Magma UPGTB2
Contents
1. Thunderbolt 2 Interface Card Thunderbolt 2 for EB1T INE NOTE The new Thunderbolt 2 Interface card comes with a standard bracket You need to replace this bracket with the shorter bracket in order to fit in the EB1T card guide slot 1 Remove the two mounting screws on the card 2 Slowly slide the bracket out from the card 3 Prepare the new bracket for EB1T Thunderbolt 2 Interface card as shown from the picture below 4 Properly align the mounting holes of the card on top of the bracket and secure it firmly Thunderbolt 2 Interface Card Thunderbolt M 2 for EB1T ho ssi G 5 Align the Thunderbolt 2 Interface card on top of the PCIE slot 6 Gently push the card into the PCIE slot make sure it is firmly seated 7 Reconnect the 3 pin wire power cable to Thunderbolt 2 Interface card see pictures below 8 Secure the Interface card Thunderbolt 2 Interface Card Thunderbolt M 2 for EB1T NOTE The new Thunderbolt 2 Interface card is shorter than the Thunderbolt 1 Interface card Thunderbolt 1 Thudembot l Thundebot 2 UD 1 0009003 A 0 0019008 2 Speed lOGfs Lo X4 124254362 Lanewidh of LEDs Thunderbolt 2 Interface Card Thunderbolt M 2 for EB1T 2 G Verify I nstallation Hardware Final step is to test and verify the Thunderbolt 2 Interface card When the Thun2. to return the product freight and duties paid Ship the well packaged product to the address below MAGMA RETURNS DEPT RMA Z 9918 Via Pasar San Diego CA 92126 USA It is not required though highly recommended that you keep the packaging from the original shipment of your Magma product However if you return a product to Magma for warranty repair replacement or take advantage of the 30 day money back guarantee you will need to package the product in a manner similar to the manner in which it was received from our plant Magma cannot be responsible for any physical damage to the product or component pieces of the product such as the host or expansion interfaces for the expansion chassis that are damaged due to inadequate packing Physical damage sustained in such a situation will be repaired at the owner s expense in accordance with Out of Warranty Procedures Please protect your investment a bit more padding in a good box will go a long way to insuring the device is returned to use in the same condition you shipped it in Please call for an RMA number first Thunderbolt 2 Interface Card How to Get More Help 18 MAGMA 9918 Via Pasar San Diego CA 92126 USA Toll Free 800 285 8990 US Main 858 530 2511 Fax 858 530 2733 www magma com no You QSG P N 09 09996 00
3. AMAGMA Thunderbolt 2 Installation Guide Thunderbolt 2 Interface Card MODELS ROBEN 3 TX TS TM EB1T and EB3T 2 G Contents Sarety WASH exesesekexkg ek pe ER EREIANEPF EE ERR TERRE E Sada RE 3 Thunder ror Pe 0 M 5 Gal erence 5 Thundgerboll 2 TO EB cous SON NON EE 8 Nek giclee E rr ne ee ee 8 THUNGerOOIE Z EB 11 Interface a Aa PI NN EUVEP 11 Veny HhstallatlOf ss see ekancieca xar ecce QR PO REOR ROC REOR EROR ER REX ECCE EC CHOC RR 15 TIEMPO mE 15 wie TO GCE ORS UU T LU TTE 18 Contacting recnnical SiDDOLDE vecta ds kd Tudor aaa cdam dus Qr Pda TRES tien 18 Returning Merchandise to 7 7 2202 22 2 4 18 Thunderbolt 2 Interface Card a Safety I nstructions Always use caution when servicing any electrical component Before handling the Magma Expansion chassis read the following instructions and safety guidelines to prevent damage to the product and to e
4. PCle slot 7 Reconnect the 3 pin wire power cable to Thunderbolt 2 Interface card see pictures below 8 Secure the Thunderbolt 2 Interface card Thunderbolt 2 Interface Card Thunderbolt M 2 for Roben 3 ne NOTE The new Thunderbolt 2 Interface card is shorter that the Thunderbolt 1 Interface card Thunderbolt 1 pT nderboltt 1 Thunderbot 2 UD 1 0009003 0 001008 2 Speed lOGfs X 2206s X4 X4 Laewit 2 of LEDs Thunderbolt 2 Interface Card zo Thunderbolt 2 EB3T Interface Card nstallation Uninstall the existing Thunderbolt Interface card in the chassis prior to installing the new Thunderbolt 2 Interface card WARNING High voltages are present inside the expansion chassis when the unit s power cord is plugged into an electrical outlet Disconnect the power cord from the AC outlet before removing the enclosure cover Turning the system power off at the power on off switch does not remove power to Warning components High voltage is still present 1 Remove the screw on top of the mounting bracket 2 Disconnect the 3 pin wire power cable from the Interface card as shown from pictures below 3 Gently pull the Thunderbolt 1 Interface card out in the PCle slot 4 Prepare the new Thunderbolt 2 Interface card Thunderbolt 2 Thunderbolt 2 Interface Card ne ssi 5 Align the Interfa
5. agma Serial 2 Service Ticket or Case if you already submitted an online request 3 Computer Type amp Model Operating System 4 Make amp Model of PCI PCle cards Application 5 Problem description When submitting an online technical support request always provide a valid working e mail address phone number shipping address and proper contact name Check your e mail for an automated response containing the case and updates You can also visit our web site at www magma com support For a quick response use the Technical Support and RMA Request Form available in the Support Section of the website Simply complete the form with all required information Please make sure that your problem description is sufficiently detailed to help us understand your problem Shipping or Transporting of Expansion Unit with PCI PCle cards Any PCle cards in should be removed or not to be installed prior to shipment to avoid or prevent possible damage Note Expansion board and PCle PCI cards that arrive damaged in shipment will not be covered under warranty Returning Merchandise to MAGMA If factory service is required a Service Representative will give you a Return Merchandise Authorization RMA number Put this number and your return address on the shipping label when you return the item s for service Magma will return any product that is not accompanied by an RMA number Please note that Magma WILL NOT accept COD packages so be sure
6. ce card top of the PCIE slot 6 Gently push the card until it is firmly seated in the PCle slot 7 Reconnect the 3 pin wire power cable to Thunderbolt 2 Interface card see pictures below 8 Secure the interface card Thunderbolt 2 Interface Card Thunderbolt M 2 for rem NOTE The new Thunderbolt 2 Interface card is shorter that the Thunderbolt 1 Interface card Thunderbolt 1 2 Thundebot 1 Thunderbot 2 UID 1 0009003 _ 0 0019008 2 0 05 Laewit 22 8 NN Thunderbolt 2 Interface Card Thunderbolt 2 Interface Card nstallation Remove Thunderbolt 1 Interface card in the chassis prior to installing the new Thunderbolt 2 Interface card WARNING High voltages are present inside the expansion chassis when the unit s power cord is plugged into an electrical outlet Disconnect the power cord from the AC outlet before removing the enclosure cover Turning the system power off at the power on off switch does not remove power to Warning components High voltage is still present 1 Remove the screw on top of the mounting bracket Disconnect the 3 pin wire power cable from the Interface card as shown from pictures below 2 1 Gently pull the Thunderbolt 1 Interface card out the PCle slot 2 Prepare the new Thunderbolt 2 Interface card Thunderbolt 2
7. derbolt 2 Interface card is fully operational the following GREEN LEDs are illuminated Solid Green see FIGURE A e Connect Thunderbolt cable to Magma Thunderbolt 2 Interface card use the bottom port Note You can use either top or bottom e Connect Displayport thunderbolt cable to available port You can skip this if external monitor is not available e Plug in power cord to Magma Thunderbolt 2 expansion unit e Two Green LEDs D6 3V3 and D8 3V3_STB are illuminated see FIGURE B e Connect the other end of Thunderbolt cable to laptop Thunderbolt port e Turn on the Laptop e Magma Thunderbolt 2 expansion unit powers up immediately 7 Green LEDs D1 D3 D4 D5 D6 D7 and D9 are illuminated This is with an external display attached as shown from the photo below FIGURE A e f you don t have an External display attached only 5 Green LEDs are illuminated see FIGURE C FIGURE A ru ou Mite IF 2122 dom aa f ig E a Ep p E CJ c E a Ur RIB om gt A iri 2 E 1 Thunderbolt 2 Interface Card Verify Installation 15 2 FIGURE B NOTE LEDs D6 and D8 are illuminated when power cord is attached to expansion unit This means the expansion unit is on standby mode If you don t see these TWO GREEN LEDs coming ON it means there is no power bei
8. ng supplied to the board Check 7 on the Interface card and make sure the 3 pin wire power cable is firmly connected If the two GEREN LEDs still not coming on you need to reseat the Thunderbolt 2 Interface card and remove amp reconnect the 3 pin wire connector to J 7 Thunderbolt 2 Interface Card Verify Installation IN 2 FI GURE If there is no Display Monitor attached to Thunderbolt 2 Interface card it would only show FIVE illuminated GREEN LEDs which is normal If you have a Display Monitor attached LEDs D1 and D5 should come on Otherwise the Thunderbolt 2 Interface card is not properly working or the monitor Displayport cable is faulty 04 8144 o 578 prts D 5 Menu me Rin e 7 A103 23 T y gt 114 SY oi ads reg EN i C 129 Rizs 2 nunderbolt 2 Express Thunderbolt 2 Interface Card Verify Installation ssi G How to Get More Help You can visit the Magma Technical Support FAQ pages on the Internet at www magma com support Contacting Technical Support Our support department can be reached by fax at 858 530 2733 or by phone at 858 530 2511 Support is available Monday through Friday 8 00 AM to 5 00 PM PT When contacting MAGMA Technical Support make sure to include the following information Exact and correct M
9. nsporting a sensitive component first place it in an anti static container or packaging e Handle all sensitive components at an ESD workstation If possible use anti static floor pads and workbench pads e Handle components and boards with care Don t touch the components or contacts on a board Hold a board by its edges or by its metal mounting bracket Thunderbolt 2 Interface Card 4 Thunderbolt 2 Roben 3 Interface Card nstallation Uninstall the existing Thunderbolt Interface card in the chassis prior to installing the new Thunderbolt 2 Interface card WARNING High voltages are present inside the expansion chassis when the unit s power cord is plugged into an electrical outlet Disconnect the power cord from the AC outlet before removing the enclosure cover Turning the system power off at the power on off switch does not remove power to Warning components High voltage is still present 1 Remove the screw on top of the mounting bracket 2 Disconnect the 3 pin wire power cable from the Interface card as shown from pictures below 3 Gently pull the Thunderbolt Interface card out in the PCle slot 4 Prepare the new Thunderbolt 2 Interface card see picture below Thunderbolt 2 Thunderbolt 2 Interface Card Thunderbolt 2 for Roben 3 5 2 5 Align the Thunderbolt 2 Interface card on top of the PCIE slot 6 Gently push the card until it is firmly seated in the
10. nsure your own personal Safety Refer to the Advisories section for advisory conventions used in this manual including the distinction between Danger Warning Caution Important and Note 1 Always use caution when handling operating the computer Only qualified experienced authorized electronics personnel should access the interior of the computer and expansion chassis WARNING Never modify or remove the radio frequency interference shielding from your workstation or expansion unit To do so may cause your installation to produce emissions that could interfere with Warning other electronic equipment in the area of your system When Working I nside a Computer 1 Before taking covers off a computer perform the following steps 2 Turn off the computer and any peripheral devices 3 Disconnect the computer and peripheral power cords from their AC outlets or inlets in order to prevent electric shock or system board damage In addition take note of these safety guidelines when appropriate 6 avoid possible damage to systems boards wait five seconds after turning off the computer before removing a component removing a system board or disconnecting a peripheral device from the computer B When you disconnect a cable pull on its connector or on its strain relief loop not on the cable itself Some cables have a connector with locking tabs If you are disconnecting this type of cable press in on the locking tabs befo
11. re disconnecting the cable As you pull connectors apart keep them evenly aligned to avoid bending any connector pins Also before connecting a cable make sure both connectors are correctly oriented and aligned CAUTI ON Do not attempt to service the system yourself except as explained in this manual Follow installation instructions closely Caution Thunderbolt 2 Interface Card a Protecting Against Electrostatic Discharge Electrostatic Discharge ESD Warning Electrostatic Discharge ESD is the enemy of semiconductor devices You should always take precautions to eliminate any electrostatic charge from your body and clothing before touching any Warning semiconductor device or card by using an electrostatic wrist strap and or rubber mat Static electricity can harm system boards Perform service at an ESD workstation and follow proper ESD procedures to reduce the risk of damage to components Magma strongly encourages you to follow proper ESD procedures which can include wrist straps and smocks when servicing equipment You can also take the following steps to prevent damage from electrostatic discharge ESD e When unpacking a static sensitive component from its shipping carton do not remove the component s anti static packaging material until you are ready to install the component in a computer Just before unwrapping the anti static packaging be sure you are at an ESD workstation or are grounded e When tra
Download Pdf Manuals
Related Search