Cisco ATM Cable DS-3 & E3, 3m
Contents
1. PA MC T3 Port Adapter Installation and Configuration OL 2695 05 Chapter1 Overview Port Adapter Slot Locations on the Supported Platforms i Catalyst 6000 Family FlexWAN Module Slot Numbering The Catalyst 6000 family FlexWAN module can be installed in any slot in a Catalyst 6000 family switch except slot 1 which is reserved for the supervisor engine A port adapter can be installed into either port adapter bay 0 or bay 1 on a FlexWAN module Figure 1 8 shows a Catalyst 6000 family switch with two blank port adapters installed in a FlexWAN module amp Note Slot 1 is reserved for the supervisor engine If a redundant supervisor engine is used it would go in slot 2 otherwise slot 2 can be used for other modules Figure 1 8 Catalyst 6000 Family Switch with Port Adapters Installed on FlexWAN Module PA MC T3 Port Adapter Installation and Configuration OL 2695 05 Chapter1 Overview HI Port Adapter Slot Locations on the Supported Platforms Cisco 7200 Series Routers and Cisco 7200 VXR Routers Slot Numbering Cisco 7202 routers have two port adapter slots The slots are numbered from left to right You can place a port adapter in either of the slots slot 1 or slot 2 The Cisco 7202 router is not shown Cisco 7204 routers and Cisco 7204VXR routers have four slots for port adapters and one slot for an input output I O controller The slots are numbered from the lower left to the upper right beginni2. onarren i Overview This chapter describes the PA MC T3 port adapter and contains the following sections Port Adapter Overview page 1 1 Multichannel T3 Overview page 1 2 Features page 1 3 Interface Specifications page 1 3 LEDs page 1 4 Cables Connectors and Pinouts page 1 5 Port Adapter Slot Locations on the Supported Platforms page 1 7 Identifying Interface Addresses page 1 17 Port Adapter Overview The PA MC T3 is a single width single port port adapter that provides one T3 interface connection using BNC connectors See Figure 1 1 The interface can provide up to 28 T1 lines a single T3 group Each T1 line is presented to the system as a serial interface that can be configured individually Figure 1 1 PA MC T3 Faceplate View I OL 2695 05 PA MC T3 Port Adapter Installation and Configuration jg Chapter1 Overview Hs Multichannel T3 Overview Multichannel T3 Overview amp The PA MC T3 T3 link is channelized into 28 independent T1 data lines Each T1 line can be unchannelized or channelized for serial transmission of data Each of the T1 lines can use the whole T1 bandwidth a portion of the T1 bandwidth or the T1 bandwidth in channelized form for data transmission Usable bandwidths for each T1 line are n x 56 kbps or n x 64 kbps where n is a number representing time slots 1 to 24 Channelized T1 allows up to 24 time slots 56 kbps 64 kbps per T1 line The unused portion of the T1
3. page 1 21 Cisco 7304 PCI Port Adapter Carrier Card Interface Addresses page 1 22 Cisco 7401ASR Router Interface Addresses page 1 22 Cisco 7000 Series Routers and Cisco 7500 Series Routers VIP Interface Addresses page 1 22 Table 1 3 summarizes the interface address formats for the supported platforms Table 1 3 Identifying Interface Addresses Platform Interface Address Format Numbers Syntax Catalyst RSM VIP in Port adapter slot number interface port number Port adapter slot 0 or 1 0 0 1 0 Catalyst 5000 family t1 line number channel group number Interface port O switches T1 line number 1 through 28 Logical channel group on the T1 line 0 through 23 Catalyst 6000 family Module slot number port adapter bay number Module slot 2 through 13 3 0 0 1 0 FlexWAN module in interface port number t1 line number channel depends on the number of slots Catalyst 6000 family group number in the switch switches Port adapter bay O or 1 Interface port 0 T1 line number 1 though 28 Logical channel group on the T1 line 0 through 23 Cisco 7200 series Port adapter slot number interface port number Port adapter slot 1 through 6 1 0 1 0 routers and Cisco 7200 t1 line number channel group number depends on the number of slots VXR routers in the router Interface port 0 T1 line number 1 through 28 Logical channel group on the T1 line O through 23 Cisco 7201 router Port adapter slot number interface port nu
4. 0 is always reserved for the I O controller if present PA MC T3 Port Adapter Installation and Configuration OL 2695 05 EZE Chapter1 Overview HI Port Adapter Slot Locations on the Supported Platforms Figure 1 11 shows the slot numbering of port adapters on a Cisco uBR7246 router or Cisco uBR7246VXR router Figure 1 11 Port Adapter Slots in the Cisco uBR7246 and Cisco uBR7246VXR Routers 1 12 shows a PA MC T3 installed in port adapter slot 2 of a Cisco uBR7246 router Figure 1 12 Cisco uBR7246 With a PA MC T3 PA MC T3 Port Adapter Installation and Configuration i12 E OL 2695 05 Chapter1 Overview Port Adapter Slot Locations on the Supported Platforms i Cisco 7201 Router Slot Numbering Figure 1 13 shows the front view of a Cisco 7201 router with a port adapter installed There is only one port adapter slot slot 1 in a Cisco 7201 router Figure 1 13 Port Adapter Slot in the Cisco 7201 Router Cisco 7301 Router Slot Numbering Figure 1 14 shows the front view of a Cisco 7301 router with a port adapter installed There is only one port adapter slot slot 1 in a Cisco 7301 router Figure 1 14 Port Adapter Slot in the Cisco 7301 Router PA MC T3 Port Adapter Installation and Configuration OL 2695 05 EZEN Chapter1 Overview HI Port Adapter Slot Locations on the Supported Platforms Cisco 7304 PCI Port Adapter Carrier Card Slot Numbering The Cisco 7304 PCI port adapter carrier card ins
5. signal DSX 3 able to drive 450 feet 135 meters of 75 ohm coaxial cable 728A or equivalent and meet pulse shape template at the line side OL 2695 05 PA MC T3 Port Adapter Installation and Configuration gy Chapter1 Overview E LEDs LEDs The PA MC T3 has one row of six status LEDs and one ENABLED LED See Figure 1 2 Figure 1 2 PA MC T3 LEDs Table 1 2 lists port LED colors and indications Table 1 2 PA MC T3 LEDs LED Label Color State Meaning ENABLED Green On Port adapter is enabled for operation ALARM Yellow On An alarm condition is received on any configured T1 line or the T3 link Blinking A port adapter boot failure has occurred LOOP Yellow On A T1 line or the T3 link is in a loopback state and is not enabled for normal data traffic LOS Yellow On A loss of the received signal on the T3 link is detected by the line interface unit LIU on the port adapter OOF Yellow On A DS3 out of frame condition AIS Yellow On An alarm indication signal is received on the T3 link FERF Yellow On A far end receive failure signal is detected by the receiver 1 Alarms include T1 loss of frame LOF T1 alarm indication signal AIS T1 yellow alarm indication T3 loss of signal LOS T3 AIS and a T3 far end receive failure FERF yellow alarm 2 This LED blinks momentarily during port adapter initialization 3 When the OOF LED is on the FERF LED is latc
6. you move a VIP or FlexWAN module to a different slot the interface processor or module slot number changes to reflect the new interface processor or module slot Note amp The Cisco IOS software recognizes a configured logical channel group as a serial interface therefore you can use all configuration commands that are available for serial interfaces with configured logical channel groups You can configure a logical channel group to carry data traffic using the following encapsulation methods PPP HDLC SMDS and Frame Relay Set the encapsulation method you want using the serial interface configuration commands For configured logical channel groups you can use all command switches that apply to a serial interface including optimum switching Note Interface ports are numbered from left to right starting with 0 OL 2695 05 PA MC T3 Port Adapter Installation and Configuration gy Chapter1 Overview HZ Identifying Interface Addresses The following subsections describe the interface address formats for the supported platforms Catalyst RSM VIP2 Interface Addresses in the Catalyst 5000 Family Switches page 1 20 Catalyst 6000 Family FlexWAN Module Interface Addresses page 1 20 Cisco 7200 Series Routers and Cisco 7200 VXR Routers Interface Addresses page 1 21 Cisco uBR7200 Series Routers Interface Addresses page 1 21 Cisco 7201 Router Interface Addresses page 1 21 Cisco 7301 Router Interface Addresses
7. adapter slot 0 or 1 on the VIP The bays are numbered from left to right on the VIP 1 18 shows the slot numbering on a VIP2 Figure 1 18 VIP2 Slot Locations PA MC T3 Port Adapter Installation and Configuration OL 2695 05 Bits Chapter1 Overview HI Port Adapter Slot Locations on the Supported Platforms Figure 1 19 shows the slot numbering on a VIP4 Figure 1 19 VIP4 Slot Locations re 1 20 shows two PA MC T3 port adapters in slot 0 and slot 1 of a VIP2 40 Figure 1 20 Two PA MC T3s in Port Adapter Slot 0 and Slot 1 of a VIP2 40 PA MC T3 Port Adapter Installation and Configuration ua OL 2695 05 _ Chapter 1 Overview Identifying amp Identifying Interface Addresses W Cisco 7010 routers have three slots for port adapters and two slots for Route Switch Processors RSPs The slots are numbered from bottom to top You can place the port adapter in any of the VIP interface slots slot 0 through 2 Slots 3 and 4 are always reserved for RSPs The Cisco 7010 router is not shown Cisco 7505 routers have four slots for port adapters and one slot for an RSP The slots are numbered from bottom to top You can place the port adapter in any of the VIP interface slots slot 0 through 3 One slot is always reserved for the RSP The Cisco 7505 router is not shown Cisco 7507 routers have five slots for port adapters and two slots for RSPs The slots are numbered from left to right You can place the
8. bandwidth when not running at full T 1 speeds cannot be used and is filled with idle channel data Aggregation of multiple T1 lines is not supported The PA MC T3 can support a maximum of 128 logical channels Note Note amp Note T1 lines on the PA MC T3 are numbered 1 to 28 instead of the more traditional zero based scheme 0 to 27 used with other Cisco products This is to ensure consistency with telco numbering schemes for T1 lines within channelized multi channel T3 equipment The T3 section of the PA MC T3 supports the maintenance data link channel when using c bit parity as well as payload and network loopbacks The T1 section of the PA MC T3 supports facilities data link FDL in Extended Superframe ESF framing as well as various loopbacks Bit error rate BER testing is supported on each of the T1 lines Testing is typically done over an unframed T1 signal The PA MC T3 supports Cisco High Level Data Link Control HDLC Frame Relay PPP and SMDS Data Exchange Interface DXI encapsulations over each T1 link For Switched Multimegabit Data Service SMDS only DXI is sent on the T1 line so it needs to connect to an SMDS switch that has direct DXI input The PA MC T3 does not support the aggregation of multiple T1 lines called inverse multiplexing or bonding for higher bandwidth data rates The physical T3 link on the PA MC T3 consists of two female BNC connectors one for receive RX and one for t
9. ctor and cable for transmit TX and one for receive RX The BNC connectors are transformer coupled to the PA MC T3 line interface unit LIU which is the analog physical interface on the PA MC T3 The pinout and signal descriptions for the BNC connectors on the PA MC T3 are as follows e Transmit TX Transmitted signals appear on the center contact and the outer shield is ground for the 75 ohm RG 59 coaxial cable you attach to the TX BNC connector e Receive RX Received signals appear on the center contact and the outer shield is ground for the 75 ohm RG 59 coaxial cable you attach to the RX BNC connector A Caution To prevent problems you must check your 75 ohm RG 59 coaxial cable specifications when long cable lengths are required to connect the PA MC T3 to your external DS3 T3 equipment You must install a ferrite sleeve also called a common mode choke on each 75 ohm coaxial cable to reduce the effects of electromagnetic interference EMI Cisco Systems supplies two ferrite sleeves with your PA MC T3 one for each of the two 75 ohm coaxial cables amp Note You must attach the ferrite sleeve on the end of each coaxial cable nearest the PA MC T3 as close to the BNC connector as possible See Figure 1 3 A Caution The ferrite sleeve prevents electromagnetic interference EMI from affecting the T3 equipped system and is a required component for proper system operation PA MC T3 Port Adap
10. dress of the PA MC T3 is 3 1 0 1 0 interface processor slot 3 port adapter slot 1 interface port 0 T1 line 1 channel group 0 If the port adapter was in port adapter slot O on the VIP this same interface address would be numbered 3 0 0 1 0 Note Although the processor slots in the seven slot Cisco 7507 and the thirteen slot Cisco 7513 chassis are vertically oriented and those in the five slot Cisco 7010 and Cisco 7505 chassis are horizontally oriented all Cisco 7500 series routers use the same method for slot and port numbering PA MC T3 Port Adapter Installation and Configuration OL 2695 05 EEN Chapter1 Overview HZ identifying Interface Addresses PA MC T3 Port Adapter Installation and Configuration EI OL 2695 05
11. eft to the upper right beginning with slot 1 and continuing through slot 2 for the Cisco 7202 slot 4 for the Cisco 7204 and Cisco 7204VXR and slot 6 for the Cisco 7206 and Cisco 7206VXR Port adapters can be installed in any available port adapter slot from 1 through 6 depending on the number of slots in the router Slot 0 is reserved for the I O controller See Figure 1 9 and Figure 1 10 The interface address is composed of a four part number in the format port adapter slot number interface port number t line number channel group number See Table 1 3 For example if a PA MC T3 is installed in slot lof a Cisco 7200 series router the interface address would be 1 0 1 0 port adapter slot 1 interface port 0 T1 line 1 and logical channel group 0 If a PA MC T3 were installed in slot 4 the interface address would be 4 0 1 0 Cisco uBR7200 Series Routers Interface Addresses In the Cisco uBR7223 router only one slot accepts port adapters and it is numbered slot 1 In the Cisco uBR7246 router and Cisco uBR7246VXR router port adapters can be installed in two port adapter slots slot and slot 2 Slot 0 is always reserved for the I O controller if present See Figure 1 11 and Figure 1 12 The interface address is composed of a four part number in the format port adapter slot number interface port number t line number channel group number See Table 1 3 For example if a PA MC TS3 is installed in slot lof a Cisco uBR7223 router the
12. er can be installed into either port adapter slot 0 or slot 1 on a Catalyst RSM VIP2 See Figure 1 6 and Figure 1 7 The interface address is composed of a four part number in the format port adapter slot number interface port number t1 line number channel group number See Table 1 3 For example if a PA MC T3 is installed in port adapter slot 1 of a Catalyst RSM VIP2 in a Catalyst 5000 family switch the interface address would be 1 0 1 0 port adapter slot 1 interface port 0 T1 line 1 and channel group 0 Catalyst 6000 Family FlexWAN Module Interface Addresses amp The Catalyst 6000 family FlexWAN module can be installed in module slots 2 through 9 depending on the number of slots in the router Slot 1 is reserved for the supervisor engine A port adapter can be installed into either port adapter bay 0 or bay 1 on a FlexWAN module See Figure 1 8 The interface address is composed of a five part number in the format module number port adapter bay number interface port number tl line number channel group number See Table 1 3 The first number identifies the module slot of the chassis in which the FlexWAN module is installed slot 2 through slot 3 6 or 9 depending on the number of slots in the chassis These module slots are generally numbered from top to bottom starting with 1 The second number identifies the bay of the FlexWAN module in which the port adapter is installed 0 or 1 The bays are numbered from left to right on t
13. he FlexWAN module The third number identifies the physical port number on the port adapter The PA T3 is a single port port adapter therefore the port number is always 0 The PA MC T3 is a single port port adapter therefore the port is always 0 The fourth number identifies the T1 line number on the PA MC T3 and is a number from 1 through 28 The fifth number identifies the logical channel group on the T1 line and is a number from 0 through 23 For example if a PA MC T3 is installed in the FlexWAN module in module slot 3 port adapter bay 0 the interface address would be 3 0 0 1 0 module slot 3 port adapter bay 0 interface port 0 T1 line 1 logical channel group 0 If the port adapter was in port adapter bay on the FlexWAN module the interface address would be 3 1 0 1 0 Note amp If you remove the FlexWAN module with the PA MC T3 from module slot 3 and install it in module slot 6 port adapter bay 0 the interface address would become 6 0 0 1 0 Note The FlexWAN module physical port address begins with slot 0 which differs from the conventional Catalyst 6000 family port address which begins with slot 1 PA MC T3 Port Adapter Installation and Configuration E OL 2695 05 _ Chapter 1 Identifying Interface Addresses W Cisco 7200 Series Routers and Cisco 7200 VXR Routers Interface Addresses In Cisco 7200 series routers and Cisco 7200 VXR routers port adapter slots are numbered from the lower l
14. hed to its state prior to the out of frame condition that is it reflects the last known state of the far end receiver When the OOF LED is off the FERF LED reflects the live state of the far end receiver After system initialization the ENABLED LED goes on to indicate that the port adapter is enabled for operation The following conditions must be met before the PA MC T3 is enabled e The port adapter is correctly connected to and receiving power from one of the following Catalyst RSM VIP2 motherboard Catalyst 6000 family FlexWAN module VIP e A valid system software image for the port adapter has been downloaded successfully m__PA MC T3 Port Adapter Installation and Configuration OL 2695 05 Chapter1 Overview Cables Connectors and Pinouts W e The system bus recognizes one of the following PA MC T3 Catalyst RSM VIP2 with a PA MC T3 Catalyst 6000 family FlexWAN module with a PA MC T3 VIP with a PA MC T3 If any of the above conditions is not met or if the initialization fails for other reasons the enabled LED does not go on amp Note In addition to the interface status information provided by the LEDs you can also retrieve detailed interface status information either through the router s console port or through Telnet or Simple Network Management Protocol SNMP Cables Connectors and Pinouts The interface connectors on the PA MC T3 are RG 59 coaxial BNC types with one conne
15. interface address would be 1 0 1 0 port adapter slot 1 interface port 0 T1 line 1 and channel group 0 If the PA MC T3 were installed in slot 2 of a Cisco uBR7246 router the interface address would be 2 0 1 0 port adapter slot 2 interface port 0 T1 line 1 and channel group 0 Cisco 7201 Router Interface Addresses In the Cisco 7201 router only one slot accepts port adapters and it is numbered as slot 1 See Figure 1 13 The interface address is composed of a four part number in the format port adapter slot number interface port number t line number channel group number See Table 1 3 For example if a PA MC T3 is installed in a Cisco 7201 router the interface address would be 1 0 1 0 port adapter slot 1 interface port 0 T1 line 1 and channel group 0 Cisco 7301 Router Interface Addresses In the Cisco 7301 router only one slot accepts port adapters and it is numbered as slot 1 See Figure 1 14 The interface address is composed of a four part number in the format port adapter slot number interface port number t1 line number channel group number See Table 1 3 For example if a PA MC T3 is installed in a Cisco 7301 router the interface address would be 1 0 1 0 port adapter slot 1 interface port 0 T1 line 1 and channel group 0 OL 2695 05 PA MC T3 Port Adapter Installation and Configuration jg Chapter1 Overview HZ Identifying Interface Addresses Cisco 7304 PCI Port Adapter Carrier Card Interface Addres
16. lyst RSM VIP2 Slot Numbering page 1 7 e Catalyst 6000 Family FlexWAN Module Slot Numbering page 1 9 e Cisco 7200 Series Routers and Cisco 7200 VXR Routers Slot Numbering page 1 10 e Cisco uBR7200 Series Router Slot Numbering page 1 11 e Cisco 7201 Router Slot Numbering page 1 13 e Cisco 7301 Router Slot Numbering page 1 13 e Cisco 7304 PCI Port Adapter Carrier Card Slot Numbering page 1 14 e Cisco 7401ASR Router Slot Numbering page 1 15 e Cisco 7000 Series Routers and Cisco 7500 Series Routers VIP Slot Numbering page 1 15 Catalyst RSM VIP2 Slot Numbering The Catalyst RSM VIP2 can be installed in any slot in a Catalyst 5000 family switch except the top slots which contain the supervisor engines The Catalyst RSM VIP2 does not use interface processor slot numbering therefore the slots in which it is installed are not numbered A port adapter can be installed into either port adapter slot 0 or slot 1 on a Catalyst RSM VIP2 Figure 1 6 shows a Catalyst 5000 family switch with two port adapters installed in a Catalyst RSM VIP2 Figure 1 6 Catalyst 5000 Family Switch with Port Adapters Installed on Catalyst RSM VIP2 PA MC T3 Port Adapter Installation and Configuration OL 2695 05 E Chapter1 Overview HI Port Adapter Slot Locations on the Supported Platforms ure 1 7 shows two PA MC T3s installed in port adapter slot 0 and slot 1 on a Catalyst RSM VIP2 40 Figure 1 7 Catalyst RSM VIP2 40 with Two PA MC T3s
17. mber Port adapter slot Always 1 1 0 1 0 t1 line number channel group number Interface port O T1 line number 1 through 28 Logical channel group on the T1 line O through 23 PA MC T3 Port Adapter Installation and Configuration iis E OL 2695 05 Chapter1 Overview Identifying Interface Addresses Table 1 3 Identifying Interface Addresses continued Platform Interface Address Format Numbers Syntax Cisco uBR7223 router Port adapter slot number interface port number Port adapter slot Always 1 1 0 1 0 t1 line number channel group number Interface port O T1 line number 1 through 28 Logical channel group on the T1 line 0 through 23 Cisco uBR7246 router Port adapter slot number interface port number _ Port adapter slot 1 or 2 1 0 1 0 t1 line number channel group number Interface port 0 T1 line number 1 through 28 Logical channel group on the T1 line O through 23 Cisco 7301 router Port adapter slot number interface port number Port adapter slot Always 1 1 0 1 0 t1 line number channel group number Interface port O T1 line number 1 through 28 Logical channel group on the T1 line O through 23 Cisco 7304 PCI port Module slot number interface port number Module slot 2 through 5 3 0 1 0 adapter carrier cardin _ t1 line number channel group number Interface port 0 Cisco 7304 router T1 line number 1 through 28 Logical channel group on the T1 line O through 23 Cisco 7401ASR rou
18. ng with slot 1 and continuing through slot 4 You can place a port adapter in any of the slots slot 1 through slot 4 Slot 0 is always reserved for the I O controller The Cisco 7204 router and Cisco 7204VXR are not shown Cisco 7206 routers and Cisco 7206VXR routers including the Cisco 7206 and Cisco 7206VXR routers as router shelves in a Cisco AS5800 Universal Access Server have six slots for port adapters and one slot for an input output I O controller The slots are numbered from the lower left to the upper right beginning with slot 1 and continuing through slot 6 You can place a port adapter in any of the six slots slot 1 through slot 6 Slot 0 is always reserved for the I O controller Figure 1 9 shows the slot numbering on a Cisco 7206 router Figure 1 9 Port Adapter Slots in the Cisco 7206 Router PA MC T3 Port Adapter Installation and Configuration EE OL 2695 05 Chapter1 Overview Port Adapter Slot Locations on the Supported Platforms i Figure 1 10 shows a PA MC T3 in port adapter slot 3 of the Cisco 7206 router Figure 1 10 Cisco 7206 with a PA MC T3 The Cisco 7206VXR router is not shown Cisco uBR7200 Series Router Slot Numbering The Cisco uBR7223 router has one port adapter slot slot 1 Slot 0 is always reserved for the I O controller if present The Cisco uBR7223 router is not shown The Cisco uBR7246 router and Cisco uBR7246VXR router have two port adapter slots slot and slot 2 Slot
19. port adapter in any of the VIP interface slots slot 0 1 4 5 or 6 Slots 2 and 3 are always reserved for RSPs The Cisco 7507 router is not shown Cisco 7513 routers have eleven slots for port adapters and two slots for RSPs The slots are numbered from left to right You can place the port adapter in any of the VIP interface slots slots 0 through 5 or slots 9 through 12 Slots 6 and 7 are always reserved for RSPs The Cisco 7513 router is not shown Interface Addresses This section describes how to identify interface addresses for the PA MC T3 in supported platforms Interface addresses specify the actual physical location of each interface on a router or switch Note that PA MC T3 interface addresses always end with t line number channel group number where e tl line number identifies the T1 line number on the PA MC T3 and is a number from 1 through 28 e channel group number identifies the logical channel group on the T1 line and is a number from 0 through 23 Interfaces on a PA MC T3 installed in a router maintain the same address regardless of whether other port adapters are installed or removed However when you move a port adapter to a different slot the first number in the interface address changes to reflect the new port adapter slot number Interfaces on a PA MC T3 installed in a VIP or FlexWAN module maintain the same address regardless of whether other interface processors or modules are installed or removed However when
20. r of slots in the router The port adapter can be installed in either bay port adapter slot 0 or 1 on the VIP See Figure 1 18 Figure 1 19 and Figure 1 20 The interface address for the VIP is composed of a five part number in the format interface processor slot number port adapter slot number interface port number t line number channel group number See Table 1 3 The first number identifies the slot in which the VIP is installed slot 0 through 12 depending on the number of slots in the router The second number identifies the bay port adapter slot on the VIP in which the port adapter is installed 0 or 1 The bays are numbered from left to right on the VIP The third number identifies the physical port number interface port number on the port adapter The port numbers always begin at 0 and are numbered from left to right The number of additional ports depends on the number of ports on the port adapter The PA MC T3 is a single port port adapter therefore the port is always 0 The fourth number identifies the T1 line number on the PA MC T3 and is a number from through 28 The fifth number identifies the logical channel group on the T1 line and is a number from 0 through 23 PA MC T3 Port Adapter Installation and Configuration P22 OL 2695 05 Chapter1 Overview Identifying Interface Addresses W For example if a PC MC T3 is installed in a VIP in interface processor slot 3 port adapter slot 1 the interface ad
21. ransmit TX You must use 75 ohm RG 59 coaxial interface cables with male BNC connectors to connect the PA MC T3 interface with external T3 equipment For cable information refer to the Cables Connectors and Pinouts section on page 1 5 Any of the 28 T1 lines can be configured as channelized T1 lines You can group the time slots in these T1 lines into several individual logical channel groups each of which carries data with different data link layer protocol encapsulations Each logical channel group can be composed of individual 56 kbps or 64 kbps time slots or individual time slots plus ranges of time slots for example a channel group might be composed of time slots 1 9 and 12 14 Each logical channel group can contain from 1 to 24 time slots maximum the same time slot cannot be used in more than one logical channel group Any unused time slots are filled with programmable idle channel data Each T1 line contains onboard T1 bit error rate test BERT circuitry With this the port adapter software can send and detect programmable patterns and you can run a BERT on any T1 line or all of the 28 T1 lines simultaneously Onboard T3 BER testing is not supported PA MC T3 Port Adapter Installation and Configuration OL 2695 05 Chapter1 Overview Features Features W The PA MC T3 contains the following features e Transmits and receives data bidirectionally at the T3 rate of 44 736 Mbps digital signal ca
22. rried on a T3 line digital signal level 3 DS3 e The T3 connection provided by way of two female BNC connections for transmit TX and receive RX requires RG 59 coaxial cable that has an impedance of 75 ohms e Supports RFC 1406 and RFC 1407 CISCO RFC 1407 CAPABILITY my For RFC 1406 Cisco supports all tables except the Frac table For RFC 1407 Cisco supports all tables except the FarEnd tables For information on accessing Cisco MIB files refer to the Cisco Management Information Base MIB User Quick Reference e PA MC T3 microcode is loaded into and operates from DRAM or SDRAM configuration and is determined by the VIP model on which the PA MC T3 is installed e On the Catalyst RSM VIP2 PA MC T3 microcode is loaded into and operates from DRAM on the Catalyst RSM VIP2 40 Interface Specifications The PA MC T3 T3 port is designed to receive and transmit at the DSX 3 level while driving and receiving from a 75 ohm coaxial cable ATT 728A type coax The T3 port connects directly to any equipment with DSX 3 level BNC connectors Table 1 1 lists the specifications the T3 front end is designed to meet Table 1 1 Specifications for the T3 Front End Parameter Specification Line rate 44 736 Mbps 20 ppm Line code B3ZS bipolar with three zero substitution Impedance 75 ohms Pulse shape ANSI T1 102 pulse amplitude is between 0 36 and 0 85 volts V peak Input signal DSX 3 9 7 dB to 11 8 dB Output
23. ses In the Cisco 7304 router port adapters are installed in a Cisco 7304 PCI port adapter carrier card which installs in Cisco 7304 router module slots 2 through 5 The port adapter slot number is the same as the module slot number SeeFigure 1 15 and Figure 1 16 The interface address is composed of a four part number in the format port adapter slot number interface port number tl line number channel group number See Table 1 3 For example if a PA MC T3 is installed in the Cisco 7304 PCI port adapter carrier card in Cisco 7304 router module slot 3 the interface address would be 3 0 1 0 port adapter slot 3 interface port 0 T1 line 1 and channel group 0 Cisco 7401ASR Router Interface Addresses In the Cisco 7401ASR router only one slot accepts port adapters and it is numbered as slot 1 See Figure 1 17 The interface address is composed of a four part number in the format port adapter slot number interface port number t line number channel group number See Table 1 3 For example if a PA MC T3 is installed in a Cisco 7401ASR router the interface address would be 1 0 1 0 port adapter slot 1 interface port 0 T1 line 1 and channel group 0 Cisco 7000 Series Routers and Cisco 7500 Series Routers VIP Interface Addresses In Cisco 7000 series routers and Cisco 7500 series routers port adapters are installed on a versatile interface processor VIP which installs in interface processor slots 0 through 12 depending on the numbe
24. talls into Cisco 7304 router module slots 2 through 5 Figure 1 15 shows the module slot numbering on a Cisco 7304 router The port adapter slot number is the same as the module slot number Slot 0 and slot are reserved for the NPE module or NSE module sure 1 16 shows a Cisco 7304 PCI port adapter carrier card with a port adapter installed The Cisco 7304 PCI port adapter carrier card accepts one single width port adapter Figure 1 15 Module Slots on the Cisco 7304 Router Figure 1 16 Cisco 7304 PCI Port Adapter Carrier Card Port Adapter Installed PA MC T3 Port Adapter Installation and Configuration iis OL 2695 05 Chapter1 Overview Port Adapter Slot Locations on the Supported Platforms i Cisco 7401ASR Router Slot Numbering Figure 1 17 shows the front view of a Cisco 7401 ASR router with a port adapter installed There is only one port adapter slot slot 1 in a Cisco 7401ASR router Figure 1 17 Port Adapter Slot in Cisco 7401ASR Router Cisco 7000 Series Routers and Cisco 7500 Series Routers VIP Slot Numbering The PA MC T3 is supported on the VIP2 and VIP4 versatile interface processors used in Cisco 7000 series and Cisco 7500 series routers In the Cisco 7010 router and Cisco 7505 router the VIP motherboard is installed horizontally in the VIP slot In the Cisco 7507 router and Cisco 7513 router the VIP motherboard is installed vertically in the VIP slot The port adapter can be installed in either bay pori
25. ter Port adapter slot number interface port number Port adapter slot Always 1 1 0 1 0 t1 line number channel group number Interface port O T1 line number 1 through 28 Logical channel group on the T1 line O through 23 VIP in Cisco 7000 Interface processor slot number port adapter slot Interface processor slot 0O 3 1 0 1 0 series routers or Cisco 7500 series router number interface port number t line number channel group number through 12 depends on the number of slots in the router Port adapter slot 0 or 1 Interface port 0 T1 line number 1 through 28 Logical channel group on the T1 line 0 through 23 1 Slot 1 is reserved for the supervisor engine If a redundant supervisor engine is used it must go in slot 2 otherwise slot 2 can be used for other modules 2 Port adapter slot 0 is reserved for the Fast Ethernet port on the I O controller if present OL 2695 05 PA MC T3 Port Adapter Installation and Configuration gy Chapter1 Overview HZ Identifying Interface Addresses Catalyst RSM VIP2 Interface Addresses in the Catalyst 5000 Family Switches In Catalyst 5000 family switches the Catalyst RSM VIP2 can be installed in any slot except the top slots which contain the supervisor engine modules The Catalyst RSM VIP2 in a Catalyst 5000 family switch does not use interface processor slot numbering therefore the slots in which it is installed are not numbered A port adapt
26. ter Installation and Configuration OL 2695 05 EN Chapter1 Overview Hs Cables Connectors and Pinouts Figure 1 3 Attaching the Ferrite Sleeve Around a Coaxial Cable Figure 1 4 shows the typical 75 ohm RG 59 coaxial cable pair that you supply and should use with the PA MC T3 Use only this type of coaxial cable pair for your PA MC T3 connections Use one 75 ohm coaxial cable for each PA MC T3 connection RX and TX We strongly recommend that you fasten together your transmit and receive cables along their entire length as shown in Figure 1 4 which reduces the effects of EMI You can use standard heat activated shrink tubing or cable ties for this purpose Figure 1 4 75 Ohm RG 59 Coaxial Cable Pair with Ferrite Sleeves Attached You can also order from Cisco Systems a 75 ohm coaxial cable pair with ferrite beads attached Cisco Product Number CAB ATM DS3 E3 See Figure 1 5 This 75 ohm coaxial cable pair is not available from outside commercial cable vendors Figure 1 5 CAB ATM DS3 E3 Cable 75 Ohm RG 59 Coaxial Cable with BNC Connectors PA MC T3 Port Adapter Installation and Configuration OL 2695 05 Chapter1 Overview Port Adapter Slot Locations on the Supported Platforms W Port Adapter Slot Locations on the Supported Platforms This section discusses port adapter slot locations on the supported platforms The illustrations that follow summarize slot location conventions on each platform e Cata
Download Pdf Manuals
Related Search