing and are marked accordingly Pay close attention to the following when reading the installation instructions for the host chassis power supply and other modules e Product certifications or lack of certifications e External I O cable shielding and filtering e Mounting grounding and bonding requirements e Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals as applicable are not Class B EMC compliant before integration then EMC testing may be required on a re
55. nector located on the back panel see Figure 2 These LEDs indicate the status of the LAN as shown in Table 3 A B OM22958 Figure 2 LAN Status LEDs Table 3 LAN Status LEDs States LED Indicates A Link Activity Green Off LAN link is not established LAN link is established LAN activity is occurring B Link Speed 10 Mb s data rate 100 Mb s data rate 1000 Mb s data rate USB Support 18 The Desktop Board supports USB 2 0 There are 10 USB 2 0 ports four ports routed to back panel connectors and six ports routed to three onboard headers The USB 2 0 ports are high speed full speed and low speed capable USB 2 0 support requires both an operating system and drivers that fully support USB 2 0 transfer rates Desktop Board Features SATA Support The board provides four SATA 3 0 Gb s channels through the PCH which support one device per channel SATA RAID 8 The Intel H61 PCH supports Intel Rapid Storage Technology Intel RST which enables the following RAID Redundant Array of Independent Drives levels e RAID O data striping e RAID 1 data mirroring e RAID 0 1 or RAID 10 data striping and mirroring e RAID 5 distributed parity NOTE In order to use supported RAID features you must first enable RAID in the BIOS Also during Microsoft Windows XP installation you must press F6 to install the RAID drivers See your Microsoft Windows XP documentation for more information ab
56. oard Note NOTE Do not discard the socket cover save it for possible future use Always replace the socket cover if you remove the processor from the socket 36 Installing and Replacing Desktop Board Components Installing a Processor Fan Heat Sink Intel Desktop Board DH61CR has mounting holes for a processor fan heat sink For instructions on how to attach the processor fan heat sink to the Desktop Board refer to the boxed processor manual or boxed thermal solution manual Connecting the Processor Fan Heat Sink Cable Connect the processor fan heat sink power cable to the 4 pin processor fan header see Figure 12 A fan with a 4 pin connector as shown in Figure 12 is recommended U S 0M22973 Figure 12 Connecting the Processor Fan Heat Sink Power Cable to the Processor Fan Header Removing the Processor For instructions on how to remove the processor fan heat sink and processor refer to the processor installation manual 37 Intel Desktop Board DH61CR Product Guide Installing and Removing System Memory NOTE To be fully compliant with all applicable Intel SDRAM memory specifications the board requires DIMMs that support the Serial Presence Detect SPD data structure The desktop board has two 240 pin DDR3 DIMM sockets providing Channel A and Channel B For dual channel performance install a matched pair of DIMMs equal in speed and size
57. onmental Friendly Usage Period EFUP for Intel Desktop Boards has been determined to be 10 years mb 78 Regulatory Compliance Chassis and Component Level Certifications Ensure that the chassis and certain components such as the power supply peripheral drives wiring and cables are components certified for the country or market where used Agency certification marks on the product are proof of certification Typical product certifications include In Europe The CE mark indicates compliance with all applicable European requirements If the chassis and other components are not properly CE marked a supplier s Declaration of Conformity statement to the European EMC directive Low Voltage directive as applicable and ROHS directive should be obtained Additionally other directives such as the Radio and Telecommunications Terminal Equipment R amp TTE directive may also apply depending on product features In the United States A certification mark by a Nationally Recognized Testing Laboratory NRTL such as UL CSA or ETL signifies compliance with safety requirements Wiring and cables must also be UL listed or recognized and suitable for the intended use The FCC Class B logo for home or office use signifies compliance with electromagnetic interference EMI requirements In Canada A nationally recognized certification mark such as CSA or cUL signifies compliance with safety requirements The Industry Canada state
58. order e Set up a log to record information about your computer such as model serial numbers installed options and configuration information e Electrostatic discharge ESD can damage components Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad If such a station is not available you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis 29 Intel Desktop Board DH61CR Product Guide Installation Precautions When you install and test the Intel Desktop Board observe all warnings and cautions in the installation instructions To avoid injury be careful of e Sharp pins on connectors e Sharp pins on printed circuit assemblies e Rough edges and sharp corners on the chassis e Hot components such as processors voltage regulators and heat sinks e Damage to wires that could cause a short circuit Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel Prevent Power Supply Overload Do not overload the power supply output To avoid overloading the power supply make sure that the calculated total current loads of all the modules within the computer is less than the output current rating of each of the power supplies output circuits plus enough headroom for desktop board power consumption Observe Safety and Regulatory
59. out installing drivers during installation Both Microsoft Windows Vista and Microsoft Windows 7 include the necessary RAID drivers for both AHCI and RAID without the need to install separate RAID drivers using the F6 switch in the operating system installation process 19 Intel Desktop Board DH61CR Product Guide Intel Rapid Recover Technology Intel RRT The board incorporates Intel Rapid Recover Technology Intel RRT Intel RRT is a feature of Intel RST Intel RRT uses RAID 1 mirroring functionality to copy data from a designated master drive to a designated recovery drive The master drive data can be copied to the recovery drive either continuously or on request When using the continuous update policy changes made to the data on the master drive while the recovery drive is disconnected or offline are automatically copied to the recovery drive when it is reconnected When using the on request update policy the master drive data can be restored to a previous state by copying the data on the recovery drive back to the master drive Expandability Intel Desktop Board DH61CR provides the following expansion capability e One PCI Express 2 0 x16 interface e Two PCI Express 2 0 x1 interfaces e One Conventional PCI bus interface Legacy I O The board s Legacy I O Controller provides the following legacy features e PS 2 back panel connector for mouse keyboard support e One serial port header e One parallel port connecto
60. ponsabilidad medioambiental Intel ha implantado el programa de reciclaje de productos Intel que permite que los consumidores al detalle de los productos Intel devuelvan los productos usados en los lugares seleccionados para su correspondiente reciclado Consulte la http intel com intel other ehs product ecology para ver los detalles del programa que incluye los productos que abarca los lugares disponibles instrucciones de env o t rminos y condiciones etc Francais Dans le cadre de son engagement pour la protection de l environnement Intel a mis en ceuvre le programme Intel Product Recycling Program Programme de recyclage des produits Intel pour permettre aux consommateurs de produits Intel de recycler les produits us s en les retournant des adresses sp cifi es Visitez la page Web http intel com intel other ehs product ecology pour en savoir plus sur ce programme savoir les produits concern s les adresses disponibles les instructions d exp dition les conditions g n rales etc SES AITITE ete REE SL SUME ATE 7 25 PRT Bh TBE DSR N S TUES U 942Nt38 SHIT S EK 4v TIE US DL 0021 56 EBELE HRA m IAA RIAA CHAM 0741472 08t SB 8 RIS http intel com intel other ehs product_ecology 3223 S TSL Malay Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan pengguna pengguna runcit produk jenama Intel me
61. presentative sample of the newly completed computer 77 Intel Desktop Board DH61CR Product Guide Product Certifications Board Level Certifications Intel Desktop Board DH61CR has the regulatory compliance marks shown in Table 20 Table 20 Regulatory Compliance Marks Description Mark UL joint US Canada Recognized Component mark Includes adjacent UL file number for Intel Desktop Boards E210882 CAA US FCC Declaration of Conformity logo mark for Class B equipment CE mark Declaring compliance to European Union EU EMC directive Low Voltage directive and RoHS directive C Australian Communications Authority ACA and New Zealand Radio Spectrum Management NZ RSM C tick mark Includes adjacent Intel supplier code number N 232 Japan VCCI Voluntary Control Council for Interference mark S Korea KCC Korean Communications Commission mark Includes adjacent KCC certification number CPU DH61CR B Taiwan BSMI Bureau of Standards Metrology and Inspections mark Includes adjacent Intel company number D33025 Printed wiring board manufacturer s recognition mark Consists of a unique UL recognized manufacturer s logo along with a flammability rating solder side China RoHS Environmentally Friendly Use Period Logo This is an example of the symbol used on Intel Desktop Boards and associated collateral The color of the mark may vary depending upon the 0 application The Envir
62. ption In Out Hard Disk Drive Activity LED Power LED 1 Hard disk LED pull up to 5 V Out 2 Front panel LED Out 3 Hard disk active LED Out 4 Front panel LED Out Reset Switch On Off Switch 5 Ground 6 Power switch In 7 Reset switch In 8 Ground Power Not Connected 9 Power Out 110 No pin A NOTE When connecting individual wires from your chassis front panel to the front panel header be sure to observe the connection polarity Positive wires are usually solid color and negative wires are usually white or striped Alternate Front Panel Power LED Header Figure 19 F shows the location of the alternate front panel power LED header Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header If your chassis has a three pin power LED cable connect it to this header Table 10 shows the pin assignments for the alternate front panel header Table 10 Alternate Front Panel Power LED Header Signal Names 2 Nopin 48 Installing and Replacing Desktop Board Components Serial Header Figure 19 G shows the location of the serial header Table 11 shows the pin assignments and signal names for the serial header Table 11 Serial Port Header Signal Names Pin Signal Name i Signal Name DCD Data Carrier Detect RXD Receive Data TXD Transmit Data DTR Data Terminal Ready Ground DSR Data Set Ready RTS Request To Send CTS Clear To Send RI Ring Indicator Key no pin
63. r on the back panel e Serial IRQ interface compatible with serialized IRQ support for Conventional PCI bus systems e Intelligent power management including a programmable wake up event interface e Conventional PCI bus power management support The BIOS Setup program provides configuration options for the Legacy I O controller BIOS 20 The BIOS provides the Power On Self Test POST the BIOS Setup program and the PCI PCI Express and SATA auto configuration utilities The BIOS is stored in the Serial Peripheral Interface SPI Flash memory device The BIOS can be updated by following the instructions in Chapter 3 starting on page 61 Desktop Board Features SATA Auto Configuration If you install a SATA device such as a hard disk drive in your computer the auto configuration utility in the BIOS automatically detects and configures the device for your computer You do not need to run the BIOS Setup program after installing a SATA device You can override the auto configuration options by specifying manual configuration in the BIOS Setup program PCI PCI Express Auto Configuration If you install a Conventional PCI or PCI Express add in card in your computer the PCI PCI Express auto configuration utility in the BIOS automatically detects and configures the resources IRQs DMA channels and I O space for that add in card You do not need to run the BIOS Setup program after you install a Conventional PCI or PCI Express add in c
64. remente csse 30 Installing the I O bied sees ennemi nnnm namen aser 31 Installing and Removing the Desktop Board 32 Installing and Removing a Droceseor 1 0 0000 eene nme enn 33 Installing a PFOCeSSOF s eene aaa aaa ER NK REN NK REN ARATRO ERA 33 InstalliingaProcessorFanHeatSink 37 ConnectingtheProcessorFanHeatSinkCable 37 Removing the Processor 0 001 amaaan 37 Intel Desktop Board DH61CR Product Guide Installing and RemovingSystemMemory 0 Installing KI GEET Ne Ile BR LO Installing and Removing PCIExpressx16GraphicsCards Installing a PCI Express x16 Graphics Card NN Removing a PCI Express x16 Graphics Card Connecting Serial ATA SATA Cables meme nnn Connectin gtothelntemalHeaders haeta Front Panel Audio Header NENNEN NNN S PDIF Header pn Re c ero Er E E RC V PE RR SD s Chassis Intrusion Header aus senemi ayan bedri eek 4927 2 4 294295 bie mi selma tb TPM Header ies vc xaxa xr mas re sra dou ne ea VE RUE R Mita ERR AXE CUR a EX RE SER E Front Panel Header me reco E EXTRA XR Ea dE Alternate Front Panel Power LED Header Serial Header silimi br uf a la ina dalda sia qaqa kama Bm seli ii ra a Front Panel USsB2 0Headers ear Internal Mono SpeakerHeader 000 nenne nennen nn
65. rie necorespunz tor Bateriile trebuie reciclate dac este posibil Depozitarea bateriilor uzate trebuie sa respecte reglement rile locale privind protec ia mediului BHMMAHME Tip HCMONb3OBAHUM 6arapen HeCOOTBOTCTBy OUuJero TUNNA cyujecrTByer PUCK ee B3pbiBa barapen JJOJDKHbI ObITb yTWJIM34DOBa Hbl MO BOS3MOXXHOCTM Mrunuzauug 6arape ZOJDKHa MPOBOAUTCA TIO TIDaBH IaM COOTBETCTBYIOLUUM MECTHbIM TDEOOBAHHAM 57 Intel Desktop Board DH61CR Product Guide A A 58 UPOZORNENIE Ak bat riu vymen te za nespravny typ hroz nebezpecenstvo jej vybuchu Bat rie by sa mali podla moZnosti vzdy recyklovat Likvid cia pouZitych bat ri sa musi vykon vat v s lade s miestnymi predpismi na ochranu Zivotn ho prostredia POZOR Zamenjava baterije z baterijo drugacnega tipa lahko povzroci eksplozijo Ce je mogo e baterije reciklirajte Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi a ANYLADU KEE ER EEN HEET assuuueunas l 2n AIT PRT EE EE u larung EE DE EE HT a U UYARI Yanlis t rde pil takildiginda patlama riski vardir Piller m mk n oldugunda geri d n st r lmelidir Kullanilmis piller yerel evre yasalarina uygun olarak atilmalidir OCTOPOTA BnkopucTOBy TEe 6arapei rpaBWibHOro Tuny HAKLUE icHyBaruMe pA34K BM YXY AKLO MOXJIMBO BAKOpUCTaHi 6arapel CHL yTuni3zyBatu Yrunizayia BAKOPUCTaHUux GarTapeli Mae OYTN BUKOHaHA 3rigHO MicLjeBHx HODM LUO pery7IlOIOTb OXODOHy HOBK
66. s materials of this part is above the limit requirement in SJ T 11363 2006 WHE 7 B BJ PR ESP ia ZR JA Ho n ECK f 45 S P MIRAE EE PR ES P sa rh ARES th n AERA SUB PUB rb IA SOE This table shows where these substances may be found in the supply chain of our electronic information products as of the date of sale of the enclosed product Note that some of the component types listed above may or may not be a part of the enclosed product Figure 25 Intel Desktop Board DH61CR China RoHS Material Self Declaration Table Regulatory Compliance EMC Regulations Intel Desktop Board DH61CR complies with the EMC regulations stated in Table 19 when correctly installed in a compatible host system Table 19 EMC Regulations Regulation Title FCC 47 CFR Part 15 Title 47 of the Code of Federal Regulations Part 15 Subpart B Subpart B Radio Frequency Devices USA ICES 003 Interference Causing Equipment Standard Digital Apparatus Canada EN55022 Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment European Union EN55024 Information Technology Equipment Immunity Characteristics Limits and methods of measurement European Union EN55022 Australian Communications Authority Standard for Electromagnetic Compatibility Australia and New Zealand CISPR 22 Limits and methods of measurement of Radio Disturbance Characteristics of Information Technology Equ
67. safety standards stated in Table 18 when correctly installed in a compatible host system Table 18 Safety Standards Regulation Title CSA UL 60950 1 Information Technology Equipment Safety Part 1 General Requirements USA and Canada EN 60950 1 Information Technology Equipment Safety Part 1 General Requirements European Union IEC 60950 1 Information Technology Equipment Safety Part 1 General Requirements International Battery Caution There is insufficient space on this Desktop Board to provide instructions for replacing and disposing of the Lithium ion coin cell battery For system safety certification the statement below or an equivalent statement is required to be permanently and legibly marked on the chassis near the battery A suitable caution label is included with Intel Desktop Board DH61CR A CAUTION Risk of explosion if the battery is replaced with an incorrect type Batteries should be recycled where possible Disposal of used batteries must be in accordance with local environmental regulations For information about replacing the battery go to page 55 69 Intel Desktop Board DH61CR Product Guide European Union Declaration of Conformity Statement 70 We Intel Corporation declare under our sole responsibility that the product Intel Desktop Board DH61CR is in conformity with all applicable essential requirements necessary for CE marking following the provisions of the European Council
68. see Figure 13 o DIMM 1 iiia A EEEE S Channel A DIMM 2 lila 2 GB 1333 MHz Channel B 2992299222 0M22974 Figure 13 Dual Channel Memory Configuration Example 38 Installing and Replacing Desktop Board Components Installing DIMMs To make sure you have the correct DIMM place it on the illustration of the DDR3 DIMM in Figure 14 All the notches should match with the DDR3 DIMM DDR3 cm 1 2 3 4 5 6 8 9 10 11 12 13 0M21949 Figure 14 Use DDR3 DIMMs 39 Intel Desktop Board DH61CR Product Guide 40 To install a DIMM follow these steps 1 2 3 8 9 Observe the precautions in Before You Begin on page 29 Turn off all peripheral devices connected to the computer Turn off the computer and disconnect the AC power cord Remove the computer s cover and locate the DIMM sockets see Figure 15 If a full length PCI Express graphics card is installed in the PCI Express x16 connector remove the card to gain full access to the DIMM sockets 2932222222 OM22962 Figure 15 Installing a DIMM Make sure the clips at either end of the DIMM socket s are pushed outward to the open position Holding the DIMM by the edges remove it from its anti static package Position the DIMM above the socket Align the small notch at the bottom edge of the DIMM with the keys in the socket see inset in Figure 15 Insert the bottom edge of the DIMM into the socket When the DIMM is inserted push do
69. tal bracket to the chassis back panel Push the card ejector lever down using the tip of a pencil or similar tool Figure 17 B in the notch This will release the card from the connector C Pull the card straight up to remove it 0M22964 Figure 17 Removing a PCI Express x16 Graphics Card 43 Intel Desktop Board DH61CR Product Guide Connecting Serial ATA SATA Cables SATA cables support the Serial ATA protocol Each cable can be used to connect one internal SATA drive to the Desktop Board For correct cable function 1 Observe the precautions in Before You Begin on page 29 2 Attach one end of the SATA cable to one of the SATA connectors on the board Figure 18 A and attach the other end of the cable to the SATA drive Figure 18 B m Om OM22965 Figure 18 Connecting a Serial ATA Cable 44 Installing and Replacing Desktop Board Components Connecting to the Internal Headers Before connecting cables to any of the internal headers observe the precautions in Before You Begin on page 29 Figure 19 shows the location of the internal headers and connectors on Intel Desktop Board DH61CR A HD Audio AC 97 Audio S PDIF Sense2_Ret Port2L AUD_GND FP_OUT_L Ground Key no pin Sense_Send Key no pin No Connection S PDIF Out Sense1_Ret Port2R OR AUD GND FP_OUT_R Key no pin Presenceit PortIR PRESENCE MIC_BIAS 5 VDC Ground Port1L AUD_GND MIC Internal Mono Speaker Header ES ZS SI
70. up Support When the PME signal on the Conventional PCI bus is asserted the computer wakes from an ACPI S3 S4 or S5 state PCI Express WAKE Signal Wake up Support When the WAKE signal on a PCI Express bus add in card is asserted the computer wakes from an ACPI S3 S4 or S5 state Wake from Serial Devices Serial port activity wakes the computer from an ACPI S3 state 26 Desktop Board Features Wake from PS 2 Devices PS 2 device activity wakes the computer from an ACPI S3 state Onboard Speaker A speaker is mounted on the Desktop Board The speaker provides audible error code beep code information during the Power On Self Test POST Refer to Appendix A for a description of the beep codes that may be generated during the POST Real Time Clock Subsystem Note A coin cell battery CR2032 powers the real time clock and CMOS memory When the computer is not plugged into a wall socket the battery has an estimated life of three years When the computer is plugged in the standby current from the power supply extends the life of the battery The clock is accurate to 13 minutes year at 25 C with standby power applied by the power supply NOTE If the battery and AC power fail date and time values will be reset and the user will be notified during the POST When the battery voltage drops below a certain level the BIOS Setup program settings stored in CMOS RAM for example the date and time might not be ac
71. wn on the top edge of the DIMM until the retaining clips snap into place Make sure the clips are firmly in place 10 Reinstall the PCI Express graphics card if one was removed in Step 4 11 Replace the computer s cover and reconnect the AC power cord Installing and Replacing Desktop Board Components Removing DIMMs To remove a DIMM follow these steps DT e Pe e 9 Observe the precautions in Before You Begin on page 29 Turn off all peripheral devices connected to the computer Turn off the computer Remove the AC power cord from the computer Remove the computer s cover If a full length PCI Express graphics card is installed in the PCI Express x16 connector remove the card to gain access to the DIMMs Gently spread the retaining clips at each end of the DIMM socket The DIMM pops out of the socket Hold the DIMM by the edges lift it away from the socket and store it in an anti static package Reinstall the PCI Express graphics card if one was removed in Step 5 and reconnect any other parts you removed or disconnected to reach the DIMMs Replace the computer s cover and reconnect the AC power cord Installing and Removing PCI Express x16 Graphics Cards Installing a PCI Express x16 Graphics Card A CAUTION A Before installing a PCI Express x16 graphics card make sure that the tabs on the DIMM sockets are in the upright position closed otherwise they may be damaged by the PCI Express card during inst

Download Pdf Manuals

Related Search

Related Contents

取扱説明書  Husky H4430 Installation Guide  Installation manual Washer-Dryer WD4130, WD4240  Elegant Home Fashions HD7BR756 Instructions / Assembly  複写機及び複合機の表示基準 - JBMIA（一般社団法人 ビジネス機械  Mode d`emploi Naída  SERVICES GUIDE - HSN.com Images server  the Report - Visual Editor Home    Mod: DPA/CVV15  

Copyright © All rights reserved. Failed to retrieve file