Chief JWDSKUB flat panel wall mount
Contents
1. Steel Stud Drywall Plastic Cap Plastic Straps Anchor Metal Channel SIDE VIEW Figure 5 11 Place mount over anchors and align mounting holes in display mount with holes in anchors See Figure 6 12 Place flat washer E onto Phillips pan head screws D 13 Insert 1 4 20 x 1 3 4 Phillips pan head screw D with flat washer E through mounting hole in display mount and into anchor F and tighten until flush against mount DO NOT overtighten WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Overtightening of mounting hardware can damage the steel studs DO NOT overtighten mounting hardware Steel Stud Drywall E x4 D x4 A Display Mount Anchor Metal Channel SIDE VIEW Figure 6 Display Installation 1 NOTE NOTE 1 Determine mounting pattern on display WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT DO NOT substitute hardware Use only hardware supplied by manufacturer WARNING IMPROPER INSTALLATION CAN LEAD TO ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT Screw length must not exceed the depth of threaded mounting insert in display WARNING OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT D2. corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this kit is attached can support five times the combined weight of all equipment WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 75 Ibs 34 01 kg Hex Head Wrench Llave de cabeza hexagonal Sechskantschlussel Chave de cabega sextavada Chiave esagonale 9 Zeskantsleutel Cl t te hexagonale Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier
3. JWDSK Series Installation Instructions 10 Installation Instructions JVVDSR Series 11 JWDSK Series Installation Instructions Le H E IF USA International A 8401 Eagle Creek Parkway Savage MN 55378 FA P 800 582 6480 952 894 6280 Our Mounts Your Vision F 877 894 6918 952 894 6918 Chief Manufacturi divisi f Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands hief Manufacturing a division o P 31 0 40 2668620 Milestone AV Technologies Inc F 31 0 40 2668615 Asia Pacific A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA 8832 000220 RevC 2008 Milestone AV Technologies AIIP RA RAEE AIS DAR 24F P 86 755 8996 9226 DE dc F 86 755 8996 9217 FO JA na A S Osr Consumer
4. Tournevis pointe cruciforme Installation Instructions JVVDSR Series TOOLS REQUIRED FOR INSTALLATION AND PARTS Interface Brachet Rit Including Hardware x1 G 1 3 16 4 8 32 x 3 8 D 4 7 1149 1 4 20 x 1 3 4 1 4 20 SNAP TOGGLE BB JWDSK Series Installation Instructions Site Requirements WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation It should also be noted that no other equipment should be mounted to the same stud 16 or 24 on center Studs Display Mount Installation Location Must be centered on stud If back side of wall is unfinished drywall must be installed to a minimum of one stud left and right of the stud s being used to install the mount Drywall must be secured to studs with screws 12 on center There must be a minimum of 1 7 8 48mm clearance inside wall 1 2 minimum Drywall Thickness Both Sides of Stud Steel Stud 2 x 4 25ga minimum Stud type and structural strength must conform to the Nor
5. INSTALLATION INSTRUCTIONS Medium Flat Panel Steel Stud Wall Mount Our Mounts Your Vision JWDSK Series Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Centris are trademarks of Milestone AV Technologies Inc All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the
6. O NOT over tighten screws when installing interface bracket If the display being installed has a 100x100 VESA mounting pattern no interface bracket is required and the display can be mounted directly to the mounting plate as outlined below If the display being installed requires an interface bracket refer to the interface bracket installation instructions WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes Ensure that screws are not too long WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of mounting plate Start two M4 x 12mm Phillips pan head screws included in hardware kit into upper mounting holes in display back See Figure 7 NOTE Leave at least 1 8 of each screw protruding out back of display Installation Instructions JWDSK Series CAUTION Ensure that adequate cable slack exists for movement of display and that cables will not be pinched by installation of cover B or screws C 2 Carefully insert cables in cavity located in lower portion of mount arm See Figure 9 3 Using Phillips screwdriver install cover B
7. th American Specification for the Design of Cold Formed Steel Structural Members 362 S 125 18 C Shaped S Stud Section Figure 1 Installation Instructions JWDSK Series MOUNT INSTALLATION After determining the site meets the installation requirements Drywall 1 Identify desired mounting location on wall 2 Using a stud finder or similar method locate studs Plastic Straps 3 Align mounting holes in mount with studs making sure mounting holes are centered on studs See Figure 2 4 Mark location of three mounting holes on wall 5 Drill four 1 2 613mm holes See Figure 2 1 2 13mm x4 Figure 3 7 Holding plastic straps on anchor F pull anchor away from wall until channel rests flush behind wall making sure anchor channel is positioned vertically on stud as show in figures below See Figure 4 8 Slide plastic cap on anchor F towards wall until flange of cap is flush with wall See Figure 4 Steel Stud Drywall Plastic Cap Anchor Metal Channel Mounting holes centered on studs SIDE VIEW Figure 4 Figure 2 a 9 Snap off plastic straps on anchor at wall by pushing side to 6 Hold metal channel on anchor F flat alongside plastic side snapping off straps level with flange of plastic cap strapsandslidechannelthroughhole SeeFigure3 See Figure 5 10 Repeat steps 6 through 9 for each mounting hole JWDSK Series Installation Instructions
8. with two screws C See Figure 9 Cable Path Figure 7 typical 2 Align two screws in display back with upper teardrop mounting holes in mounting plate B x2 3 Place two screws in display back into upper teardrop mounting holes in display mounting plate and lower display C x4 until screws are seated in lower area of teardrop mounting holes See Figure 8 4 Install two screws through display mounting plate and into lower mounting holes in display back See Figure 8 l 5 Tighten all hardware Figure 9 ADJUSTMENTS Swing Arm PIVOT SWING 1 Using 3 16 hex kev G slightiv loosen or tighten the adjustment screw s as necessarv See Figure 10 Adjustment Screws Figure 10 Figure 8 6 Route cables and wires to display CABLE MANAGEMENT 1 Attach all cables to display JWDSK Series Installation Instructions Adjust display Roll Pitch and YAW tension Disconnect all wires and cable from the display Loosen two Upper screws securing display Lift display upward and away from mount Using a hex head wrench turn the tension adjustment screw clockwise to increase tension or counter clockwise to decrease tension See Figure 11 6 Re install display SAONA Figure 11 Remove two Lower screws securing display to Centris cup Installation Instructions JVVDSR Series
Download Pdf Manuals
Related Search