Asrock K7UPGRADE-880 motherboard
Contents
1. 2x USB 2 0 Ports USB0 USB1 2x USB 2 0 Ports USB2 USB3 Serial Port COM1 PS 2 Keyboard Port Purple PS 2 Mouse Port Green 2 Installation K7Upgrade 880 is an ATX form factor 12 0 in x 8 5 in 30 5 cm x 21 6 cm motherboard Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it Pre installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings Before you install or remove any component ensure that the L power is switched off or the power cord is detached from the power supply Failure to do so may cause severe damage to the motherboard peripherals and or components 1 Unplug the power cord from the wall socket before touching any component 2 To avoid damaging the motherboard components due to static electricity NEVER place your motherboard directly on the carpet or the like Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any component place it on a grounded anti static pad or in the bag that comes with the component 5 When placing screws into the screw holes to secure the motherboard to the chassis please do not over tighten the screws Doing so may damage the motherboard 10 2 1 CPU Installation Step 12. Serial ATA Floppy Port Audio LAN Hardware Monitor K8 Bridge PCI slots AGP slots USB 2 0 ATX Form Factor 12 0 in x 8 5 in 30 5 cm x 21 6 cm 462 Pin Socket Supporting AMD Athlon Athlon XP Duron and 32 bit Sempron Processor North Bridge VIA KT880 FSB 400 MHz South Bridge VIA VT8237 supports USB 2 0 ATA 133 SATA 1 5Gb s 4 DDR DIMM Slots DDR1 DDR2 DDR3 and DDR4 Support PC3200 DDR400 PC2700 DDR333 PC2100 DDR266 Max 4GB Dual Channel Memory Technology support see CAUTION 1 IDE 1 ATA 133 Ultra DMA Mode 6 IDE2 ATA 133 Ultra DMA Mode 6 Support up to 4 IDE devices 2 SATA connectors Support 1 5Gb s data transfer rate Supports up to 2 floppy disk drives 5 1 channels AC 97 Audio Speed 802 3u 10 100 Ethernet supports Wake On LAN CPU Temperature Sensing Motherboard Temperature Sensing CPU Overheat Shutdown to Protect CPU Life ASRock U COP see CAUTION 2 CPU Fan Tachometer Chassis Fan Tachometer Voltage Monitoring 12V 5V 3 3V Vcore Supports CPU upgrade from AMD K7 462 Pin CPU to AMD K8 754 Pin CPU see page 14 for details 3 slots with PCI Specification 2 3 2 AGP slots support 1 5V 8X 4X AGP card see CAUTION 3 1 5V AGP1 supports for K7 AGP Interface AGP2 supports for K8 AGP Interface 8 USB 2 0 ports include 6 ready to use USB 2 0 ports on the rear panel plus one on board header supporting 2 extra USB 2 0 ports see CAUTION 4 ASRock I O Plus 1 PS 2 mouse p
3. What is Hot Plug Function If the SATA HDDs are NOT set for RAID configuration it is called Hot Plug for the action to insert and remove the SATA HDDs while the system is still power on and in working condition However please note that it cannot perform Hot Plug if the OS has been installed into the SATA HDD What is Hot Swap Function If SATA HDDs are built as RAID1 then it is called Hot Swap for the action to insert and remove the SATA HDDs while the system is still power on and in working condition 21 2 9 Making An SATA Driver Diskette If you want to install Windows 2000 or Windows XP on your SATA HDDs you will need to make an SATA driver diskette before you start the OS installation STEP 1 Insert the ASRock Support CD into your optical drive to boot your system Do NOT insert any floppy diskette into the floppy drive at this moment STEP 2 During POST at the beginning of system boot up press lt F11 gt key and then a window for boot devices selection appears Please select CD ROM as the boot device STEP 3 When you see the message on the screen Do you want to generate Serial ATA driver diskette YN press lt Y gt STEP 4 Then you will see these messages STEP 5 Please insert a diskette into the floppy drive WARNING Formatting the floppy diskette will lose ALL data in it Start to format and copy files YN Please insert a floppy diskette into the floppy drive and press
4. DRAM CAS Latency Auto 166MHz DDR333 DRAM Command Rate 2T Command 200MHz DDR400 DRAM Bus Selection Auto Auto Primary Graphics Adapter PCI AGP Aperture Size 64MB AGP Mode Auto Sel s AGP Fast Write Disabled elect Screen IDE Drive Strength Normal geet ear PCI Delay Transaction Disabled ange Option OnBoard LAN Enabled General Help OnBoard AC 97 Audio Enabled ee S ESC Exit v02 54 C Copyright 1985 2003 American Megatrends Inc DRAM Frequency If Auto is selected the motherboard will detect the memory module s inserted and assigns appropriate frequency automatically You may also select other value as operating frequency 133MHz DDR 266 166MHz DDR 333 200MHz DDR 400 Flexibility Option The default value of this option is Disabled It will allow better tolerance for memory compatibility when it is set to Enabled DRAM CAS Latency Use this item to adjust the means of memory accessing Configuration options Auto 2 5 2 and 3 DRAM Command Rate Use this to select among 2T Command and 1T Command for DRAM Command Rate The default value is 2T Command DRAM Bus Selection The default value is Auto which will automatically select the proper ac cess mode for the system You may select between Single Channel and Dual Channel if you have properly set the dual channel memory configuration Primary Graphics Adapter This allows you to select PCI or AGP as t
5. lt Y gt The system will start to format the floppy diskette and copy SATA drivers into the floppy diskette Once you have the SATA driver diskette ready you may start to install Windows 2000 Windows XP on your system directly without setting the RAID configura tion on your system or you may start to use VT8237 SATA RAID BIOS to set RAID 0 RAID 1 JBOD configuration before you install the OS Before you start to configure the RAID function you need to check the installation guide in the Support CD for proper configuration Please refer to the document in the Support CD Guide to SATA Hard Disks Installation and RAID Configuration which is located in the folder at the following path SATA RAID BIOS You may also set the RAID configuration by using VIA RAID Tool in Windows environment Please refer to the document in the Support CD Guide to VIA RAID Tool which is located in the folder at the following path VIA RAID Tool 22 3 BIOS SETUP UTILITY 3 1 Introduction This section explains how to use the BIOS SETUP UTILITY to configure your system The Flash Memory on the motherboard stores the BIOS SETUP UTILITY You may run the BIOS SETUP UTILITY when you start up the computer Please press lt F2 gt during the Power On Self Test POST to enter the BIOS SETUP UTILITY otherwise POST will continue with its test routines If you wish to enter the BIOS SETUP UTILITY after POST restart the system by
6. 200MHz FSB 266MHz FSB 333MHz FSB 400MHz Note The setting of the CPU front side bus frequency of this motherboard is by means of the adjustment of jumper setting To perform over clocking you must set the FSB jumper according to your AMD CPU before you use the Manual option as the FSB setting in BIOS setup Please follow the figures above to set the CPU front side bus frequency 16 CPU Multiplier Jumper J1 5 x 3 pin see p 8 No 3 Note The set of CPU Multiplier Jumper is only for advanced users to adjust the multiplier of CPU Please follow the table below to adjust the multiplier of CPU However the system will work well without the adjustment of multiplier You do not have to adjust the multiplier for normal usage Multiplier FIDO FID1 FID2 FID3 FID4 5x 2 3 2 3 1 2 2 3 2 3 5 5x 1 2 2 3 1 2 2 3 2 3 6x 2 3 1 2 1 2 2 3 2 3 6 5x 1 2 1 2 1 2 2 3 2 3 7x 2 3 2 3 2 3 1 2 2 3 7 5x 1 2 2 3 2 3 1 2 2 3 8x 2 3 1 2 2 3 1 2 2 3 8 5x 1 2 1 2 2 3 1 2 2 3 9x 2 3 2 3 1 2 1 2 2 3 9 5x 1 2 2 3 1 2 1 2 2 3 10x 2 3 1 2 1 2 1 2 2 3 10 5x 1 2 1 2 1 2 1 2 2 3 11x 2 3 2 3 2 3 2 3 2 3 11 5x 1 2 2 3 2 3 2 3 2 3 12x 2 3 1 2 2 3 2 3 2 3 12 5x 1 2 1 2 2 3 2 3 2 3 13x 2 3 2 3 1 2 2 3 1 2 13 5x 1 2 2 3 1 2 2 3 1 2 14x 2 3 1 2 1 2 2 3 1 2 15x 2 3 2 3 2 3 1 2 1 2 16x 2 3 1 2 2 3 1 2 1 2 16 5x 1 2 1 2 2 3 1 2 1 2 17x 2 3 2 3 1 2 1 2 1 2 18x 1 2 2 3 1 2 1 2 1 2 19x 1 2 2 3 2 3 2 3 1 2 20x 1 2 1 2 2 3 2 3 1 2 21x 1 2 1 2 1 2 2 3 1 2 2
7. CPU host frequency of this motherboard is determined by the jumper setting To perform over clocking you must set the FSB jumper according to your AMD CPU before you use the Manual option as the FSB setting in BIOS setup Please check page 26 for details 1 3 Motherboard Layout 234 5 Od 21 6cm 8 5 in 1Ps usa pms H 1 al arxiv i Z9v 139008 k 8 ma Eile Elz z sees alls alle l ail 5 EA EE S Zil G 5 Z alje a re S s z A z 9 X Audio lt 0 37 2a som 1 5V AGP1 36 4 PHY 2 35 ite 3 34 K8BRIDGE_1 7 EEE K7Upgrade 880 3 Super er 6 32 51CH AGP2 n ASRock rsg400 e 7 PCI 1 VIA 31 Bios USB2 0 VT8237 ad PCI 2 ER 8 30 ATAI33 rLopPy1 9 DDR400 cmos PCI 3 20 AGPEX m Uae anaa NELS 21 SATA GEE EI ne es 29 28 27 26 25 24 23 22 1 PS2 USB PWR1 Jumper 21 Chassis Fan Connector CHA FAN1 2 CPU Fan Connector CPU FAN1 22 System Panel
8. Header PANEL1 3 CPU Multiplier Jumper J1 23 Power LED Header PWR LED1 4 CPU Socket 24 Chassis Speaker Header SPEAKER 1 5 North Bridge Controller 25 USB 2 0 Header USB67 Blue 6 ATX 12V Connector ATX12V1 26 Clear CMOS Jumper CLRCMOS2 7 2x184 pin DDR DIMM Slots 27 South Bridge Controller Dual Channel A DDR1 DDR3 Blue 28 Infrared Module Header IR1 8 Secondary IDE Connector IDE2 Black 29 Game Port Connector GAME1 9 Primary IDE Connector IDE1 Blue 30 3xPCI Slots PCI1 3 10 FSB Select Jumpers FSB SELO0 FSB SEL1 31 Flash Memory 11 2x184 pin DDR DIMM Slots 32 AGP Slot AGP2 Dual Channel B DDR2 DDR4 Black 33 J6 Jumper 5 x 2 Pin 12 J2 J3 J14 Jumpers 3 sets of 1 x 2 Pin 34 Future CPU Bridge K8BRIDGE 1 13 J5 J4 Jumpers 2 sets of 8 x 2 Pin 35 Front Panel Audio Header AUDIO1 14 J9 J10 J11 J13 Jumper 5 sets of 1 x 3 Pin 36 JR1 JL1 Jumpers 15 Future CPU Bridge KSBRIDGE 2 37 AGP Slot 1 5V AGP1 16 J8 J7 Jumpers 2 sets of 5x3 Pin 38 ATX Power Connector ATXPWR1 17 Secondary Serial ATA Connector SATA2 39 Internal Audio Connector AUX1 White 18 Primary Serial ATA Connector SATA1 40 Internal Audio Connector CD1 Black 19 J12 Jumper 4x 3 Pin 41 Shared USB 2 0 Header USB45 Blue 20 Floppy Connector FLOPPY1 1 4 ASRock I O Plus oahowon VG i 7 2 IQ Parallel Port RJ 45 Port Line In Light Blue Line Out Lime Microphone Pink 2x Shared USB 2 0 Ports USB4 USB5 10 11
9. Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc CPU Host Frequency While entering setup BIOS auto detects the present CPU host frequency of this motherboard The actual CPU host frequency will show in the following item Spread Spectrum This item should always be Disabled for better system stability If you use an AMD 754 Pin CPU on the ASRock 754Bridge which is installed into the K8 BRIDGE on this motherboard you will see the below screens and configuration options for the CPU Configuration BIOS SETUP UTILITY Advanced CPU Configuration Select how to set the CPU host frequency Actual Frequency MHz 200 Spread Spectrum Disabled Cool n Quiet Enabled Processor Maximum Multiplier xil Processor Maximum Voltage 1 550 V Multiplier Voltage Change Auto Memory Clock Auto Flexibility Option Disabled Bank Interleaving Auto Select Screen Burst Length 8 Beats Select Item CAS Latency CL Auto Change Option TRCD Auto General Help TRAS Auto Load Defaults TRP Auto Save and Exit MA Timing 2T Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 26 CPU Host Frequency While entering setup BIOS auto detects the present CPU host frequency of this motherboard The actual CPU host frequency will show in the following item Spread Spectrum This item should always be Disabled for better system stab
10. SRock K7Upgrade 880 User Manual Version 1 0 Published August 2004 Copyright 2004 ASRock ING All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of business and the like even if ASRock has been advised of t
11. Step 2 Step 3 AN Step 4 Unlock the socket by lifting the lever up to a 90 angle Position the CPU directly above the socket such that its marked corner matches the base of the socket lever Carefully insert the CPU into the socket until it fits in place The CPU fits only in one correct orientation DO NOT force the CPU into the socket to avoid bending of the pins When the CPU is in place press it firmly on the socket while you push down the socket lever to secure the CPU The lever clicks on the side tab to indicate that it is locked Step 2 3 Step 4 2 2 Installation of CPU Fan and Heatsink After you install the CPU into this motherboard it is necessary to install a larger heatsink and cooling fan to dissipate heat You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation Make sure that the CPU and the heatsink are securely fas tened and in good contact with each other Then connect the CPU fan to the CPU FAN connector CPU_FAN1 see Page 8 No 2 For proper installation please kindly refer to the instruction manuals of the CPU fan and the heatsink 11 2 3 Installation of Memory Modules DIMM K7Upgrade 880 motherboard provides four 184 pin DDR Double Data Rate DIMM slots and supports Dual Channel Memory Technology For dual channel configuration you always need to install identical the same brand speed size and chip type DDR DIMM pair in the s
12. are used to install a graphics card Please insert the AGP card with K7 AGP Interface into the slot 1 5V_AGP1 see page 8 No 37 or insert the AGP card with K8 AGP Interface into the slot AGP2 see page 8 No 32 Please do not install AGP cards into the slot 1 5V_AGP1 and the slot AGP2 at the same time It may cause permanent damage to the hardware Please do NOT use a 3 3V AGP card on the AGP slot of this motherboard It may cause permanent damage For the voltage information of your AGP card please check with the AGP card vendors Installing an expansion card Step 1 Before installing the expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Step 2 Remove the system unit cover if your motherboard is already installed in a chassis Step 3 Remove the bracket facing the slot that you intend to use Keep the screws for later use Step 4 Align the card connector with the slot and press firmly until the card is completely seated on the slot Step 5 Fasten the card to the chassis with screws Step 6 Replace the system cover 15 2 5 Jumpers Setup The illustration shows how jumpers are setup When the jumper cap is placed on pins the jumper is Short If no jumper cap 4 4 is placed on pins the jumper is Open The illustration
13. pressing lt Ctl gt lt Alt gt lt Delete gt or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on Because the BIOS software is constantly being updated the following BIOS setup screens and descriptions are for reference purpose only and they may not exactly match what you see on your screen 3 1 1 BIOS Menu Bar The top of the screen has a menu bar with the following selections Main To set up the system time date information Advanced To set up the advanced BIOS features H W Monitor To display current hardware status Boot To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the BIOS SETUP UTILITY Use lt lt gt key or lt gt key to choose among the selections on the menu bar and then press lt Enter gt to get into the sub screen 23 3 1 2 Navigation Keys Please check the following table for the function description of each navigation key Navigation Key s gt try lt Enter gt lt F1 gt lt F9 gt lt F10 gt lt ESC gt 3 2 Main Screen When you enter the BIOS the system overview Advanced System Overview System Date BIOS Version K7Upgrade BIOS P1 00 Processor Type AMD Athlon tm XP 2600 Processor J 2083 MHz L1 Cache Siz 64KB L2 Cache Size 256KB Total Memory 512MB Dual Channel Me
14. to optimize compatibility and performance please connect your hard disk drive to the primary IDE connector IDE1 blue and CD ROM to the secondary IDE connector IDE2 black connectors support SATA data cables for internal storage devices The current SATA Serial ATA Connectors SATA2 These two Serial ATA SATA SATA1 see p 8 No 18 SATA2 see p 8 No 17 SATA1 i interface allows up to 1 5 Gb s data transfer rate Serial ATA SATA Either end of the SATA data Data Cable cable can be connected to the SATA hard disk or the SATA connector on the motherboard 18 Serial ATA SATA Power Cable nl Optional connect tothe SATA HDD power connector connect to the power supply Please connect the black end of SATA power cable to the power connector on the drive Then connect the white end of SATA power cable to the power connector of the power supply USB 2 0 Header 9 pin USB67 see p 8 No 25 ASRock I O Plus provides you 6 ready to use USB 2 0 ports on the rear panel If the rear USB ports are not sufficient this USB 2 0 header is available to support 2 extra USB 2 0 ports Shared USB 2 0 Header 1 USB_PWR This USB45 connector is shared 9 pin USB45 ey Tole he with the USB 2 0 ports 4 5 on see p 8 No 41 ad ASRock I O Plus When using DUMMY the front panel USB ports by attaching the front panel USB cable to this connecto
15. 2x 1 2 2 3 2 3 1 2 1 2 23x 2 3 1 2 1 2 1 2 1 2 24x 1 2 1 2 1 2 1 2 1 2 For example Athlon XP 2000 is an 1666MHz CPU 12 5 Multiplier X 133MHz External frequency 1666MHz FID jumpers setting The jumper caps are not provided by ASRock Please understand that ASRock does not guarantee and support the adjustment of multiplier These jumpers setting may not apply to all multiplier locked or even some unlocked AMD CPU Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU 17 2 6 Onboard Headers and Connectors j fA Onboard headers and connectors are NOT jumpers Do NOT place jumper caps over these headers and connectors Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard FDD Connector 33 pin FLOPPY1 see p 8 No 20 the red striped side to Pin1 Note Make sure the red striped side of the cable is plugged into Pin1 side of the connector Primary IDE Connector Blue Secondary IDE Connector Black 39 pin IDE1 see p 8 No 9 39 pin IDE2 see p 8 No 8 connect the blue end C AN a N connect the black end brud to the motherboard to the IDE devices 80 conductor ATA 66 100 133 cable Note If you use only one IDE device on this motherboard please set the IDE device as Master Please refer to the instruction of your IDE device vendor for the details Besides
16. Contact Information seenronernrnvvrrvrrnrnnrrnrerrervnrnnenr 42 1 Introduction Thank you for purchasing ASRock K7Upgrade 880 motherboard a reliable motherboard produced under ASRock s consistently stringent quality control It de livers excellent performance with robust design conforming to ASRock s commit ment to quality and endurance In this manual chapter 1 and 2 contain introduction of the motherboard and step by step guide to the hardware installation Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD Because the motherboard specifications and the BIOS software might be updated the content of this manual will be subject to change without notice In case any modifications of this manual occur the updated version will be available on ASRock website without further notice You may find the latest memory and CPU support lists on ASRock website as well ASRock website http www asrock com 1 1 Package Contents ASRock K7Upgrade 880 Motherboard ATX Form Factor 12 0 in x 8 5 in 30 5 cm x 21 6 cm ASRock K7Upgrade 880 Quick Installation Guide ASRock K7Upgrade 880 Support CD One 80 conductor Ultra ATA 66 100 133 IDE Ribbon Cable One Ribbon Cable for a 3 5 in Floppy Drive One Serial ATA SATA Data Cable One Serial ATA SATA HDD Power Cable Optional One ASRock I O Plus Shield One Jumper Cap Remover 1 2 Specifications Platform CPU Chipsets Memory IDE
17. Megatrends Inc 38 3 5 1 Boot Settings Configuration BIOS SETUP UTILITY Boot Settings Configuration To enable or disable the boot from network feature Bootup Num Lock Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Boot From Network Use this item to enable or disable the Boot From Network feature Boot Up Num Lock If this item is set to On it will automatically activate the Numeric Lock function after boot up 3 5 2 Boot Device Priority In this section you may specify the boot sequence from the available devices in your system BIOS SETUP UTILITY Boot Device Priority Specifies the boot sequence from the available devices 2nd Boot Device HDD PM MAXTOR 6L08 3rd Boot Device CD DVD A device enclosed in parenthesis has been disabled in the corresponding type menu Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Likewise you may also specify the boot sequence from the available devices for the hard disk drives the removable drives and the CD DVD drives 39 3 6 Security Screen In this section you may set or change the supervisor user password for the system For the user password you may also clear it BIOS SETUP UTILITY Advanced H W Monitor Boot Securit
18. Menu Bar ainra nnii tannamann ia 23 3 1 2 Navigation Keys urnrsvrrrvrnrrernvervennvennvennvrnvevrvverrer 24 3 2 Main Screen 3 3 Advanced Screen 3 3 1 CPU Configuration esvrnrnrvrrnennrrrrrnrerrrrvrrnerrrrsrener 3 3 2 Chipset Configuration seeen 3 3 3 ACPI Configuration s asorrvrrnrnrrvernrnnrrnrnnvervnrvnrne 3 3 4 IDE Configuration ervernrrvornrnvnrrvrnnennrrnrnnvrrvnrvnnne 3 3 5 PCIPnP Configuration rrrernrnvnrrvrrnennrrnrrnvrrvnrvnnnee 3 3 6 Floppy Configuration srrvrernrnnnnrnnvrrvrrvnnnennrrnnener 3 3 7 Super IO Configuration 3 3 8 USB Configuration 0 0 cee eeeeeeeeeeeeeeeeeeneeeeeeeeens 3 4 Hardware Health Event Monitoring Screen sses 38 3 5 BOOtSCree hh vtec tesco entice and aaa iN 38 3 5 1 Boot Settings Configuration s e 39 3 5 2 Boot Device Priority rrrronrrnnnnvnnnnnrnnennrnnnnrrnnnnnenrn 39 3 6 Security Screen usrrrrnnrnrnnnnonnvnnrrrevnnrnnnnnnnvevsenesrrnnnnsnenen 40 3 7 EXtSCreen mannnnsmstdgnndssnntnt avsnitt 41 4 Software Support rrrrrrrrnvvrrrrvrrvnverrrrrrrrrrenener 42 4 1 Install Operating System rrnrrnrnnnnrvnnnvnvvvrrnvnnrvnrnennrrrrnssenn 42 4 2 Support CD Information ersvrnvrrvvrvnnnrnnrrnrnnrnrvernernrrrrrrsenr 42 4 2 1 Running Support CD neseser 42 4 2 2 Drivers Menu eiernssernsvensrensrenssasernarnenennnernnvnnseneser 42 4 2 3 Utilities Menu reerearnnaevnnernevnnsvnnennavnnnevnnsenavrnnevnnenne 42 4 2 4
19. Port Address Use this item to set the address for the onboard parallel port or disable it Configuration options Disabled 378 and 278 Parallel Port Mode Use this item to set the operation mode of the parallel port The default value is ECP EPP If this option is set to ECP EPP it will show the EPP version in the following item EPP Version Configuration options Normal Bi Directional and ECP EPP EPP Version Use this item to set the EPP version Configuration options 1 9 and 1 7 ECP Mode DMA Channel Use this item to set the ECP mode DMA channel Configuration options DMAO DMA1 and DMA3 Parallel Port IRQ Use this item to set the IRQ for the parallel port Configuration options IRQ5 and IRQ7 36 OnBoard Game Port Use this item to enable the Game Port or disable it OnBoard MIDI Port Use this itme to select the address for the MIDI Port or disable it Configura tion options Disabled 300 and 330 3 3 8 USB Configuration BIOS SETUP UTILITY Advanced USB Configuration To enable or disable the onboard USB controllers USB 2 0 Support Enabled Legacy USB Support Disabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc USB Controller Use this item to enable or disable the use of USB controller USB 2 0 Support Use this item to enable or disable the USB 2 0 sup
20. Power On Use this item to enable or disable Ring In signals to turn on the system from the power soft off mode PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power soft off mode PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to power on the system 32 3 3 4 IDE Configuration BIOS SETUP UTILITY Advanced DISABLED disables the integrated IDE Controller PRIMARY enables only the Primary IDE gt Primary IDE Master Hard Disk Controller gt Primary IDE Slave Not Detected SECONDARY enables p Secondary IDE Master Not Detected only the Secondary IDE gt Secondary IDE Slave Not Detected Controller BOTH enables both IDE Controllers IDE Configuration Select Screen td Select Item Change Option F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit v02 54 C Copyright 1985 2003 American Megatrends Inc OnBoard IDE Controller You may enable either the primary IDE channel or the secondary IDE channel Or you may enable both the primary and the secondary IDE channels by selecting Both Set to Disabled will disable the both Configuration options Disabled Primary Secondary Both IDE Device Configuration You may set the IDE configuration for the device that you speci
21. a Device such as MO LBA Large Mode Use this item to select the LBA Large mode for a hard disk gt 512 MB under DOS and Windows for Netware and UNIX user select Disabled to disable the LBA Large mode Block Multi Sector Transfer The default value of this item is Auto If this feature is enabled it will enhance hard disk performance by reading or writing more data during each transfer PIO Mode Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing DMA Mode DMA capability allows the improved transfer speed and data integrity for compatible IDE devices S M A R T Use this item to enable or disable the S M A R T Self Monitoring Analysis and Reporting Technology feature Configuration options Disabled Auto Enabled 32 Bit Data Transfer Use this item to enable 32 bit access to maximize the IDE hard disk data transfer rate 34 3 3 5 PCIPNP Configuration BIOS SETUP UTILITY PCI PnP Configuration Value in units of PCI clocks for PCI device latency timer register PCI IDE BusMaster Enabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc PCI Latency Timer The default value is 32 It is recommended to keep the default value unless the installed PCI expansion cards specifications require other settings PCI IDE BusMaster Use this item to enable o
22. ct power supply before adding or removing DIMMs or the system components Step 1 Unlock a DIMM slot by pressing the retaining clips outward Step 2 Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot EEE lt break notch break D The DIMM only fits in one correct orientation It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation Step 3 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 13 2 4 Expansion Slots K8 Bridge PCI Slots and AGP Slots There are 1 set of K8 Bridge 3 PCI slots and 2 AGP slots the slot 1 5V_AGP1 supports for K7 AGP Interface and the slot AGP2 supports for K8 AGP Interface on K7Upgrade 880 motherboard K8 Bridge Orange Colored Bridge K8BRIDGE 1 Brown Colored Bridge K8BRIDGE_2 The set of K8 Bridge allows you to upgrade your AMD 462 Pin CPU to AMD 754 Pin CPU by installing an add on ASRock 754Bridge optional into this K8 Bridge on K7Upgrade 880 motherboard Before you upgrade the AMD 462 Pin CPU to the AMD 754 Pin CPU it is necessary to adjust the jumper settings for those required jumpers on K7Upgrade 880 motherboard Please refer to the table below for the correct jumper settings The orange colored Bridge K8BRIDGE_1 is not an AGP slot and the brown colored Bridge K8BRIDGE 2 is not a
23. fy We will use the Primary IDE Master as the example in the following instruction which can be applied to the configurations of Primary IDE Slave Sec ondary IDE Master and Secondary IDE Slave as well BIOS SETUP UTILITY Advanced Primary IDE Master Select the type of device connected Device zl i to the system Vendor Size LBA Mode Block Mode PIO Mode Asyne DMA ultiWord DMA 2 Ultra DMA tra DMA 5 S M A R T Supported Select Screen LBA Large Mode Auto Select Item Block Multi Sector Transfer Auto PIO ae Auto Change Option DMA Mode Auto General Help S M A R T Disabled Load Defaults 32Bit Data Transfer Disabled Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 33 TYPE Use this item to configure the type of the IDE device that you specify Configuration options Not Installed Auto CD DVD and ARMD Not Installed Select Not Installed to disable the use of IDE device Auto Select Auto to automatically detect the hard disk drive After selecting the hard disk information into BIOS use a disk utility such as FDISK to partition and format the new IDE hard disk drives This is necessary so that you can write or read data from the hard disk Make sure to set the partition of the Primary IDE hard disk drives to active CD DVD This is used for IDE CD DVD drives ARMD This is used for IDE ARMD ATAPI Removable Medi
24. grade 880 W 754Bridge BIOS P1 0 Processor Type AMD Athlon tm 64 Processor 3400 Processor Speed 2200 MHz LI Cache Size 128KB Select Screen L2 Cache Size 1024KB Select Item Change Field Total Memory 256MB Select Field DDR 1 256MB 166MHz DDR333 General Help DDR 2 None Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 3 3 Advanced Screen In this section you may set the configurations for the following items CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperlO Configuration and USB Configuration BIOS SETUP UTILITY Advanced WAA O Security Advanced Settings Configure CPU WARNING Setting wrong values in below sections may cause system to malfunction gt Chipset Configuration gt ACPI Configuration gt IDE Configuration gt PCIPnP Configuration gt Floppy Configuration ve erect SOE gt SuperIO Configuration tt fees re p Enter Go to Sub Screen gt USB Configuration Fi General Heip F9 Load Defaults F10 Save and Exit ESC Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Setting wrong values in this section may cause the system to malfunction 25 3 3 1 CPU Configuration BIOS SETUP UTILITY Advanced CPU Configuration Select how to set the CPU host frequency Actual Frequency MHz 166 Spread Spectrum Disabled Select Screen Select
25. hat are not PCI 2 1 compliant OnBoard LAN This allows you to enable or disable the onboard LAN feature OnBoard AC 97 Audio Select Enabled or Disabled for the onboard AC 97 Audio feature HT Width You may set the HyperTransport width as 8 bit 16 bit or Auto The default value is Auto HT Speed You may set the HyperTransport speed as Auto 200 MHz 400 MHz 600 MHz or 800 MHz The default value is Auto 31 3 3 3 ACPI Configuration BIOS SETUP UTILITY Advanced ACPI Configuration Select auto detect or Bes disable the STR feature Restore on AC Power Loss Power Off Ring In Power On Disabled PCI Devices Power On Disabled PS 2 Keyboard Power On Disabled RTC Alarm Power On Disabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Suspend to RAM Use this item to select whether to auto detect or disable the Suspend to RAM feature Select Auto will enable this feature if the OS supports it If you set this item to Disabled the function Restore on AC Power Loss will be hidden Restore on AC Power Loss Use this item to set the power state after an unexpected AC power loss If Power Off is selected the AC power remains off when the power recovers If Power On is selected the AC power resumes and the sys tem starts to boot up when the power recovers Ring In
26. he possibility of such damages arising from any defect or error in the manual or product FC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation ASRock Website http www asrock com Contents Introduetlon hm eissesesvsesevivsnnunsnsnnegnnnadedar 5 1 1 Package Contents mrmrrrnrennrrvvnnvnnnnrnrnnrrrvrnvernnrnernernrensensne 5 1 2 Specitications su saa 6 1 3 Motherboard Layout saversvrnnvrnnvrnrvrnnvrnrvenvvrnnvnnnvenrvenvvnsne 8 1 4 ASRock I O Plus tretten 9 Installatlon 5 usa tiene eens 10 Pre installation Precautions wasrvsnrnnnvnnnrnrnvnrvvvnnvennrnnvvenvvensreen 10 24 CPU Installation x uunsesearessaseea teist 11 2 2 Installation of CPU Fan and Heatsink s e 11 2 3 Installation of Memory Modules DIMM cee 12 2 4 Expansion Slots K8 Bridge PCI and AGP Slots 00 14 2 5 Jumpers Setup cinsore a enere 16 2 6 Onboard Headers and Connectors ssec 18 2 7 Serial ATA SATA Hard Disks Installation 0 0 0 0 cece 21 2 8 Hot Plug and Hot Swap Functions for SATA HDDs 21 2 9 Making An SATA Driver Diskette aeee 22 BIOS SETUP UTILITY nnnrrnnnrnnnerrnnrrrsnnnnnnnvvrnnernnnn 23 3 1 Introduction iesin iranieni eiivet 23 3 1 1 BIOS
27. he primary graphics adapter The default vaule is PCI AGP Aperture Size It refers to a section of the PCI memory address range used for graphics memory It is recommended to leave this field at the default value unless the installed AGP card s specifications requires other sizes 29 AGP Mode The default value of this feature is set to Auto If you install an 8X AGP card on this motherboard you may select Auto 8X or 4X as the AGP mode If the installed AGP card is a 4X AGP card then you may set the AGP mode as Auto 4X 2X or 1X AGP Fast Write This allows you to enable or disable the feature of AGP fast write protocol support IDE Driving Strength Select Normal or Strong for IDE driving strength PCI Delay Transaction Enable PCI Delay Transaction feature will free the PCI Bus when the CPU is accessing 8 bit ISA cards Disable this feature when using ISA cards that are not PCI 2 1 compliant OnBoard LAN This allows you to enable or disable the onboard LAN feature OnBoard AC 97 Audio Select Enabled or Disabled for the onboard AC 97 Audio feature If you use an AMD 754 Pin CPU on the ASRock 754Bridge which is installed into the K8 BRIDGE on this motherboard you will see the below screen and configuration options for the Chipset Configuration BIOS SETUP UTILITY Advanced Chipset Settings To set DRAM Voltage Primary Graphics Adapter PCI AGP Aperture Size 64 MB AGP Mode Auto AGP Fa
28. ility Cool n Quiet Use this item to enable or disable AMD s Cool n Quiet technology Processor Maximum Multiplier It will display Processor Maximum Multiplier for reference Processor Maximum Voltage It will display Processor Maximum Voltage for reference Multiplier Voltage Change This item is set to Auto by default If it is set to Manual you may adjust the value of Processor Multiplier and Processor Voltage However it is recom mended to keep the default value for system stability BIOS SETUP UTILITY Advanced CPU Configuration If AUTO FID VID will CPU Host Frequency Auto be left at the rated Actual Frequency MHz 200 frequency voltage If Spread Spectrum Disabled Manual FID VID will Cool n Quiet Enabled be set based on User Processor Maximum Multiplier sail Selection in Setup Processor Maximum Voltage 1 550 V Processor Multiplier x8 Processor Voltage 1 500V Memory Clock Auto Select Screen Flexibility Option Disabled Select Item Bank Interleaving Auto Change Option Burst Length 8 Beats General Help oes patency CL Auto Load Defaults Auto Exit MA Timing BT Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Processor Multiplier This item will show when Multiplier Voltage Change is set to Manual otherwise it will be hidden You may set the value from x4 up to x25 but no higher than the value of Processor Maximum Multi
29. lots of the same color In other words you have to install identical DDR DIMM pair in Dual Channel A DDR1 and DDR3 Blue slots see p 8 No 7 or identical DDR DIMM pair in Dual Channel B DDR2 and DDR4 Black slots see p 8 No 11 so that Dual Channel Memory Technology can be activated This motherboard also allows you to install four DDR DIMMs for dual channel configuration and please install identical DDR DIMMs in all four slots You may refer to the Dual Channel Memory Configuration Table below Dual Channel Memory Configurations DDR1 DDR2 DDR3 DDR4 Blue Slot Black Slot Blue Slot Black Slot 1 Populated Populated 2 Populated Populated 3 Populated Populated Populated Populated 1 If you want to install two memory modules for optimal compatibility and reliability it is recommended to install them in the slots of the same color In other words install them either in the set of blue slots DDR1 and DDR3 or in the set of black slots DDR2 and DDR4 2 If only one memory module or three memory modules are installed in the DDR DIMM slots on this motherboard it is unable to activate the Dual Channel Memory Technology 3 Ifa pair of memory modules is NOT installed in the same Dual Channel for example installing a pair of memory modules in DDR1 and DDR2 it is unable to activate the Dual Channel Memory Technology 12 Installing a DIMM J Please make sure to disconne
30. mory Mode Select Field DIMM 256MB 166MHz DDR333 General Help DIMM None DIMM 3 256MB 166MHz DDR333 Save and Exit DIMM 4 None Function Description Moves cursor left or right to select Screens Moves cursor up or down to select items To change option for the selected items To bring up the selected screen To display the General Help Screen To load optimal default values for all the settings To save changes and exit the BIOS SETUP UTILITY To jump to the Exit Screen or exit the current screen SETUP UTILITY the Main screen will appear and display BIOS SETUP UTILITY H W Monitor Boot Security Use Enter TAB or SHIFT TAB to L 00 09 select a field Mon 08 02 2004 TORAS configure system Time Select Screen Select Item Change Field Load Defaults Exit v02 54 C Copyright 1985 2003 American Megatrends Inc System Time Hour Minute Second Use this item to specify the system time System Date Day Month Date Year Use this item to specify the system date 24 If you use an AMD 754 Pin CPU on the ASRock 754Bridge which is installed into the K8 BRIDGE on this motherboard you will see the below Main screen when entering the BIOS SETUP UTILITY BIOS SETUP UTILITY Advanced H W Monitor Boot Security Exit System Overview Use Enter TAB or SHIFT TAB to select a field 00 09 System Date Mon 08 02 2004 Use Her ri do configure system Time BIOS Version K7Up
31. n AMR slot Please do NOT insert any AGP card into the orange colored Bridge K8BRIDGE 1 and AMR card into the brown colored Bridge K8BRIDGE 2 It may cause permanent damage to the hardware CPU Type Jumper Settings 2 Pin Jumpers 3 Pin Jumpers 462 Pin CPU J2 J3 J14 J6 J7 J8 J9 J10 page 8 No 12 page 8 No 33 page 8 No 16 J11 J13 Default oo tt page 8 No 14 1 x 2 pin short AT 5 x 2 pin short Y gt pe 5 x 3 pin short pin1 pin2 1 x 3 pin short pin1 pin2 J4 J5 J12 page 8 No 13 page 8 No 19 EBEEBEE 353 2 DODD fe ooo 8 x 2 pin short 4 x 3 pin short pin1 pin2 J2 J3 J14 J6 J7 J8 J9 J10 754 Pin CPU page 8 No 12 page 8 No 33 page 8 No 16 J11 J13 ofe age 8 No 14 Using an add on 2 pag ap ASRock 754 Bridge 1 x 2 pin open 5 x 2 pin open Pop 5 x 3 pin short pin2 pin3 4 x 3 pin short pin2 pin3 J4 J5 J12 page 8 No 13 page 8 No 19 joe eee BEE lefelefe 8 x 2 pin open 4 x 3 pin short pin2 pin3 14 NOTE When adjusting the jumper settings you may use the tool Jumper Cap Remover to help you removing the jumper caps more easily This Jumper Cap Remover is bundled in your motherboard package and please follow the Jumper Cap Remover Instruction to use it properly PCI slots PCI slots are used to install expansion cards that have the 32 bit PCI interface AGP slot The AGP slots
32. ort 1 PS 2 keyboard port 1 serial port COM1 1 parallel port ECP EPP support 6 ready to use USB 2 0 ports 1 RJ 45 port Audio Jack Line In Line Out Microphone BIOS AMI BIOS Supports Plug and Play ACPI 1 1 compliance wake up events SMBIOS 2 3 1 support CPU frequency stepless control only for advanced users reference see CAUTION 5 OS Microsoft Windows 98SE ME 2000 XP compliant CAUTION 1 This motherboard supports Dual Channel Memory Technology Before you implement Dual Channel Memory Technology make sure to read the installation guide of memory modules on page 12 for proper installation 2 While CPU overheat is detected the system will automatically shutdown Before you resume the system please check if the CPU fan on the motherboard functions properly and unplug the power cord then plug it back again To improve heat dissipation remember to spray thermal grease between the CPU and the heatsink when you install the PC system 3 Do NOT use a3 3V AGP card on the AGP slot of this motherboard It may cause permanent damage 4 Power Management for USB 2 0 works fine under Microsoft Windows XP SP1 2000 SP4 It may not work properly under Microsoft Windows 98 ME 5 Although this motherboard offers stepless control it is not recommended to perform over clocking Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU The
33. plier For example if the value of Processor Maximum Multiplier is x11 the actual value of multiplier will be x11 even if you set this item to a value higher than x11 However for system stability it is not recommended to adjust the value of this item Processor Voltage This item will show when Multiplier Voltage Change is set to Manual otherwise it will be hidden You may set the value from 1 550V down to 0 800 V However for safety and system stability it is not recommended to adjust the value of this item 27 Memory Clock This item can be set by the code using Auto You can set one of the standard values as listed 133 MHz DDR266 166 MHz DDR333 200 MHz DDR400 Flexibility Option The default value of this option is Disabled It will allow better tolerance for memory compatibility when it is set to Enabled Bank Interleaving Interleaving allows memory accesses to be spread out over banks on the same node or accross nodes decreasing access contention Burst Length Burst length can be set to 8 or 4 beats CAS Latency CL Use this item to adjust the means of memory accessing Configuration options Auto 2 0 3 0 and 2 5 MA Timing Use this to adjust values for MA timing Configuration options 2T 1T The default value is 2T 28 3 3 2 Chipset Configuration BIOS SETUP UTILITY Advanced Chipset Configuration Flexibility Option Disabled 133MHz DDR266
34. port Legacy USB Support Use this item to enable or disable the support to emulate legacy I O devices such as mouse keyboard etc Or you may select Auto so that the system will start to auto detect if there is no USB device connected Auto option will disable the legacy USB support 37 3 4 Hardware Health Event Monitoring Screen In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperature motherboard temperature CPU fan speed chassis fan speed and the critical voltage BIOS SETUP UTILITY Main Advanced H W Monitor Security Hardware Health Event Monitoring CPU Temperature 37 C 98 F M B Temperature 31 C 87F CPU Fan Speed 2463 RPM Chassis Fan Speed N A Vcore 1 629V 3 30V 3 306V 5 00V 5 067V Select Screen 12 00V 11 890V Select Item General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 3 5 Boot Screen In this section it will display the available devices on your system for you to config ure the boot settings and the boot priority BIOS SETUP UTILITY Main Advanced H W Monitor Security Exit Boot Settings Configure Settings during System Boot gt Boot Device Priority gt Removable Drives Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American
35. r USB45 the USB ports 4 5 on ASRock I O Plus will not be able to function Infrared Module Header Pay This header supports an optional 5 pin IR1 L l a wireless transmitting and see p 8 No 28 ifolo receiving infrared module IGND IRRX Internal Audio Connectors Nr 4 pin CD1 4 pin AUX1 SE CD1 CD1 see p 8 No 40 These connectors allow you to receive stereo audio input from sound sources such as AUX1 see p 8 No 39 ARTS AUXI a CD ROM DVD ROM TV xida tuner card or MPEG card Front Panel Audio Header GND a This is an interface for the front 5 9 pin AUDIO1 BACKOUT R panel audio cable that allows BACKOUT L i see p 8 No 35 convenient connection and AUD OUT L GND AUD OUT R MIC POWER 19 control of audio devices System Panel Header 9 pin PANEL1 see p 8 No 22 This header accommodates several system front panel functions Chassis Speaker Header 4 pin SPEAKER 1 see p 8 No 24 SPEAKER DUMMY DUMMY 5V Please connect the chassis speaker to this header Chassis Fan Connector 3 pin CHA_FAN1 see p 8 No 21 IGND 12V CHA FAN SPEED Please connect the chassis fan cable to this connector and match the black wire to the ground pin CPU Fan Connector 3 pin CPU FAN1 see p 8 No 2 CPU FAN SPEED 12V jGND Please connect the CPU fan cable to this connector and match
36. r disable the PCI IDE BusMaster feature 3 3 6 Floppy Configuration In this section you may configure the type of your floppy drive BIOS SETUP UTILITY Advanced Floppy Configuration Select the type of S800 So floppy drive connected to the Floppy B Disabled system Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 35 3 3 7 Super IO Configuration BIOS SETUP UTILITY Advanced Configure Super IO Chipset Allow BIOS to Enable rr or Disable Floppy Controller Serial Port Address 3F8 IRQ4 Infrared Port Address Disabled Parallel Port Address 378 Parallel Port Mode ECP EPP EPP Version 1 9 ECP Mode DMA Channel DMA3 Parallel Port IRQ IRQ7 OnBoard Game Port Enabled Select S OnBoard MIDI Port Disabled eer Sereen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc OnBoard Floppy Controller Use this item to enable or disable floppy drive controller Serial Port Address Use this item to set the address for the onboard serial port or disable it Configuration options Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Infrared Port Address Use this item to set the address for the onboard infrared port or disable it Configuration options Disabled 2F8 IRQ3 and 2E8 IRQ3 Parallel
37. shows a 3 pin jumper whose pin1 Ga g ky and pin2 are Short when jumper cap is Short Open placed on these 2 pins Jumper Setting PS2_USB_PWR1 12 23 Short pin2 pin3 to enable see p No 1 oa em 5VSB standby for PS 2 5V 5VSB or USB wake up events Note To select 5VSB it requires 2 Amp and higher standby current provided by power supply JR1 JL1 nooo see p 8 No 36 JR1 JLi Note If the jumpers JL1 and JR1 are short both the front panel and the rear panel audio connectors can work Clear CMOS ojo CLRCMOS2 elo see p 8 No 26 2 pin jumper Note CLRCMOS2 allows you to clear the data in CMOS The data in CMOS includes system setup information such as system password date time and system setup parameters To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord from the power supply After waiting for 15 seconds use a jumper cap to short the Clear CMOS jumper for 5 seconds After shorting the Clear CMOS jumper please remove the jumper cap However please do not clear the CMOS right after you update the BIOS If you need to clear the CMOS when you just finish updating the BIOS you must boot up the system first and then shut it down before you do the clear CMOS action FSB_SELO na 12 2258 23 FSB SEL1 Fs seLo DE rs seLo BD rs seo OB rss seo COO 7 23 12 12 23 see p 8 No 10 rss seL1 OG rss se BG rs se BE fs set1 BE FSB
38. st Write Disabled IDE Drive Strength High PCI Delay Transaction Disabled OnBoard LAN Enabled OnBoard AC 97 Audio Enabled RER ea HT Width Auto 2 Change Option HT Speed Auto einen Save and Exit ESC Exit v02 54 C Copyright 1985 2003 American Megatrends Inc VCCM Use this to select VCCM voltage Configuration options are Auto High and Low The default value is Auto 30 Primary Graphics Adapter This item will switch the PCI Bus scanning order while searching for video card It allows you to select the type of Primary VGA in case of multiple video controllers AGP Aperture Size It refers to a section of the PCI memory address range used for graphics memory It is recommended to leave this field at the default value unless the installed AGP card s specifications requires other sizes AGP Mode The default value of this feature is set to Auto If you install an 8X AGP card on this motherboard you may select Auto 8X or 4X as the AGP mode If the installed AGP card is a 4X AGP card then you may set the AGP mode as Auto 4X 2X or 1X AGP Fast Write This allows you to enable or disable the feature of AGP fast write protocol support IDE Driving Strength Select Normal or Strong for IDE driving strength PCI Delay Transaction Enable PCI Delay Transaction feature will free the PCI Bus when the CPU is accessing 8 bit ISA cards Disable this feature when using ISA cards t
39. the black wire to the ground pin Game Connector 15 pin GAME1 see p 8 No 29 MIDI_OUT J2Y JBY MIDI_IN Connect a Game cable to this connector if the Game port bracket is installed ATX Power Connector 20 pin ATXPWR1 see p 8 No 38 20 Please connect an ATX power supply to this connector ATX 12V Connector VE Please note that it is necessary 4 pin ATX12V1 to connect a power supply with see p 8 No 6 ATX 12V plug to this connector so that it can provides sufficient power Failing to do so will cause the failure to power Up Power LED Header 1 Please connect a 3 pin power 3 pin PWR_LED1 blebs LED cable to this header see p 8 No 23 PERES 2 7 Serial ATA SATA Hard Disks Installation This motherboard supports Serial ATA SATA hard disks and RAID functions You may install SATA hard disks on this motherboard for internal storage devices This section will guide you to install the SATA hard disks STEP 1 STEP 2 STEP 3 STEP 4 Install the SATA hard disks into the drive bays of your chassis Connect the SATA power cable to the SATA hard disk Connect one end of the SATA data cable to the motherboard s SATA connector Connect the other end of the SATA data cable to the SATA hard disk 2 8 Hot Plug and Hot Swap Functions for SATA HDDs K7Upgrade 880 motherboard supports Hot Plug and Hot Swap functions for SATA Devices
40. the setup configurations 41 4 Software Support 4 1 Install Operating System This motherboard supports various Microsoft Windows operating systems 98 SE ME 2000 XP Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer to your OS documentation for more information 4 2 Support CD Information The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu did not appear automatically locate and double click on the file ASSETUP EXE from the BIN folder in the Support CD to display the menus 4 2 2 Drivers Menu The Drivers Menu shows the available devices drivers if the system detects installed devices Please install the necessary drivers to activate the devices 4 2 3 Utilities Menu The Utilities Menu shows the applications software that the motherboard supports Click on a specific item then follow the installation wizard to install it 4 2 4 Contact Information If you need to contact ASRock or want to know more about ASRock welcome to visit ASRock s website at http www asrock com or you may contact your dealer for further information 42
41. y Security Sccunes Install or Change the password Supervisor Password Not Installed User Password Not Installed Change User Password Clear User Password Select Screen Select Item Change General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 40 3 7 Exit Screen BIOS SETUP UTILITY Advanced H W Monitro Boot Security Exit Options Exit system setup after saving the changes Discard Changes and Exit Discard Changes F10 key can be used for this operation Load Optimal Defaults Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Save Changes and Exit When you select this option it will pop out the following message Save configuration changes and exit setup Select OK to save the changes and exit the BIOS SETUP UTILITY Discard Changes and Exit When you select this option it will pop out the following message Dis card changes and exit setup Select OK to exit the BIOS SETUP UTILITY without saving any changes Discard Changes When you select this option it will pop out the following message Dis card changes Select OK to discard all changes Load Optimal Defaults When you select this option it will pop out the following message Load optimal defaults Select OK to load the default values for all
Download Pdf Manuals
Related Search