Samsung SW-248BEN
Contents
1. Erasing disc types CD RW Disc diameter 120 mm or 80 mm Data transfer rate Recording CD R DRIVE PERFORMANCE 7200 KB sec 6000 KB sec 4800 KB sec 3600 KB sec 2400 KB sec 16X 1800 KB sec 12X 1200 KB sec 8X 600 KB sec 4X 48X 40X 32X 24X N N mN NN ee NA NA NA NA NA Se NA 2400 KB sec 1 1800 KB sec 1 1200 KB sec 6X 2X 8X 600 KB sec 4X Reading CD R CAV 48X CD RW CAV 40X PIO Mode 4 16 6MB sec Multiword DMA mode 2 16 6MB sec UDMA mode 2 33 3MB sec eer Data Buffer Data Buffer Laser ma laser Slide mechanism Stepping motor Spindle motor Brushless motor ee mechanism Tray DC motor Soft Eject Horizontal Vertical ERROR RATE ERRORRATE Mode1 1 block 10712 Mode 2 1 block 10 FRONT PANEL Eject button Auto eject or Auto inject Indicator Play Read GREEN Record RED Operation LED Headphone output Stereo mini jack 3 6 mm 0 65 20 vrms 33 ohm Volume control control Dial type REAR PANEL sond power 5 VDC 1 5 A RMS 12 VDC 1 5 A RMS Interface connector ATAPI BUS E IDE Audio output Line out 0 75V 20 vrms 47Kohm Jumper block Molex 70203 or other compatible models OPERATING Operations Temperature 5 45 C Humidity 10 80 ENVIRONMENT Storage Temperature 25 60 C Humidity 10 90 Dimensions 148 2 W x 42 H x 184 D mm including bezel GENERAL2. and then select Eject to take the CD out Select the drive where the disc is inserted from Windows Explorer Right click the mouse and select Eject to take the CD out When recording NERO or Easy This seems to occur when you select the recording function as the CD Creator system selects Image Recorder instead of SW 248 it will be recorded not on a In this case select a recorder from the menu items at the upper part CD but a form of image file of NERO or Easy CD Creator and then select SW 248 from the Recorder Selection window peca When installing the recording software try not to install the software before the ROM drive as this makes the Image Recorder selected The Recorder cannot Use the firmware automatic upgrade function available at the ODD recognize the disc service website to download the newest firmware and then reinstall the recording software which is included in the bundle Http samsung ODD com www samsungelectronics com odd SAMSUNG DIGITal everyone s invited Specifications ll SAMSUNG continually strives to improve its products Both the design specifications and these user bs instructions are thus subject to change without notice Technical Specifications SW 248B ITEM CD RW DISC Disc types CD DA Audio CD ROM CD ROM XA CD Plus CD Extra supported Photo CD Single Multi session Video CD ready Enhanced CD in read mode CD I FMV CD R CD RW CD TEXT
3. In particular a disc with a crack on the inner tracks may break while in use SAMSUNG DIGITal everyone s invited Safety Precautions Never allow food particles or foreign substances to enter the drive casing To protect against the risk of fire do ot spill such liquids as alcohol and benzene on the drive Do not disassemble attempt to repair or modify the device without express approval as directed in the manual _ Arbitrary removal of the bezel may cause the disc to pop out during operation To reduce the risk of damage electric shock and fire SAMSUNG DIGI lal everyone s invitedm Introduction 1 Headphone Connector Connector for stereo headphones with a 3 6 mm stereo mini jack 2 Headphone volume control This headphone volume control adjusts the volume for your headphones You can only use the headphone jack and volume control when you have installed the required software utilities For example the Microsoft Windows Media player can be used 3 Emergency eject hole if the compartment does not open when you press the Eject button power off the computer insert a pin or unfolded paper clip in the hole and push firmly 4 LED Indicator Light GREEN Read RED Record 5 Eject button 6 Disc compartment the compartment opens and closes automatically when you press the Eject button Design and specifications are subject to change without prior notice SAMSUNG DIGITal
4. Net weight 770g RELIABILITY RELIABILITY MTBF 125 000 POH Duty 20 Design and specifications are subject to change without prior notice
5. ROM drive record speed There are two recording methods e Low speed file by file e High speed transfer of an image file from the hard disk af If the transfer speed of the CD ROM drive is slower than the record speed reduce the record speed SAMSUNG DIGITal everyone s invited Troubleshooting Caution with errors a Caution with errors Every CD R or CD RW drive records data by applying recording laser onto a CD If the CD is damaged or recording data is not possible you need to remove the following causes of the error before using the CD It is recommended to set a CD R or CD RW drive as follows 7 Do not work ona multi tasking environment and remove screen savers u If you work on a multi tasking environment while the CD RW drive is recording deleting data Buffer Under Run may occur Do not allow any external access to the Host PC while recording data u If another user accesses your printer through a network while you are recording data errors may occur J Remove the Auto Run function of the CD If you insert a CD that has the Auto Run function to a drive connected to a PC while recording deleting data this may cause errors How to cancel select the Auto Run function Cancel Select the Auto Run function in Start gt Setting gt Control Panel System gt Device Manager gt CD ROM Setting if Use image files when you record many small files If you use a lot of small size files for recording
6. everyone s invitedm Introduction Digital output terminal You can connect a sound card or MPEG card which support Digital output terminal to your drive using this two pin terminal Sound output terminal You can connect a sound card to your drive using this four pin terminal This function is not covered in detail in this guide Refer to the documentation supplied with your sound card Master slave select terminal Usually this is a pre set configuration as illustrated below Verify that the setting is as illustrated If it is not simply remove the jumper and place it in the correct position Interface terminal This input output interface terminal is used to connect the 40 pin flat cable from the IDE interface to the CD R RW drive Power terminal The power terminal is a four conductor male plug A 5V DC B 12V DC SAMSUNG DIGITal everyone s invitedm Setup Installing the CD R RW Drive To install your CD R RW Drive in the PC proceed as follows T Make sure that the PC is powered off and disconnected from any power source 2 If necessary attach a horizontal bracket to both sides of the drive 3 Remove the cover from a free expansion slot and install the CD R RW drive as shown in the illustration Connecting the Cables Mano SAMSUNG DIGITal everyone s invited Setup T Connecting the power cable The 4 pin power cable f
7. from the following Web site http samsung ODD com http samsung com System Requirements Before you install the CD R RW drive we strongly recommend that you check that your setup meets the system requirements listed below tem Description C rmb ter Intel Pentium II 400MHz or higher 64 MB of RAM or higher with an 80pin IDE pi interface for Ultra DMA Windows 98 2000 ME XP NT4 0 or higher SAMSUNG DIGITal everyone s invited Troubleshooting If you have any problems recording via your CD R RW drive follow the appropriate instructions below for the source that you are using Hard Drive T Check whether the source file is corrupted Optimize the hard disk by using the Windows defragmenter feature START PROGRAMS ACCESSORIES SYSTEM TOOLS DISC DEFRAGMENTER J Decompress the hard disk if it is compressed Make sure that the space available on the hard disk is at least twice the size of the largest file to be recorded on the disc 4 H If you wish to record more than 1000 small files e First create an image file and copy the image file to the disc e Choose the low record speed e Compress small files and then record them Network Drive T Copy the network drive contents to the hard disk and then from the hard disk to the CD R RW drive CD ROM Drive T Clean the source CD if necessary Create an image file and then copy the image file to the CD R RW drive f Check the CD
8. this may reduce the transaction rate of the PC Although Justlink function is often run the recording quality may become low u If you copy a CD from another you do not require making available space in the hard disk However when you use image files you need to copy them on the hard disk first and then copy to a CD In this case you need to ensure maximum 700MB of available space in the hard disk for reliable recording process Use an E IDE cable which has the specified length 46cm w Using E IDE cables longer than 46cm may cause errors during data transaction Use only one recording software program To install a software program for recording uninstall any other types or versions of recording software programs first and then reboot the computer Make sure you use the recording software CD Nero Burning Rom Roxio Easy CD Creator provided by us Using our software program with others may cause errors in recording Term Description T What is Buffer Under Run u Every CD R or CD RW drive records the data that the Host PC wants to record until the data flow ends However if the buffer becomes empty temporarily this may cause errors in recording data Zz What is Auto Run If inserting a CD into a drive the operating system executes the Autorun inf file of the CD automatically J What is Justlink This function is to check the buffer to see if there are data while recording If the buffer is empty i
9. SAMSUNG DIGITal everyone s invited Index I Main Page d Safety Precautions Notational Installation While Operating Other Introduction Front Rear Setup Installing the CD R RW Drive Connecting the Cables Installing the CD Record Utility Installing the Device Driver Setting Up the Device Driver _Using the Drive Using the CD R RW Drive Storing and Cleaning Your Discs Upgrading the Firmware Flash Memory System Requirements Troubleshooting Solving Recording Problems Caution with errors Solving Technical Problems I Specifications SAMSUNG DIGITal everyone s invited Safety Precautions Notational Tr dosing wn base precmuleed lo anaut user balety and reece iha rak af properly datage Fiats read thi carefully and follow the piachtena al all litre for Propet ue ol tha dirce Warning Caution Warning This symbol indicates explanations about extremely dangerous matters If users ignore this symbol and handle the device the wrong way serious injury or death could result Caution This symbol indicates explanations about dangerous matters If users ignore this symbol and handle the device the wrong way damage to home or property could result Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment Prohibited Important to read and understand at all times Do not disassemble Any change or modification
10. e jumper is connected to CS CSEL you can control the device by using the host interface signal CSEL In general connection to MA is recommended f Connecting the audio cable from a sound card Connect the 4 pin audio cable between the sound output terminal on the CD R RW drive and the audio input terminal on the sound card For clearer sound use a digital output terminal Available only for the CAID that supports digital output This may not be available for general sound cards SAMSUNG DIGITal everyone s invited Setup Installing the CD Record Utility To record data on a CD R or CD RW disc in the CD R RW drive you must first install the CD record utility For compatibility reasons you are recommended to uninstall any existing software of the same type before installing this utility 7 Insert the disc supplied with the CD R RW drive in the drive Follow the instructions displayed on the screen to install the utility Refer to the separate utility documentation for further details J Store the utility disc in a safe place Installing the Device Driver No additional device driver is needed for Windows 98 2000 ME XP NT4 0 as the default Windows device driver is used You can check that the CD R RW drive has been correctly detected by Windows To do so proceed as follows T Double click on the My Computer icon on your desktop E Double click on the Control Panel folder 3 Double click on the System
11. gt System gt Device Manager gt IDEATA ATAPI Controller gt Default Assistant IDE Channel Advanced Information SAMSUNG DIGITal everyone s invited Troubleshooting Problem Meaning Solution The CD R RW drive is not Check that the power audio and IDE cables are correctly connected detected by the computer to the computer After installing the CD R RW Change the IDE cable and reconnect it to the computer drive the PC gets slower Preferably connect a second IDE cable to the CD R RW drive in master mode Check the position of the jumper in the master slave select terminal The CD R RW drive is not Reinstall the device driver or update it with the latest version by recognized by MS DOS downloading it from the Samsung Web site Http samsung ODD com Http samsung com The CD R RW drive is not This case may occur when there is a Windows installation problem detected by Windows reinstall Windows SEEN No sound is heard from an Check whether the audio cable is correctly connected to the sound audio CD output terminal on the CD R RW drive and the sound card CD IN terminal Check that the sound card is operational E n Adjust the volume control Run the CD player supplied with Windows or your sound card You can listen to the CD by connecting headphones to the appropriate connector If you have installed the appropriate player such as Microsoft Windows Media Player you can adj
12. icon f Click on the Device Manager tab 5 Expand the CD ROM branch g The SAMSUNG CD R RW SW device name is displayed The SAMSUNG device driver enables discs in the CD R RW drive to be read but not recorded in an MS DOS environment the driver is located in the D driver folder on the CD record utility disc Setting Up the Device Driver Automatic Setup The device driver is located in the Ddriver folder of the CD Record Utility disc which is provided in the package 7 Insert the CD Record Utility disc into the CD ROM drive and open the Ddriver folder a Run the CDSETUP EXE file in the Ddriver folder J When Setup is successfully completed click OK button or press the Enter key Reboot the computer Manual Setup T Make the C SAMSUNG directory Copy the files from the diskette to the C SAMSUNG directory To do so type COPY D Ddriver C SAMSUNG after the C prompt and press Enter J Edit the CONFIG SYS file Add the DEVICE C SAMSUNG SSCDROM SYS D SSCDO000 V entry AST DEVE E VER Ba ee eS Va LE Y f Edit the AUTOEXEC BAT file Add the C SAMSUNG MSCDEX D SSCD000 entry PAE ee D Reboot the computer SAMSUNG DIGITal everyone s invitedm Using the Drive Using the CD R RW Drive To play audio or video CDs in your CD R RW drive proceed as follows 4 Push the power button and boot the computer 2 After booting the computer open the disc compar
13. not expressly approved by designated qualified personnel could void your authority to operate this device Always make sure that the disc does not have a crack before use If the disc has a crack especially around the center hole it is recommended to make a copy immediately and use the copy instead When a cracked disc is used continuously the size of the crack is likely to grow and this will eventually result in irreparable damage to the disc Important to read and understand at all times SAMSUNG DIGITal everyone s invited Safety Precautions Installation Place the drive on a level surface Failure to do so may cause the device to fall onto a hard surface resulting in damage or malfunction Do not place the drive in direct sunlight Avoid low or high temperature environments Avoid high humidity environments SAMSUNG DIGITal everyone s invited Safety Precautions While Operating Handle with caution to prevent damage from external shock Do not drop the drive and protect it fromsevere shocks It can damage the drive or cause it to malfunction Do not move the drive while in operation and do not attempt to open the disc tray byforce Make sure to close all working programs before attempting to open the tray and always usethe open close button Do not insert a pin into the emergency opening while in operation Do not use cracked distorted or damaged discs
14. rom the internal power unit of your computer must be connected to the power terminal on the rear of the CD R RW drive Ground A Cut Side Ground 12V DC Note An improperly connected power cable may cause trouble Check the direction of the power connector and the incline side of the CD R RW drive before connecting 2 Connecting the E IDE cable Insert the IDE cable 40 pin which is connected to the hard disk to the interface terminal Place the red line of the cable close to the Pin 1 a When using one E IDE cable Connect the cable to the SL Slave of the Master Slave Select Terminal at the rear of the CD R RW drive Slave Drive Choose the SL Jumper Hard Drive MainBoard a When using two E IDE cable If there is only one CD R RW drive select MA Master Master Drive Choose the MA Jumper Ib Hard Drive a e MainBoard af Primary 1 e R Secondly 1 SAMSUNG DIGITal everyone s invited Setup If there is two CD R RW drive select MA Master SL Slave a Master Drive Choose the MA Jumper b Slave Drive Choose the SL Jumper e Hard Drive d MainBoard e Primary f Secondly 1 3 Installing a jumper on the master slave select terminal Connect a jumper to the rear side of the CD R RW If the jumper is connected to MA Master it will work in the Master mode If the jumper is connected to SL Slave it will work in the Slave mode If th
15. t waits at the address and then restarts recording after the buffer is full You can avoid Buffer Under Run problems by applying the above mentioned principle SAMSUNG DIGITal everyone s invited Troubleshooting Recommended Disc Types CD R RITEK TAIYO YUDEN MCC ACER SKC BEALL MPO CMC PRODISK MAXELL FUJI MCI POSTECH TDK GIGA PLASMON CD RW CD RW RICOH RITEK MCC PRODISK SKC CMC ACER 1X 4X H S RW RICOH CMC RITEK ACER PRODISK SKC 10X 12X 16X General DMA Installation Guide Windows 98 Me Important Please read the entire DMA installation guide before installing your CD R RW drive About DMA Installation For stable writing performance at high speeds Installation of DMA transfer mode for E IDE ATAPI interface is strongly recommended We recommend DMA mode for fast writing DMA Setting Before you install your CD R RW drive we recommend to set DMA to enabled on your PC system See the following procedure to set DMA transfer mode in windows oprerating system Windows 98 ME Click on START Select your CD R RW drive Click on Settings Click on the Properties button Select Control Panel Click on the Settings tab Select the System Icon Check the DMA checkbox to enables DMA Select the Device Manager panel Click OK in System Properties Restart your PC Expand the CD ROM icon Windows 2000 XP Select the DMA mode by selecting Start gt Setting gt Control Panel
16. tment by pressing the Eject button Insert the disc CD with the label on the disc facing upwards and close the disc compartment by pressing the Eject button The indicator light comes on 4 Play the disc CD Playing Audio CDs Run the CD player supplied with Windows or your sound card You can listen to the CD by connecting headphones to the appropriate connector If you have installed the appropriate player such as Microsoft Windows Media Player you can adjust the volume using the headphone volume control on the drive front panel If you select digital playback in all versions of Windows Media Player sounds cannot be output to the headphone jack of the product Storing and Cleaning Your Discs To ensure a long service life for your discs and drive follow the pre cautions below when storing and cleaning your discs Do not place a disc in direct sunlight Store a disc vertically in a well ventilated and stable location to Bo a Do not write or attach a label on a disc i Do not drop a disc or place heavy objects on it Do not touch the surface of a disc hold it by the edges To clean a disc polish lightly from the inside of the disc to the outside with a soft cotton cloth Do not leave the disc compartment open when you are not using it SAMSUNG DIGITal everyone s invited Using the Drive Upgrading the Firmware Flash Memory The product firmware can be upgraded by downloading the updated file
17. ust the volume using the headphone volume control on the drive front panel If you select DIGITAL at CD Audio Play in Media Player of Windows ME XP the earphone does not appear in the Digital Mode Check whether the CD is of good quality and clean it if necessary A CD is not read or is read too slowly The disc compartment will Check that the power cable is correctly connected not open Power off and disconnect the PC Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens When the MPEG software Adjust the size of the replay screen plays a Video CD the pictures are not regular and the running l speed is too slow After checking the display resolution adjust it if necessary ee The Disc is not in message is The computer may not recognize the disc if you start playback too displayed even though a disc quickly after inserting the disc Open and close the disc has been inserted compartment and try again e Clean the disc and try again The CD R RW drive is not The interface mode of the sound card is AT BUS detected after it is connected to You must therefore connect the CD R RW drive to the IDE port on a sound card the PC mother board rather than to the sound card or install an E IDE compatible sound card IN CD has the Formatted Right click the mouse on TRAY ICON right side of the menu bar at Disc Eject function the bottom of the monitor
Download Pdf Manuals
Related Search