Cisco 1-Port 10GE, C-Band Tunable, WDM-PHY Shared Port Adapter
Contents
1. C band unit full tunable from 1529 55 to 1561 84 Spectral Range lambdaTmin to lambdaTmax 1530 to 1561 nm Spectral Width at 20 dB lambda delta20 25 GHz Optical Transmitter Type Lithium Niobate external modulator Output Power PTmin to PTmax 3 dBm 6 dBm Required Optical Return Loss Minimum ORLmin 27 dB Extinction Ratio Minimum reminx gt 10 5 dB Laser Safety Class 1 Optical Receiver Type Avalanche photo diode APD Chromatic Dispersion Tolerance DLRmax Up to 1200 ps nm 2 dB penalty Minimum BER BERmin FEC Off 10E 12 FEC On 10E 15 EFEC On 10E 15 Reflectance Between Far End Tx and Near End Rx Maximum 27 dB Receiver Reflectance Maximum 14 dB Input Wavelength Bandwidth lambdac_rx 1290 nm to 1605 nm Connector Type Tx Rx LC duplex shuttered Table 4 shows optical performance with OSNR given in 0 5 nm Res BW Table 4 Optical Performance OSNR FEC Type Pre FEC BER Post FEC BER Input Power Sensitivity CD Tolerance 23 dB OFF lt 10E 12 8 to 20 dBm C band 1200 ps nm 19 dB OFF lt 10E 12 8 to 20 dBm C band 1000 ps nm 19 dB OFF lt 10E 12 8 to 22 dBm C band om 10 dB GFEC lt 10E 5 lt 10E 15 8 to 18 dBm 800 ps nm 8 5 dB GFEC lt 10E 5 lt 10E 15 8 to 18 dBm 19 dB EFEC lt 7x10E 4 lt 10E 15 8 to 26 dBm 800 ps nm 192. 7 Data Sheet EE Feature Description Alarms and Performance Alarm reporting Monitoring Loss of signal LOF Loss of OTN frame LOF e Loss of OTN multiframe LOM e OTU alarm indication signal OTU AIS e OTU backward defect indication OTU BDI e ODU alarm indication signal ODU AIS e ODU open connection indication ODU OCl ODU locked ODU LCk e ODU backward defect indication ODU BDI e ODU payload type identifier mismatch ODU PTIM OTU signal fail OTU_SF_BER e OTU signal degrade OTU_SD_BER OTU_SF_BER and OTU_SD_BER alarms are based on monitoring OTU BIP errors with a user settable threshold crossing Error counts OTU BIP OTU BEI ODU BIP and ODU BEI Threshold crossing alerts TCAs for OTU BIP errors SM TCA and ODU BIP errors PM TCA with user settable threshold FEC Features No FEC ability to turn off error correction for use with non FEC supporting interfaces for example Xenpak XFP GFEC standard G 975 Reed Soloman algorithm EFEC standard G 975 1 two orthogonally concatenated BCH super FEC code This FEC scheme contains three parameterizations of the same scheme of two orthogonally interleaved block codes BCH The constructed code is decoded iteratively to achieve the expected performance FEC statistics for pre FEC BER corrected errors EC and uncorrected words UC Optical Features Line rate 10 3125 Gbps 100 ppm or 11 0957 Gbps 100 ppm Duplex LC shutter
3. Afafe CISCO Data Sheet Cisco 1 Port 10 Gigabit Ethernet 10GE Tunable WDM PHY Shared Port Adapter The Cisco I Flex design combines shared port adapters SPAs and SPA interface processors SIPs using an extensible design that enables service prioritization for voice video and data services Enterprise and service provider customers can use the improved slot economics resulting from modular port adapters that are interchangeable across Cisco routing platforms The l Flex design maximizes connectivity options and offers superior service intelligence through programmable interface processors which deliver line rate performance l Flex enhances speed to service revenue and provides a rich set of quality of service QoS features for premium service delivery while effectively reducing the overall cost of ownership This data sheet contains the specifications for the Cisco 1 Port 10GE Tunable WDM PHY Interface SPA Product Overview The Cisco 1 Port 10GE Tunable WDM PHY SPA provides a tunable optical interface that can be used to connect directly to dense wavelength division multiplexing DWDM transport systems eliminating the need for an optical transponder The Tunable WDM PHY SPA provides full 80 channel tunability with 50 GHz spacing across the C band and meets ITU specifications It supports G 709 framing for robust connectivity and SONET like operations administration maintenance and provisioning OAM amp P as well as generic forwa
4. All contents are Copyright 1992 2007 Cisco Systems Inc All rights reserved This document is Cisco Public Information Page 6 of 7 Data Sheet Americas Headquarters Asia Pacific Headquarters Europe Headquarters Cisco Systems Inc Cisco Systems Inc Cisco Systems International BY 170 West Tasman Drive 168 Robinson Road Haarlerbergpark a e 1 a San Jose CA 95134 4706 28 01 Capital Tower Haarlerbergweg 13 49 USA Singapore 068912 1101 CH Amsterdam C l 5 C O WWWCISCOCOM wwweisco com The Netherlands Tel 408 526 4000 Tel 65 6317 7777 www europe cisco com 800 553 NETS 6387 Fax 65 6317 7799 Tel 31 0 800 020 0791 Fax 408 527 0883 Fax 310 20 357 1100 Cisco has more than 200 offices worldwide Addresses phone numbers and fax numbers are listed on the Cisco Website at www cisco com go offices 2007 Cisco Systems Inc All rights reserved CCVP the Cisco logo and the Cisco Square Bridge logo are trademarks of Cisco Systems Inc Changing the Way We Work Live Play and Learn is a service mark of Cisco Systerns Inc and Access Registrar Aironet BPX Catalyst CCDA CCDP CCIE CCIP CCNA CCNP CCSP Cisco the Cisco Certified Internetwork Expert logo Cisco IOS Cisco Press Cisco Systems Cisco Systems Capital the Cisco Systems logo Cisco Unity Enterprise Solver EtherChannel EtherFast EtharSwitch Fast Step Follow Me Browsing FormShere GigaDrive GigaStack Home Link Internet Quotient IOS iPhones IP TV iO Ex
5. ROADMs allowing customer traffic to be carried separately and securely on a single DWDM wavelength It eliminates the need for bulky and expensive optical transponders It simplifies network operation by allowing DWDM optical functions and wavelengths to be managed as part of the IP network reducing the number of network elements and simplifying network management Combined with the Cisco ONS 15454 Multiservice Transport Platform MSTP the 1 Port 10 Gigabit Ethernet Tunable WDM PHY SPA provides a powerful solution for bringing IP intelligence to metropolitan and core optical transport networks Metro regional DWDM and long haul applications are both possible with this product Long haul applications of up to 2000 km are supported with the use of the built in EFEC support Features and Benefits The 1 Port 10GE Tunable WDM PHY SPA is a primary element in the Cisco IP over DWDM solution integrating an OTN compliant Optical Transport Network and ITU compliant interface directly onto the router Furthermore as a SPA the customer also gains all the benefits of Cisco l Flex modularity improved slot economics interface interchangeability across platforms and investment protection Table 1 summarizes the features and benefits of this product Table 1 Features and Benefits Feature Benefit Hardware 80 Channel Tunability Superior wavelength tunability across C band e Superior provisioning flexibility and scalability e ITU compl
6. and Safety GR 63 CORE NEBS Physical Protection Ordering Information To place an order contact your local Cisco representative or visit the Ordering page on the Cisco website Use the ordering information provided in Table 6 To download software visit the Cisco Software Center Table 6 Ordering Information Product Name Part Number Cisco 1 Port 10GE C Band Tunable WDM PHY Shared Port Adapter for LAN PHY Applications SPA 1X10GE L ITUC Service and Support Cisco offers a wide range of services programs to accelerate customer success These innovative services programs are delivered through a unique combination of people processes tools and partners resulting in high levels of customer satisfaction Cisco services help you protect your network investment optimize network operations and prepare your network for new applications to extend network intelligence and the power of your business For more information about Cisco Services refer to Cisco Technical Support Services or Cisco Advanced Services For More Information For more information about the Cisco SPA SIP portfolio visit www cisco com go spa For details about the Cisco IP over WDM solution visit www cisco com go crs Alternatively you may contact your local Cisco account representative For the most up to date compliance and approvals information see Regulatory Compliance and Safety Information at www cisco com
7. dB EFEC lt 7x10E 4 lt 10E 15 8 to 27 dBm 7 dB EFEC lt 7x10E 4 lt 10E 15 8 to 20 dBm 800 ps nm 5 dB EFEC lt 7x10E 4 lt 10E 15 8 to 20 dBm This is not a specification Chromatic Dispersion Tolerance is listed as an indication of the maximum chromatic dispersion that the interface can tolerate only in the specified case quoted in Table 4 with 23 dB of OSNR All contents are Copyright 1992 2007 Cisco Systems Inc All rights reserved This document is Cisco Public Information Page 5 of 7 Data Sheet a Approvals and Compliance The Cisco 1 Port 10GE Tunable WDM PHY SPA is tested and conforms to the international compliance specifications listed in Table 5 Table 5 Compliance and Agency Approvals Feature Description Safety Standards UL CSA IEC EN 60950 1 IEC EN 60825 Laser Safety AS NZS 60950 FDA Code of Federal Regulations Laser Safety EMI FCC Class A ICES 003 Class A AS NZS CISPR 22 Class A CISPR 22 EN55022 Class A VCCI Class A ETSI and EN EN300 386 Telecommunications Network Equipment EMC EN55022 Information Technology Equipment Emissions EN55024 Information Technology Equipment Immunity EN50082 1 EN 61000 6 1 Generic Immunity Standard Network Equipment Building Standards This product is designed to meet the following requirements qualification in NEBS progress SR 3580 NEBS Criteria Levels Level 3 GR 1089 CORE NEBS EMC
8. ed faceplate optical connector Full C band tunable laser with 50 GHz spacing Optical power monitoring laser output power 1 5dB receiver signal average power 1 5dB Reliability and Availability Online insertion and removal OIR without affecting system traffic Single SPA software reset Network Management Cisco IOS Software command line interface CLI Simple Network Management Protocol SNMP CraftWorks Interface CWI Physical Dimensions Double height double width SPA Occupies four standard single height SPA slots or two double height SPA slots Weight 2 75 Ibs 1 25 kg Height 1 6 in 4 06 cm Double height form factor Depth 7 28 in 18 49 cm Width 13 53 in 84 36 cm Double wide form factor Power 46W Environmental Conditions Storage temperature 40 to 70 40 to 15F Operating temperature 5 to 40 41 to 104F Operating humidity 5 to 85 RH Storage humidity 5 to 95 RH All contents are Copyright 1992 2007 Cisco Systems Inc All rights reserved This document is Cisco Public Information Page 4 of 7 Data Sheet a DWDM Line and Optical Specifications Table 3 shows the detailed DWDM optical and line specifications for the optical interface Table 3 Additional Specifications DWDM Line Interface Specification DWDM Line Interface DWDM Line Interface Bit Rate 10 3125 100 ppm 11 0957 100 ppm Nominal Wavelengths lambdaTnom
9. iant EFEC Support Superior reach up to 2000 km without regeneration G 709 OTN Support e SONET like management administration and performance monitoring All contents are Copyright 1992 2007 Cisco Systems Inc All rights reserved This document is Cisco Public Information Page 2 of 7 Data Sheet a Feature Benefit IP over DWDM Solution Transponder Integration e No need for external transponder shelves Less network elements to manage enhanced reliability Reduced operating expenses as well as capital expenditures by reducing space power and the cost of the transponder and associated shelves and common card Management Integration e Single IP over DWDM design tool for network planning e SONET SDH like OAM amp P for performance monitoring e Open architecture for third party interoperability Interoperability e Fully interoperable with Cisco 15454 MSTP e Designed to be interoperable with third party DWDM equipment Product Specifications Detailed product specifications are listed in Table 2 Table 2 Product Specifications Feature Description Product Compatibility Cisco 12000 Series Routers Port Density 1 x 10 Gigabit Ethernet Ethernet Features Encapsulations ARPA IEEE 802 2 SAP IEEE 802 3 SNAP IEEE 802 3x flow control 802 1q VLAN support jumbo frames 9188 bytes 802 1ad QinQ support IEEE 802 1p tagging Bridge protocol data unit BPDU C
10. isco Discovery Protocol and VLAN Trunking Protocol VTP filtering Layer 2 Protocol BPDU Cisco Discovery Protocol and VTP tunneling Layer 2 access list MAC address based filtering Up to 8000 VLANs per SPA and subject to a limit of 4000 VLANs per port for 802 1q Up to 5000 MAC accounting entries per SPA source MAC accounting on the ingress and destination MAC accounting on the egress Up to 2000 MAC address entries for destination MAC address filtering per SPA and up to 1000 MAC address filtering entries per port Per port byte and packet counters for policy drops oversubscription drops cyclic redundancy check CRC error drops packet sizes and unicast multicast and broadcast packets Per VLAN byte and packet counters for policy drops oversubscription drops and unicast multicast and broadcast packets Per port byte counters for good bytes and dropped bytes Protocol Support OTN G 709 compliant selectable OTN disabled no OTN G 709 framing line rate of 10 3125 Gbps OTN enabled OTN G 709 framing line rate of 11 0975 Gbps Mapping of IEEE 802 3ae 10GBASE R signal into an overclocked OTU2 running at 11 0975 Gbps Local internal and line network loopback Local internal or loop recovered from network timing 100 ppm local clock accuracy over operating temperature All contents are Copyright 1992 2007 Cisco Systems Inc All rights reserved This document is Cisco Public Information Page 3 of
11. pertise the iQ logo IO Net Readiness Scorecard iQuick Study LightStream Linksys MeetingPlace MGX Networking Academy Network Registrar Packet PIX ProConnect RateMUX ScriptShare SlideCast SMARTnet StackWise The Fastest Way to Increase Your Internet Quotient and TransPath are registered trademarks of Cisco Systems Inc and or its affiliates In the United States and certain other countries All other trademarks mentioned in this document or Website are the property of their respective owners The use of the word partner does not imply a partnership relationship between Cisco and any other company 0701R Printed in USA C78 395292 00 02 07 All contents are Copyright 1992 2007 Cisco Systems Inc All rights reserved This document is Cisco Public Information Page 7 of 7
12. rd error correction GFEC for regional applications For long haul application support the high gain enhanced forward error correction EFEC functionality is provided which can extend optical reach up to 2000 km without optical electrical regeneration The 10GE Tunable WDM PHY SPA is part of the Cisco IP over DWDM solution portfolio Service providers benefit from IP over DWDM integration through faster service provisioning increased reliability and simplified network management Integrated DWDM transponders simplify the network by reducing the number of network elements and also scale at a lower total cost to reduce bandwidth cost Finally P over DWDM solutions allow service providers to more cost effectively use the rich QoS and IP intelligence of Cisco routers in their transport networks Figure 1 Cisco 1 Port 10GE Tunable WDM PHY Interface SPA All contents are Copyright 1992 2007 Cisco Systems Inc All rights reserved This document is Cisco Public Information Page 1 of 7 Data Sheet Applications Figure 2 shows Tunable WDM PHY SPA applications Figure 2 Tunable WDM PHY SPA Applications Company ONS 15454 ONS 15454 Company ROADM ROADM B Metro DWDM Access Ring Lambda 3 FN AS Lambda 4 oe ia ONS 15454 ONS 15454 ROADM ROADM The 1 Port 10GE Tunable WDM PHY SPA allows the router to connect directly to an optical ring using either a passive DWDM line system or reconfigurable optical add drop multiplexers
Download Pdf Manuals
Related Search