Cisco C3KX-NM-10G= network media converter
Contents
1. MAST Master The stack master status STACK Stack member status StackWise port status The stack member status The Stack Wise port status See the Stack LED Catalyst 3750 X section on page 1 12 PoE PoE port power 1 Only Catalyst 3750 X switches 2 Only switches with PoE ports Table 1 9 Port Mode Port LED Color The PoE port status Meaning of Switch LED Colors in Different Modes STAT port status Off No link or port was administratively shut down Green Link present no activity Blinking green Activity Port is sending or receiving data Alternating green amber Link fault Error frames can affect connectivity and errors such as excessive collisions CRC errors and alignment and jabber errors are monitored for a link fault indication Amber Port is blocked by Spanning Tree Protocol STP and is not forwarding data After a port is reconfigured the port LED can be amber for up to 30 seconds as STP checks the switch for possible loops SPEED 10 100 1000 ports Off Port is operating at 10 Mb s Green Port is operating at 100 Mb s Single green flash on for 100 ms off for 1900 ms Port is operating at 1000 Mb s Network module sl ots Off Port is not operating Blinking green Port is operating at up to 10 Gb s Catalyst 3750 X and 3560 X Switch Hardware Installation Guide OL 12. cuaecee i Product Overview The Catalyst 3750 X and 3560 X series switches are Ethernet switches to which you can connect devices such as Cisco IP Phones Cisco Wireless Access Points workstations and other network devices such as servers routers and other switches The Catalyst 3750 X switches support stacking through Cisco StackWise technology and power management through StackPower The Catalyst 3560 X switches do not support switch stacking or StackPower Unless otherwise noted the term switch refers to a standalone switch and to a switch stack e Switch Models page 1 1 e Front Panel Description page 1 3 e Rear Panel Description page 1 15 e Management Options page 1 21 Switch Models Table 1 1 Catalyst 3750 X Switch Models Switch Model Cisco 10S Image Description Catalyst 3750 X 24T L LAN Base image 24 10 100 1000 Ethernet ports Stack Wise Plus 1 network module slot 350 W power supply Catalyst 3750 X 48T L LAN Base image 48 10 100 1000 Ethernet ports StackWise Plus one network module slot 350 W power supply Catalyst 3750 X 24P L LAN Base image 24 10 100 1000 PoE ports StackWise Plus 1 network module slot 715 W power supply Catalyst 3750 X 48P L_ LAN Base image 48 10 100 1000 PoE ports StackWise Plus one network module slot 715 W power supply Catalyst 3750 X 48PF L LAN Base image 48 10 100 1000 PoE ports StackWise Plus 1 network module slot 1100 W power supply Cata
3. 100 GHz ITU grid DWDM SFP 5012 DWDM SFP 1550 12 nm SFP 100 GHz ITU grid DWDM SFP 5092 DWDM SFP 1550 92 nm SFP 100 GHz ITU grid DWDM SFP 5172 DWDM SFP 1551 72 nm SFP 100 GHz ITU grid DWDM SFP 5252 DWDM SFP 1552 52 nm SFP 100 GHz ITU grid DWDM SFP 5332 DWDM SFP 1553 33 nm SFP 100 GHz ITU grid DWDM SFP 5413 DWDM SFP 1554 13 nm SFP 100 GHz ITU grid DWDM SFP 5494 DWDM SFP 1554 94 nm SFP 100 GHz ITU grid DWDM SFP 5575 DWDM SFP 1555 75 nm SFP 100 GHz ITU grid DWDM SFP 5655 DWDM SFP 1556 55 nm SFP 100 GHz ITU grid DWDM SFP 5736 DWDM SFP 1557 36 nm SFP 100 GHz ITU grid DWDM SFP 5817 DWDM SFP 1558 17 nm SFP 100 GHz ITU grid DWDM SFP 5898 DWDM SFP 1558 98 nm SFP 100 GHz ITU grid DWDM SFP 5979 DWDM SFP 1559 79 nm SFP 100 GHz ITU grid DWDM SFP 6061 DWDM SFP 1560 61 nm SFP 100 GHz ITU grid DWDM SFP 6141 DWDM SFP 1561 42 nm SFP 100 GHz ITU grid 1 Not supported for NEBS 2 DOM digital optical monitoring Table 1 5 Part Number Description Cisco SFP Modules Supported for the 3750 X and 3560 X Switches SFP 10G LR 10 GBASE LR SFP transceiver module for SMF 1350 nm LC duplex connector SFP 10G SR 10 GBASE SR SFP transceiver module for MMF 850 nm LC duplex connector SFP 10G LRM 10 GBASE LRM SFP module for MM
4. 715 W power supply provides up to 8 7 W of PoE to all ports The power supply modules have two status LEDs Table 1 18 Switch Power Supply Module LEDs AC Power Supply Module LEDs AC OK Description PS OK Description Off No AC input power Off Output is disabled or input is outside operating range AC LED is off Green AC input power present Green Power output to switch active Red Output has failed DC Power Supply Module LEDs DC OK Description PS OK Description Off No DC input power Off Output is disabled or input is outside operating range DC LED is off Green DC input power present Green Power output to switch active Red Output has failed Catalyst 3750 X and 3560 X Switch Hardware Installation Guide is E OL 19593 01 Chapter1 Product Overview Fan Modules Rear Panel Description W For information about replacing a power supply module wiring a DC power supply module and module specifications see Chapter 3 Power Supply and Fan Module Installation and Appendix A Technical Specifications The switch has two internal hot swappable 12 V fan modules each with two fans The air circulation system consists of the fan modules and the power supply modules The airflow patterns vary depending on the power supply configuration Figure 1 8 shows the airflow patterns for the 24 and 48 port switches The blue arrow shows cool air flow and the red arrow shows war
5. Catalyst 3560 X 48T L LAN Base image 48 10 100 1000 Ethernet ports 1 network module slot 350 W power supply Catalyst 3560 X 24P L LAN Base image 24 10 100 1000 PoE ports 1 network module slot 715 W power supply Catalyst 3560 X 48P L_ LAN Base image 48 10 100 1000 PoE ports 1 network module slot 715 W power supply Catalyst 3560 X 48PF L LAN Base image 48 10 100 1000 PoE ports 1 network module slot 1100 W power supply Catalyst 3560 X 24T S IP Base image 24 10 100 1000 Ethernet ports 1 network module slot 350 W power supply Catalyst 3560 X 48T S IP Base image 48 10 100 1000 Ethernet ports 1 network module slot 350 W power supply Catalyst 3560 X 24P S _ IP Base image 24 10 100 1000 PoE ports 1 network module slot 715 W power supply Catalyst 3560 X 48P S IP Base image 48 10 100 1000 PoE ports 1 network module slot 715 W power supply Catalyst 3560 X 48PF S IP Base image 48 10 100 1000 PoE ports 1 network module slot 1100 W power supply 1 Available network modules 10 Gigabit Ethernet network module 1 Gigabit Ethernet network module blank module see Table 1 3 on page 1 5 2 PoE Power over Ethernet plus provides up to 30 W per port Catalyst 3750 X and 3560 X Switch Hardware Installation Guide OL 19593 01 Chapter1 Product Overview Front Panel Description W 3 You can upgrade to the IP Services feature set when you order the switch Front Panel Description The
6. See the switch software configuration guide on Cisco com for network configuration concepts and examples of using the switch to create dedicated network segments and interconnecting the segments through Gigabit Ethernet connections Catalyst 3750 X and 3560 X Switch Hardware Installation Guide P22 OL 19593 01
7. link The SFP module in Slot 2 does not operate When the SFP module in Slot 1 is shutdown loses link or is removed the SFP module in Slot 2 becomes operational At this point the SFP module in Slot 1 will not become operational under any circumstance for as long as an SFP module remains in Slot 2 whether it is link up or not The same precedence applies to Slots 3 and 4 1 All network modules are hot swappable For information about the network modules see the Installing a Network Module in the Switch section on page 2 21 For cable specifications see Appendix B Connector and Cable Specifications SFP and SFP Modules The switch Gigabit Ethernet SFP and SFP modules provide copper or fiber optic connections to other devices These transceiver modules are field replaceable providing the uplink interfaces when installed in an SFP module slot The SFP modules have LC connectors for fiber optic connections or RJ 45 connectors for copper connections Use only Cisco SFP modules on the switch Catalyst 3750 X and 3560 X Switch Hardware Installation Guide OL 19593 01 gois Chapter 1 Product Overview W Front Panel Description Table 1 4 Part Number Cisco SFP Modules Supported for the 3750 X and 3560 X Switches Description GLC GE 100FX 100FX SFP on GE SFP ports for LAN switches GLC LH SM GE SFP LC connector LX LH transceiver GLC SX MM GE SFP LC connector
8. switch front panel includes a USB Type B console port the 10 100 1000 Ethernet ports or the 10 100 1000 PoE ports the network module and the switch LEDs Figure 1 1 shows the Catalyst 3750 X 48 PoE switch as an example All the Catalyst 3750 X and 3560 X switches have similar components Figure 1 1 Switch Front Panel 1 Mode button 4 10 100 1000 ports 2 USB Type B console port 5 Network Module 3 Status LEDs 10 100 1000 Ethernet Ports PoE Ports The 10 100 1000 Ethernet ports use RJ 45 connectors with Ethernet pinouts The maximum cable length is 328 feet 100 meters The 100BASE TX and 1000BASE T traffic requires Category 5 Category 5e or Category 6 unshielded twisted pair UTP cable The 10BASE T traffic can use Category 3 or Category 4 UTP cable For information about the 10 100 1000 Ethernet port connections and specifications see the 10 100 1000 Ethernet Port Connections section on page 2 26 and Appendix B Connector and Cable Specifications The PoE ports use the same connectors as described in the previous section and provide this support e Support for IEEE 802 3af compliant powered devices up to 15 4 W e Support for IEEE 802 3at compliant powered devices up to 30 W e Support for Cisco enhanced PoE e Support for prestandard Cisco powered devices OL 19593 01 Catalyst 3750 X and 3560 X Switch Hardware Installation Guide jg Chapter1 Product Overview W Front Pane
9. 9593 01 Product Overview USB Console LED Front Panel Description Table 1 9 Meaning of Switch LED Colors in Different Modes continued Port Mode Port LED Color Meaning DUPLX Off Port is operating in half duplex duplex Green Port is operating in full duplex MAST Off The switch is not the stack master data stack Note For a standalone switch this LED is off master Green The switch is the stack master Amber Error during stack master election STACK Off No stack member corresponding to that member number stack member Blinking green Stack member number Green Member numbers of other stack member switches PoE Off PoE is off If the powered device is receiving power from an AC power source the port LED is off even if the device is connected to the switch port Green PoE is on The port LED is green when the switch port is providing power Alternating PoE is denied because providing power to the powered device will green and exceed the switch power capacity amber Blinking amber PoE is off due to a fault or because it has exceeded a limit set in the switch software A Caution PoE faults are caused when noncompliant cabling or powered devices are connected to a PoE port Use only standard compliant cabling to connect Cisco prestandard IP Phones and wireless access points or IEEE 802 3af compliant devices to PoE ports You must remove from the networ
10. ED 4 Speed LED 9 Stack LED 5 Duplex LED 10 PoE LED 1 XPS Expandable power system Catalyst 3750 X and 3560 X Switch Hardware Installation Guide OL 19593 01 Chapter1 Product Overview Front Panel Description W 2 Only Catalyst 3750 X switches 3 Only switches with PoE ports System LED Table 1 6 System LED Color System Status Off System is not powered on Green System is operating normally Blinking Green Switch is running power on self test POST Blinking Amber There is a fault with one of the following e Network module non traffic related e Power supply e Fan module Amber System is receiving power but is not functioning properly For information on the System LED colors during power on self test POST see the Diagnosing Problems section on page 4 1 XPS LED Table 1 7 XPS LED Color XPS Status Off XPS cable is not installed Switch is in StackPower mode Catalyst 3750 X Green XPS is connected and ready to provide back up power Blinking green XPS is connected but is unavailable because it is providing power to another device redundancy has been allocated to a neighboring device Amber The XPS is in standby mode or in a fault condition See the XPS 2200 documentation for information about the standby mode and fault conditions Blinking amber The power supply in a switch has failed and the XPS is providing power to t
11. F and SMF 1310 nm SFP H10GB CU1M meter 10 GBASE CU Twinax SFP cable assembly 1 OL 19593 01 Catalyst 3750 X and 3560 X Switch Hardware Installation Guide Chapter1 Product Overview W Front Panel Description LEDs Table 1 5 Cisco SFP Modules Supported for the 3750 X and 3560 X Switches Part Number Description SFP H10GB CU3M 10 GBASE CU Twinax SFP cable assembly 3 meters SFP H10GB CUS5SM 10 GBASE CU Twinax SFP cable assembly 5meters For information about SFP modules see your SFP module documentation and the Installing SFP and SFP Modules section on page 2 23 For cable specifications see Appendix B Connector and Cable Specifications amp Note When ordering or using CX1 cables ensure that the version identifier is 2 or higher The Catalyst 3560 X switch supports the SFP module patch cable CAB SFP 50CM a 0 5 meter copper passive cable with SFP module connectors at each end This cable is only used with 1 Gigabit Ethernet SFP ports to connect two Catalyst 3560 X switches in a cascaded configuration You can use the switch LEDs to monitor switch activity and its performance Figure 1 2 shows the Catalyst 3750 X switch LEDs and the Mode button that you use to select a port mode Figure 1 2 Switch Front Panel LEDs 1 System LED 6 USB console port LED 2 XPS LED 7 S PWR StackPower LED 3 Status LED 8 Master L
12. SX transceiver GLC T 1000BASE T SFP transceiver module for copper connections GLC ZX SM 1000BASE ZX SFP module for SMF 1550 nm GLC BX D 1000BASE BX10 SFP module for single strand SMF 1490 nm TX 1310 nm RX wavelength GLC BX U 1000BASE BX10 SFP module for single strand SMF 1310 nm TX 1490 nm RX wavelength CWDM SFP 1470 CWDM 1470 nm SFP Gigabit Ethernet and 1G 2G FC CWDM SFP 1490 CWDM 1490 nm SFP Gigabit Ethernet and 1G 2G FC CWDM SFP 1510 CWDM 1510 nm SFP Gigabit Ethernet and 1G 2G FC CWDM SFP 1530 CWDM 1530 nm SFP Gigabit Ethernet and 1G 2G FC CWDM SFP 1550 CWDM 1550 nm SFP Gigabit Ethernet and 1G 2G FC CWDM SFP 1570 CWDM 1570 nm SFP Gigabit Ethernet and 1G 2G FC CWDM SFP 1590 CWDM 1590 nm SFP Gigabit Ethernet and 1G 2G FC CWDM SFP 1610 CWDM 1610 nm SFP Gigabit Ethernet and 1G 2G FC SFP GE S 1000BASE SX SFP module for MMF 850 nm DOM SFP GE L 1000BASE LX LH SFP module for SMF 1300 nm DOM DWDM SFP 3033 DWDM SFP 1530 33 nm SFP 100 GHz ITU grid DWDM SFP 3112 DWDM SFP 1531 12 nm SFP 100 GHz ITU grid DWDM SFP 3190 DWDM SFP 1531 90 nm SFP 100 GHz ITU grid DWDM SFP 3268 DWDM SFP 1532 68 nm SFP 100 GHz ITU grid DWDM SFP 3346 DWDM SFP 1533 47 nm SFP 100 GHz ITU grid DWDM SFP 3425 DWDM SFP 1534 25 nm SFP 100 GHz ITU grid DWDM SFP 3504 DWDM SFP 1535 04 nm SFP 100 GHz ITU gr
13. a 0 5 meter StackWise cable CAB STACK 50CM that you can use to connect the Stack Wise ports Caution Use only approved cables CAB STACK 50CM CAB STACK 1IM CAB STACK 3M CAB STACK 50CM NH CAB STACK 1M NH or CAB STACK 3M NH and connect only to similar Cisco equipment Equipment might be damaged if connected to nonapproved Cisco cables or equipment You can order these StackWise cables from your Cisco sales representative e CAB STACK 50CM 0 5 meter cable e CAB STACK 1M l meter cable e CAB STACK 3M 3 meter cable Catalyst 3750 X and 3560 X Switch Hardware Installation Guide Pie OL 19593 01 _ Chapter 1 Product Overview Rear Panel Description W e CAB STACK 50CM NH 0 5 meter cable nonhalogen e CAB STACK 1IM NH l meter cable nonhalogen e CAB STACK 3M NH 3 meter cable nonhalogen Power Supply Modules The 24 and 48 port switches are powered through one or two internal power supply modules The Switch Power Supply Modules section on page 1 17 and Table 1 16 describe the supported power supply modules Switch Power Supply Modules A The switch has two internal power supply module slots You can use two AC modules two DC modules a mixed configuration of one AC and one DC power supply module or one power supply module and a blank module The switch can operate with either one or two active power supply modules or with power supplied by an XPS 2200 A Catalyst 3750 X switch that is in
14. a StackPower stack can operate with power supplied by other switches in the stack Table 1 1 and Table 1 2 show the power supply modules that ship with each switch model All power supply modules except the blank modules have internal fans All switches ship with a blank power supply module in the second power supply slot Caution Do not operate the switch with one power supply module slot empty For proper chassis cooling both power supply module slots must be populated The 350 W and 715 W AC power supply modules are autoranging units that support input voltages between 100 and 240 VAC The 1100 W power supply module is an autoranging unit that supports input voltages between 115 and 240 VAC The 440 W DC power supply module has dual input feeds A and B and supports input voltages between 36 and 72 VDC The output voltage range is 51 57 V Each AC power supply module has a power cord for connection to an AC power outlet The 1100 W and 715 W modules use a 16 AWG cord only North America All other modules use an 18 AWG cord The DC power supply module must be wired to a DC power source The XPS 2200 powers connected switches when the power supply is removed or fails When a new switch power supply is installed the switch software polls the device The switch power supply again provides power and the XPS 2200 is available to power other devices Table 1 16 shows the power supply modules available for Catalyst 3750 X and 3560 X sw
15. ector on the front panel is available for switch management Figure 1 5 Figure 1 5 USB Mini Type B Console Port 253163 See the Management Ports section on page 1 20 for details Catalyst 3750 X and 3560 X Switch Hardware Installation Guide iis OL 19593 01 Chapter 1 Product Overview Rear Panel Description W Rear Panel Description The switch rear panel has a ground connector an RJ 45 console port an RJ 45 10 100 management port a USB Type A connector two Stack Wise connectors only Catalyst 3750 X switches two fan modules an XPS 2200 connector a StackPower connector only Catalyst 3750 X switches and two power supply module slots See Figure 1 6 and the descriptions on the following pages Figure 1 6 shows the Catalyst 3750 X 48 PoE switch which has one connector for either a StackPower or an XPS connection and one connector only for StackPower Figure 1 7 shows the Catalyst 3560 X switch rear panel which has one connector for XPS and no StackPower connector Figure 1 6 Catalyst 3750 X Switch Rear Panel 1 Ground connector 8 Fan modules 2 IRJ 45 console port LED 9 StackPower or XPS 2200 connector 3 RJ 45 console port 10 StackPower connector 4 RJ 45 10 100 management port 11 Power supply modules AC power supply modules shown 5 USB Type A connector 12 AC power input status LED 6 Stack cable connectors 13 Power supply output status LED 7 Reset butt
16. escription W Table 1 3 Network Modules Network Module Description Blank This module has no uplink ports 1 Gigabit Ethernet This module has four 1 Gigabit SFP module slots Any combination of standard SFP modules are supported SFP modules are not supported If you insert an SFP module in the 1 Gigabit network module the SFP module does not operate and the switch logs an error message 10 Gigabit Ethernet This module has four slots Two slots support only 1 Gigabit SFP modules two slots support either 1 Gigabit SFP or 10 Gigabit SFP modules The four slots are grouped as two pairs with each pair consisting of one SFP slot and one SFP slot Each pair supports either two 1 Gigabit SFP modules or one 10 Gigabit SFP module A 10 Gigabit SFP module cannot operate at the same time as the corresponding 1 Gigabit SFP module in the pair Supported combinations of SFP and SFP modules e Slots 1 2 3 and 4 populated with 1 Gigabit SFP modules e Slots 1 and 2 populated with 1 Gigabit SFP modules and Slot 4 populated with one 10 Gigabit SFP module e Slot 2 populated with one 10 Gigabit SFP module and Slots 3 and 4 populated with 1 Gigabit SFP modules e Slot 2 and Slot 4 each populated with 10 Gigabit SFP modules A 10 Gigabit SFP module takes precedence over a 1 Gigabit SFP module except when an SFP module is first inserted in Slot 1 and has link When you insert an SFP module in Slot 2 the SFP in Slot 1 retains
17. hat switch redundancy has been allocated to this device Port LEDs and Modes Each Ethernet port and 10 Gigabit Ethernet module slot has a port LED These port LEDs as a group or individually display information about the switch and about the individual ports The port mode determines the type of information shown by the port LEDs Table 1 8 lists the mode LEDs and their associated port modes and meanings To select or change a mode press the Mode button until the desired mode is highlighted When you change port modes the meanings of the port LED colors also change Table 1 9 explains how to interpret the port LED colors in different port modes Catalyst 3750 X and 3560 X Switch Hardware Installation Guide OL 19593 01 Chapter1 Product Overview W Front Panel Description When you press the Mode button on any switch in the Catalyst 3750 X switch stack all the stack switches change to show the same selected mode For example if you press the Mode button on the stack master to show the SPEED LED all the other switches in the stack also show the SPEED LED Table 1 8 Mode LED Port Mode LEDs Port Mode Description STAT Port status The port status This is the default mode SPEED Port speed The port operating speed 10 100 or 1000 Mb s DUPLX Port duplex mode The port duplex mode full duplex or half duplex The 10 100 1000 ports operate only in full duplex mode Note
18. id DWDM SFP 3582 DWDM SFP 1535 82 nm SFP 100 GHz ITU grid DWDM SFP 3661 DWDM SFP 1536 61 nm SFP 100 GHz ITU grid DWDM SFP 3739 DWDM SFP 1537 40 nm SFP 100 GHz ITU grid DWDM SFP 3819 DWDM SFP 1538 19 nm SFP 100 GHz ITU grid DWDM SFP 3898 DWDM SFP 1538 98 nm SFP 100 GHz ITU grid DWDM SFP 3977 DWDM SFP 1539 77 nm SFP 100 GHz ITU grid DWDM SFP 4056 DWDM SFP 1540 56 nm SFP 100 GHz ITU grid DWDM SFP 4134 DWDM SFP 1541 35 nm SFP 100 GHz ITU grid DWDM SFP 4214 DWDM SFP 1542 14 nm SFP 100 GHz ITU grid DWDM SFP 4294 DWDM SFP 1542 94 nm SFP 100 GHz ITU grid Catalyst 3750 X and 3560 X Switch Hardware Installation Guide OL 19593 01 _ Chapter 1 Product Overview Table 1 4 Part Number Description Front Panel Description Cisco SFP Modules Supported for the 3750 X and 3560 X Switches continued DWDM SFP 4373 DWDM SFP 1543 73 nm SFP 100 GHz ITU grid DWDM SFP 4453 DWDM SFP 1544 53 nm SFP 100 GHz ITU grid DWDM SFP 4532 DWDM SFP 1545 32 nm SFP 100 GHz ITU grid DWDM SFP 4612 DWDM SFP 1546 12 nm SFP 100 GHz ITU grid DWDM SFP 4692 DWDM SFP 1546 92 nm SFP 100 GHz ITU grid DWDM SFP 4772 DWDM SFP 1547 72 nm SFP 100 GHz ITU grid DWDM SFP 485 1 DWDM SFP 1548 51 nm SFP 100 GHz ITU grid DWDM SFP 493 1 DWDM SFP 1549 32 nm SFP
19. is not selected on a switch with PoE ports the PoE LED still shows detected PoE problems Table 1 13 PoE Mode LED Color PoE Status Off PoE mode is not selected None of the 10 100 1000 ports have been denied power or are in a fault condition Green PoE mode is selected and the port LEDs show the PoE status Blinking amber PoE mode is not selected At least one of the 10 100 1000 ports has been denied power or at least one of the 10 100 1000 ports has a PoE fault Catalyst 3750 X and 3560 X Switch Hardware Installation Guide OL 19593 01 ELEN Chapter1 Product Overview W Front Panel Description Network Module LEDs Figure 1 4 Network Module LEDs 10 Gigabit Network Module Shown 1 G1 LED 3 G3 LED 2 G2 TE1 LED 4 G4 TE2 LED Table 1 14 Network Module LEDs Color Network Module Link Status Off Link is off Green Link is on no activity Blinking green Activity on a link no faults Blinking amber Link is off due to a fault or because it has exceeded a limit set in the switch software A Caution Link faults are caused when noncompliant cabling is connected to an SFP or SFP port Use only standard compliant cabling to connect to Cisco SFP and SFP ports You must remove from the network any cable or device that causes a link fault Amber Link for the SFP or SFP has been disabled USB Mini Type B Port A USB 5 pin mini Type B conn
20. itches and power supply configurations based on switch models Table 1 16 Switch Power Supply Modules 48 Port 24 Port 48 Port PoE 24 Port PoE Non PoE Non PoE Power Supply Module Switch Switch Switch Switch C3KX PWR 1100WAC Primary or spare Spare Spare Spare C3KX PWR 1100WAC JP C3KX PWR 715WAC Spare Primary or spare Spare Spare OL 19593 01 Catalyst 3750 X and 3560 X Switch Hardware Installation Guide Chapter1 Product Overview W Rear Panel Description amp Table 1 16 Switch Power Supply Modules continued 48 Port 24 Port 48 Port PoE 24 Port PoE Non PoE Non PoE Power Supply Module Switch Switch Switch Switch C3KX PWR 350WAC Spare Spare Primary or spare Primary or spare C3KX PWR 440WDC Primary or spare Primary or spare Primary or spare Primary or spare C3KX PSBAY BLNK Blank module Blank module Blank module Blank module 1 For full 15 4 W support on a 48 port PoE switch you must use a C3KX PWR 1100WAC power supply module 2 This module is used only in Japan Table 1 17 Switch Power Supply Requirements for PoE and PoE PoE Option 24 Port Switch 48 Port Switch PoE up to 15 4 W per port 1 715 W power supply 1 1100 W power supply 2 440 W DC power supplies PoE up to 30 W per port 1 1100 W power supply 1 1100 W power supply plus one 715 W power supply or 2 1100 W power supplies Note A 48 port switch with one
21. k any cable or device that causes a PoE fault Amber PoE for the port has been disabled Note PoE is enabled by default 1 Only Catalyst 3750 X switches 2 Only switches with PoE or PoE ports The USB console LED shows whether there is an active USB connection to the port Catalyst 3750 X and 3560 X Switch Hardware Installation Guide Chapter1 Product Overview W Front Panel Description Table 1 10 Color USB Console Port LED Description Off USB console is disabled Green USB console is enabled S PWR LED Catalyst 3750 X Table 1 11 S PWR LED Color Description Off StackPower cable is not connected or the switch is in standalone mode Green An XPS cable is connected to the XPS 2200 Each StackPower port is connected to another switch or to an XPS 2200 Catalyst 3750 X switches Blinking Green This appears on the switch in a StackPower ring configuration that detects an open ring or has only one StackPower cable connected and no connection to an XPS 2200 Amber There is a fault load shedding is occurring a StackPower cable is defective or administrative action is required See the switch software configuration guide for information about configuring StackPower Blinking Amber The StackPower budget is not sufficient to meet current power demands Master LED Catalyst 3750 X Table 1 12 Master LED Colo
22. l Description e Configuration for StackPower PoE When the switch internal power supply module s cannot support the total load StackPower configurations allow the switch to leverage power available from other switches only Catalyst 3750 X switches e Configurable support for Cisco intelligent power management including enhanced power negotiation power reservation and per port power policing Depending on the installed power supply modules each port can deliver up to 30 W of PoE See Table 1 17 for the power supply matrix that defines the available PoE and PoE power per port Note The output of the PoE circuit has been evaluated as a Limited Power Source LPS per IEC 60950 1 For information about power supply modules PoE port connections and PoE specifications see the Power Supply Modules section on page 1 17 the PoE Port Connections section on page 2 26 and Appendix B Connector and Cable Specifications Network Modules The switch has one hot swappable network module that provides SFP and SFP uplink ports to connect to other devices You must insert the network module during switch operation Operating the switch without a network module is not supported A blank module is available The switch generates logs when you insert or remove a network module with SFP ports Catalyst 3750 X and 3560 X Switch Hardware Installation Guide OL 19593 01 Chapter1 Product Overview Front Panel D
23. lyst 3750 X 24T S__ IP Base image 24 10 100 1000 Ethernet ports StackWise Plus StackPower 1 network module slot 350 W power supply Catalyst 3750 X and 3560 X Switch Hardware Installation Guide OL 19593 01 EN Chapter1 Product Overview HI Switch Models Table 1 1 Catalyst 3750 X Switch Models continued Switch Model Cisco 10S Image Description Catalyst 3750 X 48T S__ IP Base image 48 10 100 1000 Ethernet ports StackWise Plus StackPower network module slot 350 W power supply Catalyst 3750 X 24P S__ IP Base image 24 10 100 1000 PoE ports Stack Wise Plus StackPower 1 network module slot 715 W power supply Catalyst 3750 X 48P S _ IP Base image 48 10 100 1000 PoE ports StackWise Plus StackPower 1 network module slot 715 W power supply Catalyst 3750 X 48PF S IP Base image 48 10 100 1000 PoE ports StackWise Plus StackPower 1 network module slot 1100 W power supply 1 Available network modules 10 Gigabit Ethernet network module 1 Gigabit Ethernet network module blank module see Table 1 3 on page 1 5 2 PoE Power over Ethernet plus provides up to 30 W per port 3 You can upgrade to the IP Services feature set when you order the switch Table 1 2 Catalyst 3560 X Switch Models Switch Part Number Description Catalyst 3560 X 24T L LAN Base image 24 10 100 1000 Ethernet ports 1 network module slot 350 W power supply
24. m air flow When the fan modules are operating properly a green LED is on at the top left corner of the fan assembly viewed from the rear If the fan fails the LED turns to amber Figure 1 8 24 and 48 Port Switch Airflow Patterns For information about installing a fan module and the module specifications see Chapter 3 Power Supply and Fan Module Installation and Appendix A Technical Specifications XPS Connector A Warning Attach only the following Cisco external power system to the switch XPS 2200 Statement 387 The Cisco XPS 2200 is a expandable power system that can support nine network switches and provides power to one or two failed switches at a time It senses when the power supply of a connected switch fails and provides power to the failed switch Use the XPS 2200 only with approved Cisco XPS cables You can order these XPS cables for connecting your switch to the XPS 2200 from your Cisco sales representative e CAB XPS 58CM 0 58 meter cable e CAB XPS 150CM 1 5 meter cable The Cisco XPS 2200 has a nominal output level of 56 V The total maximum output power depends on the installed power supply modules OL 19593 01 Catalyst 3750 X and 3560 X Switch Hardware Installation Guide jg Chapter1 Product Overview W Rear Panel Description The nine ports on the XPS 2200 provide the power and management signals to the Catalyst 3750 X and 3560 X switches Other switch models do not
25. ndows PCs need a driver for the USB port See the Installing the Cisco Microsoft Windows USB Device Driver section on page C 3 for installation instructions When the switch detects a valid USB connection to a powered device input from the Ethernet connection is immediately disabled and input from the USB console is enabled Removing the USB connection immediately reenables input from the Ethernet connection An LED on the switch front panel see Figure 1 2 is green when the USB console connection is enabled The switch provides a configurable inactivity timeout that reactivates the RJ 45 console if no input activity has occurred on the USB console for a specified time period After the USB console has been deactivated due to a timeout you can restore its operation by disconnecting and reconnecting the USB cable You can disable USB console operation by using Cisco IOS commands See the switch software configuration guide for details Management Options e Cisco Network Assistant Cisco Network Assistant is a PC based network management GUI application for LANs You can use the GUI to configure and manage switch clusters or standalone switches Cisco Network Assistant is available at no cost and can be downloaded from this URL http www cisco com go networkassistant For information on starting the Network Assistant application see the Getting Started with Cisco Network Assistant guide on Cisco com e Device manager You can use
26. on Figure 1 7 Catalyst 3560 X Switch Rear Panel OL 19593 01 Catalyst 3750 X and 3560 X Switch Hardware Installation Guide E Chapter1 Product Overview W Rear Panel Description 1 Ground connector 7 Fan modules 2 RJ 45 console port LED 8 XPS 2200 connector 3 RJ 45 console port 9 Power supply module slot blank module shown 4 RJ 45 10 100 management port 10 Power supply module AC power supply module shown 5 USB Type A connector 11 AC power input status LED 6 Reset button 12 Power supply output status LED RJ 45 Console Port LED Table 1 15 RJ 45 Console Port LED Color RJ 45 Console Port Status Off RS 232 console is disabled Green RS 232 console is enabled USB Type A Interface The USB Type A interface provides access to external USB FLASH devices also known as thumb drives or USB keys The interface supports Cisco USB flash drives with capacities from 64 MB to 1 GB Cisco IOS software provides standard file system access to the flash device read write erase and copy as well as formatting of the flash device with a FAT file system You can boot the switch from a USB drive For information about the switch management ports see the switch software configuration guide and the command reference on Cisco com and the Connector and Cable Specifications section on page B 1 StackWise Ports A The Catalyst 3750 X switch ships with
27. r Description Off Switch is not the stack master Green Switch is the stack master or a standalone switch Amber An error occurred when the switch was selecting the stack master switch or another type of stack error occurred Stack LED Catalyst 3750 X The stack LED shows the sequence of member switches in a stack Up to nine switches can be members of a stack The first nine port LEDs show the member number of a switch in a stack Figure 1 3 shows the LEDs on the first switch which is stack member number 1 For example if you press the Mode button and select Stack the LED for port 1 blinks green The LEDs for ports 2 and 3 are solid green as these represent the member numbers of other switches in the stack The other port LEDs are off because there are no more members in the stack Catalyst 3750 X and 3560 X Switch Hardware Installation Guide i12 E OL 19593 01 Chapter1 Product Overview Front Panel Description W Figure 1 3 Stack LED 1 Stack member 1 4 LED blinks green to show that this is switch 1 in the stack 2 Stack member 2 5 LED is solid green to show that switch 2 is a stack member 3 Stack member 3 6 LED is solid green to show that switch 3 is a stack member When you select the Stack LED mode the representative Stack LEDs are green when the Stack Wise ports are up and the representative Stack LEDs are amber when the ports are down PoE LED If the PoE LED mode
28. support this management communication The XPS 2200 communicates with each switch through the 12 pin cable All connected switches can simultaneously communicate with the XPS 2200 You can configure these XPS 2200 features through the switch software e Enable XPS active or standby mode for each connected switch e Configure switch priority for XPS support e List the connected switches and power supply module sizes e Report when a switch is powered by the XPS e Report the XPS power supply module status e Read and monitor backup failure and exception history See the switch software configuration guide on Cisco com http www cisco com en US products ps 10745 products_installation_and_ configuration_guides_list html StackPower Connector Catalyst 3750 X Switches The Catalyst 3750 X switches have a StackPower connector for use with Cisco StackPower cables to configure a switch power stack that includes up to four switches By adding an XPS 2200 expandable power system you can configure a power stack that comprises up to nine switches A switch power stack can be configured in redundant or power sharing mode You can order these StackPower cables from your Cisco sales representative e CAB SPWR 30CM 0 3 meter cable e CAB SPWR 150CM 1 5 meter cable For details about connecting StackPower cables and StackPower guidelines see the Planning a StackPower Stack Catalyst 3750 X Switches section on page 2 8 Management Ports Etherne
29. t Management Port You can connect the switch to a host such as a Windows workstation or a terminal server through the 10 100 Ethernet management port or one of the console ports see Figure 1 5 and Figure 1 6 The 10 100 Ethernet management port connection uses a RJ 45 crossover or straight through cable The RJ 45 console port connection uses the supplied RJ 45 to DB 9 female cable The USB console port uses a USB type A to USB 5 pin mini Type B cable Table 1 19 shows the Ethernet management port LED colors and their meanings Table 1 19 RJ 45 Console Port LED Color Description Green Active link to PC Catalyst 3750 X and 3560 X Switch Hardware Installation Guide P20 OL 19593 01 _ Chapter 1 Product Overview Management Options W Table 1 19 RJ 45 Console Port LED Color Description Off Inactive link Amber POST failure USB Mini Type B Port The switch provides a USB mini Type B console connection on the front panel and the RJ 45 console port on the switch rear panel Console output is always active on both connectors but console input is active on only one connector at a time with the USB connector taking precedence over the RJ 45 connector Use a USB type A to USB 5 pin mini Type B cable to connect a PC or other device to the switch The required USB cable is included in the optional accessory kit part number 800 33434 The connected device must include a terminal emulation application Wi
30. the device manager in the switch memory to manage individual and standalone switches This web browser interface offers quick configuration and monitoring from anywhere in your network For information see the switch getting started guide and the device manager online help OL 19593 01 Catalyst 3750 X and 3560 X Switch Hardware Installation Guide Chapter1 Product Overview W Management Options Cisco IOS CLI You can configure and monitor the switch and switch cluster members from the CLI You can access the CLI by connecting your management station directly to the switch console port or by using Telnet from a remote management station See the switch command reference on Cisco com for more information CiscoWorks application The CiscoWorks LAN Management Solution LMS is a suite of management tools that simplify the configuration administration monitoring and troubleshooting of Cisco networks See the LMS documentation for more information SNMP network management You can manage switches from a Simple Network Management Protocol SNMP compatible management station that is running platforms such as HP OpenView or SunNet Manager The switch supports a comprehensive set of Management Information Base MIB extensions and four Remote Monitoring RMON groups See the switch software configuration guide on Cisco com and the documentation that came with your SNMP application for more information Network Configurations
Download Pdf Manuals
Related Search